Search Documents

By B. P. Watson

In South Africa, the Bushveld platinum group metal deposits are unique in that they are the largest platinum group metal deposits in the world. These deposits occur as two distinct stratiform tabular orebodies and strike for many hundreds of kilometres. Mining is extensive, with depths ranging from close-to-surface to 2 000 m. The mining method is a variation of planar open stoping. Pillars are widely used to support the open stopes. Crush pillars are commonly used in this role, where the residual pillar strength provides the required support resistance to stabilize the stoping excavations. This paper describes the direct measurement of stress within these crush pillars, and describes the stress?strain behaviour of these pillars. These findings indicate that the measured pillar failure stress is too high. The implications of these findings are that roof damage and pillar bursting could occur, and some examples of this type of damage are shown. The paper concludes that this problem could be mitigated if the three dimensional pillar geometry were modified and the pillars were cut smaller.

Jan 1, 2007

By T. Tamenti

The purpose of the project was to conduct a feasibility study to determine if the current operating bottom dump trucks that haul coal should be replaced with rear dump trucks. The engineering availability of the bottom dump trucks was lower than targeted while the operating costs are the highest of all coal haulers within the Anglo Coal opencasts. To determine if it is feasible to replace the current bottom dump trucks with rear dump trucks, a production profile simulation was conducted to determine the number of rear dump trucks that would be required to meet the annual coal hauling requirements. The total capital and operating costs of these rear dump trucks were also determined using a total cost of ownership model. These were compared with the current costs of the bottom dump trucks to determine if it is financially feasible to replace the bottom dump trucks with rear dump trucks. Having considered the capital outlay that would be required to replace the bottom dump trucks with rear dump trucks as well as their respective operating costs, it was concluded that the current bottom dump trucks should be replaced with rear dump trucks. Other factors were considered in coming to this conclusion.

Jan 1, 2007

By M. M. Ali, C. Musingwini, R. A. Phillips

The long-term open-pit mine production scheduling problem (OPMPSP) is typically solved in two broad stages. The first stage entails optimisation of the ultimate pit limit, which delimits the economical final pit and maximises the undiscounted value of the deposit. The second stage entails optimisation of the long-term open-pit mine production scheduling, which maximises the discounted value of the deposit. The long-term OPMPSP is a type of an NP-hard problem, such as the travelling salesman problem (TSP), because it is intrinsically complex to solve since it incorporates both hard and soft constraints. Therefore, metaheuristic approaches have been used to find global optimum solutions to the long-term OPMPSP. This paper presents a metaheuristic approach utilising a dual interchange algorithm (DIA) to solve the long-term OPMPSP. The DIA is a parent algorithm which supervises two subservient algorithms, namely, simulated annealing (SA) and Tabu search (TS). The DIA selects the better solution generated in each run from the two algorithms, and simultaneously penalises the algorithm that produced an inferior solution, while rewarding the one that produced a better solution. The DIA was tested on the three-dimensional Arizona Copper Deposit (KD) dataset, which is publicly available for research purposes from the online MineLib repository. It was set to generate net present values (NPVs) in five-minute intervals and the solution improved until it plateaued at about 30 minutes of runtime. The NPVs compared favourably to those obtained on the same KD dataset but obtained over 24-hour runtimes, when solved using simulated annealing and Tabu search algorithms, and the NPV generated from the work of Muñoz (2012) using the modified TopoSort as found on the MineLib repository at the time of this study. Therefore, this paper demonstrates that DIAs can be developed and used to solve the three-dimensional long-term OPMPSP.

Sep 1, 2021

By F. Smit

Mining and plant practices can benefit from preconcentration of UG2 platinum ores in a dense medium separation (DMS) plant. The main benefit of DMS is the selective discard of waste from the feed stream, thus improving project economics while reducing the power and water requirements for processing. On the mining side, with the correct combination of variables, implementing DMS as a pre-concentration step can reduce cut-off grades and, as a result, increase ore reserves. In addition, the use of DMS technology gives the mine team the opportunity to consider alternative mining methods for an operation. The challenges of balancing the mining tonnage, methods, and resulting grades with the process plant size, recoveries, and DMS discard volumes have resulted in the development of a model to optimize value on new projects or existing operations. This paper will focus on these benefits from a mining and plant perspective, quantifying the water and power savings, and look at the economic benefits of preconcentration and the effect of metal prices, plant feed grade, and DMS efficiency in different mining environments.

