Search Documents

By B. P. Watson

The discussion written by Dr de Frey suggests that mine design should be based on closely spaced stability pillars. However, this concept leads to low extraction ratios at depth. The concept of `crush' pillars in conjunction with more widely, appropriately spaced stability pillars allows for significantly larger extraction ratios, particularly at depth. It should be noted that the rock conditions in many areas of South African platinum and gold mines are good, allowing significant spans to be mined safely between stability pillars. `Crush' pillars are cut small enough to fail stably near the face under stiff loading conditions, and their residual strength is intended to support about 10 m rock height between stability pillars. While this support resistance cannot be achieved by conventional support, crush pillars have been proven to have the required capacity for this purpose. The concept of leaving smaller crush pillars with appropriately positioned stability pillars has been used successfully for more than 30 years in areas of South African platinum and gold mines.

Jan 1, 2011

By J. Hadjigeorgiou, G. Knox

Since their introduction in 2010, paddled energy-absorbing rockbolts have been widely used in seismically active hard rock mines. This paper provides new data and reviews previous work to quantify the performance of paddled energy-absorbing rockbolts under controlled laboratory conditions. Of significance is the realization that the typical split location in impact tests, at the centre between two paddle anchor points can at best provide an upper limit value. This inherent variability in performance under different testing configurations should be acknowledged and taken into consideration in the design of ground support in seismic conditions. This paper discusses the reduction in capacity of paddled rockbolts as a function of loading angle from a maximum value during axial tests (0° loading angle) to the lowest value during pure shear (loading angle of 90°). A significant reduction in displacement capacity is observed as the loading angle changes between axial (0°) and 40°. Beyond a 40° loading angle up to shear (90°) loading the reduction in displacement capacity is less significant. Due to the variances in the capacity observed through the variance of the testing configuration: loading mechanism, direction of loading, location / presence of a discontinuity, it must be recognized that results from laboratory-based testing are not independent of the testing configuration. This should be acknowledged when extrapolating anticipated performance in the field.

Oct 9, 2024

By Y. C. Kim

The estimation of local recoverable reserves using the widely spaced exploration drill hole information in an open-pit mine is probably one of the most difficult tasks in ore reserve estimation. The difficulty of this problem is magnified if the grade distribution is highly skewed, such as in a gold deposit. This paper describes the results of performance comparison of three different kriging techniques in an open-pit gold - silver deposit. The three different kriging techniques compared in their local recoverable reserve estimation capabilities are: (1) lognormal kriging, (2) indicator kriging, and (3) probability kriging. For performance comparison, the predictions are compared with the actual recoverable reserves determined from blast hole information. Based on the results from one test bench, both indicator and probability kriging performed better than lognormal kriging, perhaps owing to samples not being truly lognormal. Between indicator and probability kriging, probability kriging results were definitely superior to indicator kriging results.

Jan 1, 1987

By P. Beukes, D. Bessinger, R. Glenewinkel

High titania slag is produced by the smelting of ilmenite and a suitable carbonaceous reductant in electric furnaces. Currently liquid slag is cast into large blocks, which take about 10 days to cool down before they can be crushed, milled and classified into two final products. The two products, chloride and sulphate grade slag, are differentiated according to their size. Granulation of titania slag has been identified as a possible alternative to the conventional block route. This paper discusses some of the work carried out at Exxaro Research and Development to investigate both wet and dry granulation of titania slag.

Jan 1, 2007

By J. Abdollahisharif

Optimal cut-off grade is one of the most critical parameters in open-pit mine design because it defines the ore and waste and thus determines the maximum net present value possible from the mining operation. Although the algorithm presented by Lane (Choosing the optimum cut-off grade. Colorado school of Mines Quarterly, vol. 59, no. 4, 1964. pp. 811-829) is the most common one in the literature, it does assume constant capacities of the mine, processing, and refinery. In this paper, Lane's original algorithm has been modified to consider variable processing capacities in order to determine the optimal cut-off grade in open-pit mines. The new algorithm proposed here is compared to both Lane's original algorithm and to a previous modification that incorporated rehabilitation costs into the cut-off grade estimation. The algorithm proposed here that permits variable processing capacities is shown to be superior for the determination of optimal cut-off grade to both these previous versions. In addition, a computer-based program was developed in Microsoft Office Excel© to calculate the optimal cut-off grade as proposed here.

