Search Documents

By Y. Tao

The features of the teeter bed separator and its application in the coarse slime separation of Chengjiao coal preparation plant were discussed. The relationship between the coarse slime separation efficiency by TBS and the particle size were studied, and the influence of using TBS on dense medium consumption and oil consumption were investigated, it increased the clean coal yield and the comprehensive recovery of the whole plant, and brought huge economic benefits to Chengjiao coal preparation plant.

Jan 1, 2011

By G. Van Weert, J. F. Breedveld

Both regular and Silver Impregnated Activated Carbon (SIAC) were studied for their effectiveness in removing WAD (Weak Acid Dissociated) cyanides from solutions at pH = 10. SIAC has already been shown to be effective in the removal of free cyanide down to 30 ppb or less. The present work deals with complexed cyanides. Zinc cyanide was used to represent the WAD component. At pH=10, in either batch or column tests it was not possible to lower the total cyanide in solution from either 30 or 8 ppm to less than 1 ppm, using SIAC, regular activated carbon as received, or after grinding. Silver (metal) impregnation of the carbon was not beneficial in the removal of WAD cyanide. However, when silver is added as silver ions (nitrate), the cyanide is adsorbed as silver cyanide in preference to zinc cyanide. The latter compound converts to zinc (hydr) oxide. This way, the cyanide concentration in solution can be lowered below 1 ppm, even when zinc cyanide is already adsorbed on the carbon used. A single exploratory test with added copper ions indicated a similar effect for that system.

Jan 1, 2004

By ETHAN FUSTER, STEPHEN LEE, Richard Ray

By offering savings in space and capital cost compared to ducted axial and centrifugal fan systems, horizontally mounted jet fans are commonly used worldwide to ventilate vehicular tunnels. They discharge high-velocity jets to transfer momentum to the surrounding airstream to induce longitudinal flow in the same direction as the jet. Vertically mounted jet fans installed in exhaust shafts have been successfully used to ventilate a large passenger rail overbuild in New York City. A comparison of shaft dimensions, vertical placement of the jet fans and measured shaft airflows is presented to evaluate optimum jet fan configurations. Measured shaft airflows are compared to airflows predicted by computational fluid dynamics (CFD) simulations of a three-dimensional model of the overbuild.

Sep 1, 2022

By Julian S. Edwards, C. Frederick C. Pearson, Sevket Durucan

Information gained at the site investigation stage of the Carsington aqueduct project led the designers to suspect that methane might be encountered during tunnelling and therefore gas detection techniques, including emergency shutdown systems, were introduced. After construction, on completion of the excavation and lining of the tunnels, a survey showed that methane was entering the aqueduct dissolved in infiltrating groundwater. General body air concentrations were very low but on closure methane concentrations rose rapidly within the aqueduct. A research project has now been initiated to investigate the mechanism of methane generation and entry rate into the system, the results of which are being taken into account in the preparation of future operating procedures.

Jan 1, 1989

By W. A. Rickelton

The first commercial use of phosphine derivatives as solvent extraction reagents began in the mid 1970's with the construction of several plants to recover uranium from wet process phosphoric acid. The process eventually adopted by all of these plants used the well known trioctylphosphine oxide (TOPO) in synergic combination with D2EHPA to extract U(6+). This prompted the development of other phosphine - based reagents and led to the discovery of a variety of interesting commercial and potential applications which are summarized in this paper. The applications include cobalt-nickel and niobium-tantalum separation and the selective recovery of silver and zinc.

Jan 1, 1994

By D. Forbes

The results of a fundamental study involving zeta-potential and turbidity determinations of solid suspensions are discussed. Illustrations of how these results are utilized to design field applications of solid-grade polymers to clarify mine-drainage water are presented. Operational and economical advantages are examined.