Jan 1, 2013

By S. Michael, T. E. Moongo

Electrowinning consumes a substantial amount of electrical energy, and owing to the ever-increasing unit cost of electrical power there is a need to improve current efficiency in the process. This research was carried out to design a continuous quality improvement framework for improving electrowinning current efficiency by applying statistical process control (SPC) on an online industrial copper electrowinning operation. A sequential mixed research methodology was applied and a statistical software package utilized for analysing data. It was concluded that metallurgical short-circuits (hotspots) had the most significant effect on current efficiency. Bringing hotspots under statistical control resulted in a 5.40% improvement in current efficiency, which is equivalent to approximately 74 t of 99.999% pure grade A copper cathode production over a period of 1.5 months.

Jan 1, 2021

By W. C. Joughin

A risk evaluation model has been developed, that enables the quantification of expected injuries and economic losses resulting from rockfalls associated with a support system in a given geotechnical environment. This enables the comparison of different support systems based on the expected frequency of injuries and the total cost of the support system, including the expected economic losses. The model takes into consideration the variability in joint orientations and joint strength within the geotechnical environment and the variability and quality of support systems. The quantification of the benefits of other rockfall risk-mitigating strategies, such as the effectiveness of barring or monitoring, are also incorporated in the model. The risk model is described in this paper and the validation of the model and case studies are described in Part II.

Jan 1, 2012

The Barrick North Mara Mine and the Advanced Systems Group at SGS Minerals collaborated on the implementation of a grinding expert system for the control and optimisation of a single semi autogenous (SAG) mill. Over the last 5 years, grinding expert control has gained wide acceptance by mineral processors. In this paper, two key factors for success are highlighted: the adaptability of the software tools and the interaction with site personnel. Created with SGS?s MET expert console (MEC) toolkit, and running on Gensym?s G2 real time inference software, the North Mara expert logic has been set up to keep a steady and on spec leaching feed slurry while striving to maximize throughput. Leach feed stability was achieved by standardizing operating practices across shifts; a result of successful collaboration with site personnel in developing a consistent control strategy. The strategy maintains the SAG load and power draw in an optimised range by manipulating SAG feed rates and inlet water flow. The project life-cycle was slightly longer than average due to site specific constraints. One of these was the high turnover rate of site?s workforce during the project, coupled with the availability of key staff on site due to the fly in fly out work roster. These constraints called for different, and innovative ways of project commissioning and hand-over. This paper describes details of the control solution, its implementation as well as results and conclusions.

Jan 1, 2009

By A. F. Mulaba-Bafubiandi

Pseudomonas spp was isolated from mine water and tailings samples collected from mining effluents and mine dumps in the Gauteng and Northern provinces of South Africa respectively. Adsorption properties of Pseudomonas spp were then tested for the removal of Cu and Co initially from their synthetic sulphate solutions, subsequently from effluents derived from metallurgical operations. The effects of experimental conditions such as pH, temperature, time, volume and metal concentration on the efficiency of the biosorption process were studied. Absorption of 45% Cu (pH 6, 37°C, 24 hours) and 40% Co (pH 6, 37°C, 24 hours) was observed from solutions with low concentrations (0.07 M). A maximum of 73% and 65% of Cu and Corespectively were recovered from the mine water samples derived from effluents.

Jan 1, 2009

By K. Moxham, B. McKeown

The South African gold and platinum deposits were formed in very different ways and yet both have many similarities. They are flat dipping tabular orebodies, extremely narrow and located in hard abrasive country rock. The mining methods employed are also similar. Primary access is via shafts or declines; secondary access is via haulages and cross-cuts; and tertiary access is from raises. The proposed solution for rapid access described in this paper is focused on the haulages and cross-cuts.

Jan 1, 2006

By P. A. P. Fouché

Processing confidence for a bankable feasibility study on a green field heavy mineral deposit is inmost cases achieved only through bulk sample processing. Bulk sample is classified as a large enough concentrate sample that is processed into final products to satisfy market sample demand as well as further processing demands such as smelting. In this case study the demand was to produce 500 tons of heavy mineral concentrate from more than 5 000 tons run-of-mine on are mote location with limited to no infrastructure. The various challenges faced and lessons learned are documented as an outcome of the success of this mission.

