Search Documents

By N. Prenn

"INTRODUCTION The 2014 SME Guide for Reporting Exploration Results, Mineral Resources, and Mineral Reserves (the SME Guide) has been adopted by the Society for Mining, Metallurgy, and Exploration, Inc. (SME). The SME Guide is recommended as a minimum standard and a basis for developing industry best practices in the classification of Mineral Resources and Mineral Reserves for public and private purposes. The Guide is therefore strongly recommended to be used by members of this organization. The SME Guide was updated in 2014 to include CRIRSCO (Committee for Mineral Reserve International Standards) core definitions, and it is envisioned that the U. S. Securities and Exchange Commission (SEC) will adopt the SME Guide in 2016. However, as of the end of 2015, the SEC Industry Guide 7 remains the standard for the U.S. reporting of Mineral Reserves. This paper will cover the classification of Mineral Resources and Reserves, a discussion of Modifying Factors, and the classification definitions and guidelines. The definitions and guidelines contained in this report are from the SME Guide. FRAMEWORK FOR MINERAL RESOURCE AND MINERAL RESERVE CLASSIFICATION Figure 1 illustrates the classification of Mineral Resources and Mineral Reserves using the Guide. Mineral Resources are divided into three classifications of Inferred, Indicated, or Measured while Mineral Reserves include Probable and Proven classifications. These classifications reflect improved knowledge and confidence of the deposit from the top of the figure to the bottom. In other terms, the deposit risk also decreases from top to bottom.The relationships in Figure 1 reflect different levels of geoscientific knowledge and different degrees of technical and economic evaluation. Mineral Resources can be estimated on the basis of geoscientific information with input from other disciplines to establish reasonable prospects for eventual economic extraction. It was not too many years ago that the classification of a Mineral Resource was based on the evaluation of a limited set of factors that included spatial drill hole and grade distribution (kriging variance, as example), distance to the closest hole, and number of samples used to estimate a block grade. These are still important considerations, but classification following the Guide must also take into account sample integrity, sample QAQC, database integrity and completeness, geological understanding, and geological and grade or quality continuity. In addition, a general consideration of the Modifying Factors, to establish reasonable prospects for eventual economic extraction, adds complexity to the classification."

Jan 1, 2016

By Jorge Gutierrez C.

CODELCO-CHILE, the world's largest copper producer, began an integrated study of the informatics situation in the corporation at the end of 1980. As a result, a five years strategic Systems Plan was elaborated and approved by top Corporate management. Main points in this plan were: a systems architecture with information integration to the top level management; a higher degree of information technology in the production areas, an optional systems development resources utilization and a high profitability of the plan itself. During the study phase a series of theoretical definitions were fixed and used as a basis for the plan's design. A "common systems" approach was chosen as the development strategy instead of corporate systems or separate divisional efforts. Top management should be highly involved in the revisions of the plan, as well as qualified users should be chosen as project managers. The systems architecture should grant the information integration to the corporate level, in order to support an integrated planning and administration environment for the corporation. A total of 15 projects were defined, involving 570,000 man-hours and shifting the development efforts towards the production and production services areas. The paper presents a critical evaluation of the whole process, showing its good and bad aspects and a positive global balance. It also points some suggestions and hints to any corporation who wishes to get involved in a similar experience.

Jan 1, 1989

By J. H. Bassarear, J. D. Vincent

General. Copper, the first metal used by man, today is the third in consumption after iron and aluminum. Compared to these it is relatively rare, with less than 0.01% of the earth's crust copper, 8% aluminum, and 5% iron. Nevertheless. our modern civilization is heavily dependent upon copper because of its high conductivity and resistance to corrosion, ease of working, durability, wide range of properties by virtue of its readiness to form alloys with other metals, and its attractive colors and texture that make it so desirable for many crafts and arts. These attributes explain why copper is chosen for a long list of uses, including electrical wiring, switchgear, and bus bars; piping, roofing, and siding; and manufactures of brass, bronze, and other alloys. The fact that copper ore is mined in nearly all parts of the world is significant. Its importance is shown in Table I, which gives figures on world production from 1968 to 1977. In the Free World, North and South America and Africa are preeminent. The table also shows the generally upward trend of production in this period; accurate figures for 1978 and 1979 from the same source are not yet available (1980), but it is certain that major environmental, economical, and political factors continued to disturb the industry in those years and into 1980.

