Search Documents

By S. K. Oraee

Managers always look for systems with minimum hazards. The hazards create problems for performance of projects. The largest and most important hazards of working underground mine can be related to health, safety and environmental, because if one of these sectors be in hazard, maybe lead to close mine. Failure mode and effects analysis (FMEA) is a widely used quality improvement tool to identify the potential failure modes for measuring reliability of a product or a process. FMEA is performed by developing a risk priority number (RPN), which is the product of severity, occurrence, and detection ratings. On the other hand, with regard to uncertainty in the decision-making, fuzzy theory will be able to model this uncertainty. Fuzzy FMEA provides a tool that can work in a better way with vague concepts and without sufficient information than conventional FMEA. This article by using Fuzzy FMEA and based on HSE criteria evaluate hazards of Parvade No. 1 Mine in Tabas Coal Mine. The results demonstrate the most hazardous parameter is rock burst in this mine.

Jan 1, 2011

By Bobby C. Carson

INTRODUCTION The National Park Service is entering the seventh year of monitoring caves for the presence of radon and radon daughter products. The purpose of this paper is to summarize the radiation monitoring program at Mammoth Cave National Park, and to present some of the results of this program. Mammoth Cave National Park completed five years of collecting data on May 1, 1981: although Mammoth Cave encompasses approximately 361 km of underground passageways, this paper will concentrate on only a 2.2 km section of the cave known as the Historic Tour. Included in this paper is a discussion of the methods the Nations Park Service uses to protect employees from exposure to alpha radiation. MONITORING METHODS The National Park Service monitors cave atmospheres utilizing the procedures provided by the Mine Safety and Health Administration in their Radiation Monitoring Training Manual (Anon., 1976). This procedure is described as the Kusnetz Method (Kusnetz, 1956) of radon daughter monitoring. Due to the length of the tours at Mammoth Cave, it has been determined to be the most practical procedure. The Historic Tour is a 2.2 km (1.4 mile) loop through passageways ranging in size from 18 m high by 12 m wide, to 0.9 m high by 0.6 m wide. Seven five minute walking samples were taken for this cave tour by drawing at least 10 1 of air through a 25 mm fiberglass filter utilizing a Monitaire Sampler Pump. The radon daughter concentration levels were determined using an alpha scintillation counter to measure the alpha activity on the filter paper. The Monitaire Sampler Pump was calibrated each day prior to monitoring the cave tour and the scintillation counter was calibrated by procedures described by the Mine Safety and Health Administration (Beckman, 1975) at six month intervals. Guidelines established by the National Park Service and approved by the Mine Safety and Health Administration require weekly sampling when the average working level exceeds 0.30 (NPS-14, 1980). A working level is an atmospheric concentration of radon (Rn-222) daughters which will deliver 1.3 x 10 5 MeV of alpha energy per liter of air in decaying through Ra C' (Po-214). The Historic Tour has continually exceeded the 0.30 working level average and has been monitored weekly. Generally, only radon daughter working level data has been collected on the Historic Tour due to limited personnel. However, other special measurements of the uncombined fractions of radon daughters with wire screens, tsivoglou method for radon daughter sampling (Thomas modification, 1970), and thoron daughter monitoring. These special measurements have not been routine due to time limitations involved in radon daughter sampling of other occupied portions of the cave. SUMMARY OF DATA The Historic Tour has been the most consistantly monitored tour since elevated levels of alpha radiation were found to exist at Mammoth. Cave. It is also the only natural entrance to the main sections of the cave and provided an opportunity to study man made actions upon the natural entrance. For these reasons the Historic Tour was isolated for study. Beginning October 10, 1977, and ending November 20, 1977, a pilot project was undertaken involving the Historic Tour and the practice of covering the natural entrance to this tour with sheet metal in the winter months. The purpose was to study radiation levels on the Historice Tour while the covers were on and off the natural entrance. In this pilot project, comparisons were made with incast air with covers on and off the entrance, and outcast air with covers on and off the entrance. TABLE 1 Incast air Mean W.L. Covers on . . . . 1.46 W.L. Increased 54% Covers off. . . . 0.67 W.L. when covers on Outcast air Mean W.L. Covers on . . . . 1.33 W.L. Decreased 5% Covers off. . . . 1.40 W.L. when covers on The natural entrance was artificially covered in the winter months (Yarborough, 1978) to protect the visitor from the extremely cold incast air, in the first four years of monitoring. The data in Table 1, illustrated in Figures 1 and 2, shows that this action increased the radon daughter working levels on the Historic Tour by 54% when the covers were on the entrance and the airflow was incast. While the air flow was outcast at the natural entrance, it made little difference as to whether the entrance was closed or open. Some interesting findings were observed when

