Search Documents

By Ning Wang, Tengfei Guo, Wanyan Li, Hanjie Wen, Hannian Gu, Zehai Li

Bauxite residue (red mud) is an alkaline waste derived from the industrial process for extraction of alumina from bauxite ore. Some bauxite residues contain considerable concentrations of critical metals, for example, rare earth elements. Lithium in red mud was also reported as a potential resource. In the current study, a Li-rich red mud was leached using acetic acid to investigate the leaching behavior of lithium followed by neutralizing with hydrochloric or oxalic acid. By neutralizing red mud using diluted hydrochloric acid (0.01 mol/L), 58.04–60.27% of lithium was leached using 25% acetic acid at 95 °C for 60 min. In the meantime, more than 95% of sodium and 85% of calcium were also dissolved in the leachate solution. While oxalic acid (0.5 mol/L) was used to neutralize red mud prior to acetic acid leaching, lithium performed lower leaching efficiencies (42.41–46.88%) in comparison of using of hydrochloric acid–neutralized red mud. Nevertheless, these leaching efficiencies of lithium were close to that of calcium and much higher than those of sodium under the condition. In this study, 25% (v/v) of acetic acid, at 85 °C for 60 min, was demonstrated as optimum conditions for lithium extraction from oxalic acid–neutralized red mud using acetic acid. The results would be useful and of interest for lithium recovery and purification from red mud.

By Don C. White

The Vulture mine near Wickenburg, Arizona was a major gold producer from 1863 to 1942, having yielded about 11t(12.1 st) Au and 8t (8.8st) Ag. Gold occurs as coarse native metal and electrum in quartz veins and also finely dis¬seminated within a quartz monzonite sill and its silicified wall rock. The sill is semi-conformable within a Proterozoic volcaniclastic-dominated sequence, all dipping north about 35°. Early mining focused on the vein-hosted gold, particularly in the immediate hanging wall and footwall of the sill. Later efforts included some open-pit mining of the outcropping sill and adjacent altered and mineralized rock. Two sets of post-mineral faults have complicated the orebody geometry. The sill is a 350 m (1148 ft) long apophysis from a quartz mozonite stock to the west of the mine area. The stock has been dated at 85 my and contains abundant lesser gold occurrences in its core and about its margins. The Proterozoic rocks are notably lean in precious metals except where altered in proximity to the Creataceous stock and sill. Circumstances dictate an interpretation of epigenetic mineralization related to the Laramide intrusion.

Jan 1, 1990

By Ingunn Opland, Silje M. Tinderholt

Drill and blast project in Norway’s capital. The contract consists of 7 rock caverns (350–950 m2), 9.2 km tunnels, and four shafts. With 110 blue-collar and 31 white-collar, the project produces an average of 16–21,000 m3 hard rock per week, with a total of 19 tunnel faces. Weekly, nine grouting rounds for water control, 800 m3 shotcrete, and 1,200 bolts are required, and 60 trucks leave the site pr. day. Challenges include blasting in densely populated areas, planning and coordination to maintain high production, obtaining a CEEQUAL certification of very good, and transporting rock on Oslo’s main highway.

Jun 13, 2023

By Ven Mercade

The flotation of calcite has been studied by many investigators, especially in terms of type of collector; pH; and metal ions that activate and, more importantly, depress the flotation of calcite (1)(2). Research was extended to the investigation of the effect of polyvalent metal salts and sodium silicate using these materials added separately or in mixtures (3)(4)(5)(6). Flotation of calcite was also studied with respect to its function as a carrier in the beneficiation of kaolin clays by Ultraflotation (7) (8) (9). The carrier used in Engelhard Minerals & Chemicals Corporation's industrial Ultraflotation operation is calcite. This fact, coupled with the continuing interest in Ultraflotation phenomena, led to a study to determine the effect of polyvalent metal-silicate hydrosols on the flotation of calcite.

Jan 1, 1978

By L. A. Ruth

Vision 21 is a government/industry/academia cost-shared partnership to develop the technology basis for integrated energy plants that will, early in the 21stcentury, result in the deployment of ultra-clean plants that produce electricity and “opportunity” products. Vision 21 plants will use fossil fuel feed-stocks in combination with other domestic resources, e.g., biomass, municipal waste, and petroleum coke. Opportunity products could include transportation fuels, steam, high-value chemicals, synthesis gas, and hydrogen. Performance targets for Vision 21 plants, example plant configurations, and the key technologies that will be needed are described.

