Search Documents

By Luis-Fernando Contreras, Juliano Maran, Richard LeSueur

A risk study was carried out at the Cerrejon coal mine in order to assess the impacts of pit slope failure in terms of safety of personnel and destruction of equipment with economic consequences. Results of the assessment enabled the definition of risk treatment requirements and the identification of key aspects to consider in a risk treatment plan. The approach included the following tasks: (1) Assessment of the total probability of failure (POF) representative of the stability conditions of typical footwall and highwall slopes. For this purpose, stability analyses were carried out to define the Design POF, which accounts for the variability of strength parameters and represents the normal conditions considered for slope design. Strength parameters for highwall slope analysis were derived from borehole data obtained with a geotechnical drilling campaign. The Total POF was estimated through the use of Source Response Diagrams (SRD) in order to incorporate other sources of uncertainty not accounted for, like changes in geometry, variability of rock conditions due to geological or operational factors, changes in groundwater conditions and occurrence of seismic events. (2) Assessment of the consequences of footwall and highwall slope failure on safety of personnel. The assessment was performed through the use of event tree analysis to establish the probability of fatality caused by slope failures, from the Total POF defined in the previous task. This analysis required the evaluation of personal exposure to slope failures. Also, the assessment included benchmarking of acceptability criteria in terms of probability of fatality and the evaluation of options of risk mitigation to comply with these criteria. (3) Assessment of the consequences of footwall and highwall slope failure in terms of economic losses associated with impact on equipment. The analysis included the evaluation of equipment exposure to slope failures, and it was performed through event tree analysis to establish the probability of an economic loss associated to total or partial lost of equipment, from the total POF value defined in the first task. The magnitude of the economic losses was estimated from the costs of damaged equipment, lost production and site restoration. Options of risk mitigation were also examined in terms of economic losses. The risk assessment process applied to the Cerrejón mine showed how the system can be applied to evaluate the consequences of failure in terms of personnel safety and economics and to identify the more adequate risk mitigation options. The system can be an extremely powerful tool in the mine design process and provides the opportunity to rationalize the geotechnical information requirements, once the risk criteria have been defined by management. The main purpose of this paper is to present the process; therefore, the emphasis has been put on the methodology followed rather than on the actual results obtained.

Jan 1, 2006

By C. Siyasiya

One of the problems that is occasionally encountered during the continuous casting of DIN 1.4003 stainless steel (hereafter referred to as 1.4003) is the side bulging effect, a problem that is generally prevalent in ferritic stainless steels. This occurs because the unconstrained narrow sides of the solidification shell are not able to withstand the ferrostatic pressure once the strand has emerged from the mould. Coupled with side bulging, there is strand width variation at high temperatures, i.e. when the steel is in the ferrite-austenite dual phase region. Both of these dimensional changes to the slab profile create some processing problems in subsequent hot rolling operations when unacceptable width variations are encountered. The strength of the solidification shell and its ability to withstand the ferrostatic pressure during continuous casting is dependent on its thickness and phase composition when exiting from the mould up to a few metres downstream. From the study of the high temperature metallurgical behaviour of this steel, it was observed that a thicker solidification shell when exiting from the mould and a higher austenite volume fraction in the steel would be favourable for the reduction of the side bulging effect during continuous casting. It was also found that as long as the d-ferrite to austenite phase ratio keeps fluctuating due to variations in chemical composition and process control in the dual phase region from cast to cast, the strand width variation problem would probably persist. The remedy to this effect lies in more strict chemical composition and process control during continuous casting of this steel. The hot ductility experiments revealed that 1.4003 exhibits good hot ductility in the strand straightening temperature range with a minimum of 75 per cent reduction in area and this was attributed to the high volume fraction of ferrite (0.2 to 0.4) in the steel. This would provide a remedy to side bulging by increasing the secondary cooling rate of the strand in order to form a thicker solidification shell without necessarily risking transverse cracking and other surface defects during unbending. Keywords: side wall bulging, resistance bending moment, applied bending moment, ferrostatic pressure.

Jan 1, 2005

By J. Lehmann, H. Gaye

A brief review of Computational Thermodynamics software concerning the modeling and prediction of reactions involving metals, slags and fluxes is presented. Their application for various steelmaking treatments is discussed. Examples concern phosphorus removal in BOF and EAF, ladle steel desulfurization, and specific treatments for inclusions control in semi-killed or Al-killed carbon and stainless steels.