Jan 1, 1985

By M. Westendorf, T. Banerjee, S. Kaushik, D. Tinney

"The Copper Mountain Mine is located in Princeton British Columbia, Canada and produces 80 – 90 million pounds of copper annually, as well as gold and silver by-products. The ore processing plant has a conventional SAG/ball mill circuit with inline pebble crushing, followed by flotation. At most plants, much time is spent evaluating and optimizing the comminution and flotation circuits. The cyclones are a key contributor to the effective operation of the plant: They define the circulating load in the comminution circuit and provide the classification that ensures liberated material is passed through to flotation. If the cyclones are not performing as they should, the results are often a combination of lost recovery, grade, capacity and reduced throughput in flotation. For such an impactful unit operation, cyclones have historically been under-instrumented. Consider as well that the cyclones are typically located at the highest elevation in a plant, and it becomes clear why they often underperform. Copper Mountain Mine recognized the critical role that cyclones filled in their plant and worked to optimize their operation through the implementation of a Portage Cyclone Detection (PCD) system to identify plugging and roping incidents, Portage Pumpbox Control (PPC) to manage the flow to the cyclones, and AwaRE to control the grinding circuit. As a result, cyclones overflow stability has increased, switching out a roped or plugged cyclone now happens within seconds rather than many minutes, and both the grinding and flotation circuits perform better. INTRODUCTION Cyclones are one of the most extensively used pieces of equipment within the mineral processing industry because of their simplistic operating and maintenance philosophies. The cyclones are commonly used as classifiers within the comminution circuit to control the grinding product particle size for satisfactory performance of downstream operations. The cyclones are a key contributor to the effective operation of the plant and have a significant impact on the mineral processing plant operations. If the cyclones are not performing as they should, the results are often a combination of lost recovery, grade, capacity and reduced throughput. Similarly, an inefficient cyclone operation may also lead to low or high recirculating loads that impact the efficiency of the comminution circuit. This highlights the importance to have proper stability in cyclone operation while implementing any plant-wide optimisation strategy."

Jan 1, 2015

By C. D. Wittreich

The results of an engineering study of fiber-reinforced cemented tailings are presented. These tests were conducted to evaluate the potential for using fibers to increase the strength of cemented tailings used as backfill for ground support in the undercut -and - fill mining method in a mine subject to high horizontal stresses and rock bursts. Stress-strain measurements indicate that fibers not only increase the peak compressive tensile and flexural strengths of cemented tailings, but limit reductions in residual strength following failure. Results also show the effect of water content, fiber type, fiber density, and curing time on strength.

Jan 1, 1987

By C. Sunderman, R. Jacksha

"Mine monitoring through various sensors is a vital component of successful miner safety and health programs. Data from environmental, geotechnical, infrastructure and other types of sensors are increasingly used to discover and mitigate health and safety concerns in underground mines. In many smaller underground mines, as well as in the new development headings of larger underground mines, leaky feeder communication systems may be the only available means to transport crucial monitoring data. In addition, data transport is increasingly being delivered using Internet Protocol (IP), while older forms of serial communication are being retired. This paper presents the selection, configuration and testing methodologies employed by researchers from the U.S. National Institute for Occupational Safety and Health (NIOSH) to integrate commercially available land mobile data radios into an existing leaky feeder communication system to provide IP data transport.IntroductionTo enhance the health and safety of their mining workforce, mine owners and operators are increasingly installing environmental monitoring and control systems in underground mines. Real-time, mine-wide monitoring is becoming a reality with the implementation of the Industrial Internet of Things (IIoT) into the underground mining industry (Zhou et al., 2017). However, not all underground mines, especially smaller mines and new development headings in larger mines, have the information technology infrastructure in place to handle the data transport requirements for the newer Internet Protocol (IP)-based technologies that are part of IIoT.This was the case with a mine in the Western United States. It lacked the infrastructure to perform critical monitoring in remote headings. Therefore, the mine partnered with the U.S. National Institute for Occupational Safety and Health’s (NIOSH) Spokane Mining Research Division (SMRD) to develop and evaluate a cost-effective solution for the real-time monitoring of geotechnical conditions in relatively remote sections of the mine. This paper describes SMRD’s solution to leverage the mine’s existing leaky feeder communications system to achieve IP data transport using commercially available land mobile data radios (NIOSH, 2013; Forooshani et al., 2013; Novak, Snyder and Kohler, 2010; Yarkan et al., 2009). The solution, fully evaluated in laboratory and mine environments, requires no modifications to the existing system, is economical, simple to implement, and reliable. It also allows for transition to higher-bandwidth IT networks, such as fiber optic or WiFi, should they become available."

