Search Documents

By Timo Niitti, Antti Rinne, Janne Turunen, Klaus Schommarz, Sami Grönstrand

This paper captures the essential steps employed in developing Outotec?s new FloatForceTM mechanism. The development of a flotation mechanism essentially revolves around the efficient transfer of installed power, or capital cost, to optimum flotation performance. Optimum flotation performance will be achieved if a balance between metallurgical results, operating and capital costs is maintained. The development of the FloatForceTM mechanism was done by careful evaluation of each of these three areas. This paper focuses on how experience, CFD and laboratory equipment, pilot and plant tests are used to test and evaluate a new flotation mechanism. Validated variables include mixing profile, power draw and local air hold-up. Metallurgical and mechanical design considerations are not covered in this paper. Besides using the FloatForceTM mechanism in new flotation equipment, the FloatForceTM mechanism can be used in existing flotation cell installations, thus enabling improvements in the mixing profiles, solids suspension and metallurgical performance of operating flotation circuits. Results of several tests carried out in existing plant operations are presented.

Jan 1, 2007

By V. Matou?ek

The paper addresses pipe flows of aqueous medium-sand slurries at velocities lower than the deposition-limit velocity. Laboratory test results including measurements of particle concentration distributions are used in order to describe a flow with a (pseudo-) linear concentration gradient above a stationary bed. Particle dispersion within the flow is evaluated and a stratification-ratio equation is formulated, estimating a portion of contact load in the flow. The formula is incorporated in the proposed predictive model for the hydraulic gradient for a medium-sand flow above a stationary bed.

Jan 1, 2007

By J. J. Taute, N. B. du Preez

"A well-performing solvent-extraction circuit is a key part of producing good quality copper cathode. To ensure consistent operation, a good understanding of the circuit’s operation and an ability to rapidly troubleshoot key parameters is required. This paper briefly discusses the modeling of solventextraction circuits. The paper then goes on to discuss the determination of key performance parameters from plant data and comparing these with the circuit models to quantify circuit performance. The identification and troubleshooting of circuit issues is presented with a worked example. INTRODUCTIONA well-performing solvent-extraction (SX) circuit is a key part of producing good quality copper cathode. To ensure a consistent, high-quality operation, a good understanding of the circuit performance is required. Evaluating the performance of an SX circuit is an extensive topic. The objective of this paper is to focus on the evaluation that the metallurgist should be performing on a regular basis using flow and concentration data. This paper does not cover important topics, such as crud management, phase continuity, or organic management. Some basic SX modeling concepts are first be presented. The calculation of the parameters is then presented with a brief discussion and recommended ranges (where applicable). A worked example is used to provide a basis for further discussion on the evaluation of the calculated parameters and use of data collected.BASIC SOLVENT-EXTRACTION MODELING CONCEPTSThis section presents the basic modeling concepts used in SX simulation packages currently available. SX reagent suppliers have invested significant time and effort into collecting data on the performance of their reagents under different conditions. Based on these data, suppliers have developed packages which they normally make available to their clients for free. These are typically used for process design and plant optimization studies. For example, BASF developed ISOCALCTM and CYTEC Industries developed MINCHEM® and MEUMTM.Chemistry of Copper Solvent ExtractionLiquid–liquid extraction involves the selective transfer of a substance between two immiscible liquid phases by controlling the relative solubility in each phase. In the case of copper SX, the exchange is typically achieved by an oxime-based chelating mechanism. In particular, mixtures of aldoxime and ketoxime are normally used in conjunction with modifiers. More detail on this extensive topic can be found in Schlesinger et al. (2011)."

Jan 1, 2015

By E. Córdova, A. Anani, W. Nyaaba

Optimization of panels, haulage fleet, and waiting area involves deterministic and low-fidelity methods and experiential knowledge. The process is challenging because coal recovery and operational capabilities must be considered in the solution. The approach in this manuscript comprises the development of an integrated stochastic simulation model of a coal room-and-pillar system that addresses these challenges. The decision variables evaluated are panel width, number of shuttle cars, and change-out time (COT). The results show that the mine should implement the shortest possible COT, decreasing the cycle time and thereby increasing productivity and continuous miner (CM) utilization. The highest productivity and CM utilization for a fleet size of three shuttle cars is found in the 15-entry panel width. For the evaluated fleet sizes, the 19-entry panel width is optimal for the four and five shuttle cars. Among the three variables studied, panel width and fleet size had the most significant effects (5% increase) on the CM productivity, cycle time, and utilization.

