Search Documents

By E. Watkins, V. Gangrade

Large-opening stone mines often rely on natural ventilation and a network of auxiliary fans to produce adequate ventilation conditions in the mine instead of main mine fans, which are commonly utilized in coal mines. Large air volumes in underground stone mines, poor ventilation practices, and low operating budgets for mine ventilation potentially increase mine workers’ risk for dust, silica, and diesel particulate matter (DPM) emissions exposure. To help improve mine ventilation practices, the optimal auxiliary fan location for maximum airflow production from a ventilated intersection was determined using a combination of field measurements and computational fluid dynamics (CFD) modeling. In this study, conducted by researchers at the National Institute for Occupational Safety and Health (NIOSH), airflow quantity and fan data were collected at a partner mine to be applied as CFD model input parameters and comparison data for model validation. A six-foot diameter auxiliary propeller fan was introduced into the validated CFD model at three locations at a mine entry intersection with established ventilation flow perpendicular to the fan direction. Placing the fan on the opposite side of the intersection from the target active face area produced the highest ventilation flow rates at the downstream locations tested and produced the lowest amount of air re-circulation. The findings show that optimizing the placement of an auxiliary fan may increase the net effective ventilation flow rate by 70,000 cfm and reduce recirculation by 26%, which maximizes the potential effectiveness of large-opening stone mine ventilation systems and decreases mine worker exposures to airborne contaminants.

Mar 2, 2022

By Huo Zuzhao

The main feature of caving methods is to draw ore from the overlying waste rock. Research on the movements of ore and waste plays a very important part in reducing ore loss and dilution and raising the economic benefits. This paper gives the basic theory of computer simulation of ore-draw, exposses the physical significance of mathematical model, puts forword a new formula of similarity characteristic value, brings forth a method of adjusting similarity, introduces the major functions of the simulation program and describes the ore draw control and stope parameter selection through computer simulation.

Jan 1, 1986

Federal Regulations require that coal producers conduct a written, in-house investigation with every lost time injury accident. Besides their obvious value in accident prevention, competently conducted investigations can provide a number of additional benefits to include positive supervisor involvement, the control of rising worker's compensation costs and a measure of protection from civil/criminal proceedings. The paper describes such topics as MSHA minimum requirements, investigator selection and training, accident site procedures, witness interview techniques and the management review process. The reader is also presented with a number of information resources available through MSHA, the National Safety Council and other sources.

Jan 1, 1995

By G. M. Wilemon, J. G. Davis, R. G. Swanton, B. J. Scheiner

The US Bureau of Mines has conducted investigations on extracting phosphate values from wastes generated during the mining and beneficiation of phosphate matrix. These wastes may contain up to one third of the phosphate originally present in untreated ore. Samples of wastes were air-dried and leached using 93% sulfuric acid in the presence of methanol. Evidence for the formation of a calcium sulfate hemihydrate coating that hinders complete dissolution of phosphate is presented. Solid-liquid separations were enhanced when flocculation was effected using poly(ethylene oxide) (PEO) in conjunction with hydroxypropyl cellulose (HPC) or hydroxyethyl cellulose (HEC). A conceptual flowsheet for a proposed process using an acid-alcohol leaching technique is presented.

Jan 1, 1991

By G. A. Eltringham

Mining and extraction methods in the copper industry use basic technologies developed over a period of almost 150 years. Paradigm shifts in the industry have been rare, yet human involvement in the activities has changed dramatically. Clearly defined extraction paths have become more blurred as economic considerations broke down the barriers that had encouraged specialization. What had been a labor-intensive industry unfettered by environmental restrictions was forced to change. Better productivity and "cleaner" operations resulted in much higher capital costs on a plant basis. Many of the changes were truly innovative in the same spirit as in the mining revolution of the first decade of the twentieth century. What role will innovation play in the next 20 years as lower-grade, mixed-metal orebodies are exploited in more remote locations?