Jan 1, 2012

By R. R. M. Cousens, W. S. Garrett

Discussion: L. T. Campbell Pitt: When Mr Garrett and I discussed the design and construction of plugs and bulk head doors to resist great water pressures in mines about ten years ago, we visualized an emeregeny when there would be no time for site preparation. We could not however, anticipate a problem of such magnitude and urgency as the one described in the paper under discussion. The paper very clearly describes the flooding and the measures taken to save the mine. The complete flooding would have been a national disaster. The account of the combat between man and water reads like the account of a military operation. It was an endeavour which achieved success because there was a master plan, tenacity and, in fact, heroism. The paper is of necessity a long one. In my contribution I will mention some historical facts and factors that I believe have relevance to the flooding and the saving of the mine. It is of great satisfaction to me to have been one of the two initiators of a new approach to underground plug design and construction. The investigation was taken over by a Chamber of Mines Committee which combined our early work with further research and the resulting data had a significant bearing on the West Drie emergency plug designs. The final plug length was correctly based on the requirements to obviate leakage. A plug to have structural strength only would have been very much shorter but so ineffective as to have become a waste of labour, material, and in consequence, wasted the limited time available to prevent flooding of the whole mine. The figure of 75 lb per sq in. sheer stress provided a very ample margin, in my opinion, but under the very difficult site conditions and the limitations of plug material suitable for the very unusual construction, justified such a figure. There must have been considerable temptation to reduce the safety margin due to the urgency to complete and commission the plugs, but it is much to the credit of the directors of this operation that nothing less than a safe design was permitted. In about 1945 Blyvooruitzicht Gold Mining Company, which was then mining in to the West Driefontein area to assist in early development, decided to protect themselves from a possible inrush of water from the latter mine. A bulk head door was accordingly designed and installed on 2 level between 1945 and 1948 at 4,218 ft below surface. Since West Driefontein paid for it, Gold Fields consulting mechanical engineers collaborated with their colleagues of Rand Mines who completed their design after a few modifications were agreed. This door was never used to prevent an inrush into Blyvooruitzicht but the exercise was very useful to Gold Fields when the high pressure doors initially installed on 10 and 12 levels between Nos. 2 and 3 shafts to enable isolation of one section of the mine from another were designed. At that time the capacity of West Driefontein to cope with an inrush of water was comparatively small because the storage in stoped areas and the installed pump capacity were much less than in later years. These doors together with others of the same design were later moved to the lower levels served by sub vertical shafts. In addition, doors to prevent flood water entering the pump chambers on 18 level were installed at each end of that level, and designed for a head of 360 feet so that water would have to reach 16 level before the pumps were flooded. All these doors were called upon to hold water and it is reported that only a small plug in one of the doors and a 4 in. dia flanged pipe joint failed. The lesson is that in these cases the smallest details warrant as much attention as the major ones. That these were the only equipment failures when so much depended on equipment, is very much to the credit of design engineers, both of the Gold Fields head office and companies who supplied both mechanical and electrical equipment. Until I had read the paper I wondered why the policy of isolation by bulk head doors was not continued as the development moved eastward towards the Bank Compartment and particularly when it pierced the Bank dyke. The reasons have been given in the paper. It was unreasonable to expect provisions to be made to counter the remote contingency that the large installed pumping capacity and mine capacity to store water would be exceeded during a peak inrush. When pumps were being considered for West Driefontein, it was decided that the Gold Fields standard underground main pumps at that time of 1 million gallons per 24 hours would be too small. Three alternatives were considered. 1. Very large units that would require underground sub assembly and dismantling of both pump and motor. 2. The largest pump and motor that could be conveyed as a complete pump or motor from surface to the pump chamber. 3. Pumps of higher speed to reduce dimensions and weight. It was decided to adopt alternate 2 because of avoidance of transporting pumps in parts and assembling underground. Alternative 3 was not favoured because high speeds would have introduced problems of more exact rotor balancing. I believe the decision was correct and in the crisis enabled comparative easy transport of pumps and motors to surface for overhaul and, if required, transfer to other pump stations. The standard pump thus became a 10 stage 1,500 rpm pump with a capacity of approximately 2 million gallons per 24 hours against a static head that varied