Apr 2, 2022

By A. Mitchell

On 25 August 2011, Andrew Mitchell, Lucas Moalusi, and Matthew van der Want of Bell Dewar hosted a presentation on Mining and Communities in Mooinooi, in the North-West Province. The conference was attended by traditional leaders in the North-West Province, officials from the Department of Local Government and Traditional Affairs, and executives from the mining industry. The presentation concerned traditional governance in mining, communities? rights in terms of applicable legislation, and the corporatization of community affairs.

Jan 1, 2012

By D. J. Hallbom

A new graphical method termed the ?Design Curve Diagram? (DCD) has been developed to analyse non-Newtonian pipe flow data by relating the plastic Karman number to the plastic Reynolds number. Since the plastic Karman number is directly proportional to the pressure loss gradient and the plastic Reynolds number is directly proportional to the velocity, the DCD is essentially a non-dimensional pipe flow curve. This makes the DCD conceptually easier than the commonly used Hedström-Moody diagram. While, the DCD was developed for the analysis of yield plastic fluids (e.g., Bingham plastics), it is equally applicable to Newtonian fluids.

Jan 1, 2007

By R. Thomas

A Honeywell TDC 2000 central process control system was installed at Rössing in 1984. The system controls the metallurgical operations from crushing to the finished product of uranium oxide and manufacture of sulphuric acid. The operation was previously controlled from nine separate local control rooms. The paper briefly reviews the design and commissioning of the control system on an operating plant and discusses the impact on manpower organisation and training needs. Development of the process control system during its first two years of operation is reviewed and a summary is given of the current status of computer control at Rössing. The impact of the new system on overall plant operation and performance efficiency is also briefly described. In conclusion, future developments of computer control and overall optimisation of metallurgical operations are reviewed.

Jan 1, 1987

By D. M. C. Valbom

The introduction of new diamond sorting technologies as well as additional manufacturers I vendors, has increased the equipment selection and combinations available for recovery flowsheet design. This paper describes the methodology used and the benefits realized in the design of recovery plants by ensuring a fundamental understanding of the advantages and limitations of the technology embodied in the equipment, a comprehensive knowledge of the ore body characteristics, and the effective matching of this information in combination with operational commercial requirements.

Jan 1, 2010

By L. Wade

The advent of relatively cheap computing power has precipitated a rapid growth of computer usage in the mining industry. In order to obtain most benefit from this development a need is recognised for the future mining graduate to be trained in computer literacy. This paper outlines the type of training required and describes progress to date with such a programme at the University of the Witwatersrand. Certain challenges concerning the teaching effort are discussed.

Jan 1, 1987

By I. M. Macleod

An adaptive steady-state on-line optimizing regulator is proposed as an integrated approach to the control of autogenous run-of-mine milling circuits. This optimizing regulator continuously estimates an internal model of the controlled process, and, based on this, determines mill fresh solids feed rate, mill water flow rate and sump water addition flow rate such that a circuit performance objective is optimized. The dual -requirement of controlling both the mill pulp load and the load of particles of grinding media size is thus directly and simultaneously addressed. The concept and theory underlying the operation of the adaptive optimizing regulator are discussed.

Jan 1, 1987

By A. Della Rocca, P. Jonker, B. Henning

Successful prediction of the collection efficiency of cyclone separators is a necessary step in cyclone design and verification. Aside from standard empirical relations, CFD modelling is widely adopted to supplement the design of cyclone units in relation to the desired separation performance. Nevertheless, effective adoption of numerical modelling is sometimes prevented by large modelling errors, especially for small size particles which are more subject to turbulence effects than larger particle classes. In the past, this motivated the adoption of more refined turbulence modelling approaches, such as large-eddy simulations. These approaches provide greater insight into time dependent behaviour, while leading to larger computational cost with respect to more standard approaches. In this paper, an effective Eulerian-Lagrangian Reynolds-averaged Navier-Stokes (RANS) approach is investigated, which is able to predict the complete separation efficiency curve with satisfactory accuracy, without requiring prohibitively long computational times. An assessment of the proposed approach is carried out against experimental data from large laboratory scale cyclones, in the form of mean and fluctuating velocity profiles from LDA measurements (Hoekstra, 2000), as well as with respect to the experimental separation curve (Zhao, 2005). The final application to a full-scale industrial cyclone unit is then carried out with the aim of tuning the cyclone design to the separation efficiency curve as required by downstream processes. Keywords: Cyclones, separation, CFD, RANS, RSM, Lagrangian

