Search Documents

By J. W. van der Merwe

Technology is advancing at a rate that makes it extremely difficult for the mining industry to keep pace. Many advances occur within a given piece of technology and often this is missed by the disciplines that could have gained advantage by its implementation. Often this may have been simply an aspect of cost exceeding benefit. However, there are some technologies that potentially have such a far-reaching impact on the mining industry that the benefits simply outweigh the cost. The application of 3D laser scanning in the mining industry has the potential of taking the concept of 'Google maps?' underground. This presents an opportunity where the virtual world of underground can be traversed with relative ease and many aspects of measurements could be obtained without having to visit the working place again, potentially saving countless man-hours and still delivering precision work with significant savings in downtime, stoppages, and exposure to safety incidents. Anglo American Platinum maintains its competitive advantage though the review and application of appropriate technology. This paper describes the 3D laser scanning trial at one of Anglo American Platinum's new shafts, and goes on to show the benefits encountered through the application and the involvement of the various MRM disciplines.

Jan 1, 2013

By H. E. Bartlett

Previously, the grade of ore at the shaft head was taken to be equivalent to the grade measured in the faces by means of chip sampling. The tonnage mined from the stopes is determined from survey volumetric measurements. Estimates of shaft head grade and tons include the grades and tons of waste, development ore, sweepings from old areas, and other sources, not all of which are sampled. The tonnage of ore delivered at the shaft is often estimated using skip factors. These factors are subject to manipulation and not all the skips are filled to the same level. Consequently, both the grade and tonnage of ore delivered at shaft head are subject to a measure of uncertainty. For many years, these uncertainties have led to disputes between shaft managers and metallurgists over the reconciliation between shaft tons and grade and plant tons and grade. These problems are compounded when several shafts feed a central processing plant. Shaft bonuses and a shaft?s profitability are affected by poor gold allocation methods. Without measurement of the grade and tonnage from all shafts, a poorly performing shaft could benefit at the expense of the other shafts. In order to improve the measurement of grades and tonnage at the shaft head, which is the custody transfer point between the mine and surface operations, South African mining companies have developed a methodology to measure the mass of ore from each shaft using rail weighing equipment, and the run-of-mine grades delivered from each shaft using cross-stream (go-belt) sampling. Harmony Gold Mining Company has implemented the rail weighing and go-belt sampling methods for their shafts. This paper deals with the statistical tests on the procedures and control measures that are in place to establish confidence in the gold allocations. The metal accounting system for examining the allocations follows the first principle of the AMIRA P754 Metal Accounting Code of Practice namely ?The metal accounting system must be based on accurate measurements of mass and metal content. It must be based on a full check-in check-out system?. The check-in is mass and grade of run-of-mine ore and the check-outs are the plant input grades and the recovery and residue from the plant. The balances between check-in and check-out are the subject of the statistical analyses, which have been conducted using the classical statistical tests and procedures that are generally used in all fields of endeavour. It is concluded that the gold allocation procedures that rely on go-belt sampling and rail weighing of ore from shafts has been successfully implemented, and that the system, which has been in operation at Harmony since 1993, has won general acceptance from stakeholders, with the gold allocations being perceived as being fair to all. Apart from the on-mine issues of bonuses and fair allocations, accurate metal accounting assists in the broader issues of generating accurate production figures for management. An added benefit of weighing and sampling ore at the shaft head has been that shafts now have daily moving average grades, which are used for grade control. The go-belt sample at the shaft head is the first accurate sample of production in the value chain from face sampling to gold bullion. Keywords metal accounting, go-belt sampling, run-of-mine sampling, codes of practice, AMIRA P754, train weighing, statistical analysis, gold split, allocation of gold, metal balance, grade control.