Jan 3, 1969

By R. Haldenwang, R. Erasmus, P. T. Slatter, R. P. Chhabra

Notches are used routinely for measuring the flow rate of water with free surface flows. As far as can be ascertained, no work has been done to investigate the performance of these flow rate measurement devices for non-Newtonian suspensions. The Flow Process Research Centre at the Cape Peninsula University of Technology has investigated the flow rate of kaolin and bentonite suspensions from a tank for two notch shapes, namely rectangular and triangular, and for 3 different concentrations of each suspension. The notches were calibrated using water and then the kaolin and bentonite suspensions were tested in them. The rheological characterisation of the fluids was done with a Paar Physica MC-1 rotary viscometer fitted with a cup and roughened bob. Analysis of the results shows a significant increase in discharge coefficient with increase in concentration, and the discharge coefficient has been correlated to the yield stress. This is the first such study, and further investigation is needed to confirm and extend these findings.

Jan 1, 2007

By J. Svoboda, W. J. C. Venter, R. N. Guest

SYNOPSIS Wet high-intensity magnetic separation was examined as a method for the recovery of copper and lead from Tsumeb flotation tailings. Bench-scale and pilot-plant tests were conducted and, despite the very low magnetic susceptibilities of all the complex copper and lead minerals, copper and lead recoveries of over 60 per cent and almost 50 per cent respectively were obtained at a combined copper and lead grade of up to 13,5 per cent. The recoveries were found to be practically independent of magnetic induction in the range 0,5 to 2,2 T, and the grade of the magnetic concentrate decreased with increasing magnetic induction. The grade of the magnetic concen¬trate improved when the flowrate of the slurry was increased, and desliming was found to have a profound effect on the. metallurgical process. Particles smaller than 10 µm were not recovered, and their presence in inefficiently deslimed samples impaired the overall performance of the magnetic separation

Jan 1, 1988

By L. A. Abichequer

ROM grade variability is one of the most important factors influencing plant product recovery. Due to the influence of grade variability on mine profits, it is deemed important to guarantee a proper homogenization of the ore through a well-planned blending and homogenization pile system from which the ore is reclaimed at an acceptable grade fluctuation. This study tests geostatistical simulation efficiency in predicting in situ grade variability. The methodology is illustrated using a data-set from a large phosphate mine in central Brazil. Additionally, real data obtained at the mine site during January and February 2007 were used to derive the actual grades of each pile formed during this period. Each pile was formed by a selection of blocks within a dig line and these lines mined along the year 2007 were also made available. Given the real grades, it was possible to reconciliate and validate the results predicted by the proposed methodology. The main outcome of this study is the opportunity to check the geostatistical simulation as a tool to quantify the variability of the homogenization system.

Jan 1, 2009

By A. Doroudgar, H. Noferesti

Unstable rock failure or rock bursting is one of the most dangerous problems in deep hard rock mines. This type of failure, that occurs uncontrollably, is associated with a significant release of strain energy from the surrounding rock. In this study, the numerical simulation of unstable rock failure was carried out using the three-dimensional explicit Lagranian finite-volume finite difference method to identify the onset and location of unstable failure events in the model. On this basis, a numerical simulation of mine pillars with width-to-height ratios of 0.5, 2 and 3 was performed. A criterion was developed, based on the calculation of the elastic strain energy, to determine the prone areas for the initiation of rockburst in the models. The results of this study showed that, in softer loading systems, due to large amounts of stored elastic strain energy, an unstable equilibrium is established, which leads to the rapid transfer of strain energy to the rock in the form of violent failure. It was also found that the unstable failure starts at the corners and free surface of the model. The new criterion developed in this study may help predict the occurrence of rockbursts in slender pillars and the design of pillars to control human and financial losses caused by this phenomenon.

Nov 27, 2024

By C. Botha

The South African democratically-elected government instituted policies and legislation that are intended to bring about change and transformation in the country and have drastically affected different industries, among others, the mining industry. The Mineral and Petroleum Resources Development Act 28 of 2002 (MPRDA) and the Broad-based Socio-economic Empowerment Charter (Mining Charter) were introduced in order to redress previous inequalities and to promote women?s employment in the mining industry. This research evaluates the practical implementation of the MPRDA and the Mining Charter with specific reference to women in underground mining. A quantitative research paradigm was used. Data were collected through a process of a face-to-face interview surveys utilizing a structured questionnaire. The research setting was limited to the platinum-mining industry in the area of Rustenburg in the North West Province. The study population consisted of 195 available women working undergound at the mine. It is clear from the findings that mining companies are facing major challenges in their attempt to incorporate women in underground mining activities. Company policies regarding these issues must be firmly in place; however, the challenge lies in the translation of these policies into practice. In this regard, managers will have to play a leading role in the successful phasing in of women into the underground mining arena.