Jan 1, 2000

By Christopher J. Bise

INTRODUCTION Before a mine is planned in detail, a preliminary analysis is often conducted. This preplanning permits the mining engineer to make a rapid assessment as to whether or not a particular mining property warrants further consideration. In fact, a properly conducted preplanning phase can come within 10% to 20% of the actual results, thereby saving the mining engineer valuable time before committing himself to a fine-tuned analysis. The questions to be answered by mine preplanning are (1) What will be the operating conditions for the mine? and (2) How long will it take to complete the project? To answer these questions, calculations dealing with reserve estimation, production planning, man- power planning, and project scheduling are conducted. The following sections discuss these various phases of mine preplanning in greater detail. RESERVE ESTIMATION The estimation of the various characteristics of a reserve, such as quantity, grade, and thickness, is an ongoing process throughout the life of a mining venture. However, the reserve-estimation phase of mine planning is more closely associated with the preplanning phase. There are many different techniques employed in reserve estimation of solid mineral deposits; variations among them are introduced because of such considerations as ease of application or level of accuracy. In any event, each technique is developed in the following manner: (1) the mineral body is represented pictorially and then subdivided into blocks related to one or more samples of exploration data, (2) the area and volume of each block is determined, (3) the volumes are converted to representative tonnages (or, for example, grades), and (4) the results are tabulated. To illustrate this procedure, the polygonal (area-of- influence) technique will be presented due to its ease of application, flexibility in dealing with different deposits, and general acceptance. The polygonal method assumes that all characteristics of a mineral body extend halfway between a point of observation and any other point of observation. The explored portion of the mineral body is represented by polygonal prisms whose depths relate to the characteristic in question (grade, thickness, etc.) and whose plane bases relate to the area of influence of each point of observation (drill hole, etc.) as shown in Fig. 1. The polygons must be constructed in a definite order, usually clockwise and from the periphery to the center of the deposit. Table 1 can then be used to calculate the characteristics in question. Since, by definition, the polygonal method assumes that the characteristics of a mineral body extend half- way between points of observation, it becomes readily apparent that the evaluation of a vertical-drill hole exploration program requires that the sides of the polygons be formed by the intersection of perpendicular bisectors (Fig. 2). Figs. 3 and 4 show correct and incorrect construction of the polygons. The criterion for correct construction of the polygons is that all points within a particular polygon must be closer to its rallying point than those located in any other polygon. This is clearly not the case for certain points that are located in the polygon containing rallying point B in Fig. 4. Although this method can be used where the drill holes are irregularly spaced, calculations become less tedious when a square net (Fig. 5) or a chessboard (Fig. 6) grid is adopted. The numbers shown in Figs. 5 and 6 represent the relative weight for each of the shaded areas. In general, the greater the number of polygons, the more continuous the mineral body, and the more regular the grid, then the more accurate the computations will be. PRODUCTION PLANNING Before an acceptable evaluation of the production potential of a mine can be determined, a thorough exploration program should be conducted. It seems obvious that the nature and properties of the deposit and adjacent strata, the presence of impurities, and other mining conditions should be adequately determined prior to production planning and equipment selection. The lack of sufficiently detailed knowledge of the many mining parameters has led to the failure of numerous operations. For example, targeted production tonnages and equipment sizes for a coal mine are intimately related to the seam thickness. Needless to say the quality of information that is gathered from an exploration program can have a tremendous impact on the production plan. Production plans are developed initially by determining reasonable shift tonnages per operating section. Most of the time these values are developed from his-

Jan 1, 1986

By S. Frimpong

Shovel excavation constitutes a significant component of production costs in any surface mining operation. This makes shovel loading an important cost center that needs to be improved to lower production costs. Optimization of tool design will improve energy efficiency in earthmoving operations. However, modeling the soil-tool interaction is a complex process due to the fact that forces for excavating particulate material are functions of many variables. The magnitude of this resisting force depends not only on the type of soil but on the size, shape and orientation of the cutting element. Moreover, part of this complexity is attributed to the fact that the behavior of the material during excavation is not yet well understood. For the past five decades, researchers have mostly used the passive earth pressure theory to study the soil failure patterns around a cutting tool and to develop force prediction models for design optimization with some success. Although the force models developed from the passive pressure theory have been successful to some extent, they can hardly be extended to a general case because of the underlying assumptions and simplification of tool shapes. This paper aims at reviewing some of the existing empirical and analytical methods of cutting and excavation tool modeling with a focus on their merits and limitations. The paper also explores the use of numerical methods, specifically the discrete element method, for dealing with the unresolved aspects of soil dynamics in excavation.