Jan 1, 2014

Slake durability of rocks is an important property of rock-mass and rock-materials in geotechnical practice. The slake durability of rocks is closely related to their mechanical properties. In this paper, mechanical properties and slake durability tests for weak and clay-bearing rocks from Beypazari Trona Bed in Ankara, were performed in order to assess the slake durability and mechanical properties (especially rock strength) of these rocks as well as to understand the relationship between mechanical properties and slake durability. In performing this relationship, statistical based correlation has been applied.

Jan 1, 2003

By B. P. Watson

The discussion written by Dr de Frey suggests that mine design should be based on closely spaced stability pillars. However, this concept leads to low extraction ratios at depth. The concept of `crush' pillars in conjunction with more widely, appropriately spaced stability pillars allows for significantly larger extraction ratios, particularly at depth. It should be noted that the rock conditions in many areas of South African platinum and gold mines are good, allowing significant spans to be mined safely between stability pillars. `Crush' pillars are cut small enough to fail stably near the face under stiff loading conditions, and their residual strength is intended to support about 10 m rock height between stability pillars. While this support resistance cannot be achieved by conventional support, crush pillars have been proven to have the required capacity for this purpose. The concept of leaving smaller crush pillars with appropriately positioned stability pillars has been used successfully for more than 30 years in areas of South African platinum and gold mines.

Jan 1, 2011

By R. Lechuti-Tlhalerwa

"Geometallurgy aims to improve mining project value by predicting the impact that ore and waste characteristics will have on mining and metallurgical processes. This requires integration of rich spatial models of orebody characteristics with validated process response models. These models have, until recently, been constrained by the spatial coverage and representativity of relevant data and the ability to validate predictions made.The revolution in the diversity and volume of data and computational power that is now becoming available for integrated geoscientific modelling of orebodies, and stochastic simulation of mining and mineral processes is accelerating. By embracing emergent integrated data analysis and simulation techniques, geoscientists and engineers can lead a transformation in the way the mining value chain, from orebody to recovery, can be conceived, evaluated, and operated by using the geometallurgical paradigm.This paper describes a methodology that is applied to an existing diamond operation. Analysis of spatial and process data is used to build an integrated geometallurgical value chain model (IGVCM). This IGVCM is used to generate geometallurgical options and evaluate their potential outcomes. The model facilitates the use of flexible, highly configurable, and potentially automated intelligent approaches to evaluate mining and mineral process configuration, and results in more robust design outcomes. The approach described here, and its successful implementation has potential to deliver step-changes in value. IntroductionGeometallurgy aims to identify treatability risks – and opportunities – that arise from the interaction of orebody characteristics with mining and treatment. Improved understanding of the rock/process relationships allows project planners and production teams to predict performance, identify potential shortfalls, and thus enable the proactive creation and evaluation of strategies to mitigate these risks. These advanced insights also create opportunities for continually improving operational performance through dynamically adapting and improving the process response to the changing properties of the ore (Figure 1)."

Apr 1, 2019

By D. E. Kraushaar

Ruhrkohle in West Germany evaluates and compares the net present values of long-term periods from its coal mines by a computer assisted long-term planning system. Two main parts of this system are computer programs for the prediction of: (a) mineable reserves and their distribution in longwall panels as a function of dependent geological variables; (b) daily outputs and costs of longwall panels as a function of dependent geo- logical, layout and operational variables. This paper describes the investigations, which ended in the above computer programs: ? the collection of information from past workings and their organization in databases; ? the statistical evaluation of the databases, and ? the resulting correlation formulas. The correlation formulas vary the mean dependent variables as a function of independent variables which can be indicated with high reliability for planning projects in the long run. The system thus serves the purpose of facilitating long-term planning and excluding biased individual judgement of local planning staffs.