Jan 1, 2020

By O. Bazhko

Regular analysis of different streams is important for the control of hydrometallurgical processes. Various physical and physical-chemical methods are applied for this purpose. Many modern methods require costly equipment and are subject to interferences. Therefore, redoxtitration methods remain of interest. The use of different types of oxidizing and reducing agents as well as redox indicators enables many cations and anions to be rapidly and accurately analysed. Sometimes redox titrations require the prior preparation and addition of masking agents. Selective, sensitive and low-cost methods of redoxtitration of copper and SO2 in plant conditions are described.

Jan 1, 2009

By B. Mulcahy, M. Valenta

"The purpose of executing a project in a stagewise fashion is to evaluate all potential options in a cost-effective manner and develop an understanding of the project drivers, thereby minimizing overall project risk to the client. Among the more valuable tools for this exercise are production and financial models that can be used to quantify the sensitivity of the project to the critical parameters.The mine and concentrator used in this case study are located on the Kalahari Copper Belt, which extends from Zambia through northern Botswana into Namibia. This area of Africa has seen very little industrial development and the project will create much-needed employment and development in the region.The success of this project thus far can be attributed to the close cooperation between the geological, mining, and metallurgical disciplines. Regular updates of projected capital and operating cost estimates coupled with project outputs guided the teams in optimizing their various discipline models, ultimately delivering a compelling argument for the execution of the project. Key to the success was the development of a geometallurgical model for the prediction of concentrate tonnage, grade, and recovery for the life of the mine from the mining plan.This paper summarizes the metallurgical findings and the outcome of the various project stages. The development of the model is discussed, as are the challenges faced in developing a suitable metallurgical process route. IntroductionThe Kalahari Copper BeltThe Kalahari Copperbelt, which extends from Zambia across northwest Botswana into Namibia, is considered to be a broad time equivalent of the Central African Copperbelt, with a similar style of mineralization. However, at shallower depths (<25 m), chrysocolla and malachite exist in significant proportions in certain geological areas. As illustrated in Figure 1, the project is located in the Ghanzi-Chobe Fold Belt which forms part of the Kalahari Copper Belt. The Ghanzi Group, which overlies the lowest stratigraphic unit (the Kwebe Formation), consists of three formations, namely the Ngwako Pan, the D’Kar, and the Mamuno Formation (Hall, 2012)."

Jan 1, 2016

Mining executives often have a difficult task determining what the strategic objective of the business should be as this can be impacted by the prevailing market conditions. In addition, they have no mechanism to quantitatively &apos;test&apos; the impact of this strategic decision on the business and understand the underlying dynamics. During the commodities bull run of 2003 to 2008 the strategic objective may have been to grow the long term value of the business (NPV) through increased tonnage, acquisition and finding new reserves, which all came with an increasing fixed cost base. Now with the financial crisis upon us and the collapse of commodity prices and demand, executives have adjusted their strategies as &apos;cash is king&apos; and short-term cash flow, in some instances at the expense of long terms value, is the order of the day. For many mining companies, mine closures, reductions in production and cost cutting exercisers are now the focus. In many instances, management do not have an ability to rapidly test different strategic alternatives to &apos;test&apos; the impact on value, unit costs, reserves and profitability at the operational level and optimize the underlying trade-off variables. Economic modelling of the complete business value chain is a means of linking the operational &apos;reality&apos; and strategic choices, so that the full impact can be assessed. This paper describes some of the challenges facing mining executives and how economic modelling can be applied to make decision making more rigorous.

