Search Documents

By R. R. Jozefowicz, T. X. Ren, J. S. Edwards

The control of methane emission into underground mine workings is important both for the safety and productivity of the mine. As deeper and gasser coal seams are mined, ventilation methods involving increasing air pressures and quantities across mine workings may not be able to cope consistently with methane emission rates during the production cycle. An accurate prediction of methane emission into mine workings is of great significance in the design of ventilation systems and additional methane control methods if required. Research has been conducted to develop a numerical method for simulating methane flow through strata in which permeability is strongly influenced by mining-induced stress. To achieve this objective, both numerical modelling using Computational Fluid Dynamics (CFD) and laboratory tests on rock samples and granular materials under triaxial stress condition were carried out. Correlation has been established between stress and permeability characteristics of rock-measure rocks and laboratory results are being incorporated into the CFD models. This paper introduces the use of CFD techniques to model methane flow through permeable strata around longwall coal faces currently undertaken at the University of Nottingham.

Jan 1, 1997

By D. Kimball, P. Chambers

"BACKGROUND In the event of an explosion or fire in an underground mine, workers can be exposed to a deficiency of oxygen, an excess of carbon monoxide, or both. These threats can occur as separate conditions or simultaneously. A lack of oxygen in the breathing air can only be addressed via the use of a self-contained breathing apparatus (SCBA) acting as a source of oxygen. An excess of carbon monoxide can also be addressed via the use of an SCBA, but if the threat occurs in isolation (that is, the atmosphere still contains sufficient oxygen to support life) and the concentration of the threat gas is not extreme (< 2%) then the carbon monoxide threat can also be addressed by the use of a filter self-rescuer (FSR). Used together, the SCBA and FSR offer a far more efficient and universally capable life support system than when used in isolation. However, the SCBA does not take advantage of the fact that the surrounding atmosphere likely contains some level of useable oxygen; i.e., the SCBA always supplies the total required oxygen from its limited supply, resulting in a ceiling on its useful life regardless of the level of oxygen in the surrounding air. To address this technology gap, what is needed is a ""smart"" SCBA that provides filtration and catalytic protection against threat gasses and has an extended duration life-sustaining oxygen inhale stream independent of the threat content and oxygen deficiency of the surrounding atmosphere. DEVELOPMENT Developed under contract with NIOSH the Smart Escape SCBA is comprised of three major components including; 1) oxygen supply, 2) oxygen sensing & dosing electronics and, 3) a CO catalyst and carbon bed broad spectrum FSR. The SCBA is designed as a hybrid system that provides non-toxic breathing air by using an approved Chemical, Biological, Radiological and Nuclear filter self-rescuer and a catalyst to convert high levels of carbon monoxide to harmless carbon dioxide (CBRN FSR/CO). In addition, the Oxygen Sensing & Dosing Electronics (OSDE) package adds sufficient oxygen to make up for deficiencies detected in the ambient air (Figure 1). By making use of the ambient oxygen, less oxygen is required for a one-hour unit life. This means that the Smart Escape SCBA fits in a smaller and lighter package than a similar-duration conventional Self-Contained Self-Rescuers (SCSR). Alternatively, taking advantage of available ambient oxygen could offer a significant increase in working duration in a unit with the same size as current SCSRs. The research performed under this NIOSH contract involved numerous tasks including: (1) definition of performance and system requirements for the Smart Escape SCBA, including keeping environmental stressors within acceptable ranges, providing at least one hour of breathable oxygen supply, and using a mask or hood that allows high-quality voice communication; (2) designing, building, and evaluating prototype units to support extensive bench top testing at Avon Protection and third party labs to demonstrate the device’s capabilities; (3) building sufficient quantity of Smart Escape SCBAs designed to be intrinsically safe (per MSHA criteria); (4) testing and evaluation by the National Personal Protective Technology Laboratory (NPPTL)."