Jan 1, 1987

By M. Gomo, L. S. Mokhahlane

"Underground coal gasification (UCG) is an unconventional mining method that converts coal in situ into a fuel gas that can be used for electricity generation. Residue products from UCG have the potential to leach into surrounding groundwaters. The geochemistry and leaching dynamics of these products are explored in this study. The products include char, ash, and the heat-affected zone in the surrounding rocks. Core samples from the pilot plant at Majuba are the first ever to be recovered from a UCG cavity in Africa, and they give key insights into the geochemistry of the gasification zone. Mineralogical and chemical analyses were performed on the samples, and acid-base accounting (ABA) was used to predict the acid-producing capacity of the gasification zone, particularly for char samples. Some of the char contained pyrite, although not all samples were acid-producing as determined by the ABA analysis. The ABA results showed that some of the unburned coal has moderate levels of sulphur, which could be the driving medium for acidic conditions. The ABA analysis indicated that water in contact with the gasification zone would eventually have a pH lower than 7, which could lead to acid rock drainage. These results form part of a preliminary investigation into the geochemistry of the reaction zone, post gasification. IntroductionUnderground coal gasification (UCG) is an unconventional mining method that converts coal in situ into a fuel gas that can be used for industrial purposes, including electricity generation. The gasification process leads to the formation of a cavity composed of char, rubble, and void space (Bhutto, Bazmi, and Zahedi, 2013). Residue products from UCG have the potential to leach into groundwater. These products include char (devolatilized coal), which can generate acid rock drainage (ARD). ARD is caused by the oxidation of sulphide minerals, which acidifies the leachate, thus increasing the solubility of some environmentally toxic metals (As, Cd, Hg, Pb, Zn, etc.) (Bouzahzah et al., 2015).The main source of ARD is oxidation of sulphide-bearing minerals due to interactions with oxygen, water, and microorganisms (Simate and Ndlovu, 2014; Kefeni, Msagati, and Mamba, 2017; Bouzahzah et al., 2015). Although ARD occurs naturally, it can be enhanced by mining activities that escalate exposure of sulphide minerals to water, air, and bacteria (Simate and Ndlovu, 2014). At the Majuba pilot plant, the unburned coal remaining in the cavity has been in contact with groundwater since the gasifier was shut down in 2013. It is possible that in a commercial UCG plant, most of the coal will be consumed and no unburnt coal will be left in the cavity. Most of the sulphur will be converted to H2S during the gasification process and transported with the syngas to surface, where it can be removed and captured as elemental sulphur."

Oct 1, 2018

By R. Layton

Expert Systems Technology (EST) is becoming more and more widespread in both its range of applications and the public interest. It appears to be capable of performing tasks unmatched by other techniques. Within the mining industry a large body of unsolved problems now appear to have a solution. This paper examines the current state of EST both in the context of the history of Artificial Intelligence and current efforts at building mining expert systems. It provides recommendations for those wishing to get involved, and outlines the problems for those who believe that expert systems are capable of anything and everything. The paper also provides a detailed analysis of limitations of current EST that must direct research into more fundamental, commonsense areas than have been extensively covered before.

Jan 1, 1987

By C. Pamukcu

In this paper, which is aimed to serve as a review article, first of all a breakdown of the earth?s total water reserves is given. The usage areas of water in the mining industry are mentioned and these uses are briefly outlined, together with the main pollution potential of each. According to this, most of the water (almost 80% of it) is utilized in processing. Later on, probable damages that the mining would give to groundwater as a result of acid mine drainage, heavy metal pollution, euthrophication and deoxygenation is described. Finally, the measures and controls that should be taken against water contamination in mines are presented.