Jan 1, 1997

By D. Mannino, M. Townsend, E. Daniloff, E. Petsonk

Nonspecific airway hyperresponsiveness is a central feature of chronic obstructive pulmonary disease and has been associated with atopy in the presence of environmental exposures such as smoking. Coal miners may develop emphysema and lung function decrements related to their dust exposure. To investigate the roles of airway responsiveness and atopy in these effects, we evaluated the relationships among smoking, a history of hay fever or seasonal rhinitis, and airway responsiveness (AR) in a group of underground bituminous coal miners and nonmining controls. All subjects had a normal baseline percent predicted FEV1. Increased airway responsiveness was defined as a 15% or greater decrease in FEV1 following methacholine inhalation. 85 miners (45%) and 99 controls (46%) were current smokers, 59 miners (31%) and 55 controls (26%) were lifetime nonsmokers; former smokers were excluded from further analysis. Overall, 25% of 144 miners included in this analysis had increased AR, as opposed to 29% of 155 controls. Thirty-seven percent of both miners and controls had a history of seasonal rhinitis. Significantly fewer miners (15%) had a history of hay fever compared to controls (25%, p< 0.05). Figure 1 shows the prevalence of increased airway responsiveness in miners and controls in association with hay fever. In both smoking and non smoking miners the presence of a hay fever history was significantly (p < 0.05) associated with a higher prevalence of increased AR. Little effect was seen in smoking (p = 0.827) and nonsmoking (p = 0.940) controls. Figure 2 shows a similar higher prevalence of increased AR associated with symptoms of seasonal rhinitis in the mining group. This was significant (p < 0.01) only in the smoking miners. No effect was noted in the controls. These data suggest that the association of a history of hay fever or seasonal rhinitis symptoms with increased airway responsiveness may be more common in coal mining, compared to non-dusty occupations. Although the implication of these data are unclear, further study of miners with a history of hay fever or seasonal rhinitis is warranted. (Supported in part by Grants G1135142 and G1105142, US Bureau of Mines, Generic Mineral Technology Center for Respirable Dust)

Jan 1, 1991

By R. J. McGregor

The Internet has revolutionized worldwide communications. Any real or perceived mining incident or environmental spill, no matter how small or remote, can become a disaster of "biblical proportions" through the judicious use of the Internet by environmental and anti-mining groups. In addition, mining companies&apos; own Web sites and unofficial message boards can provide plenty of additional ammunition to the anti-mining forces. This paper explores how the Internet and readily available information are used by anti-mining groups active on the Web.

Jan 1, 2001

By B. Salopek, D. Rajkovic, D. Rumenjak

Among other types of sustainability indicators, linguistic variables have been proposed. During the past few years considerable effort for using the fuzzy logic and linguistic variables (LVs) in environmental decision-making for the mineral industry has been made. The linguistic variables defined could, among others properties, describe the property of acceptability for environment for various environmental indicators. Some proposals for construction of such variables are based on administrative decisions from environmental impact assessment procedures for mining, which provide information for acceptability of quality kind for environment (e.g. obtained from public participation, experts, environmental administration). The measures of evidence for construction have to be based on sets (not only on the members of sets). The administrative decisions with their statements and explanations could be considered as such sets. The measures of evidence appropriate are plausibility and belief measures. Using the more elaborated methods from the theory of evidence, the better estimation of those measures could be achieved. The methods of constructing the linguistic variables, previously suggested and based on obtained measures, are also discussed.

Jan 1, 2011

By R. K. Davey

Subsequent to the determination of an ultimate pit and ore reserves for metallic and nonmetallic deposits, it is necessary to develop the most profitable long-range mining sequence for the deposit. Long-range planning is a dynamic process because product prices and costs change, additional assay and metallurgical data become available, mining technology and operating prices and requirements change. The three case studies included in this subsection present different techniques for dealing with the objectives of long-range planning. To be able to forecast production, profitability, and capital requirements, it is essential to have a long-range mining plan.

Jan 1, 1979

By Serguei A. Diatchkov

The principles of classification of reserves and resources in the Soviet Union were developed in 1960. Mineral reserve calculations were reviewed by the State Committee on Reserves for approval, then registered in the State List of Mineral Deposits and included in the State Balance of the Reserves. In 1981, however, a new "System of Classification of Reserves and Resources of Mineral Deposits" was adopted. This classification system (Table 1) is still used today in the Commonwealth of Independent States (CIS). It subdivides mineral concentrations into seven categories in three major groups, based on the level of exploration performed: explored reserves (A, B, C,), evaluated reserves (C) and prognostic resources (P1, P2, P3). Explored reserves Explored reserves are calculated within exploration contours. Category A The A category is the highest level of classification for any given mineral deposit and requires comprehensive exploration. First, the ore body&apos;s position, shape and structure must be accurately delineated (Fig. 1). Next, the mineralogy of the ore body must be studied to determine its composition and properties as well as the distribution of both ore and detrimental components. It is also necessary to outline the blocks of barren rocks and limits of subeconomic ores and to distinguish between the different types, grades and physical-chemical properties (mineral texture and structure) of the ore, the

Jan 1, 1994

By Gösta W. Diehl

During the past five years the use of all-hydraulic drilling equipment has increased rapidly, and we have now reached a point where the hydraulic drill has become an alternative to be seriously considered for every drilling operation. The hydraulic drills have many advantages over pneumatic drills, but they also have certain characteristics, which makes a potential user hesitate before making the switch. And when the decision to use hydraulic drills has been made, the user then faces another choice of equal difficulty: the choice between different hydraulic systems. This paper discusses some of the factors to be taken into account when considering hydraulic drilling equipment for rapid tunneling in hard to medium hard rock. THE CHOICE BETWEEN HYDRAULIC AND PNEUMATIC EQUIPMENT The choice between a hydraulic and a pneumatic drill is much more than just that: It is a choice between two different systems. The choice is usually based on the productivity, economy or ergonomy of the system. However, also other factors should be considered, such as service capabilities and training requirements. And finally the choice will be influenced by the need to acquire know-how in the new technology. Productivity If the prime consideration is to achieve the highest possible tunneling speed, then the high penetration rates of the hydraulic