Dec 1, 2018

By P. J. Brown, R. W. Nice

The Thalanga Copper-Lead-Zinc Concentrator in Northern Queensland was commissioned in early 1990. The design of a flotation process for the sequential production of separate copper, lead, and zinc concentrates has always been a most formidable mineral processing challenge. In 1988-1989 during the process design phase, sized fractions of various samples were subjected to quantitative and qualitative mineral analyses. These analytical techniques are collectively known as modal analysis. Modal analysis aided in the selection of key process treatment parameters for the initial laboratory testwork on the Thalanga ore. The work also guided the flowsheet development and quantified the mineralogically imposed limitations on the separation process. This paper describes in general terms how these modal techniques were used to guide the program of laboratory flotation testwork which constituted the flowsheet design phase of this project. During these design studies, the primary grind and regrind requirements were deduced and the basic flowsheet configuration selected. Recent operating plant performance data are to illustrate the value of modal methods in addressing complex metallurgical separation problems.

Jan 1, 1995

By G. S. Grainger, R. A. Cummings, F. S. Kendorski, R. L. Butts

Georgia Power Company's Rocky Mountain Project, located approximately ten miles northwest of Rome, Georgia, in the Valley and Ridge Physiographic Province, is a pumped-storage facility rated at approximately 800 megawatts of peaking energy. Geological field explorations and borings enabled the division of the rocks along the tunnel and shaft alignment into distinct lithologic units and defined the ground--water regime. Field explorations included a detailed analysis of the rock mass discontinuities at available rock unit exposures. Testing of rock strengths was performed in several phases in both the field and the laboratory. The field testing consisted of point-load testing, geophysical testing, in situ load testing, and hydro-fracture testing. Laboratory testing determined the Brazilian split-tensile strength, the unconfined compressive strength, the triaxial compressive strength, the joint-direct shear strength, and the pulse velocity. The rock mass along the tunnel and shaft was also characterized by empirical classification systems. The classification systems included the Rock Mass Rating (B1IR) and the Rock Mass Strength Determination (RHSD). The results of the field explorations, field testing, laboratory testing, and rock classifications were used to divide the rocks into two structural groups. These rock groups were defined as volumes of rock wherein the rock mass behaves similarly in response to the excavation. Each group, therefore, required separate rock engineering consideration.

Jan 1, 1986

By Mario Eduardo Rossi

The Universal Kriging (UK) and the Ordinary Kriging (OK) systems of equations are variations of the well-known system of Normal Equations. They differ only by the number of constraints present in the system. The dual version of these sytems enables one to interpret kriging as the fitting, of an interpolation surface, whose components are a series of variogram functions plus a polynomial trend model. This trend model should account for any systematic decrease or increase of the variable over the study area. It is shown that modeling the trend is useful only when the locations being estimated are beyond the range of influence of neighboring data (extrapolation cases). A case study based on a public-domain coal data set is presented. The variable described (seam thickness) shows an actual trend of increasing data values towards the NW corner of the region considered. UK and OK are used to estimate coal thickness at locations within sample data range (interpolation cases). The UK algorithm that includes a model for the trend does not improve the estimation when compared to the simpler OK algorithm with no trend model. Thus, in interpolation situations, the simpler OK algorithm is recommended.