Jan 1, 2012

By Q. Fu, Q. Wang, L. G. Wen, M. X. Jia, J. J. Zhao, J. W. Zhou

The BGRIMM process mineralogy analyser (BPMA) is a new automated mineralogy software platform developed in China. This system consists of the BPMA software platform, controlling a combination of commercially available scanning electron microscopy (SEM) and energy dispersive Xray spectrometry (EDS). The BPMA software controls SEM and EDS through their application programming interfaces, to form an auto-SEM and EDS system that automatically acquires BSE images and X-ray spectra, respectively, and classifies minerals by spectrum-matching. After automated measurement and mineral identification, various quantitative process mineralogical data (e.g., mineral composition, mineral abundance, mineral liberation and intergrowth relationships, mineral associations, particle and grain sizes, particle density distributions, calculated assay, elemental deportments, mineral grade recovery and elemental grade recovery, etc.) would be calculated quickly, accurately and automatically. The BPMA could be used for ore characterisation as a new advanced automated mineralogy technology. Keywords: BSE image; X-ray spectrum; automated mineral identification; quantitative mineralogical investigation; automated mineralogy

Jan 1, 2020

By S. Konetschnik, E. Dreyer, A. Filzwieser

"More intense furnace operations require effective cooling in order to achieve low refractory wear and good furnace lifetimes, making cooling technology an important aspect of furnace operations. However, the use of water - today’s standard cooling medium - has some disadvantages, as it can cause problems both during furnace start-up and operation, namely hydration problems, corrosion, and explosions. Apart from these aspects, the energy that is removed by extensive cooling cannot be recovered and is normally lost in the cooling towers.With METTOP’s new patented cooling technology it is possible to overcome the disadvantages of water by using an alternative cooling medium, namely ionic liquids (ILs). The main advantage of ILs is the fact that there is no risk of explosion should this liquid come in contact with molten metal. Furthermore, ILs can be used at higher temperatures than water - up to 200°C. This relatively high cooling medium temperature avoids hydration and corrosion problems and allows recovery of the energy by combining the ILTEC system and the organic Rankine Cycle (ORC) technology, for example.Due to the removal of the explosion risk, much higher safety standards can be achieved, particularly in critical areas such as tap-holes"

Jan 1, 2014

By T. C. Huber

The southern African region has a high concentration of mineral resources and supplies much of the world?s platinum demand. As a result, the international community watches South Africa to understand the impact of supply on global markets. An analysis of supply certainty and risk plays a key role in the future of growing demand in various sectors. The southern African platinum industry experienced substantial growth in the early part of the 21st century, resulting in bullish forecasts for growth during the period of 2000?2006. However, southern African platinum producers saw a significant drop in production over the following three years as a result of many dynamic factors in operations and the global economy. Between 2006 and 2009 there was a million-ounce shortfall between forecast and actual production. This was raised as a concern at the Fourth International Platinum Conference in 2010 by Stephen Forrest during his keynote address, specifically regarding the lack of understanding in the market of the causes of this shortfall and any action that was being taken to address them. This paper reviews publicly available information in the media and corporate reports and communications for the period January 2006 to December 2009. In addition, several interviews were held with key stakeholders in the industry to provide further perspective. The paper then highlights the main reasons that are reported to have affected the loss in production over the period and discusses the possible implications of the information that the mining industry does and does not disclose regarding platinum supply.

Jan 1, 2012

By D. F. Malan, J. A. L. Napier

A number of shallow coal or hard rock mines employ pillar mining systems as a strategy for roof failure control. In certain platinum mine layouts, pillars are designed to ‘crush’ in a stable manner as they become loaded in the panel back area. The correct sizing of pillars demands some knowledge of the pillar strength and the overall layout stress distribution. It is particularly important to understand the impact of the layout geometry on the effective regional ‘stiffness’ of the rock mass around each pillar. An important design strategy is to model relatively detailed layout configurations which include a precise representation of the local pillar layout geometry and to analyse multiple mining scenarios and extraction sequences to select optimal pillar sizes and barrier pillar spacing. Although computational solution techniques are now impressive in terms of run time efficiency, a major difficulty is often encountered in assigning suitable material properties to the pillars and in devising an effective material description of the layered rock strata overlying the mine excavations. This paper outlines an efficient numerical strategy that can be used to assess large-scale pillar layout performance while retaining the ability to modify individual pillar constitutive behaviour. The proposed method is applied to selected layouts to compare estimated average pillar stress values against values determined by detailed modelling and against observed behaviour.