Jan 1, 2015

Introduction Agrico Mining Co.&apos;s Florida mining division has three surface mines and employs nearly 700 workers. The division produces some 6.3 Mt (7 million st) of phosphate rock annually. It is a good business. And Agrico has made it better by making it safer through a new approach to mine safety. In one year, Agrico - the second largest phosphate mining company in the US - recorded a stretch of one million manhours without an accident. That same year, the direct cost of accidents dropped to $9137 from a previous five-year average of about $50,000. Together with Don Roe, division manager of safety and security, Division General Manager Don Morrow made 1981 a watershed year for safety at Agrico. Morrow called on consultants from Safety Management Services of Du Pont&apos;s Specialty Services division to strengthen a safety program that was already better than average. From the late 1970s and into 1981, lost-workday cases (LWCs) were costing Agrico an estimated average of $22,000 each. And they were occurring with alarming frequency. In 1977, the company recorded six LWCs at an incidence rate of 0.64. This was followed by a jump to nine cases in 1978. In 1979, both occurrences and the rate increased - 10 LWCs at a 1.19 rate. The number of LWCs decreased to seven in 1980, with a rate of 0.71. Agrico instituted a far-reaching safety program in 1981, which began to take full effect in 1982. LWCs dropped from five in 1981, to three in 1982. And the direct cost plummeted from $110,346 to $28,828. In 1983, the mines recorded only one LWC. Its $9137 cost represented a reduction of $101,209 since the Safety Management Services of Du Pont had been called in. Through early 1984, the LWC incidence rate at the facility&apos;s three mines, phosphate drying plant, and transportation department was down to 0.26. This is 84% lower than the 1982 mining industry average, making it the safety leader among all Agrico companies, including its chemical plants. New Approach Agrico had the basics of a safety program in place when the Du Pont consultants arrived. But Du Pont suggested changes in responsibilities and company philosophy that formed the foundation of

Jan 1, 1985

By P. Somasundaran, D. R. Nagaraj, Jing Wang

Polysaccharides have been widely used as depressants in mineral processing for decades. They constituent one of the most abundant family of biopolymers. However, only a small number of them have been used by industry so far because of a general lack of understanding of interactions between these polymers and minerals. In this work, adsorption tests, electrophoretic mobility measurements, microflotation and fluorescence spectroscopic tests were performed along with computer simulation to explore the mechanistic aspects of guar gum adsorption and conformation on talc as a function of relevant variables such as ionic strength, pH, solvent composition and polymer molecular weight. From microflotation tests, it was found that talc hydrophobicity decreased markedly due to the adsorption of guar gum even at very low concentrations and reached a plateau below moximum adsorption. Guar gum adsorption on talc was found to be not affected significantly by changes in solution conditions such as pH and ionic strength, ruling out electrostatic force as controlling factor for adsorption. Fluorescence spectroscopic studies showed no evidence of the formation of hydrophobic domains at talc-aqueous interface. Also urea, a hydrogen bond breaker, reduced the adsorption of guar on talc. All of the above results suggest that one of the main driving forces for guar adsorption on talc is hydrogen bonding in preference to electrostatic or hydrophobic force. This information should help toward designing reagents of optimum molecular architecture for efficient depression, dispersion or other such surface modification of particles.

Jan 1, 2005

By Leonard H. Hoyle

The American Society of Association Executives is a professional society composed of nearly 10,000 individuals who serve as salaried executives on the staffs of more than 6,500 associations. Represented is the full range of international, national, regional, state and local associations...including trade associations, professional societies, philanthropic organizations and others. The dramatic growth of ASAE during the past 15 years is a manifestation of the growth of the association movement during the past two decades. This is not to imply that associations are a new phenomenon, because they have existed for thousands of years. Ancient civilizations show evidence of groups formed for mutual protection and advancement. In the transition from ancient to medieval time, trade associations and guilds came to serve an important function for the craftsmen and merchants they represented, encouraging the growth of new industries, improved processes and education.