Jan 1, 2008

By L. I. Boshoff, S. Gracie

This paper discusses pilot and laboratory-scale metallurgical test work conducted on bulk samples from a low grade heavy mineral deposit and provides an overview of basic practical metallurgical techniques applied to ascertain the suitability of existing production plants to process material from this orebody. Previous investigations have shown this specific orebody to be more challenging in terms of mineral beneficiation as it has a high gangue mineral content. Test work was conducted on targeted stratigraphic units based on lithology and assay results to enable identification of the stratigraphic units portraying quality issues. Unit specific metallurgical pilot work has never been conducted on any of the RBM orebodies and is a new field currently being explored. During this investigation focus was placed on potential quality and yield issues for ilmenite product, with particular reference to CaO quality. A basic evaluation of zircon and rutile separability was also conducted. The test work was conducted using a comparative baseline methodology with metallurgical test work methods specifically aiming at mimicking the existing production plant as closely as possible. This enabled not only the likely metallurgical performance to be assessed but also indicated whether current plant design would be suitable to process the low grade ore types into products of acceptable quality at acceptable yields. The methods and findings discussed in this paper indicate that although there is considerable variation between different units, a blended feed can be successfully processed. With unit specific metallurgical data applied to the existing geological block model, expected yields and recoveries using current plant designs could be predicted.

Jan 1, 2007

By S. Zhao, S. P. He, M. Y. Zhu, Y. Tao

"The effect of two refining slags (A: 1.0–1.8 CaO/Al2O3 ratio, 11–20 wt% SiO2; and B: 1.0–1.2 CaO/SiO2 ratio, 25–35 wt% Al2O3) on the inclusion morphology of a carbon structural steel (Q235B) was studied by controlling the balance between the steel and the refining slag at 1600ºC in a Si–Mo resistance laboratory furnace. The results showed that most of the inclusions in the molten steel balanced with slag A were formed by a lowmelting CaO–MgO–Al2O3–SiO2 system with a total oxygen content (T[O]) being fixed at 6–13 ppm. The inclusions in liquid steel balanced with the slag B were mostly formed by the CaO–MnO–Al2O3–SiO2 system, with T[O] controlled to 19–26 ppm. The overall size of the inclusions under balance conditions was higher in the steel reacted with the slag B than that reacted with slag A, with the latter showing more inclusions smaller than 3 um. In order to generate a large number of spherical CaO–MgO–Al2O3–SiO2 inclusions smaller than 3 ??m while decreasing the T[O] in the resulting steel, the composition of slag A should be used. This composition allowed improving the cleanliness of the slab, and is also advantageous for the castability of the molten steel. IntroductionThe sample used in this study was a typical carbon steel manufactured by CQ Steel. The galvanized, tinned, and plastic composite steel plates made of the original plates are used extensively for decorative panels, general dust pipes, drums, instrument cases, switchboxes, and train cars, among other uses. The target control composition is shown in Table I. The S and P contents are usually fixed during production below 0.020 and 0.025 wt%, respectively, with the aim of reducing longitudinal cracks on the slab surface."