Jan 1, 1998

By P. R. Altringer, R. H. Lien, B. E. Dinsdale

The Bureau of Mines, U.S. Department of the Interior, is investigating biodegradation of cyanide as a means of decommissioning heap leach operations. Biological oxidation decreased weak acid dissociable (WAD) cyanide in process solutions from 50 to 170 ppm down to 0.1 ppm. The tests were conducted both in trickling column reactors, using quartz as the growth surface, and in upflow columns, using activated carbon as the growth surface. In addition, exploratory tests indicated that bacteria will destroy residual cyanide in leached ore. A flowsheet has been proposed for closure of heap leach operations in which the metals processing portion of the plant, possibly the carbon adsorption columns, or a collection pond is used as a bioreactor. The cyanide in the process solution is destroyed in the bioreactor and the treated water is used to rinse residual cyanide from the spent heaps. The water is recycled until the effluent WAD cyanide concentratio� meets discharge standards.

Jan 1, 1992

By H. Colijn

The ever increasing price of bulk commodities forces buyers and sellers in world markets to take a more careful look at methods for obtain¬ing accurate accounting of commodity trans¬actions in commerce and material utilization in processes. Depending upon the application of a sampling and weighing system or the use intended, inaccuracies can result in an eco¬nomic loss of income or a loss in quality of the process. It inevitably results in a loss of control of ones costs. The accuracy of samp¬ling and weighing systems is today extremely important, as they are recognized to be the key components of the overall management system designed to provide both quantitative and qualitative control. This paper will be confined to the weighing systems only and will deal with various as¬pects of system design, calibration and opera¬tions. Special emphasis will be placed on new developments and requirements in this field.

Jan 1, 1988

By Carlo Sampaio, Moacir Veras, Aaron Young, Carlo Petter

"Three major challenges for the mining industry are the minimization of energy use, water consumption and environmental impact. Therefore, any technique that reduces milling waste, decreases water usage and shrinks impact during mine life must be considered a major innovation in mining.To these ends, one of the most impactful developments in mining within the last 10 years has been the expanded use of high technology sensors to create preconcentrations of mine ore (Jönsson, 2014). The most common sensors used are charge-coupled device (CCD) cameras, that allow through a red, green and blue (RGB) coloring system, the separation of minerals with different colors, tones and, in many cases, with differences in brightness.More recently, the development and use of dual energy X-ray transmission (DE-XRT) to enable the separation by atomic density of the constituent minerals within a given rock has become a reality. Within this work, a rapid bibliographical review of the CCD and DE-XRT methods and examples of their usage within mining and the industrial minerals sector are presented.Sensor-based sorting in miningAutomation within mining is one of the industry’s current goals. Sensors of various kinds have been used as steps toward automation in recent years, from improving the safety and productivity of haul trucks through the use of cameras and global positioning satellites (GPS), to the divination of slope failures. Just as with other mining areas, sorting has improved dramatically and made great steps toward automation in recent years (Wotruba et al., 2014).Sensor-based sorting (SBS) uses spectromatic sensors to identify intrinsic characteristics of particles and separates them by either mechanical or pneumatic means into different product streams (Wotruba et al., 2014). SBS can be used with great effectiveness to improve gravimetric beneficiation through the selective separation or preconcentration of run of mine ores (ROM)."

Jan 1, 2015

By A. De Daio, D. W. Fuerstenau, P. C. Kapur

Because of its pronounced tendency to undergo visco-plastic flow, coal ground in the energy- efficient high-pressure roll mill invariably comes out as a briquetted product which must be disintegrated in a conventional type of grinding device such as the ball mill. The aggregates comprise comminuted coal particles that are apparently extensively cracked and weakened during passage of the coal through the high-pressure rolls. Their deaggregation in a ball mill in the second stage is accompanied by further grinding of the coal with a relatively small expenditure of energy. Thus in spite of energy dissipation in briquetting in the roll mill and in disintegrating the briquettes in the ball mill, significant energy savings are possible in the fine grinding of coal in a two-stage serial grinding mode, as compared to ball mill grinding alone. It has been determined that for the best results the energy invested in the two grinding stages must be apportioned in an optimal manner, the energy consumption in the ball milling step is comparable to, even in excess of, the energy spent in the high- pressure roll mill; and 20 to 50 percent energy savings might be possible in grinding coal to minus 200-mesh size by this two-step process, as compared to conventional milling.