Jan 1, 1989

By B. K. Mishra, R. K. Rajamani

This paper focuses on the use of a numerical tool known as the discrete element method (DEM) to study the motion of ball charge in ball mills. DEM is employed to simulate the motion of individual balls. While doing so, the effect of liner design on the grinding performance of the mill is studied. Two important, factors, such as the configuration of the liner and the geometry of the lifting surfaces, are correlated with the overall mill performance. An attempt is made to show the effectiveness of the lifter bars in transmitting power from the mill shell to the interior of the mill, with particular emphasis on large diameter mills.

Jan 1, 1994

By Brendan Demich, Brendan Macdonald, Timothy J. Orr, Jason Navoyski, Jennica L. Bellanca, William J. Helfrich

Recent advances in computing, rendering and display technologies have generated increased accessibility to virtual reality. Virtual reality allows for the creation of dynamic, high-fidelity environments to simulate dangerous situations and test conditions and to visualize concepts. Consequently, numerous products have been developed, but many of these are limited in scope. Therefore, U.S. National Institute for Occupational Safety and Health (NIOSH) researchers developed a virtual-reality framework, called VR Mine, to rapidly create an underground mine for human data collection, simulation, visualization and training. This paper describes the features of VR Mine, including mine generation, simulated networks, proximity detection systems, and the integration and visualization of real-time ventilation models.

By G. V. Krishna Roa, G. Vijaya Kumar

One of the main objectives while planning ventilation systems for mines with multiple fans is minimization of the total airpower consumption of the mine. Solution of this problem by conventional ventilation network analysis programs is tedious and time consuming, and may not yield optimum results in all the cases. The paper presents an algorithm for solving multiple fan networks by finding optimum combination of fan operating points for required airflow distribution in the ventilation system.

Jan 1, 1995

By S. K. Kawatra, S. J. Ripke

Finely disseminated iron ores compose much of today's reserves. After removing the silicate gangue, the resulting fine iron oxide concentrates require pelletization with a binder to enable transportation and reduction. Binders can be used more efficiently if their binding mechanisms can be completely understood. Typically, bentonite clay is needed as a binder to improve the strength of the pellets. Bentonite is an effective binder at a relatively low cost, but costs could be reduced further by replacing bentonite with even lower-cost binders, such as high-carbon Fly-Ash Based Binder (FBB). In this study, it was found that bentonite binds by a physical mechanism, while FBB binds by a chemical mechanism. These mechanisms were determined to be incompatible. Partial replacement of either binder with the other reduced dry magnetite pellet compressive strengths below the industrially acceptable value of 22.2 newtons (5 lbf). Activators and accelerators that activated the fly-ash deactivated the bentonite. The incompatibility of these two binders is explained.

Jan 1, 2000

By Jonathon M. Hanson, John F. Schatz

A combined theoretical and laboratory test program is described with the purpose of providing a useful model of the multiple radial fracturing process. A non-quantitative conceptual model is developed as the basis for detailed mathematical modeling and test planning. The model includes borehole pressurization, flaw rupture, and gas- driven fracture propagation phases. The laboratory tests are carried out in blocks of scaled rock simulant loaded to a true three-dimension stress state and with miniature propellant/explosive charges in a wellbore as the fracturing energy source. The conceptual model, fracture initiation modeling, and laboratory test setup have been completed and are described. The remaining work is ongoing

Jan 1, 1986

By Donald L. Meredith, Jeffrey Harris, Donald A. Stanley

Principal Components Analysis (PCA) is a versatile, multivariate statistical method that the Bureau of Mines is applying to mineral processing data to achieve data simplification and pattern recognition. The principal components are obtained from an eigenanalysis of the data matrix. To achieve data simplification PCA replaces a larger number of measured variables with a smaller set of principal components and at the same time removes a significant amount of experimental error. Data simplification and error reduction make PCA useful in process control. Plots of the individual principal components form the basis of a pattern recognition technique that allows detection of significant variations in the structure of the data. These applications of PCA are illustrated with appropriate mineral processing data.