Jan 1, 2017

By R. R. M. Cousens, W. S. Garrett

Discussion: L. T. Campbell Pitt: When Mr Garrett and I discussed the design and construction of plugs and bulk head doors to resist great water pressures in mines about ten years ago, we visualized an emeregeny when there would be no time for site preparation. We could not however, anticipate a problem of such magnitude and urgency as the one described in the paper under discussion. The paper very clearly describes the flooding and the measures taken to save the mine. The complete flooding would have been a national disaster. The account of the combat between man and water reads like the account of a military operation. It was an endeavour which achieved success because there was a master plan, tenacity and, in fact, heroism. The paper is of necessity a long one. In my contribution I will mention some historical facts and factors that I believe have relevance to the flooding and the saving of the mine. It is of great satisfaction to me to have been one of the two initiators of a new approach to underground plug design and construction. The investigation was taken over by a Chamber of Mines Committee which combined our early work with further research and the resulting data had a significant bearing on the West Drie emergency plug designs. The final plug length was correctly based on the requirements to obviate leakage. A plug to have structural strength only would have been very much shorter but so ineffective as to have become a waste of labour, material, and in consequence, wasted the limited time available to prevent flooding of the whole mine. The figure of 75 lb per sq in. sheer stress provided a very ample margin, in my opinion, but under the very difficult site conditions and the limitations of plug material suitable for the very unusual construction, justified such a figure. There must have been considerable temptation to reduce the safety margin due to the urgency to complete and commission the plugs, but it is much to the credit of the directors of this operation that nothing less than a safe design was permitted. In about 1945 Blyvooruitzicht Gold Mining Company, which was then mining in to the West Driefontein area to assist in early development, decided to protect themselves from a possible inrush of water from the latter mine. A bulk head door was accordingly designed and installed on 2 level between 1945 and 1948 at 4,218 ft below surface. Since West Driefontein paid for it, Gold Fields consulting mechanical engineers collaborated with their colleagues of Rand Mines who completed their design after a few modifications were agreed. This door was never used to prevent an inrush into Blyvooruitzicht but the exercise was very useful to Gold Fields when the high pressure doors initially installed on 10 and 12 levels between Nos. 2 and 3 shafts to enable isolation of one section of the mine from another were designed. At that time the capacity of West Driefontein to cope with an inrush of water was comparatively small because the storage in stoped areas and the installed pump capacity were much less than in later years. These doors together with others of the same design were later moved to the lower levels served by sub vertical shafts. In addition, doors to prevent flood water entering the pump chambers on 18 level were installed at each end of that level, and designed for a head of 360 feet so that water would have to reach 16 level before the pumps were flooded. All these doors were called upon to hold water and it is reported that only a small plug in one of the doors and a 4 in. dia flanged pipe joint failed. The lesson is that in these cases the smallest details warrant as much attention as the major ones. That these were the only equipment failures when so much depended on equipment, is very much to the credit of design engineers, both of the Gold Fields head office and companies who supplied both mechanical and electrical equipment. Until I had read the paper I wondered why the policy of isolation by bulk head doors was not continued as the development moved eastward towards the Bank Compartment and particularly when it pierced the Bank dyke. The reasons have been given in the paper. It was unreasonable to expect provisions to be made to counter the remote contingency that the large installed pumping capacity and mine capacity to store water would be exceeded during a peak inrush. When pumps were being considered for West Driefontein, it was decided that the Gold Fields standard underground main pumps at that time of 1 million gallons per 24 hours would be too small. Three alternatives were considered. 1. Very large units that would require underground sub assembly and dismantling of both pump and motor. 2. The largest pump and motor that could be conveyed as a complete pump or motor from surface to the pump chamber. 3. Pumps of higher speed to reduce dimensions and weight. It was decided to adopt alternate 2 because of avoidance of transporting pumps in parts and assembling underground. Alternative 3 was not favoured because high speeds would have introduced problems of more exact rotor balancing. I believe the decision was correct and in the crisis enabled comparative easy transport of pumps and motors to surface for overhaul and, if required, transfer to other pump stations. The standard pump thus became a 10 stage 1,500 rpm pump with a capacity of approximately 2 million gallons per 24 hours against a static head that varied

Jan 3, 1969

By J. Svoboda, W. J. C. Venter, R. N. Guest

SYNOPSIS Wet high-intensity magnetic separation was examined as a method for the recovery of copper and lead from Tsumeb flotation tailings. Bench-scale and pilot-plant tests were conducted and, despite the very low magnetic susceptibilities of all the complex copper and lead minerals, copper and lead recoveries of over 60 per cent and almost 50 per cent respectively were obtained at a combined copper and lead grade of up to 13,5 per cent. The recoveries were found to be practically independent of magnetic induction in the range 0,5 to 2,2 T, and the grade of the magnetic concentrate decreased with increasing magnetic induction. The grade of the magnetic concen¬trate improved when the flowrate of the slurry was increased, and desliming was found to have a profound effect on the. metallurgical process. Particles smaller than 10 µm were not recovered, and their presence in inefficiently deslimed samples impaired the overall performance of the magnetic separation