Jan 1, 2011

By R. L. Virta

Common clay is a natural, fine-grained material composed of hydrous aluminum silicates. Shale is a laminated sedimentary rock that is formed by the consolidation of clay, mud or silt. Production About 160 companies produced common clay and shale in 41 states. In states not reporting production, common clay and shale probably was mined and sold for construction applications by companies not participating in the U.S. Geological Survey’s canvass of producers.

Jan 1, 2005

By H. Lawson

The Mine Safety and Health Administration (MSHA) issued Program Information Bulletin P09-03in April of 2008, providing formal guidance on using programs that model the redistribution of stress during underground mining of coal. A key part of this guidance is visual observation and mapping of ground conditions. If a correlation between ground conditions and model output can be established, the model is considered to be verified, and can be used to guide mine design in similar ground. A simple scale is recommended for ranking observed roof, rib, and floor conditions. This paper discusses optimization and implementation of a ground condition rating scheme in the gateroads of a deep underground longwall coal mine. Roughly 80% of each gateroad length deteriorated in a fairly uniform manner. However, this manner varied between gateroads, as did pillar size. The implementation of a ground condition mapping program, similar to that recommended in PIB 09-03, was successful in characterizing the ground response to mining in gateroads of a longwall coal mine.

Jan 1, 2012

Gangue-cemented paste backfill (GCPB), is a well-established green mining technology and significantly improves the recovery rate of mineral resources, prevents mine dynamic disasters, reduces surface subsidence, and consumes a considerable amount of solid waste. The addition of an early strength agent as an additive in cement-based materials provides several security, technical, and economic advantages. In this study, the early strength agent on the early age (3, 7 and 28 days) strength of GCPB is evaluated experimentally. The GCPB specimens have an initial sodium sulfate early strength agent concentration of 0%, 1%, 2%, 3%, and 4%, and the obtained samples were analyzed by testing for uniaxial compressive strength (UCS) and scanning electron microscopy (SEM). The test results show that the UCS of the GCPB specimens with sodium sulfate is much higher than that of the blank specimens. When cured for 3 days and 7 days, the strength of GCPB with 2% sodium sulfate increased the most, by 131% and 116% respectively. When cured for 28 days, the strength of GCPB with 1% sodium sulfate increased by 135%. Scanning electron microscopy (SEM) results showed that the GCPB with 1% and 2% sodium sulfate had better internal structure compactness, thicker acicular crystals, and more flocs. As a kind of early strength agent, sodium sulfate can react with calcium hydroxide to generate calcium dihydrate sulfate and then react with calcium aluminate; the hydration product (C3A) quickly generates calcium sulfoaluminate hydrate (AFt) needle-shaped crystals, forming an early skeleton and improving the early strength.

Jan 7, 2020

By D. Komljenovic, V. Kecojevic

Selection of the best possible truck type (model) is of crucial importance for the mine decision-makers. In this paper, authors contribute to the body of knowledge by developing a novel methodology for the selection of mining truck. Both the Coefficient of Technical Level (CTL) and Analytic Hierarchy Process (AHP) methods were used in this study. The CTL represents a mathematical function which takes into consideration the interrelations among the main technical parameters of mining trucks. The authors developed a hierarchical structure where both attribute categories and their importance, i.e. priority or weight in the selection process were determined. For each category, a number of sub-attributes and their priorities were assigned, and a pairwise comparison among them was performed using the AHP method. In the final part of the study, the CTL was integrated into the AHP and represents a holistic approach in the selection of mining trucks. A case study on 180 tonnes truck category offered by five manufacturers was carried out. A sensitivity study of obtained results was also performed indicating a very stable solution. The methodology presented in this paper may be used by mining operators to help in the selection of a specific type when acquiring a new truck. It may also be used by equipment manufacturers to help in analysis of potential benefits of envisaged modifications concerning an existing truck type and/or development of a new type.