Jan 1, 2010

By Y. G. Che, M. Brown, R. L. Gandhi, M. D. Watson

Slurry pipelines have proven to be an economical method of mineral concentrate transport over long distances. Some of these pipelines are internally lined with high-density polyethylene (HDPE) to avoid internal corrosion. HDPE is an inert and extremely smooth material, and it was believed hat scale deposits would not form on it. However, there have been instances of scaling on HDPE lined pipes. Scale problems have also occurred on bare steel pipes. In this paper experience with scale problems in some of these pipelines will be summarized. Alternatives available for control of scale problems will be discussed, and a success story for the control of scale problems in the 300 km long Century zinc and lead slurry pipeline will be presented.

Jan 1, 2007

By M. L. Pududu, B. Ceki, K. Mohajane

This study was aimed at determining the effects of industrial action on profitability in the South African platinum mining sector. We compared companies where employees engaged in industrial action (affected companies) to strike-free companies (competing companies). Industrial action refers to strikes by rockdrillers, as these strikes typically result in the shutdown of production at the mines affected. A t-statistics analysis of significant differences in revenue and earnings of affected and non-affected platinum companies was conducted using data from platinum mining companies listed on the Johannesburg Stock Exchange from 2011 to 2015. Contrary to international studies, which suggest that the spillover effects of industrial action positively affect competing companies, our findings show that profits in the platinum sector decrease significantly during strike periods for both affected and competing companies. The results indicate industrial action is a threat to the profitability of all companies, and that employee demands should be prioritized and negotiated before they result in industrial action. Improved dialogue between management, labour unions, and employees in the platinum mining industry is recommended. The study contributes to the scanty literature on the effect of industrial action on the profitability of mining companies in a developing economy.

Dec 13, 2022

The President: We are very fortunate tonight to have with us Professor Franz Pawlek, Head of the Institute of Extractive Metallurgy for Non-Ferrous Metals of the Technical University, Berlin. In him we have a representative from one of the few mining and metallurgical universities in Western Germany, since I understand there are only three such universities, Berlin, Aachen and Kassel. The latter is represented by Mr Schmelling who has accompanied Professor Pawlek here tonight. The famous Freiberg University is on the other side of the Iron Curtain, and so is Breslau. Professor Pawlek was born in Vienna many, many years ago, and he obtained his diploma and then later his Doctor&apos;s Degree in metallurgy, in Vienna. For four years he worked for an Austrian company, and then moved to Berlin and joined the A.E.G. Company. After the war, he joined the Institute, which had been very heavily damaged, and he was closely associated with the rebuilding and re-equipping of the faculty of mining and metallurgy. He has written numerous papers, and I am sure we are going to have a most entertaining and interesting evening&apos;s talk. The President: Gentlemen, I am sure you would like me to thank Professor Pawlek for his talk tonight. My knowledge of pressure leaching is particularly small, limited to a friendship with Professor Frank Forward, to whose original work at Fort Saskatchewan reference has been made by Professor Pawlek. I enjoyed Professor Pawlek&apos;s talk, and as a mining engineer I managed to follow most of the argument, mainly because it was so lucidly presented, aided by these informative slides; but I never realised how complicated a problem this process can be. I am taking the liberty of asking Professor Howat to express our thanks from a more technical point of view. After Professor Howat has spoken, and possibly posed a few questions, I shall throw the meeting open in the hope that various people here will be prepared to ask questions. I see one or two gentlemen who have been over in Canada studying pressure leaching lately, and I hope they will ask questions, informally if they so wish. We will not record the full proceedings of this meeting tonight, in the hope that there will be more questions of a general nature. Thank you. Professor Howat: Mr President, Professor Pawlek, I am afraid I am up here under false pretences, because the matter that I thought I was asked to do was to propose a word of thanks, and I usually thought that a word of thanks was taken at the end,-however. It is always very intriguing to think that for all these thousands of years that have passed, pyrometallurgical processes have provided the main methods of extracting metals from their ores. Within the last 100 years, hydro metallurgical processes have become of increasing importance, and it is quite interesting to speculate that the largest single hydrometallurgical process is the one that we operate in this country,-which was devised by two distinguished countrymen of mine,-namely, McArthur and Forrest.