Jan 1, 1979

By Jon A. Hummer, MICHAEL R. SHAHAN, Aleksandar D. Bugarski, Shawn Vanderslice

Occupational exposures to respirable dust and submicrometer aerosols emitted by diesel-powered equipment are a health concern for underground mining operators and regulators. A study was conducted in an underground mine with the objective to identify, characterize and source apportion airborne aerosols at the setup face and recovery room during longwall move operations. 

By T. Klemetti, W. H. Su, M. A. Van Dyke

Entry stability in coal mines is dependent on geologic conditions and engineering controls. Most engineering controls in ground control are predictable and standardized for typical geologic conditions. However, geologic anomalies may exist that are difficult to detect with traditional core hole drilling. Borescopes offer a cost-efficient way to gather more geologic data between core holes. Additional data obtained from borescope results provide a clearer picture to enhance detection of hazardous conditions due to geologic anomalies. The equipment, methods, and analysis of borescope results provide geomechanical engineers with a clear understanding of strata behavior and the best information to implement roof control plans and supplemental support to enhance miner safety and health. INTRODUCTION Borescope technology has changed very little since its inception. However, the idea to use borescopes to examine roof strata started with the U.S. Bureau of Mines in 1979 with the production of a fiber-optic borescope (FitzSimmons, et al., 1979). The first documented use of a borescope in the coal mining industry began during the 1980s in Australia by researcher John Shepherd. Shepherd’s idea was to use a borescope to collect a series of data points from the roof lithology and compose a geologic cross section. The cross section was then used to identify key features that suggested the beginnings of roof failure. The features Shepherd identified were bedding plane separations in the roof and low angle, extension, and tensile failures. Shepherd also suggested that the borescope findings could be used for geologic mapping for lithological variation, fracture distribution, and determining if supplemental roof support was needed (Shepherd, et al., 1986). In the United States the first publication about borescope usage for coal mine stability assessment was by Su and associates in 1999, who specifically related the combination of using borescope, geophysical, and corehole data to produce geologic hazard maps (Su et al., 1999). This work directly linked the usage of a borescope with the design of supplemental roof support. The use of borescopes in mining was adopted industry wide by the 2000s. Operator case studies were being published using borescopes to aid in supplemental support recommendations and hazard mapping. An Australian study published in 2007 based the optimization of secondary support after each longwall pass on the results of borescope data. The study stated that the borescope was an invaluable tool for understanding roof behavior (Black, et al., 2007). In 2009, a publication by the National Institute for Occupational Safety and Health (NIOSH) took the concept of borescoping one step further. The work centered around creating a roof quality index (RQI) for limestone mines based on borescope data. The RQI attempted to assign a ranking to establish the nature of the roof and its stability (Ellenberger 2009). In theory, this would have been a very useful tool, but the RQI system has not been widely adopted in the industry.

Jan 1, 2019

By R. N. Torbin

The degree to which automation, remote control and robotics have been used in the mining industry is far less compared to general industry. Reasons include the adverse working environment, the difficult work operations and the generally lower incentive for capital investments in new mining equipment. The author and his employer has been involved in the development of advanced mining and underground construction equipment. This equipment is designed to he remotely operated, to improve both productivity and worker safety. Many of these machines employ advanced electronics and robotic features. The types of machines that will be discussed include remote shaft lining and placement, remote excavation and mining operations, and automated conveyor systems.

Jan 1, 1991

By Dalva L. Moellenberg

Introduction Hard rock mine closure (often referred to as decommissioning), mined land reclamation and financial assurance requirements are receiving considerable attention by governments and organizations around the world. In the United States, federal agencies and the states continue to consider and make changes to laws governing mine closure and mined land reclamation, most of which were originally enacted in the mid-1970’s through the mid-1990’s. Internationally, a number of prominent groups and various countries currently are considering new laws, regulations and policies for mined land reclamation. For example, the European Union has conducted a review of existing European laws concerning mining wastes and mine water and is considering new directives concerning mine waste and mine water management and liability schemes that are likely to significantly impact mine closure and mined land reclamation. Many countries, particularly those outside of North America, Europe, and Australia, have recently adopted or are considering new mine closure and reclamation legislation and regulations. These include significant hard-rock mining countries such as Chile, Peru and South Africa. This paper identifies recent developments in hard-rock mine closure and mined land reclamation laws in the United States, focusing on several of the more significant and controversial developments. It also discusses some of the more significant international efforts to consider mine closure and mined land reclamation laws and policies and some of the notable conclusions and trends from those efforts. The focal issues discussed in this paper include requirements for the reclamation of open pit mines, including backfilling; consideration of and measures to address the mining of sulfide ores and potential for acid mine drainage; and new requirements for the estimation of closure and reclamation costs and for financial assurance for closure and reclamation.