Jan 1, 2007

By F. Calizaya

This paper describes the basic requirements for the utilization of belt air to ventilate working sections at remote locations in relation to the main fans. It highlights the risks involved, potential problems, and the provisions that must be followed by mine operators for the safe use of belt air. The paper also presents a brief review of the current regulations, conveyor belting tests, atmospheric monitoring system requirements, and the experience gained by mine operators to utilize the belt entries to ventilate remote working sections or areas where mechanized equipment is being installed or removed. The paper concludes with a set of recommendations with respect to the utilization of belt air and the composition of belt material in under-ground coal mines.

Jan 1, 2008

By M. S. Klima, V. Choudhry

Coal gasification solid residue (slag) contains unconverted carbon (char) which is considered an impurity for utilization applications of slag. Under this study, table concentration was used to process approximately 24,000 pounds of a nominal -3.4 mm gasifier slag (~85% ash) to separate high (~100%) ash slag from low (~50%) ash char. The results indicated a nearly ideal separation of the slag from the char for sizes coarser than about 1 mm. An overall slag yield of 71% was obtained. The slag was sufficiently clean to be used as feed material for the production of expanded lightweight aggregate. The recovered char had an ash content of about 47% and was a nominal -1 mm in size.

Feb 24, 1997

By W. Z. Rogers

U.S. feldspar output sold or used in 2004 was estimated to be 790 kt (871,000 st), valued at $43 million free-on-board plant. This was below 2003 and about the same volume as 2002. The strong housing market in the United States maintained demand for ceramic tiles, plumbing fixtures, and fiberglass insulation requiring feldspar and shipments of glass containers increased by about 4 percent. Imports of ceramic tiles and plumbing fixtures continue to increase, taking the place of U.S. produced goods, and the feldspar required to make them. Output included flotation concentrates, feldspar content in feldspar-silica mixtures, potash feldspar and aplite.