By A. Bascetin

One very important aspect of mining is deciding what material in a deposit is worth mining and processing, versus what material should be considered waste. This decision is summarized by the cut-off grade policy. The cut-off grade strategy for an open pit mine influences the annual cash flows and affects the net present value of a project. The optimization of cut-off grade strategy requires the knowledge of detailed operational costs, mining sequence, mining operation, processing, and product constraints, as well as the grade distribution of a given deposit defined by pit, phase, and different material types. Cut-off grade optimization algorithms have been developed in the past. The most common criteria used in cut-off grade optimization is to maximize the net present value (NPV). This paper describes the determination of a cut-off grade strategy based on Lane?s algorithm adding an optimization factor based on the generalized reduced gradient (GRG) algorithm to maximize the project?s NPV. The introduced algorithm is a windows based program developed at Virginia Tech that is based on a series of Visual Basic routines within a spreadsheet environment (Excel).The benefits of the methodology are demonstrated using a hypothetical case study. Keywords: Cut-off grade optimization, net present value maximization, generalized reduced gradient algorithm method.

Jan 1, 2007

By Y. Rajpal

The Hedley and Grant pillar strength formula is widely used within the South African mining industry to calculate pillar strengths in bord and pillar mining layouts, and is currently being used at Bathopele Mine. Bathopele is an operation of Anglo American Platinum near Rustenburg, mining the UG2 reef at depths ranging from 40 m to 300 m below surface. The formula includes a parameter K, which is a downrated uniaxial compressive strength value of the rock, used to calculate the strength of a pillar. At Bathopele Mine, for the shallower areas Less than 150 m the value was 33 MPa, but this was increased to 44 MPa due to the fact that rock mass conditions improved and there were no incidence of failure in the shallower areas. Underground observations showed pillars to be stable with no signs of failure, and it was questioned whether the design was not still too conservative, resulting in sub-optimal extraction ratios and consequently a loss of revenue to the mine. A trial mining section was started at the mine where the pillars were reduced from 6 m x 6 m to 5 m x 5 m and the pillar behaviour was monitored for the onset of failure. Numerical modelling was conducted using the TEXAN code to back-analyse pillar stresses in order to find a more realistic value for K. Results from the trial section indicated that the pillar design was in fact too conservative, and the value for K was adjusted to 54 MPa for future designs. This paper details the findings from underground monitoring and numerical modelling results, and includes details for further calibration of the K value in order to further optimize the extraction of the orebody.

Jan 1, 2012

By T. Tholana, P. N. Neingo

"Mining companies globally are currently facing severe economic and financial challenges. In addition to global challenges, the South African mining industry has to face other operational challenges that are unique to the country and which threaten the survival and competitiveness of the industry. Profit margins are being squeezed by rising costs and decreasing commodity prices, while labour productivity is greatly affected by intermittent labour unrest. This paper analyses how the South African gold mining industry has performed pre-, during, and post the global financial crisis of 2008. The competitiveness of the industry in terms of labour productivity and industry cost curve position is analysed for the period 2006–2013 to assess the impacts of both the global financial crisis and labour unrest. An analysis of the South African gold mining industry is presented at company as well as mine level. Productivity measure in this paper is limited to labour productivity, in line with limited reporting on productivity. All the data analysed was obtained from the public domain. IntroductionSouth Africa dominated the world as the number one gold producer until 2009 when China took that position, and today South Africa ranks fifth after China, Australia, Russia, and the USA. According to Statistics South Africa (2009), South Africa still had about 30 years of production in the gold sector, a forecast that fluctuates based on the day’s modifying factors. Although South Africa has a comparative advantage in terms of minerals endowment, there are challenges faced by the mining industry that hinder translation of the comparative advantage into a competitive advantage. The industry continually seeks to address these challenges to remain competitive in global markets while addressing national and community needs.Neingo and Cawood (2014) argued that stakeholders in mining are continually concerned with mine management’s ability to translate use inputs effectively into quality outputs. They further suggested close monitoring of effective utilization of people, materials, and money to obtain maximum production of commodities under given conditions. Productivity is measured in various ways, including unit cost, output per employee, and output per unit capital equipment"

Jan 1, 2016

By A. D. Pienaar

The aqueous chemistry of niobium and tantalum compounds with hydrofluoric acid is a mature field of investigation. In contrast, very little attention has been paid to reactions of these compounds in non-aqueous environments. Similarly, reactions of elemental fluorine with niobium and tantalum compounds have received little more than cursory attention in literature. This work discusses the isothermal reaction kinetics derived from thermogravimetry, using a less redundant approach than is currently the standard. We also discuss the most likely kinetic models for this reaction.