Jan 1, 2007

By Kedikilwe Oageng

Effective perimeter control during drilling and blasting is critical not only to blasting results but also to the overall stability of the pit over its entire life span. A pit where perimeter control is not given enough attention when conducting drilling and blasting operations, often experiences over-break or back break beyond final pit wall limits, and therefore has a relatively high probability of failure. Such a pit also becomes unsafe, sometimes not easily accessible, has increased loading costs due to production of oversize, longer cycle times and often problems are encountered when blasting subsequent benches. All these are undesirable consequences, which have negative cost implications. Specialised blasting techniques such as trim blasting and pre-splitting have over the years proved to be effective perimeter control measures. However, the success of these techniques is directly attributable to the time and effort given to the processes. This paper presents results of a project undertaken to monitor, review and optimize the trim blasting and pre-splitting processes at Orapa Diamond Mine in Botswana. The project was specifically incepted to improve the final wall conditions, which continued to deteriorate due to persistent over-break during blasting. The paper also analyses the results obtained against a benchmark of results taken prior to project implementation. Specific blast design parameters which are critical to blasting results were identified as problem areas after auditing of the pre-implementation drilling and blasting practices. These include drill-hole depth, spacing, splitting factor for pre-splits and timing of trim blasts. The impact of different rock types on the results was also studied, and recommendations were made at different phases of the project and results obtained after implementation analysed until optimum results were achieved.

Jan 1, 2008

By C. J. Liebenberg

This paper focuses on the application of ion exchange technology for the recovery of copper from a leach solution originating from a heap bioleach in which base metals are leached from a low-grade ore that bears platinum group metals. Screening tests indicated that Dow XUS43605 has high selectivity for copper over the other metals in the solution, namely nickel, iron, cobalt, zinc, manganese, and aluminium. Batch adsorption kinetic experiments showed that copper adsorption equilibrium is attained at a fast rate. The kinetics of adsorption increased as the temperature was increased from 25°C to 60°C due to the decrease in solution viscosity and the subsequent improved intra-particle mass diffusion. Single-component Langmuir and Freundlich isotherm models were fitted to the batch copper adsorption equilibrium data, and a maximum copper capacity of 26 g/l was observed for Dow XUS43605. The effects of flow rate, temperature, pH, and initial metal concentration on the dynamic recovery of copper were investigated in fixed-bed columns, and it was determined that temperature and flow rate had the most significant impacts on the loading of copper on the resin at copper breakthrough. A 36% increase in copper loading at breakthrough was observed when the temperature was increased from 25°C to 60°C. Finally, it was determined that a split elution is possible by using different concentrations of H2S04 to first elute co-loaded nickel from the resin, followed by the elution of copper.

Jan 1, 2013

By F. K. Mulenga, M. Lusambo

"Geometallurgical models are a strategic tool used primarily in planning, diagnosis, and process optimisation. This paper discusses the development of a predictive model for flotation recovery at Kansanshi concentrator in Zambia as a function of key operational parameters. Daily data for milling and flotation from the circuit processing the copper sulphide ore was analysed. This data, recorded over a period of one year of production, was collected from diverse sensors measuring semi-autogenous milling and flotation parameters. Statistical analysis showed that copper head grade, acid-insoluble, and acid-soluble copper, SAG mill throughput, ball mill load, and tonnage of feed material to the SAG mill in the -125 +63 mm size fraction contributed to the prediction power of the proposed empirical model by as much as 90%. Finally, a proposal was made for the development of a simulation model under MODSIM®, a flexible tool for mineral processing applications. This was to test the limitations of the empirical model for future refinement. IntroductionKansanshi is the largest copper mine in Africa and the world’s eighth largest copper producer, with a total of 253 272 t of copper produced in 2016 (Newall, 2017). It is located approximately 10 km north of Solwezi, the capital and administrative headquarters of the North Western Province, Republic of Zambia. The ore deposit consists predominantly of chalcopyrite and malachite with variable amounts of chalcocite, bornite, chrysocolla, and azurite. Because of the varying proportions of sulphide and oxide copper minerals, the ore is classified into three distinct categories: sulphide, mixed, and oxide ores. As such, three separate processing circuits are used to mill the ore down to a standard targeted grind size of 80% passing 150 µm before froth flotation and leaching.A lot of research and development has been done to improve the performance of the sulphide ore circuit at Kansanshi. Despite the research efforts and subsequent operation, the sulphide ore circuit did not attain the target recovery and grade for 2016, primarily because of the complexity of the orebody.The constant drive to achieve the set production target of recovery and concentration grade after froth flotation motivated the development of a tool for the prediction of recovery. The anticipated benefit is not only to enable the plant to apply corrective actions when needed, but also to make a tool available for the quick assessment of the plant performance of the. For that purpose, data spanning June 2016 to May 2017 was analysed, cleaned up and curvefitted to an empirical model. In doing so, key parameters were determined and calibrated to represent the behaviour of the plant."