Jan 1, 1995

By J. A. M. Cano

A brief introduction is made on the existence of sulphides in the top gas of the Midrex Shaft Furnace, giving consideration to the operation of the furnace and the liberation of sulphur as well as its consequential effects on the reduction process. The text shows a study of sulphur distribution in the pellet, emphasizing the importance of this distribution in relation to the liberation of sulphur during the reduction. A study was made to determine the sulphur compounds that exist in the pellets, showing ways of controlling the sulphur distribution and reducing its liberation?during the reduction.

Jan 1, 1989

By Michael N. Allenby

One of the least discussed areas in the ever-improving technologies of gold recovery from ore bodies and tailings is the chemistry of the waters used in the plants. Carbon-in­ pulp, carbon-in-leach, heap/dump leaching and iological oxidation processes are all affected by water quality. The remoteness of a lot of the plants means that the large water requirements can often only be met by a ground water source. The chemistry of waters from different sources poses different problems, but generally a lot of these waters are scale forming. Scale-forming tendencies can be described by calcium, magnesium, barium and strontium assays. They can be notated by Langelier and Ryznar indices. They can be plotted by computer programmes that print out scaling indices at different conditions. The propensity to scale can -be readily determined. The prevention of scaling -or at worst minimisation of scaling -is the ambition of the suppliers of scale inhibition programmes. This prevention/minimisation technology is discussed below.

Jan 1, 1993

Mines in the Lake Macquarie region of New South Wales, Australia, are faced with the dilemma of having to introduce longwall mining techniques at a time when increasingly large areas of the surface are being used for urban development. Increasing pressures on safety, costs and productivity performance dictate that longwall mining is the method for the future. Construction of surface structures is controlled by a statutory body known as the Mine Subsidence Board (MSB). All surface structures have to be designed to MSB criteria. All mining plans involving secondary excavation also have to be submitted to the MSB for approval. The Board acts as risk assessor in evaluating acceptable levels of surface subsidence vs. the value of the coal resource. Surface repairs are paid for by a levy on all coal producers.

Jan 1, 1995

By P. E. Snoek, R. L. Gandhi, C. S. Miller

Slurry operations are an integral part of mineral processing. There is therefore reason to consider using slurry pipelines for long distance mineral transportation. This paper reviews the current state-of-the art of such systems and, in particular, the design factors which must be addressed. It also discusses the selection of major components such as pipe, pumps, valves and storage facilities. Finally, the major steps required to determine the economic feasibility of a slurry system are listed and the major advantages and disadvantages of slurry pipelines compared with other forms of land transport are summarized. SLURRY PIPELINES: GENERAL OVERVIEW Minerals Transported Long distance slurry pipelines have been successfully used for transporting coal, iron concentrate, copper concentrate, limestone and phosphate. Additionally, several tailings disposal pipelines of considerable size and length have been built, but these generally are not categorized as long distance commercial mineral transportation systems. Table 1 lists selected examples of commercial slurry pipelines.

Jan 1, 1986

By E. S. Bianchin

The more complex control needs of today's mineral processing plants combined with ever-changing digital technology have brought numerous improvements to process control systems. This paper discusses recent advancements in distributed control systems (DCS) which facilitate the implementation of process plant automation. Some of the topics of discussion include integrated function controllers, weigh scale and analyzer interfacing, operator interfacing, personal computers, process information management and process plant management.

Jan 1, 1988

By L. C. de Kooker, K. Esmaeili, I. Musonda, M. Ferentinou

This paper presents the results of an investigation into the effect of pore pressure regime on the factor of safety (FS) and the anticipated critical failure mechanism for a fly ash storage facility. In this study, pore pressure measurements from standpipe piezometers and pore pressure estimated from seepage analysis were used for a comparison of the estimated FS for a fly ash slope. This comparison was applied for static and seismic scenarios. To account for the uncertainties resulting from the limited data available and support a qualitative risk assessment evaluation, a probabilistic analysis was performed. The slope stability analysis was conducted in 2D and 3D, adopting the limit equilibrium analysis approach, and a finite element seepage analysis. The results suggest consistency of failure surfaces for 2D and 3D and an increase in FS values of 5 percent for the 3D approach, limitations of standpipe piezometers. The study demonstrated the sensitivity of the FS value, and the implication of adopting representative material properties, and water table levels, especially in cases where limited data are available, and assumptions need to be made to assess the long-term stability of a fly ash dam facility.