Jan 1, 1981

By K. Burke, G. Zhan, A. Mayer

A cover with capillary barrier effects (CCBE) is being constructed on the AA Leach Pad at the Barrick Goldstrike Mine site near Carlin, Nevada. The purpose of the cover is to eliminate/minimize infiltration of meteoric waters into the leach pad. Laboratory and numerical analyses indicate that Carlin Formation siltstone (TCS), a locally available material, has the necessary hydrologic characteristics when placed on the leach pad to act as a CCBE. A pilot study has been conducted on a small-scale test cover placed on the AA Leach Pad to examine the cover performance under irrigated conditions. The preliminary test results demonstrate that the designed cover is capable of preventing meteoric water infiltration.

Jan 1, 2001

By M. Slatter

The need for anti-corrosion coatings has existed for many years in the ground support industry, but the application requirements have made coating selection limited. Varying groundwater and chemical conditions continually challenge long term coating performance. Traditionally the industry coating preference has been hot-dip galvanizing due to its performance characteristics in highly corrosive environments and low cost nature. However, the galvanized coating has application limitations. This paper highlights some of these limitations and provides selection criteria for a new organic coating developed for one such difficult application, DSI?s Omega BoltPTM Pwhich is an expandable ground support. [ ]

Jan 1, 2009

By R. Switalski, M. Schafer, R. Pintabona, M. Kritzer, B. Lukajic, S. Janosko

Methane gas caused an eight-month shutdown of mining operations at the Mill Creek, Phase 3, Tunnel. The gas-related shutdown occurred as the tunnel was advanced to an approximate distance of 2,700 feet, which constitutes approximately18% of the total tunnel length. The construction of an emergency ventilation shaft, a comprehensive program of de-gassing wells and an expanded gas monitoring system were used to mitigate the gas condition. When complete, this tunnel will be utilized to convey and store combined storm and sanitary sewage collected from a portion of Cleveland, Ohio and ten suburbs. This paper will provide an overview of gas related remedial measures and explain how these measures were integrated into the project to ensure safe tunneling conditions.

Jan 1, 2007

By D. E. Pollock

Recent NIOSH published information has shown an increase of rapidly progressive coal workers? pneumoconiosis (CWP) in the southern Appalachian coal region (SAR) of the U.S., despite the fact that compliance data indicates that most coal miners have been exposed to coal mine dust concentrations below the statutory limit of 2.0 mg/m³. While the exact cause of these elevated CWP levels in the SAR has not been established, several factors may be contributing to the increase in occupational lung disease among coal miners. The mining of high rank coal is known to lead to higher CWP rates, and this type of coal is mined in a portion of this region. Also, a high percentage of the mines in the region are on reduced dust standards because of the high silica content of the airborne dust resulting in miners possibly being exposed to excessive amounts of respirable silica dust. Exposure to excessive amounts of respirable silica dust can lead to silicosis, a disabling and potentially fatal lung disease. NIOSH's Respiratory Hazards Control Branch has been investigating the possible causes that would account for the observed higher trends in disease progression through literature review, data analysis, and in-mine surveying. The investigation to date has revealed that underground mines are faced with cutting large amounts of rock in order to maintain haulage clearances. Cutting rock not only increases the potential for silica exposure, it increases the requirement for machine maintenance which was a concern observed during dust surveys conducted by NIOSH. Over half of the mines operating in the SAR are on reduced standards due to high silica content. Adequate face ventilation of the continuous miner and roof bolter and limited down-wind operations from the miner are also issues of concern and items which require the constant attention of miners operating in these conditions. Disclaimer: Mention of any company or product does not constitute endorsement by the National Institute for Occupational Safety and Health.