By T. Bezuidenhout, J. D. Visagie

In recent years the requirements for a barrier system between the waste body of tailings storage facilities (TSFs) and the natural ground (NG) has necessitated the use of HDPE-lined TSFs in South Africa and other countries. The addition of an HDPE liner creates an interface between, inter alia, the tailings and surrounding soils on the footprint of the TSF. It is known that low-strength materials beneath slopes can cause slope instability. One method which can theoretically mitigate this instability of a lined TSF is the addition of stability bunds along the footprint of the TSF. Altering the profile of the footprint to include slope changes which oppose the direction of the failure creates passive slices in a limit equilibrium analysis. The passive slices actively oppose the movement of active slices, resisting the mobilization of tailings, thus greater active slice forces are required to develop a failure surface running along the liner interface. Two scenarios are presented and compared. The first scenario retains the ground profile unaltered and the second scenario includes stability bunds along the ground profile. An in-depth assessment is made of the interslice forces and the interface shear stresses for each scenario. The theoretical background is discussed in greater detail to determine the mechanisms of reinforcement provided by the bunds.

Jun 2, 2022

By C. Hey

The cycloned gravitated tailings backfill system, also referred to as a soft or low density fill, has been implemented at Vaal Reefs. Inhibiting the success of the system was the problem of shrinkage after placement. The problem was overcome by a pressure fill technique which eliminated settlement, contained costs and allowed remote placement. The technique involves the preinstallation of disposable pipes which are filled cyclically until a residual pressure of 0,5 bar of active support is generated in the filled paddock.

Jan 1, 1988

By F. Lanaro, K. Röshoff, R. Christiansson, L. Jing

This paper presents the results of a project for developing a methodology for empirically determining some of the mechanical properties of the rock mass at the Äspö Hard Rock Laboratory, Southern Sweden. Using the equations available in the literature, the deformation modulus, friction angle, cohesion and unconfined compressive strength of the rock mass were estimated. A comparison of the results using different classification methods (Q, RMR, GSI, RMi, Ramamurthy’s) was made to estimate the range of variations in the mechanical properties with the considerations of: i) the quality/quantity of the geological data; ii) the technique for partitioning of the rock mass into homogeneous domains; iii) the sensitivity and subjectivity of the empirical methods; and iv) the need for validating the empirical methods against a test case. Cet article présente les résultats d’un projet visant à établir une méthodologie, pour déterminer, de façon empirique, les propriétés mécaniques de la masse rocheuse. En utilisant les corrélations disponibles dans la littérature, quelques-unes des propriétés de la masse rocheuse ont pu être déterminées (module de déformation, angle de friction, cohésion, force de compression illimitée). Une comparaison des résultats obtenus par différentes méthodes (Q, RMR, GSI, RMi, de Ramamurthy) a permis d’établir une échelle de variations des propriétés mécaniques et de formuler une série de recommandations concernant : i) la qualité/quantité des données géologiques ; ii) la technique de partition de la masse rocheuse dans des domaines homogènes ; iii) la sensibilité et la subjectivité des méthodes empiriques ; iv) la nécessité de valider les méthodes empiriques à l’aide de nouvelles études de cas. Dieses Paper präsentiert die Ergebnisse eines Projekts mit dem Ziel, eine Methodik für die empirische Festhellung von mechanischen Eigenschaften im Gesteinmassiv zu etablieren. Durch Verwendung der in der Literatur zugänglichen Korrelationen, wurden einige Eigenschaften des Gesteinmassivs festgestellt (Entstellungsmodul, Reibungswinkel, Kohäsion, unbeschränkte Kompressionsstärke). Ein Vergleich der Ergebnisse unterschiedlicher Methoden (Q, RMR, GSI, RMi, Ramamurthy’s) wurde durchgeführt und dies erlaubte die Feststellung der Variationsskala von den mechanischen Eigenschaften, sowie eine Reihe Empfehlungen für: i) Qualität/Quantität der geologischen Dateien; ii) die Technik für Teilung des Gesteinmassivs in homogene Domäne; iii)die Empfindlichkeit und Subjektivität der empirischen Methoden; iv) das Bedarf die empirische Methoden gegen neue Fallgeschichten zu validieren.

Jan 1, 2003