Nov 1, 2018

By J. McPherson

In order to add value to South Africa?s gold reserves AuTEK, a joint venture between Mintek and Anglogold-Ashanti, was started in 2000 with the aim of developing new industrial uses for gold. Accordingly gold catalysts are being made in kilogram quantities by Project AuTEK and sold toend users and other interested parties under the trade name AUROliteTM. Although these materials are optimized for use in CO oxidation applications, demonstration of appropriate activity, selectivity and durability in both liquid- and other gas-phase reactions has been shown1. The review below highlights the recent use of these materials, and other gold catalysts, in reactions of commercial interest.

Jan 1, 2009

The term geostatistics was introduced by Matheron (1960) to cover the development and application of mathematical and statistical models which take specific account of the spatial structure of a 'regionalised' variable. In ore valuation the relative positions of available ore values within an ore body or portion thereof, can only be ignored in the unlikely case where there is no significant pattern of association or correlation between them - that is, if they do not disclose any significant spatial structure. A structure might not be evident in the available data, e.g. where the spacing of the available values is relatively wide such as in surface drilling on a new deep gold mine. However, practical selective mining considerations could dictate the need for eventual underground valuation on a scale much smaller than that represented by this spacing and the possibility of a significant structure on such a smaller scale cannot then be ignored. Some spatial structure must be present wherever the average variability among the values of check ore samples from the same, adjacent or nearby grooves or of borehole cores from the deflections in the same borehole, is lower than the overall variability for ore values within the whole ore body. Another practical check on the presence of a spatial structure is where it is evident that there is or will be a significant variation in the ore grades for individual ore blocks. Any correlation between peripheral and follow-up internal ore block values also provides evidence of a spatial structure, and hence the regression techniques covered in §1.16-1.2 1 can be accepted as the first application of the geostatistical procedures. The spatial structure of a regionalised variable can be studied and measured by the pattern, usually a decreasing function, in the level of correlation or of the covariance between pairs of values as the distance or lag between the values increases, that is, by the correlogram or covariogram (Krige, 1968, 1969, 1976; and Fig. 18). In geostatistics, for various practical and theoretical reasons (Matheron, 1960, 1971), the measure most commonly used is the semivario- gram, which increases as the lag increases. The semivariogram and covariance values are interrelated and for the lognormal- de Wijsian pattern used extensively for gold ore valuation both measures as well as their relationship can be defined on a fairly straightforward basis. Provided the underlying as- sumptions are realistic, the choice of measure - correlogram, covariogram or semivariogram - will be dictated mainly by convenience. Paragraph 2.2 will cover some general geostatistical terms and $2.3-2.12 will deal mainly with the theoretical side of the lognormal-de Wijsian model for spatial structures. Wherever the relevant variable lends itself to normalisation via the 3-parameter lognormal distribution (see 51.9) the de Wijsian semivariogram model is also likely to be suitable and will provide substantial advantages in application. Various practical applications will be covered in Section 3. Although confined to the lognormal-de Wijsian model, much of the theory covered and the general approach is applicable to all spatial structures. [ ]

Jan 1, 1981

By A. Koursaris, J. B. See

The influence of Iscor coke and Delmas coal on the reduction of Mamatwan manganese ore to ferromanganese was examined by use of a variation of the 'stationary charge in controlled environment' (SCICE) technique. The charges of Mamatwan ore and the appropriate reducing agent were heated to temperatures between 1300 and I600 °C and either allowed to cool immediately the required temperature had been reached or held at that particular temperature for periods of up to ... hours. The heating rate was 350°C per hour, the particle size of the ore was between 2,83 and 12,7 mm, and the particle size of the reducing agent was between 2,83 and 6,35 mm. After being allowed to cool in air, the reacted charges were examined by optical microscopy, X-ray-diffraction analysis, scanning electron microscopy, and electron-microprobe analysis. No significant difference was found between the changes observed during the reduction of Mamatwan manganese ore by Iscor coke and by Delmas coal. A hypothesis is advanced to explain the mechanism of formation of the Fe-Mn-C alloy.