Jan 1, 2009

Introduction Aggregate mining impacts on water resources are a source of concern to local governments. To evaluate those impacts, the Minnesota Department of Natural Resources conducted a four-year study at three gravel pits (two alluvial and one beach-ridge) and five quarries (flat-lying Paleozoic limestone). This research provides the first comprehensive look at aggregate mining impacts on ground-water systems in Minnesota. The results will be used by government officials making permitting decisions about aggregate operations and by responsible owners of aggregate mines as they plan their operations to avoid conflicts with neighbors and with resources dependent on ground water and surface water. Natural aggregate (crushed stone, sand, and gravel) is a vital part of our economic infrastructure in Minnesota. Aggregate is used for road and bridge construction and in a variety of building materials. In 2003, the value of construction sand and gravel and crushed stone in Minnesota was approximately $245,000,000. As Minnesota’s economy continues to expand, the demand for aggregate will continue to grow. Sand and gravel pits are located in every county in Minnesota. In 1990, the Minnesota Department of Natural Resources, Division of Minerals (DNR Minerals), estimated the number of active and inactive operations at 1500 with the view that this number was likely too low. Quarries for mining limestone, dolomite, sandstone, and hard rock (granite and quartzite) are found in 34 counties. A 1990 DNR Minerals inventory found 165 active operations, 88 percent of which were limestone quarries (Nelson and others, 1990). That same inventory counted 1,367 inactive operations, 70 percent of which were limestone quarries. Aggregate mining is an extractive use of resources: mining alters the landscape and its natural hydrologic system. When a new pit or quarry is proposed or when an existing operation needs to expand, local governments and citizens typically have many questions about the impacts mining might have. Local governments, which are responsible for reviewing these operations, rarely have the budgets to hire experts to evaluate potential impacts of quarry and gravel pit proposals. The Minnesota Legislature’s Aggregate Resources Task Force identified that local government units (LGUs) often lack the expertise to assess ground-water models (Southwick and others, 2000).

Jan 1, 2007

By Leslie S. Halasz

This paper describes the techniques implemented at Randfontein Estates to develop twin-haulages at 'high speed'. An operation which culminated in the world record advance for twin-end multiblast cyclic development in hard abrasive quartzites. A major expansion project was planned for the mine, with the sinking of a third twin-shaft system (to be known as Cooke No. 3), to raise the level of ore production from 3 500 000 to 5 000 000 tonnes per alumm. Subsequent redesign of the proposed shaft system as a single 9 m brattice wall shaft took place, reducing the planned shaft sinking period by 12 months and saving an estimated R 250 000 (U.S. $ 330 000) in sinking costs. The advancement of the Cooke No. 3 Shaft sinking and development programme necessitated a rapid excavation schedule for two interconnecting twin-haulages from the existing Cooke No. 2 twin shaft complex to provide a second means of egress. An early holing between the two shafts would provide significant financial and technical benefits. Pre-development and equipping of shaft pillar excavations would enable a rapid shaft production build up and blocking out of at least one year's ore-reserves.

Jan 1, 1983

By B. Oraee

Accurate estimation of equipment costs is a key factor in feasibility study and evaluation of design alternatives of mining projects. In this paper, capital and operation costs of backhoe loaders are estimated using multiple linear regression (MLR), based on principle component analysis (PCA). These cost functions are consisted of five independent variables; bucket size, digging depth, dump height, weight and horse power. The MLR is conducted in two steps. At the first correlation between independent variables is omitted using PCA technique. Thereafter, MLR functions are established using selected significant PCs and total cost functions are constituted as functions of initial variables. At the end, accuracy of functions are evaluated using mean absolute error rate method.

Jan 1, 2011

By L. B. Bramlett

The Archean (2.65 b.y.) aged Canning Stock at Copper Mountain, Wyoming contains an average of 20 ppm U. The North Canning and Fuller deposits occur within the enriched interior of the stock. Post-Laramide development of super gene enrichment blankets occurred in wide (25- 100 m) crushed zones. Hematite and chlorite accompany pyrite and sooty pitchblende in the mineralized zones. Reduction mechanisms proposed for deposition of pitchblende are: 1) sulfides, 2) hydrocarbons, 3) bacteria, 4) the water table, or 5) some combination of these. Abundant tar- type organics appear to have preserved the enrichment blankets from degradation. Trace element and radiometric data define target zones, but exploration models focus on favorable structure.

Jan 1, 1980

By Brendan Reilly, Jon Isaacson, Paul McDermott

Kenny/Shea JV is constructing the water intake tunnel for the new Elm Road Generating Station, a supercritical coal-fired power plant in Oak Creek, Wisconsin, being built by Bechtel Power Corporation. The intake tunnel system consists of a temporary mining shaft, pump house and intake channel riser shafts, and four lakebed intake shafts. An 8.33 m diameter, 2,800 m long TBM mined rock tunnel is being constructed to connect the shafts. The intakes are located 2.4 kilometers offshore in Lake Michigan. The shafts and tunnel are being constructed in glacial tills and Silurian Dolomite. The estimated tunnel completion is December 2007.