Jan 1, 1981

By N. K. Riddle

In many mines, it is typical to stockpile material for milling based either on analyses from exploration and blasthole drilling, or on the observation and judgment of experienced personnel. New analytical instruments make it possible to perform multiple, rapid analyses of as-mined samples at or near the mining face, so that sorting into stockpiles can be much more accurate. Using data and operating practices from a phosphate mine, a model was developed to simulate the function of analytical instruments in ore-grade control and ore stockpiling. With this model, it is possible to determine the recommended sampling points and sample frequency to obtain the desired confidence limits on the stockpile analyses.

Jan 1, 2003

By S. S. Peng, V. Z. Sun

One of the major concerns of ground control in a coal mine is the prevention of roof, pillar and floor failures of the mine entry. To better design and evaluate the stability of a mine entry within a certain level of confidence, a reliability approach is introduced. The advantage of using the reliability approach, rather than the conventional safety-factor (SF) method, is that it not only takes variability of both rock/coal properties and stress into consideration but also assesses the stability of each component and the mine entry as a whole. Therefore, it is anticipated that by using this approach the current ground-control technology in a coal mine will convey a better sense of confidence. The results of a case study show that there is a significant difference in mine entry stability between the current design method and the reliability approach.

Jan 1, 1999

By Y. A. Attia, D. K. Sengupta, H. A. Hamza

Increased recycling of waste paper has been emphasized in recent years in both the United States and Canada for environmental and economic reasons. Removal of ink particles from waste paper pulp is therefore necessary. One of the most promising methods for ink removal is froth flotation. This study investigated the feasibility of a simplified flotation scheme and found that about 90% to 92% ink removal can be achieved. Also, a 95% to 97% ink removal is achievable if a hydrophobic polymer is used ahead of the flotation stage. Clean paper pulp recovery was over 90%. The effects of pulping pH, flotation pH and concentrations of flotation and polymeric reagents are discussed in the paper.

Jan 1, 1995

By C. P. Mangelsdorf

Introduction During the 13 years since C. C. White introduced the Birmingham roof truss there has been a revolution in permanent roof support technology. While not all of the emerging concepts have their origins in the truss-resin bolting is a prime example - the combinations and permutations of devices presently available to the underground mining industry reflect a well-spring of creative activity. The purpose of this report is to chronicle a number of roof support system that have same physical similarity to the Birmingham truss, and to report on their application. Definitions The application of the tern "truss" to the device developed by White of the Birmingham Bolt Company in 1967 may be derived from the classical technique of stifwood, by the attachment of an underslung, sometimes pretensioned metal strap, rod or cable. If the beam is separated from the reinforcement by a single block or vertical post it is called a "King&apos;s Post Truss". If two equally spaced blocks or posts are used it is referred to as "Queen&apos;s Post". When the immediate roof of a mine is visualized as a beam, the Birmingham device completes a structure resembling this latter form.

Jan 1, 1982

By T. X. Ren, J. S. Edwards

Although much work has been carried out in order to understand the mechanism of spontaneous combustion and hence minimise its potential risk, the spontaneous combustion of coal continues to be a problem in coal mining. The Department of Mineral Resources Engineering of Nottingham University has been active in conducting fundamental research into the problem of spontaneous combustion of coal. For years standardised adiabatic oxidation tests have been used to identify coals and other carbonaceous materials liable to spontaneous combustion. Recently the apparatus has been computerised and coupled with an expert system known as ESSH to evaluate the potential of self-heating of coal on the basis of intrinsic coal properties, geological settings and mining techniques. A numerical model has been developed to study the aerodynamics of airflow in the wastes of longwall coal faces. The Computational Fluid Dynamics approach is being explored to simulate airflow behaviour and nitrogen inertisation processes within the goaf. Such a model would be used in locating the areas most liable to spontaneous combustion and improving the utilisation of nitrogen. It would also be possible to determine the most likely path ways of combustion/heating products so as to provide an indication of the most appropriate locations for fire detectors.