Jan 1, 1988

By S. K. Mahata, P. G. Suresh Kumar, B. B. Singh

Improvement of post tap hole practices is achievable by mechanized handling of melt during the production of Ferro Chrome, resulting in higher recovery of chromium. The paper deals with modern practices adopted in the production of ferro-chrome since past two decades. The methods and practices deal with various areas : a) Improved method of operating the tap hole by selection of right quality of refractory to maintain the life of tap hole. b) Collection of melt in different types of receptacles like refractory brick lined mild steel ladles, cast steel ladles, cast iron pans being chosen for cost effective and efficient handling. c) Separation of slag and metal, casting of metal, crushing, sizing and stock piling etc. d) Slag disposal and recovery of entrapped metal. The drive behind the above development is continuous improvement, which results in higher chromium recovery and reduces loss of metal in slag by completely mechanized method so as to be at the same level with producers of ferro-chrome in other advanced countries , in the emerging global economy.

Jan 1, 2007

Rock fall accidents continue to be the main causes of fatalities in the mining industry. The occurrence of rock falls in supported stopes implies a failure of the support system. The failure of the support system in turn implies a failure in design. In this paper, ethical issues associated with engineering design are discussed, with particular relevance to stope support design. A risk approach is introduced that will allow designs to be carried out that are compatible with the acceptable risk defined by the mining company management. The implementation of this approach would overcome the ethical shortcomings of current support design practices.

Jan 1, 2007

By L. A. Maseko

"As part of the mining engineering curriculum, students are required to be placed in industry for vacation work or work-integrated learning (WIL). In this paper we review work-based placement as done at the four South African mining schools: the University of Johannesburg, the University of Pretoria, the University of the Witwatersrand, and the University of South Africa.Key aspects of past and current WIL (pre- and post-graduation) practices that may need attention are highlighted for consideration by all universities that provide professional qualifications. Work-directed theoretical learning, problem-based learning, project-based learning, workplace learning, and simulated work experiences are discussed as legitimate approaches to WIL.Regardless of the choice each institution makes, commitments of universities, preparedness of university teachers, and the desire for equity and excellence will play an important role in the provision of WIL.DefinitionsAccredited Qualification: a qualification awarded on successful completion of an accredited programme.Advisory Boards (or Committees): are essential infrastructure for a WIL curriculum that is built on the integration of the workplace and the university. This requires the collaboration of experts from both environments. Workplace advisors are critical to the success of the academy as they embody expert knowledge of the ‘real world’.Assessment: the process of determining the capability or competence of an individual against standards by evaluating performance.Category: a mode of registration defined in or under the ECSA Act which has a distinctive purpose, characteristic competencies, defined principal routes to registration, and educational requirements.Experiential learning: (in South Africa sometimes used synonymously with work placement or cooperative education) is a term used with a great variety of meanings in the international literature. More broadly, it may refer to learning that has meaningful learner involvement. It is the process of generating meaning from direct experience. In the international literature, experiential learning is learning through reflection on doing, which is often contrasted with rote or didactic learning."