Jan 1, 2005

By Fred N. Kissell

INTRODUCTION During the last few years, several new ventilation developments have attracted the interest of mining engi¬neers. Some of these developments are applicable pri¬marily to hard-rock mining, while others are more applicable to coal mining. STOPPINGS Parachute Stopping The parachute stopping is a new type of quick-erect stopping that is intended for temporary use in hard-rock mines (Kissell, Thimons, and Vinson, 1975). As shown in Fig. 1, the stopping is shaped very much like an ordinary parachute, with a canopy of impermeable fabric that is sewn to regularly spaced straps running to a common point. To erect the stopping, the straps are attached to a fixed anchor point such as a roof bolt, and the edge of the canopy is lifted into the moving air¬stream. The airstream pops the parachute canopy into place, and the differential air pressure across the stop¬ping holds it in place, forcing the fabric against the walls, roof, and floor of the mine opening. The principal advantage of the parachute stopping is that it requires only a few minutes to install, making it a great time-saver for emergency use or for day-to¬day changes in ventilation during the production cycle. However, the parachute stopping does require some minimum air velocity to lift it and some minimum differential pressure to hold it in place. For a fabric weighing 0.27 kg/ m2 (8.0 oz per sq yd), the minimum air velocity is about 0.5 m/s (100 fpm), and the mini¬mum differential pressure is about 0.05 kPa [0.2 in. water gage (WG) ]. There is always some air leakage around the stop¬ping, mainly depending upon the extent to which pipes or other obstructions encumber the airway and prevent good sealing. Leakage of a few cubic meters per second (a few thousand cubic feet per minute) can be expected, unless foam is used to improve the seal at the edges of the canopy. Quick-Fix Blowout Stopping The quick-fix blowout stopping is a variation of the parachute stopping (Thimons and Kissell, 1976), and it is used in the proximity of blasting operations. This type of stopping is designed to be blown out easily by the blast forces, and it may be reinstalled quickly and easily. The long high-strength straps of the parachute stopping are replaced by groups of short straps that tear easily. These straps are attached at six equally spaced locations around the perimeter of the canopy. To erect the stopping, one strap of each of the six groups is fastened to the mine wall, roof, and floor by using spads, by setting pins with a powder-actuated gun, or by tying the straps to some firm anchor point. Once the straps have been attached, the differential air pressure across the stopping, which must be at least 0.025 kPa (0.1 in. WG), forces the stopping perimeter against the mine walls, thus creating the air seal. It is the self-sealing feature of this stopping that makes it a significant time-saver. Only a few attachment points are needed; in many cases, four attachment points are sufficient, since the stopping naturally tends to form a seal with the airway surfaces. When nearby produc¬tion blasting exerts excessive forces on the stopping, one or more of the straps tears away from its attachment point, protecting the stronger canopy from damage. Damage-Resistant Brattice The damage-resistant brattice is a stopping that is designed for use in mines such as salt and limestone mines where the differential pressures are low and the roof is relatively flat. As shown in Fig. 2, the damage-resistant brattice consists of a series of brattice panels that are hung vertically and joined by Velcro® connections. When the brattice is subjected to strong blast forces, the Velcro® connection peels apart and allows the panels to open without incurring damage. The Velcro® connections can be resealed by hand within a matter of minutes. Such damage-resistant brattices have withstood the blast effects of 318 kg (700 lb) of ammonium nitrate-fuel oil (ANFO) explosive detonated as close as 91 m (300 ft) from the brattice. Ordinary brattice cloth is used for the panels, with a 51-mm (2-in.) wide strip of Velcro® hooks sewn along one edge of the length, and a 51-mm (2-in.) wide strip of Velcro® pile sewn along the other edge. Both the hooks and the pile are sewn onto the same side of the brattice cloth. The resulting Velcro® seal formed be¬tween adjacent panels is perpendicular to the brattice itself, and the leading edge of the seal can be directed either toward or away from the blast forces; the brattice works equally well in either case. To hang the brattice, panels of brattice cloth about 0.9 m (3 ft) longer than the height of the airway are cut from a 1.8-m (6-ft) wide roll. The additional 0.9 m (3 ft) of brattice cloth allows 0.3 m (1 ft) for attachment to the roof by means of a board, with 0.6 m (2 ft) for forming a good air seal at the floor. Each brattice panel is wrapped once or twice around a 51 X 102 mm (2 X 4 in.) or 25 X 76 mm (1 X 3 in.) mounting board that is 254 to 305 mm (10 to 12 in.) shorter than the width of the panel. For convenience in

Jan 1, 1982

By J. Hunter, E. Jackson

This paper describes work done by Placer Dome Technical Services Limited, a subsidiary of Barrick Gold, and Nautilus Minerals Inc. in support of the conceptual design of a subsea mining system. It describes an overall concept design plus specific studies into mechanical excavation at depth. The concept design includes one or more subsea excavators connected to a suction riser, which transports the cut material to a shipboard dewatering and offloading system. A multi-phase investigation was performed into the mechanical excavation of seafloor massive sulphides at depths of around 1600m. Rock samples were recovered and tested for rock properties and cutting behaviour. A small pick drum cutter was procured and tested on a representative concrete slab in a lab and tested again while submerged in a test tank. Finally the cutter was tested on a massive sulphide ore body at 1600m depth. The cutting performance results, e.g. pick forces and specific energies, should provide valuable input to the design of future full scale subsea mining systems.

Jan 1, 2007

By Steven G. Vick

Effects of the August 1995 failure of the Omai tailings dam in Guyana continue to be felt throughout the mining industry. This article is taken from the final report of the independent body of experts commissioned by the government of Guyana to establish the cause of the failure. It explains what happened, why and how to avoid it in the future. Despite environmental, health and safety effects that were negligible by any objective measure, the failure has received wide international attention. Coming on the heels of the shift in exploration targets and development opportunities to developing countries, it has intensified interest in tailings dam safety and environmental management issues. An informed understanding of the nature of the failure and its effects is key to responding to these concerns.