Jan 1, 2007

The 22nd Annual American Mining Hall of Fame Awards Banquet sponsored by the Mining Foundation of the Southwest will be held at the Westin La Paloma in Tucson, AZ on Saturday, Dec. 4, 2004. This year’s inductee, guest of honor and featured speaker at the banquet will be J. Steven Whisler, chairman and chief executive officer of Phelps Dodge. Whisler is also a director of Phelps Dodge, Burlington Northern Santa Fe, America West Holdings, the National Mining Association, the International Copper Association and the Copper Development Association.

Jan 1, 2004

By C. Stoneback

The attapulgite industry saw a year of solid growth after a weaker 2003. Demand was up between 5 percent and 6 percent driven by almost all of the key markets. Construction continued to show record new housing demand, assisted by continued low interest rates. That drove strong growth in construction related markets like coatings, tape joint compounds and other construction materials applications. The agricultural markets rebounded modestly to increase sales for suspension fertilizers, animal feeds and pesticide carriers. Oil drilling also showed strong growth due to high oil and gas prices. Sales to molecular sieve applications grew due to petrochemical and construction demand. The export markets were assisted by further depreciation of the dollar. The only weak area was in nonagricultural granular sorbents, where other sorbent materials continued to dominate.

Jan 1, 2005

By P. Jurovcik, D. Yantek, D. Ingram

The National Institute for Occupational Safety and Health (NIOSH) identified hearing loss as the most common job-related disease in the United States in its 1996 National Occupational Research Agenda. Previous studies by NIOSH have shown operators of surface drill rigs without cabs are commonly exposed to A-weighted sound levels exceeding 90 dB. During hammer-drilling, A-weighted sound levels exceeding 100 dB were recorded at the operator station. NIOSH collaborated with a local drilling company to design and install a partial cab between the operator and the drill steel in an effort to reduce the sound level at the operator station. Sound level measurements in the field show the partial cab reduces the A-weighted sound level by 5-9 dB at the operator’s left ear and 2-5 dB at the operator’s right ear while hammer-drilling. This paper will briefly discuss the preliminary design of a cab and the testing of materials for construction of the prototype. Explanation of the ideas behind the prototype design and fabrication will be covered. Finally, the field test method and results will be discussed in detail.

Jan 1, 2007

By P. Zhu

The leaching behavior of copper powders recovered from waste printed circuit boards (WPCBs) was investigated using electrogenerated chlorine and aeration in a sulfuric acid solution with added NaCl and CuSO4. Various parameters were studied to understand the mechanism of the copper leaching. When the current density increased from 0 to 0.1 A/cm2, the temperature from 30 to 60° C, agitation speed from 100 to 400 rpm, and the size ranged from below 75 to 150 µm, the leaching ratios of copper powders increased. The leaching kinetics were analyzed using a shrinking core model: 1-(1-X)1/3 = kt, and the leaching process was chemically controlled with an activation energy of 14.7 kJ/mol due to Cl- ion catalysis. The ratios of [Cu+]/[Cu2+] at various temperatures (30, 40, 50, 60 and 70° C) showed a periodic variation with the increasing of the leaching time. The redox potentials of the leaching solution and copper leaching ratios in different conditions were measured. The result indicates that dissolved oxygen achieved the dissolution of coppers and electrogenerated chlorine can promote the dissolution of copper powders and improve the reaction rate of kinetics in the presence of oxygen.

By Yi Luo

Bolting the mine roof is one of the noisiest underground mining operations. The main contribution to the high noise is the drilling of the roof bolt holes, especially in hard rock. A previous research shows that the specific energy consumed in drilling the bolt holes is inversely proportional to the bite depth (i.e., penetration per drill revolution). Less specific energy at a reasonably high bite depth means less energy is wasted in the drilling process to produce heat, bit wear and noise. Therefore, control of drilling operation to achieve a higher bite depth can provide an opportunity to reduce drilling noise from its sources as a proactive noise control approach. In order to explore the feasibility and to develop the proactive technology for reducing drilling noise, drilling tests have been conducted in laboratory settings. The preliminary results show significant reduction in noise dose can be achieved by drilling in medium hard rock at a reasonably high bite depth. This paper presents the findings from the laboratory experimental studies conducted so far.