Jan 1, 1997

By P. R. Dugan

Sulfur removal from high sulfur coal has several objectives including: a) reduction of the atmospheric load that contributes to the problem of acid precipitation; b) reduction of ash, which contributes to decreased energy transfer in boilers, as well as ash disposal; and c) alleviation of the social and economic dislocations related to uneven geographical distribution of sulfur in coal reserves. Cost in relation to the value of refined coal will govern the development of an emerging coal refining industry. Estimation of the premium paid by power companies for coal with a low sulfur content is a good estimate of the value that will be added as the result of refining. Estimates of premiums paid in 1984 are $28.65/t ($26 per st) for reduction of total sulfur from 370 to 1% S and greater than $28.65/t ($26 per st) for removal below 170 sulfur.

Jan 1, 1988

By Peter J. Alderson, M. P. Evans

The application of conveyor belting in bulk materials handling is crucial to the success of most mining enterprise selection of the cover rubber grade and thickness has a direct bearing on the cost per ton conveyed. Current and future demands placed on belt covers by higher speeds, increase capacities and greater lifts means today&apos;s cover will not be adequate for tomorrow&apos;s applications. The simple selections of RMA Grade I and I1 and MSHA above and below ground need to be expanded upon. This paper describes various new approaches for selecting conveyor belt covers for specific applications. It also presents examples of material and compounding techniques available to the belt manufacturer to improve the performance of their covers.

Jan 1, 1996

By Julia R. Budden

The role of bacterial oxidation in the mining industry is becoming more widely accepted. Western Australia has accepted the technology as a pretreatment for refractory gold concentrates more readily than most. The third of such plants has been completed at the Y ouanmi Gold Mine. This is situated approxi­mately 500 kilometres north east of Perth, in the Yilgarn mineral field. Y ouanmi concentrates are produced from underground ore and contain arsenopyrite and pyrite as the main sulphide miner­als. Refractory gold from this deposit is generally associated with the arsenopyrite portion of the material. Gold Mines of Australia Ltd ("GMA") initiated pilot scale testing at the BacTech premises in November 1993. The decision by GMA to use BacTech's technology was announced in February 1994. Design and construction commenced at this time. Bacterial growth on site was initiated in July 1994 and continuous opera­tion began in the October. Concentrate was added at 0.5 tonnes per hour and this has increased to 1 tonne per hour.

Jan 1, 1995

By Venkata S. Vutukuri

Assuming a number of discrete leakage paths and treating the airflow through leaky duct line as a series-parallel combination of airflows along the duct and through leakage paths, exact solutions for auxiliary ventilation problems can be obtained. A computer program "SEGMENT&apos;&apos; has been written to solve problems using this method. However, most of the investigators have treated the duct lines with a uniformly distributed leakage and many have derived formulas assuming various boundary conditions and levels of simplification for the design of a simple auxiliary ventilation system An appraisal of accuracy of the various formulas has been conducted using the results from the program "SEGMENT&apos; as benchmark and the formulas which give accurate results have been identified. The ranges of application for all the formulas have also been determined for 5 %error.

Jan 1, 1993

By M. Baumann

Operating and maintaining the heavy equipment used in open-pit mining operations is an ongoing challenge for mines. Typical operations employ a combination of shovels, wheel loaders, and haul trucks to excavate and transport the material for further processing. As this is the first point of contact for the material after blasting, it is often a bottleneck of all downstream processes, thus, equipment uptime and efficiency is crucial. Automated systems for bucket tooth monitoring, payload measurement, proximity detection, and rock fragmentation analysis will be examined. The impact of these systems on operation safety, efficiency, and reliability, in real-world scenarios will be investigated. The process of managing all the above fleet of equipment in a mine can be streamlined by connecting the equipment monitoring systems to a central server. Using the central server, the distribution of this information can be automated to ensure that the right people see the data in a timely manner, improving both proactive and reactive responses to threats to safety and productivity.