Jan 1, 2012

By J. Kempken, R. Degel, J. Kunze, R. König

The FeNi technology is currently dominated by high-power submerged arc furnaces, often designed as smelter as "two-inline-solution". To achieve the intended high efficiency, state-of-the-art design in good correlation with ores and reductants and an integrated layout of the whole plant is of great importance. An introduction will be given to general aspects in the production FeNi, plus a detailed overview of design principles for large FeNi smelters and finally some examples of innovations and research projects concerning Fe-Ni.

Jan 1, 2007

The main objectives of the Mine Mechanisation and Automation program (MMAP) are to enhance health and safety in underground mining operations, facilitate mechanization and automation in narrow-vein and deep mines, provide sound science to regulatory agencies and improve mine profitability. The program, which has a unique underground and surface industrial scale facility, is involved in many multi-partner projects, like hydrogen fuelcell applications, electrification and hydraulification of underground mines, reduction of noise and vibration, miner location device, explosive-free blasting and hoisting. The paper presents an overview of the Mine Mechanisation and Automation Program of Natural Resources Canada and some of the main projects.

Jan 1, 2002

By B. P. Watson

The Bushveld platinum group metal deposits are two distinct, shallow-dipping stratiform tabular orebodies which strike for many hundreds of kilometres. Mining is extensive, with depths ranging from close-to-surface to 2 300 m. The mining method is a variation of planar open stoping. Pillars are widely employed to support the open stopes. In the deeper levels, in-stope pillars are required to fail in a stable manner soon after being cut, and the residual pillar strength is used to stabilize the hanging wall. These pillars are commonly known as crush pillars. Little work has been done in the past to determine pillar peak and residual strengths, and pillars have been designed using experience and formulae developed for other hard-rock mines. This has led to over and undersize pillars with consequential loss of ore, pillar bursts and potential collapses. This paper describes a crush pillar design methodology, and provides design charts. Three mining environments were incorporated in the investigations, which included underground and laboratory measurements, analytical solutions, numerical model sand back analyses. The results of the study are suitable for the areas where the research was carried out, and may also be applied with caution in other similar environments.

Jan 1, 2010

By D. B. Rebuli

Seismic networks in deep gold mines of South Africa are often planar owing to the tabular geometry of the orebody and, therefore, the mining infrastructure. Consequently, seismic event locations are poorly constrained in the direction perpendicular to the reef plane, and symmetrical locations above and below the reef plane may fit the observed data equally well. This problem may be resolved in situations where the strata above and below the reef plane have significantly different seismic velocities, which is the case for the Ventersdorp Contact Reef at Kusasalethu mine (previously Elandskraal, the amalgamation of Deelkraal and Elandsrand). A location method using a layered location model that takes into account the velocity contrast between the layers was tested. Observed direct- and head-waves were used to determine the velocity bounds of the P-wave velocities in the two-layer model. The data-set was also used to find the best P- and S-wave velocities for the two layers by grid searching over a range of velocities and minimizing the sum of the travel-time residuals. The results from the grid search and those from the calibration of velocities using direct- and head-waves give similar P-wave velocities for each of the two layers. A second set of seismic events was then relocated with this layered model and locations closer to reef were found. This simple layered location method goes some way to reduce the reefperpendicular location errors for Kusasalethu mine in particular. Keywords mine seismology, velocity model, location methods.

Jun 1, 2013

A number of impending and actual pit wall failures have been observed and documented, which have been interpreted to initiate on newly generated structural features. This infers failure through intact rock. Failure mechanisms have been postulated resulting from circumferential stress, extensional strain and brittle flexure. These will be discussed in the context of the failures and the associated monitoring. The implications of failure initiating on ?unknown? features has a significant impact for deep open pit mines where designs are based on the expected structural regime. Being able to anticipate such failures is important for design. Equally important is management of such changes as they arise. In this context, monitoring using high resolution microseismic techniques will be discussed as a means of providing early warning of such failures.