May 3, 2023

By J. Gholamnejad

Determination of the optimum production schedules over the life of a mine is a critical mechanism in open pit mine planning procedures. Long-term production scheduling is used to maximize the net present value of the project under technical, financial, and environmental constraints. Mathematical programming models are well suited for optimizing long-term production schedules of open pit mines. There are two approaches to solving long-term production problems: deterministic- and uncertainty- based approaches. Deterministic-based models are unable to deal with grade and geological uncertainties, which are two important sources of risk in mining industries. This may lead to discrepancies between actual production obtained by these algorithms and planning expectations. In this paper, a new binary integer programming model was developed for long-term production scheduling that incorporates geological uncertainty within the orebody. Then, traditional and uncertainty-based models are applied to an iron ore deposit. Results showed that the uncertainty-based approach yields more practical schedules than traditional approaches in terms of production targets.

Jan 1, 2012

By A. Lane

The socio economic risks of mining in South Africa have been emerging for some time now, and have been brought into sharp relief by recent events in the platinum sector. The slow pace of social upliftment in the country has lead to widespread social unrest with consequent calls for different forms of resource nationalism. Fundamentally, the key stakeholders are not fully aligned, and are not engaging productively. This poses significant above-the-ground risk to mining companies. Measuring social impact, deploying inclusive solutions and engaging effectively with stakeholders are three ways in which mining companies can mitigate this risk.

Jan 1, 2012

By N. Patel

Many factors, from engineering and design to supply, installation, and operation affect the service lifespan of cast refractory linings. If a shortcoming occurs at any of these stages, the lining lifespan can be drastically reduced. Although not every aspect that can affect a cast refractory lining?s lifespan is outlined here, a few key points are highlighted, with an emphasis on the various installation parameters. Keywords cast linings, refractory lifespan, lining engineering and design, lining supply, lining installation, curing, dry-out.

Aug 1, 2013

By C. Birch, M. Katuruza

"The purpose of this study was to demonstrate unmanned aircraft system (UAS) technology in opencast highwall mapping using the experience at Isibonelo Colliery in Mpumalanga Province of South Africa. In opencast mines, geological mapping has evolved over time and there have been challenges in extracting valuable information from exposed highwalls due to restricted access for safety reasons. A UAS was used at Isibonelo Colliery to conduct highwall mapping, using drone-based digital photogrammetry techniques. A demonstration survey was undertaken during February 2018. The highwall flyover demonstration was planned for two areas (North and South pits) where field control points were placed by the mine survey department. A contractor used a DJI Phantom 4 (Pro) for the highwall mapping. Raw data was processed within 48 hours and a 3D model of the mapped pit area was produced. Further data extraction included obtaining updated weathering and lithological contact elevations and thicknesses for use in short-term planning. The results showed a good correlation between the resource model and the UAS data model. The project was considered a success and highwall flyover mapping and is now standard practice at Isibonelo Colliery.IntroductionDetailed geological mapping is crucial to the understanding of the structure of any mineral deposit. Several mapping methods may be applied depending on the available exposure/outcrop and nature of the orebody; for example, coal deposits typically suboutcrop only, therefore an opencut highwall provides the best exposure for mapping the geology. Mapped information, when incorporated into a resource model (generated from exploration borehole data), improves the understanding of the orebody or coal seam. This research paper focused on the use of unmanned aircraft system (UAS) technology for pit highwall mapping to generate data for updating geological models and avail the latest information to mine planning to improve the short-term plans."

Mar 1, 2019

By I. C. R. Gilchrist

A principal requirement in the design of a backfill transportation pipeline is the accurate prediction of the values of key slurry flow parameters. Input variables, such as particle size and solids concentration, are usually determined by the load-bearing requirements of the placed fill. It is therefore necessary to identify the optimum conditions of transport for a particular combination of input variables. This paper critically reviews the methods available to predict the values of flow parameters in slurry pipeline systems in the light of experimental data generated at a test facility. Particular reference is made to rod milled waste and deslimed tailings transport systems and, in the case of the former, it is shown that both pumping and load-bearing requirements can be optimized.

Jan 1, 1988