Feb 23, 2014

By Giuseppe Gaspari, Xiangrong Wang

The pandemic emergency is forcing transit agencies to define strategies allowing social distancing, which are more challenging in underground interchange stations in crowded downtown cores. Toronto Transit Commission’s (TTC’s) Bloor-Yonge Station Capacity Improvement Project in Toronto was approved to meet increasing demand and represents an opportunity to fight COVID-19. This paper discusses cost-effective solutions in expanding the cut-and-cover station box over the existing Toronto Subway Line 2 and connecting it through ventilation openings in the cast-iron tunnel liner. Potential uplift risks and structural damage due to minimal vertical clearance were analyzed via three-dimensional finite element analyses with advanced constitutive laws to simulate the multi-stage construction process. Based on the simulation results, a series of countermeasures, including excavation support systems, king posts, ground-consolidations, and liner reinforcements were integrated into comprehensive design options to ensure the serviceability and structural integrity of the subway tunnels.

Jun 13, 2021

By S. A. Diatchkov

Introduction There is a misconception that mineral-project economic evaluations in the former Soviet Union are either nonexistent or very limited. This is not the case. In fact, there are at least two basic methods that can be utilized to evaluate the vast mineral resources of the Commonwealth of Independent States (CIS). Evaluation procedures are based either on a comparison to known projects, which may rely on limited available data, or on potential-profit calculations, which generally uses more extensive databases. Significant philosophical differences between these systems and those utilized in the Western world include the following: •Under the centralized-government system, the economic evaluation of a mineral project was based on artificially determined mineral prices and costs. Every ten to 12 years, prices for concentrates and metals were established by the Council of Ministers and remained unchanged until the next reconsideration of prices . •The time value of invested money was not considered to be important under these "stable" prices, and inflation was assumed to be nonexistent in the planned economy. •An overestimation of the value of social and economic factors such as keeping the local population employed and providing the country with strategic minerals biased the economic evaluations of projects. Sequence of exploration Geological exploration in the CIS countries typically includes two major phases: prospecting and exploration. Prospecting consists of the following: •Regional geological studies. •General prospecting. •Prospecting. •Prospect evaluation. Regional geological studies are conducted within large territories and utilize satellite images, deep seismic zoning and other state-of-the-art methods. Geological and geophysical maps on a scale of from 1:200000 to 1:1000000 are developed to help identify regional anomalies and mineral prospective areas. The areas of primary interest are then subjected to general prospecting, beginning with geological mapping of the area at 1:50000 (1:25000) scale. The prospecting phase determines mineral potential based on further geological mapping (mostly 1:10000 scale), surface geophysics and geochemistry. Finally, the most attractive targets are subjected to further detailed evaluation (prospect evaluation) to help identify "possible" projects by means of trenching and wide-spaced drilling. The results of the prospect evaluation are analyzed and conclusions regarding the economical potential of the project are drawn. If the initial-prospecting phase results are positive and the prospect is recognized as economical, it then moves into preliminary exploration, which is followed by detailed exploration. Preliminary exploration determines the feasibility of the project on the basis of limited data. For example, in some underground projects, the initial exploration drilling and tunneling is done at two or three times wider spacing than would be required by the assumed mining method. Detailed exploration focuses on preparing the project for mining development, such as completing drilling and tunneling, particularly in the portion of the ore body to be first mined. During the project&apos;s mining phase, further exploration is usually conducted along the flanks of the mineralized structures and deeper sections of the ore body. Finally, during exploitation, it is sometimes necessary to delineate the ore body within the mining-block limits. A comparison between the United States (US) sequence of exploration activities and the CIS system is given in the Table 1. There is no "additional" and "exploitation" exploration shown in the US system, but it is common knowledge that all mineral projects are subjected to "additional" and "exploitation" exploration while being mined. An economic evaluation should be performed after the [ ]