Jan 1, 2006

By M. K. Pelser

The purpose of this paper is not so much to provide a scientific study of the selection process for the perusal of other psychometrists or industrial psychologists?the purpose is to provide line management with a practical, relatively user-friendly guide to fair and scientific selection. The main areas that are to be covered are: ? Why fair and scientific selection? ? Job analysis ? The job requirement?selection technique circle ? Assessment centres in the mining industry?the Tavistock Collieries Ltd experience. Why fair and scientific selection? Seen from a line manager?s perspective, fair and scientific selection should be pursued for two main reasons: ? to remain within the ambits of the law ? to maximize the probability of selecting the potentially most productive and efficient candidate for the job.

Jan 1, 1997

This paper characterizes the copper cycle, that is, the flows of copper entering and leaving the African economy over a one-year period (1994). The major flows over the entire life-cycle of copper are examined; these include production (mining, milling and refining), fabrication of semi-products and manufacturing of finished products, use, and the waste management system. The results reveal that substantial amounts of copper (of order705 Gg/yr) are mined in Africa; of that amount, about 70 per cent is exported following processing, 18 per cent is utilized by African fabricators, and 12 per cent is discarded. The flows of copper products from African fabricators and product imports from other continents exceed product discards by large amounts. This difference, about 0.25 kg Cu/capita/yr on average, is added to in-use stock, largely as wire, plumbing tube, and in electronics. Some 65 per cent of the copper in discard flows is contained in electrical and electronic products, where it is relatively easy to collect and process for reuse. About a third of the copper discard flows known is recycled. The actual percentage is almost certainly higher because of informal (and unrecorded) recycling. Much of the remaining discarded copper is diluted into the municipal waste stream, where recovery and recycling are probably not economically justified. Keywords: material flow analysis, resource management, material budgets, copper, stocks and flows, systems analysis, Africa, developing country

Jan 1, 2003

By Ö. Erdem

The investment decision making process in the insurance and finance industries is affected by new advances such as simulation techniques. These advances have improved the discounted cash flow method (DCF). In DCF, a dynamic and flexible model construction is not possible because it does not consider uncertain conditions. Each project should be evaluated taking into account the related uncertainties because the related uncertainties determine the characterization of the project. Related uncertainties can be processed in dynamic DCF, which is applicable to both financial and non-financial industries with different kind of uncertainties, such as power generation and petroleum projects. The dynamic DCF method can estimate net present value (NPV) while managing related project uncertainties with a simulation method like Monte Carlo Simulation. The simulation method is preferred because its output is unbiased. Therefore, a more realistic financial evaluation of the project can be concluded. In spite of the improvement of dynamic DCF, this project evaluation method is not used frequently in mining industry. However, the mining industry is ideally suited to this concept because it is highly dependent on estimations such as orebody size and ore grade. During the project evaluation stage, these uncertainties can be included with the dynamic DCF method. This study aims to contribute to increasing the usage of this method in mining projects. A copper reserve in Turkey is selected as a case study to apply uncertainty assessment for the evaluation of NPV.

Jan 1, 2012

By U. Kumar

Product designed characteristics like reliability and maintainability affect maintenance cost, service performance, and therefore product support strategy must be defined during design stage in terms of these two dimensions. Furthermore product support and service delivery strategy has considerable influence on the total life cycle cost and the economic viability of industrial systems/products. he paper presents a concept for the development of service delivery strategy for industrial products with a special reference to mining systems. In this paper we emphasize that the strategy for product support should not be centred only on ‘product’ but it should also take into account the service delivery capability of the manufacturers/suppliers and users service organization, users competence and capability, product use location, logistics and infrastructures, etc., to arrive at the best performance and economic results. Such strategy should invariably include services supporting the client apart from considering services supporting the product. The discussion in the paper is based on the experiences from the manufacturing industry engaged in manufacturing of mining systems and the observed trends in technology and management of operation and maintenance of mining systems. Keywords: Maintenance and product support, Service supporting client, Service delivery strategy, Products reliability and maintainability, Product use location, Operating environment, etc.