Dec 1, 2018

By T. K. Roy

INFACON XI has no doubt earned the distinction as the first such Congress in India. This prestigious occasion could become a reality of a long cherished dream of the Indian Ferroalloy Producers, consumers and ex-porters. The International Committee of Ferro Alloys (ICFA), South Africa, the august body for organising INFACON, every three years, could be convinced by the Indian Ferro Alloy Producers? Association (IFAPA) to award INFACON (XI) to India. This Congresss, organized by IFAPA, has opened a window for the Ferroalloy Community of India, the up-coming Asian Tiger, to register their strength and weakness to the world forum with the principal objectives of evolving long and short-term optimum road-maps for development. It is to be reckoned that India is poised to be a steel giant by 2020 when it is envisaged that the steel production may reach a level of 120 million tons of which significant proportion has to be in the categories of alloy and special steels, requiring standard and high grade ferroalloys. Keeping the above objective in view, the theme of this Congress has been rightfully designed as ?Innovations in Ferro Alloy Industry.? This Congress has also earned a distinction of more than eighty papers, finally selected for inclusion in the Proceedings. More than 100 internationally and nationally reputed experts in the field of ferroalloys (technology and manufacturing practices as well as world scenario) have been approached for critical review of abstracts and selection for the proceedings. It needs to be mentioned without the cooperation received from ICFA the high standard of INFACON could not have been assured. The papers are suitably grouped under seventeen heads, starting from world situation to production and operation followed by present and future technologies and finally to modelling and simulation. It is a Herculean task to the Technical Committee to fit these papers in proper sequence. The Commit-tee members kept no stone unturned to ensure the cogency with the subject matters and at the same timekeeping the flexibility of interests of the participant, especially in the context of three parallel sessions. The Proceedings containing only refereed papers of high quality, will serve the entire gamut of ferroalloy industry and will also highlight the present status of concerned countries. The areas of attention to make the industries globally competitive and at the same time laying emphasis on the prevailing practices, will help the industry leaders to formulate an appropriate global approach. Following the break-through step, instilled by INFACON XI, the Proceedings will be available both in bound and in searchable electronic CD-ROM format. I, as the Chairman of the Technical Committee would like to express thanks and high appreciation to all the Committee members for their whole hearted efforts in all respects without which it would not have been possible to complete these proceedings in the scheduled time. Technical Committee desires to place on record their gratitude to Organising Committee for their synergic cooperation all through in successfully executing multifarious tasks, associated with such a grand international technical Congress.

Jan 1, 2007

By J. Hadjigeorgiou, G. Knox

Since their introduction in 2010, paddled energy-absorbing rockbolts have been widely used in seismically active hard rock mines. This paper provides new data and reviews previous work to quantify the performance of paddled energy-absorbing rockbolts under controlled laboratory conditions. Of significance is the realization that the typical split location in impact tests, at the centre between two paddle anchor points can at best provide an upper limit value. This inherent variability in performance under different testing configurations should be acknowledged and taken into consideration in the design of ground support in seismic conditions. This paper discusses the reduction in capacity of paddled rockbolts as a function of loading angle from a maximum value during axial tests (0° loading angle) to the lowest value during pure shear (loading angle of 90°). A significant reduction in displacement capacity is observed as the loading angle changes between axial (0°) and 40°. Beyond a 40° loading angle up to shear (90°) loading the reduction in displacement capacity is less significant. Due to the variances in the capacity observed through the variance of the testing configuration: loading mechanism, direction of loading, location / presence of a discontinuity, it must be recognized that results from laboratory-based testing are not independent of the testing configuration. This should be acknowledged when extrapolating anticipated performance in the field.

Oct 9, 2024

By Y. C. Kim

The estimation of local recoverable reserves using the widely spaced exploration drill hole information in an open-pit mine is probably one of the most difficult tasks in ore reserve estimation. The difficulty of this problem is magnified if the grade distribution is highly skewed, such as in a gold deposit. This paper describes the results of performance comparison of three different kriging techniques in an open-pit gold - silver deposit. The three different kriging techniques compared in their local recoverable reserve estimation capabilities are: (1) lognormal kriging, (2) indicator kriging, and (3) probability kriging. For performance comparison, the predictions are compared with the actual recoverable reserves determined from blast hole information. Based on the results from one test bench, both indicator and probability kriging performed better than lognormal kriging, perhaps owing to samples not being truly lognormal. Between indicator and probability kriging, probability kriging results were definitely superior to indicator kriging results.

Jan 1, 1987

By P. Beukes, D. Bessinger, R. Glenewinkel

High titania slag is produced by the smelting of ilmenite and a suitable carbonaceous reductant in electric furnaces. Currently liquid slag is cast into large blocks, which take about 10 days to cool down before they can be crushed, milled and classified into two final products. The two products, chloride and sulphate grade slag, are differentiated according to their size. Granulation of titania slag has been identified as a possible alternative to the conventional block route. This paper discusses some of the work carried out at Exxaro Research and Development to investigate both wet and dry granulation of titania slag.

Jan 1, 2007