Jan 1, 1996

By K. Ohga, V. J. Hucka

The presence of methane gas in mines creates hazards of explosions, fire and suffocation. Under certain conditions the occurrence of methane also poses a danger of gas and coal outbursts. Consequently, prevention of gas and coal outbursts in coal mines requires a sound knowledge of methane gas occurrence in mine workings. However, the direct method of determining methane content of coals developed by the U.S. Bureau of Mines is time and labor consuming for measurement, a new transportable methane tester was developed for Japanese coal mines. The instrument automatically measures emission gas from coal samples in the underground and also records and stores the data. Back on the surface, the tester can be connected via a RS 232 port to a PC computer for methane content estimation. Details of this technique are described here. Results on methane content determined in Japanese and U.S. western coal seams are discussed, as well.

Jan 1, 1991

By R. Svensson

Mill linings play an important role in all comminution processes with tumbling mills. The selection of the lining profile and the lining material has a great impact on overall grinding cost and mill throughput. The cost of the lining itself is minor in comparison with media cost, energy cost and the value of the material produced in the mill. The total scope must be considered when mill linings are selected. This paper presents case stories and explains the technology behind: •Different lining profiles in rubber and steel. •Orebed magnetic lining. •Steel-cap rubber lining. Introduction Grinding mill liner life has been a subject of extensive studies. Performance of mill liners in terms of wear life and how it relates to lining material and profile is abundant in the literature. The most economical liner material and design has been selected based on "cents per ton milled". The evaluation of the effect of liner design on power and grinding media consumption which is a far more significant part of grinding costs, has been less comprehensive (Fig. 1). Lining materials Steel. The most commonly used lining material is steel, calculated on a volume basis. Steel linings have a long tradition and a number of alloys is being developed. The main families are: •High chromium white iron. •Cr and Ni white iron (NiHard). •High chromium martensitic steel. •High carbon Cr-Mo perlitic steel. •High carbon Cr-Mor martensitic steel. •Manganese austenitic steel. Steel linings can be successfully used in most applications. Rubber. Rubber linings were introduced 25-30 years ago and are today commonly accepted to be the most economical linings for secondary and regrind applications. Rubber linings offer long service life in these applications and generally [ ] outlast steel in wet applications, where corrosion is a factor on the steel. The cost relation between rubber and steel has changed dramatically over the years. In the past rubber was more expensive than steel, but today, the cost of rubber is close to half the cost of steel, calculated on a volume basis (Fig. 2). The present cost situation has made rubber linings an economical alternative in several primary grinding applications as well. The wear rate of rubber in primary applications is higher than the wear rate of steel, thus giving a shorter wear life. This can be compensated for by making the rubber lining thicker. The cost advantage of the rubber allows for this, but care must be taken not to jeopardize the grinding performance. Rubber, as a lining material, offers some distinct advantages over steel lining, such as: •Ease of installation and removal. •Safer to handle, less risk of injuries. •Faster replacement. •Reduces noise.

Jan 1, 1996

By L. B. Rothfeld, R. L. Dolzani

This paper presents preliminary results of a US Bureau of Mines (USBM) study of potential costs of compliance with possible federal regulations for copper heap and dump leaching. The regulations could arise under amendments to the Resource Conservation and Recovery Act (RCRA) and/or the General Mining Law. Estimates are given for the cost of compliance with possible technology standards that would require the use of liners and closure caps regardless of terrain and underlying geology and hydrology. This cost is compared to the cost of compliance with 1992 state requirements for terrains typical of those found at existing copper leach sites in the southwestern United States. Incremental compliance costs are found to widely exceed screening criteria used by the US Environmental Protection Agency (EPA) to denote significant economic impact.

Jan 1, 1995