Jan 1, 1979

By W. Wittke, D. Schröder, H. Polczyk

ABSTRACT: The Urft dam, the Diemel dam and the Eder dam are three old masonry damslocated in Germany. The paper describes the rehabilitation measures and the correspondingstability analyses carried out to adjust the dams to today's standards. Remedial works such as theexcavation of inspection galleries, the installation of a grout curtain with a downstream drainagescreen as well as the installation of pre-stressed permanent tendons were carried out. In all threecases the stability of the upgraded dam could be proven on the basis of finite element analyses. ZUSAMMENFASSUNG: Die Urft-, Diemel- und Edertalsperre sind drei alte deutscheSchwergewichtsmauern aus Bruchsteinmauerwerk. Im Beitrag werden Instandsetzungsmaß-nahmen und Standsicherheitsnachweise beschrieben, die erforderlich waren, um die Staumauernan den heutigen Stand der Technik anzupassen. Hierzu wurden Kontrollgänge aufgefahren,Dichtungsschleier mit luftseitiger Dränage sowie vorgespannte Daueranker hergestellt. In allendrei Fällen konnte unter Berücksichtigung der Instandsetzungsmaßnahmen die Standsicherheit derMauer auf der Grundlage von Berechnungen nach der Methode der finiten Elemente nachgewiesenwerden. RÉSUMÉ: Les barrages de Urft, Diemel et Eder sont trois barrages-poids vieux allemandsconstruit de maçonnerie de moellon. Dans cet article, opérations de remise en état et preuves destabilité sont décrits, qui étaient nécessaires pour adapter les barrages à l'état de la techniqueactuelle. À cet effet, des galeries de contrôle étaient creusés, voiles d'étanchéité avec des drains àla face aval et tirants précontraints permanents étaient fabriqués. Dans tous les trois cas, tenantcompte des opérations de remise en état, la stabilité de la barrage pouvait être prouvée à partir decalculs selon la méthode des éléments finis.

Jan 1, 2003

By F. T. Cawood

The new mineral royalty regime for South Africa was signed into law in November 2008, with its main objective being to compensate the State for the depletion of public minerals through a royalty charge payable from 1 March 2010. The aims of this paper are to establish the potential impact of mining royalties on State revenues, industry affordability, and explore whether the dual formula system is likely to encourage miners to become refiners. It also measures the royalty dispensation against economists? tax standards in an attempt to make a judgement on the ?equity? of the new system. This paper argues that most stakeholders should be comfortable with most of the requirements of the Act for most of the time. However, the new regime is unlikely to motivate miners to become refiners, as the benefit of the reduced rate on refined minerals appears to be insufficient to justify the additional costs to refine the mineral resource to the prescribed states of beneficiation.

Jan 1, 2011

By J. Kempken, T. Schreiter, R. Degel, H. Schmieden

After a short summary of the historical milestones of the submerged arc furnace, the paper will highlight different applications and their specific smelting furnace requirements in the non-ferrous area. Additionally, aspects of rectangular furnace design and the features of the copper cooling system for the side wall will be emphasized. Finally a state-of-the-art design tool as well as a new invention to improve slag cleaning technology will be featured, which shows great potentials especially for the PGM and copper related industry. Keywords: submerged arc furnaces, aerro alloys, non-ferrous, copper, slag cleaning, PGM, rectangular furnace, DC technology

Jan 1, 2006

By Keith Rowley, Neal Harries, David Noon

The management of risks associated with slope instability is an essential process in the safe and economic operation of open cut mines. The ?slope stability radar? (SSR) has been developed to better manage those risks. The SSR remotely scans rock slopes to continuously measure any surface movement and can be used to detect and alert users of wall movements with sub-millimetre precision. The high level of movement precision and broad area coverage of the rock face can allow for a better understanding of the geomechanics of slope deformation, including magnitude of potential failures and additional warning time of impending instability. Additionally, radar waves adequately penetrate through rain, dust and smoke to give reliable measurements, 24 hours a day. SSR systems have been deployed in many mines in Australia, Indonesia, South Africa, Zambia, Chile and the United States. Greater than 70 rock falls and waste dump failures (from several to millions of tonnes) have been monitored, and on every occasion precursor ?warning? movements were recorded by the SSR. This technology enables a radical change in the management of risks in open cut mining. This paper will present recent case studies of the SSR operation in coal and metalliferous mines.

Jan 1, 2006