Jan 1, 2003

By John V. Simmons, Peter J. Simpson

Excavated slopes in open pit coal mines are designed to be as steep as possible consistent with stability and safety requirements. Slope failures occur for many reasons, including oversteepening. This paper is concerned with slope design and excavation experience in the Bowen Basin coalfields of central Queensland (Figure 1), [ ]

Jan 1, 2006

As part of a comprehensive risk analysis which was carried out into the effectiveness of the water barrier between South Deep and Randfontein Estate mines, the potential threat posed by large seismic events was assessed. The study covered several aspects. Firstly, an estimate of the maximum credible earthquake was obtained from a probabilistic analysis of the regional seismicity of the previous 25 years. Allowance was made for ?reservoir-induced? effects by increasing the estimate of the size of the maximum credible earthquake from ML= 5.1 to ML= 5.5. Based on available knowledge of the geological structure, the possibility of such an event occurring in the vicinity of the barrier pillar was estimated. The possibility of substantial damage to the barrier rock mass, resulting as a consequence of a large event, was assessed. The likely damage to the concrete control plugs installed in five tunnels that penetrated the barrier, which might result from a ?near-miss? by the largest possible seismic event or from a ?direct hit? by a smaller event, was also considered. It was concluded that there was a negligibly small possibility that the maximum credible earthquake could occur close enough to the barrier, and in such a manner, as to cause any damage to it or to the plugs in the tunnels passing through it. The possibility of serious plug damage occurring as a result of a ?direct hit? by as maller event was slightly greater, but still sufficiently remote as to be of no practical concern at all.

Jan 1, 2006

By A. H. Mokken, G. K. I. Blendulf, N. R. Cowin, K. A. G. Blendulf

A study, by continuous monitoring of particle size in the cyclone overflow, of factors influencing run-of-mine mill performance by A. H. MOKKEN, B.Sc. (Eng.) (Rand) (Fellow), G. K. I. BLENDULF M.Sc. (Stockholm) (Member), K. A. G. BLENDULF, Dipl. (Min & Met) (Visitor), and N. R. COWIN, B.Sc. (Min. Tech.) (Visitor) An account is given of an investigation of the use of a continuous particle-size monitor - the PSM-IOO. The monitor system, in addition to showing marked variations in grinding fineness over short periods of time, particularly after stopping and re-starting the feed to the mill, has indicated weaknesses in accepted mill operating practice. The main potential of the system is the opportunity it has provided for almost complete automation of the milling circuit.

Jan 5, 1975

By L C. Pretorius

Pipe pigging is a technique for the in situ (field) coating application, to create a seamless internal anti-corrosive lining of long pipelines. The technology originated in the cleaning of pipes, and these proven cleaning methods continue to be used today. Firstly mechanical cleaning of the pipeline is performed, using wire brush, razor back, course stud and fine wire pigs, then foam pigs, or criss cross pigs, and urethane blade scrapers to remove loose debris, wax, residual hydrocarbons and corrosion products from the pipeline. Part of the proprietary techniques and expertise is to ensure that these cleaning pigs do not get stuck Next chemical cleaning of the pipeline is performed, using repeated pig runs with detergents, solvents, acid etching, corrosion inhibitors, consecutively batched between two pigs, to ensure a clean, dry metal finish to a visual cleanliness standard of ISO SA2½. These in situ techniques were developed, 40 years ago to apply internal corrosion protection to pipes using a thin layer of epoxy based paint (50 to 100 micron). Until recently these old techniques were never improved upon. Although many thousands of kilometres of pipes were successfully coated with these thin film epoxy based paints and old application techniques, these thin paint films had problems in weld coverage, and were also unable to fill pits caused by pitting corrosion, and unable to replace metal loss caused by channel erosion. New coating material developments, revised application methods and modified pigging equipment have now made it possible to apply thick film coatings as corrosion barriers to the internals of pipes in the field, using these pigging techniques. The thick coating films can be up to 1 mm (40 mils) thick in a single coating run over long distances. The new thick film coating materials and application techniques are similar to continuous screeding, creating a far more robust seamless internal pipe lining when compared to the old technology of thin film paints. With thick film polymers the option now exists to create a structural GRP pipe within a pipe, be it steel or cementicious. It has been preferable, even necessary, to move away from the traditional epoxy paints and coatings. It was found difficult or impossible to use epoxy materials for these pipe coating applications due to the requirement for achieving a suitable viscosity with adequate hold up. In order to reduce epoxy viscosity a solvent or reactive diluent is required. This inevitably lead to solvent entrapment and poor cure characteristics in cold climates. Further mud cracking in over thick areas, the inability to extend or reduce pot life, poor control of cure time and limited resistance to aggressive or chemical environments made solvent based epoxy resins a poor choice.

Jan 1, 2006