Aug 1, 2024

By R. Tamir

This paper will describe the benefits of utilizing the decision support system, DSS to support the methodology of structured decision-making in the mining environment. It will outline the layers of the mining related decision making – 1. Creation of “one truth” situational awareness utilizing 2. existing planning, ERP, operational and monitoring agents, a. Expressing plan verse performance across mining phases and functions compared with the actual and trends to evaluate performance. b. Creating alternate courses of action and the implications up and downstream. 3. It will review the current condition were although a multitude of technologies resolve multi variable issues they do not interact in a way that assists decision makers throughout the organization in making high-quality decisions that will push the overall performance envelope. 4. The paper will show the benefits of integrating military methodologies to resolve multi variable complexed issues (operational, financial and other), operating in changing environments in order to meet time sensitive objectives with restricted resources. This is achieved by creating a shared situational awareness thru incorporating information from a multitude of data generating agents, creating COA, selecting the appropriate and turning it into a plan. The paper will discuss the implementation and suggest a path.

Feb 1, 2023

By Ralph E. Weeks

Utilization of true in situ technologies for mining copper in Arizona will involve a complex environmental permitting process. This process is a key factor in determining the feasibility, costs, and implementing time frames required for development of this innovative mining method. The regulatory structure in Arizona is presently changing due to enactment of the Environmental Quality Act (EQA) of 1986 and development of new aquifer protection rules and regulations. The Bureau of Mines has reviewed the comprehensive hydrogeologic characterization, ground water monitoring, mechanical integrity testing, well construction, contingency planning, and other regulatory elements that will serve as mechanisms to assure protection of ground water resources. The purpose of this paper is to inform the domestic copper industry of the significance of the new Arizona regulatory structure and its implications for prospective in situ operators.

Jan 1, 1988

By S. P. Brown, J. E. Worthington

Increasingly, exploration geology seems to be growing into a practice overly separated from production geology, yet the eventual purpose of exploration is a producing mine. To help in the search for new deposits, exploration "lessons" will be drawn from the papers given at the Fall AIME Applied Geology Symposium. In addition, examples will be re-emphasized to show how early observation of matters now routine to mine work (for example, hydrology, rock mechanics, oxidation state) can help increase the effectiveness of exploration.

Jan 1, 1992

By Dennis K. Mortensen

Improvements in metallurgical performance are continually being made in the attempt to achieve the metallurgist's goal of maximum concentration, minimal loss of recovery and at costs that maximize profit margins. Innovative technological advances provide a means for the metallurgist to more thoroughly understand the mechanisms of separation and foster new ideas from old. Problems associated with the implementation of new technology can be overcome effectively if the metallurgist thoroughly understands the metallurgical systems with which he is working.

Jan 1, 1991

By T. Ertekin, R. V. Ramani, W. Sung

The emission of methane in the coal mine working faces has two immediate impacts with regard to coal mine planning. Firstly, at the planning stage, the coal mine ventilation system must be designed such that airflows in the faces keep the concentrations of the gas in faces areas to below one percent. If the concentrations were greater than one percent, the production machine has to be shut down resulting in a loss of productive time. In an extreme case, concentration can reach explosibility limits which may lead to ignitions and explosions. Secondly, in excessively gassy coal seams, several alternatives can be applied to the mine layout configuration, and the mining method to be predicted for the extraction of coal, so as to insure a productive and safe operation. In this study a two-phase, two-dimensional finite-difference model was used to predict the methane emission rates into active mine working area under several methane drainage schemes. The numerical model utilizes a recently developed multi-mechanistic flow theory which describes the flow of methane in an heterogeneous and anisotropic coal seam. Transport of methane in the micropore structure of the coal is described by the Fick's law of dif- fusion under the influence of existing concentration gradient, while flow in the more permeable butt and face cleats (macropore spaces) is formulated by Dar- cy's law under the influence of existing pressure gradient. The desorption of the methane is accounted with the aid of a quasi-steady kinetic sorption model. A series of simulation studies were conducted in a systematic manner by sifting through the parameters associated with the coal seam characteristics and the degasification strategies in order to understand those which most significantly affect the methane emission rates in the face areas during mining. Along these lines, the effects of coal seam properties such as thickness, porosity, permeability, sorption characteristics and scheduling of drainage process against the mining operation have been isolated to understand the role of each individual parameter on the methane emission rates.

Jan 1, 1987