Jan 1, 1993

By M. R. Yalamanchili, W. H. Jang, Y. Ye, J. D. Miller

Typically, rougher molybdenite flotation and recovery from bulk copper/molybdenum concentrates involves the use of alkalisulfides, Nokes reagents, cyanides, oxidants, and/or thermal treatment to depress copper sulfide minerals. The bulk copper/molybdenum feed generally varies from 0.2% Mo to 1.0% Mo, and with traditional reagents the single-stage rougher flotation recovery of molybdenite varies between 40% and 90% at a concentrate grade of 5% to 10% Mo. With ozone conditioning for copper depression, however, improved separations appear to be possible, as demonstrated by tests with Cu/Mo concentrates from both the Phelps Dodge Morenci Operations and the Kennecott Copperton Operations. Single-stage rougher flotation after ozone conditioning can provide a molybdenum concentrate at a recovery of more than 90% and a rougher concentrate grade higher than 20% Mo in some cases. Subsequent cleaner flotation with additional ozone conditioning resuIts in relatively copper-free molybdenum concentrates containing as much as 52% Mo. Preliminary analysis indicates that, with a multistage ozone conditioning/fotation strategy, the process is technically and economically viable and should be suitable for industrial ap¬plication.

Jan 1, 1991

By Yuusaku Tominaga, Sukumar Bandopadhyay

A power-series trend curve of elapsed time was estimated by using time series data of measured concentrations of carbon monoxide in the Taiheiyo coal mine, Hokkaido, Japan. The difference between the moving average concentration data and the estimated data from the trend curve showed linear correlation when plotted on a normal probability paper and a correlation coefficient value of 0.99. It is concluded that the estimate of carbon monoxide concentration using moving average values of concentrations compares very well with the results obtained from the trend curve within the three-sigma (standard deviation) range of the distribution. Thus, it is believed the results can be used to monitor and detect abnormal ventilation conditions in a ventilation network such as the occurrence of spontaneous combustion at an early stage.

Jan 1, 2002

By S. Lin, Y. J. Wang

Based on systematic definitions of a generalized multiple fan ventilation system, the concepts of an augmented system, its solution curve and the operating points of the original system are introduced. The Quasi-Newton algorithm is applied in combination with the switching-parameter method to ensure a continuous search along an augmented-system solution curve and identify all the possible system operating points on it. Two example networks are analyzed to demonstrate those concepts and the application of the algorithm for identifying operating points of multiple fan ventilation systems.

Jan 1, 1994

By W. D. Monaghan, G. L. Mowrey, C. W. Ganoe

In addition to developing various types of coal-interface detection systems, the US Bureau of Mines is actively involved in developing a coal rib-thickness monitoring system for high wall mining applications. One particular system that shows promise uses a ground-penetrating radar system to detect the coal-air boundaries of coal ribs. Based on preliminary laboratory and field tests, results indicate that this method can be applied successfully in highwall mines to maintain a constant rib thickness. The coal seam should be relatively clean in the vicinity of the antenna (e.g., have minimal partings or dirt bands) for best results.

Jan 1, 1996

If the communication/tracking system of an underground mine is severely damaged in a large mine accident or explosion, a surface based seismic system could be the only available tool for locating any trapped miners. This paper documents a field test of a seismic system at a room-and-pillar coal mine in Eastern Kentucky. Testing was performed at 6 different depths (450, 575, 750, 1175, 1525 and 1700 ft) above the mine. For each location underground, the miners pounded a ?set? of 5 ?repetitions? on the roof with each repetition being about one second apart. Over the 3 day field test, 63 sets of underground miners? pounding were detected by the seismic system at depths up to 1175 ft and at horizontal offsets up to 890 ft. Also during the testing, the observed signal strength generated by pounding with a crib blocks was seen to average 180% stronger than the observed signal strength generated by pounding with a sledgehammer. Ultimately, this field test was very successful and definitively demonstrated the ability of the seismic system to detect potential trapped miners? pounding up to a depth of 1175 ft.

Feb 23, 2014