Jan 1, 1996

By S. Shi, J. Y. Hwang, B. Li

Silver, copper, and zinc are commonly known elements with antibacterial and antifungal capabilities. Attempts have been made to dope silver on minerals, glass, and ceramics and the resulting materials have been investigated for their antibacterial and antifungal properties. Since silver is expensive and very reactive, silver doped materials have been found inappropriate in some applications. Copper-vermiculite is investigated as an alternative. Vermiculite has high cation exchange capacity on the magnesium ion in the crystal structure. Copper ion may have a high tendency to replace magnesium because of similar charge interference and ionic radius. Copper-vermiculite is prepared by reacting vermiculite and copper chloride solution. By impregnating copper ions into the nanometer openings between the layers of vermiculite, it is possible to render the composite with antibacterial functions if the copper ions could be released gradually from the composite. The antibacterial efficiency of Cu-vermiculite against Escherichia coli was studied using the Halo method. The results show that Cu-vermiculite is effective for preventing the reproduction of the bacteria. Heat treatment of Cu-vermiculite at up to 400°C does not show significant changes in antibacterial activities.

Jan 1, 2002

By Jamal Rostami, Ataollah Rahbar, Jürgen Paulzen

"Uma Oya Multipurpose Development Project is located in South West Sri Lanka. This project, among many components, involves a 14 km headrace tunnel in very hard and abrasive igneous rocks. The tunnel is under construction by a 4.4 m diameter double shield TBM. The headrace tunnel has already reached 5km milestone and has passed through some reaches of tunnel in very strong intact rocks with no joints. Low penetration at high thrust load has caused frequent stoppages for cutter change leading to low utilization and advance rates due to low cutter life. The original machine was dressed with 27, each 432 mm (17 inch) diameter, 19 mm (3/4 inch) tipped disc cutters. However, various cutter diameters of 432-457 mm (17-18 inch) and cutter tip widths 13 to 19 mm (0.5-0.75 in), have been tried to see if cutter life and penetration rates could be increased. This paper will review the history of the project, the geology of the site, along with TBM performance and cutter life. It will focus on frequency of different cutter failures encountered in various ground conditions. Also, results of using variation of cutter diameter and tip width to cope with the hard rock conditions and their results in increasing machine productivity will be discussed. This allows for better understanding of parameters controlling disc wear/life and leads to better cutter management for more efficient operation of hard rock TBMs in similar conditions. INTRODUCTION The Uma Oya Multipurpose Development Project (UOMDP) lies in the south-eastern part of the central highland region of Sri Lanka. The Multi-Purpose Project Of Uma Oya is planned to convey water from Uma Oya to Kirindi Oya Basin for hydroelectric energy generation includes Puhulpola RCC Dam on the Uma Oya river, Dyraaba RCC Dam on the Mahatotilla Oya river, a conveyance tunnel from Uma Oya to Mahatotilla Oya (L=3750m), a long feeder tunnel from Mahatotilla Oya to Kirindi Oya river. The feeder (or power) tunnel Lot consists of a 15554 m long headrace tunnel (HRT), the surge shaft and tank on the upstream of the vertical shaft, a 650 m vertical shaft with steel lining, and an underground powerhouse and a 3650m tailrace tunnel (TRT)."

Jan 1, 2016

By Umay Cinarli, Ahmet Turan

High-energy consumption in primary aluminum production (from bauxite ores) makes secondary aluminum production (from metallic raw materials such as scrap and dross) very critical. Aluminum dross, as a waste, arises in pyrometallurgical processes, and it is the mixture of metallic Al, Al2O3, other metal oxides, metal halides, and some other compounds like AlN. Aluminum dross has two subgroups (white and black) with respect to its metallic aluminum content. White dross is a secondary aluminum resource because of its high metallic aluminum content, whereas black dross, having low metallic aluminum content, is generally disposed in dumping areas. In the present study, it was aimed to develop a simple technique to valorize aluminum black dross in the form of alumina-based ceramic materials through pyrometallurgical (calcination) and hydrometallurgical (leaching) operations. Moreover, thermochemical simulations were conducted by using HSC Chemistry 6.12 software to simulate calcination conditions. After leaching experiments, an alumina-based ceramic containing approximately 36.8% Al2O3, 61.4% MgAl2O4 with 1.8% Na2FeO4, which might be available to use as a spinel refractory in steel smelting furnaces, was obtained in the experiment carried out in a solution containing 10 mLH2SO4 and 40 mL distilled water (3.5 M). Moreover, the sinterability of the alumina-based ceramic was investigated at the temperatures from 1350 to 1550 °C. In the sample which was sintered at 1550 °C, a density value of 3.15 g cm−3 and a hardness value of 69.58 HV were measured.

Oct 26, 2020