Jan 1, 2013

By E. Ilgar

Biodegradation of spodumene by Asnergillus niger has been investigated. This organism oxidizes sucrose to citric and oxalic acids (in approximately 50-sot proportions) which degrade the spodumene mineral. The kinetic effects of leach variables on the dissolution of lithium were determined. The maximum theoretically attainable rate of lithium extraction was calculated for the effect of pulp density, to be V : 3.01 x 10 kg m sand the corresponding constant value, K = 12.47% pulp density. The apparent activation energy of lithium extraction vas found to be ^E = 20.3 kJ and frequency factor A = 5.66 x 10 s for S-spodumene leaching by synthetic -3 citric and oxalic acids (each in 0.05 kmol m-3 concentrations).

Jan 1, 1989

By Russel Delmar, Rick Everdell, Harry Charalambu, John Tait

Award of the Design/Build Agreement for construction of Ontario Power Generation’s (OPG’s) Niagara Tunnel Project was made after an intensive 8-month international procurement process. The 14.4-m diameter × 10.4-km long rock tunnel will divert 500 m3/s of water from the Niagara River to the Sir Adam Beck hydroelectric generating complex. The procurement process and Design/Build Agreement included features to address the owner’s requirements regarding risk allocation and cost and schedule certainty, while encouraging innovative ideas from the industry, both technically and commercially. The process included an international expression of interest and prequalification, followed by an invitation for design/build proposals to qualified proponents, and comprehensive proposal evaluations and negotiations with several respondent proponents. An honorarium was provided to the unsuccessful participants in the proposal stage. The resultant negotiated Design/Build Agreement includes Owner’s Mandatory Requirements, negotiated contract terms and conditions, performanceincentive bonuses and liquidated damages for schedule and water delivery performance, a multistaged Geotechnical Baseline Report, joint risk management, references to preexisting community impact agreements and measures to reduce impact on tourism. It also addresses regulatory approvals and permits, an owner controlled insurance policy that required reference to the International Tunneling Insurance Group (ITIG) Code of Practice for Risk Management as a condition of coverage, site specific safety, security and environmental plans, formal team building, a dispute review board, and escrow documentation.

Jan 1, 2007

By Z. T. Bieniawski, E. H. Skinner, R. A. Cummings, F. S. Kendorski

INTRODUCTION Caving Mine Drift Support Design The support of production drifts remains a high-cost item facing the developer or operator of an underground caving mine. Support costs are incurred well in advance of ore production, and there is a strong need to minimize these pre-production commitments of capital. Due to the extensive rock loads that normally develop during the caving process, the support used in caving mines is typically quite heavy and therefore costly. The process of designing this support increasingly makes use of basic tunneling principles, but is hindered by the still-incomplete state of knowledge of rock behavior in caving mines, and high variability of geological conditions in caving orebodies. Caving mines differ from tunnels in that the deformations and rock loads induced are transient and dynamic in occurrence, and are normally large in magnitude, often well in excess of rock mass strength. As opposed to tunnels, caving mine layouts are more intricate, and the methods and effects of construction ordinarily are not as closely monitored. Safety factors in mining tend to be lower and rock masses tend to he weaker. These aspects prevent strict application of tunnel design technology to caving mine drift support, with the result that mine drift supports are commonly designed chiefly on the basis of experience at other mines. Mining procedures at caving mines are evolved in response to site-specific requirements, to the extent that there are really as many caving methods as there are caving mines.

Jan 1, 1983

It is crucial to reestablish a domestic rare earths minerals production industry to help secure the Nation's clean energy future, reduce the U.S. vulnerability to material shortages related to national defense, and to maintain our global technical and economic competitiveness. Given that the Chinese dominance of the rare earths market has adversely impacted supply stability and endangers the United States and its allies' assured access to key materials, rare earths should qualify as materials either strategic or critical to national security. Further, the U.S. government should facilitate the reintroduction of a globally competitive rare earth industry in the U.S. Realization of this objective requires: ? Developing domestic processing capability so that the U.S. is not primarily dependent on China as a source of rare earth ore, and almost exclusively dependent of China for processing of the ores. ? Providing a mechanism where access to Federal lands for rare earth exploration and extraction is possible, and ? Training engineers to design and operate rare earth ore processing facilities

Jan 1, 2011