Jan 1, 2005

By K. Bommer

"In today’s fast paced, globally competitive world, reliability and machine uptime are of the utmost importance to a successful operation. Along with these targets more emphasis is being put on cost reduction and decreasing the environmental impact of the overall system. To achieve these goals, automatic lubricators and lubrication systems have been used in many industries for years and are now becoming a common tool in the mining industry as well. These systems are able to provide proper lubrication amounts at the proper times autonomously, helping to keep the machines running smoothly while minimizing the physical support required. Copper mines in the southwest have begun utilizing auto lubrication to avoid mistakes and unplanned shut downs on critical equipment. This paper will describe the engineering behind these products and review case histories where these tools have been successfully utilized in the mining industry. INTRODUCTION In a dirty, dusty, wet environment, where machine uptime is imperative, proper lubrication of bearings is the only way to survive. With the push for cost reduction and mines striving to lower their environmental impact and increase worker safety according to MSHA guidelines, the old lubrication practices have come under scrutiny. It is no longer encouraged or cost effective to have maintenance personal walk from point to point throughout the entire mine pumping a shot of grease into each bearing once per shift. Automatic lubricators and lubrication systems have been on the market for years but recently, as the market focus has changed and technology has developed, the use of these systems has begun to rise in the mining industry. Automatic lubrication systems can be as simple as a single point lubricator lubricating one (1) bearing or a more complex system lubricating numerous bearings. With system design, the automatic lubricator provides a preset amount of grease to a bearing at regular, predetermined intervals. The systems designed to lubricate more than one bearing contain grease pumps of some design and possibly PLC controllers which can be used to remotely adjust and monitor the system. As can be seen in Figure 1, the right amount of lubrication can be achieved much more reliably with automatic lubricators. Depending on application needs, the market now has products to fit almost every wish list. This paper is going to focus on the single point systems that are lower in cost but are still being effective."

Jan 1, 2015

By J. Willison

Over the past decade, the coal mining industry has faced the difficult task of remaining profitable in the midst of declining market prices. Historically, the industry has been quite capable of meeting this challenge by various means. As total costs to mine and market coal continue to increase, new methods of tackling the problem must be implemented. Studies have shown that although many options exist to influence both inby and outby costs, the greatest potential remains in addressing costs at the coal face. Mining operations can positively effect a change in their profitability by either reducing costs, or by increasing production to in turn lower their net cost per man-hour. Original equipment manufacturers can play a key role in both options through the introduction of new technology that permits higher extraction rates, as well as other advantages leading to lower cost coal. A leading advancement over the past 30 – 40 year period has been the advent of progressively higher voltages to operate the mining equipment. This advance enables higher power transmission for a given cable size, operation at lower amperages resulting in less voltage fluctuation, and reduced heat on the cable and electrical components.

Jan 1, 2003

By James P. Dorian

In 1990, the former Soviet Union ranked first worldwide in the production of asbestos, chromium, iron ore, iron and steel, lime, manganese, mercury, nickel, peat, potash, and titanium. Since the middle of this century, that nation had maintained one of the world&apos;s most valuable mineral industries, ranking number two in 1950 and number one in 1990. It is clearly an enormous mining industry, with more than 1300 enterprises and an estimated employment base of 1.2 million persons (Table 1). Despite its size and historical achievements, however, the mining industry of the 1990s in the former Soviet republics is encountering problems in performance, efficiency, transportation and utilization. The industry operates below full capacity and is plagued by outdated technology and equipment, rising production costs, capital shortages and labor strikes, in addition to general economic deterioration and civil unrest. Attempts to boost domestic minerals supply in the republics so far have failed because of economic difficulties. And the republics lack the financing required to initiate new, large-scale development projects.

Jan 1, 1992

By Hayward B. Oblad, Anthony G. Fonseca

Coal flotation has been practiced since about 1920 in Europe and since about 1926 in the U.S. Over 200 U.S. coal preparation plants now use the process to recover coal. Over the 60 year period, the fundamental principles upon which flotation is based have been enumerated, but the interaction between the parameters that affect flotation has not been quantified and a useful model which accounts for these parameters has not yet been developed. A comprehensive and user friendly kinetic model coupled with better process monitoring and control instrumentation would allow plant operating personnel to better predict flotation performance and better control the flotation process in coal preparation plants.

Jan 1, 1989