Search Documents

Visit to the Modderfontein factory of A. E. & C. I. Ltd 23rd November, 1972 A full programme was arranged to suit both the mining and metallurgical sections of the Institute. After refreshments were taken and visitors welcomed by the factory management we were split into two groups, viz metallurgical and mining. Book review Stress-relief Heat Treatment of Vanadium Steels by Or G. O. Joy and Or A. M. Sage (21 pp, 77 references).

When a mine decides to construct surface structures close to, or on undermined ground, it is required in terms of the regulations of the Mine Health and Safety Act to obtain permission from the Department of Minerals and Energy (DME). Apart from the legal requirements, the stability of the structures is crucial as damage to the structures due to surface movements could result in loss in life, equipment and/or production. This paper deals with the rock engineering aspects of a study that was conducted on one of the chrome mines in the Bushveld Complex (BC) involving the construction of plant structures on shallow undermined ground. The paper addresses the legal requirements and guidelines regarding ground stability of surface structures placed on undermined ground and the assessment of the undermined area with regard to the following: ?sources of potentially damaging surface movements ?safe mining spans ?stability of the pillars ?effect of the loading of plant structures on underground stability. Due to the irregular layout and geometry of the pillars in conjunction with a changing surface topography, numerical analysis and not the conventional tributary area theory was used to determine the imposed loads on the pillars. In order to subject the plant structures to minimum movement, the plant should be located in areas where the pillars would remain stable, the elastic deformation of the hanging wall is minimized and hanging wall failure extending to surface is unlikely to occur. The study indicates that although the depth of undermining is shallow (between 27 m and 60 m), potential damaging surface movements are not anticipated due to the stability of the pillars, competent nature of the overlying strata and negligible effect of the plant structure loading on the underground stability.

Jan 1, 2004

By J. A. Voster

Premier Mine (a part of De Beers Consolidated Mines Ltd) which is situated 38 km to the east of Pretoria, has the largest known diamond pipe in South Africa. The mine started operations in1903. The Premier Mine kimberlite pipe is unique in that it is intersected by a 75 m thick gabbro sill at a depth of 400 m below surface. The current mining method used is mechanized panel retreat caving, which has been successfully used to extract ore from the different mining blocks. All caving at Premier Mine is below the sill and failure to exercise good draw control could cause the early ingress of gabbro waste. Draw control at Premier Mine is crucial as it aids in preventing conditions of isolated draw, which results in the early ingress of waste, compaction of the kimberlite and the loss of ore reserves. To assist, an underground vehicle monitoring and control (VMAC) system was installed to enable the effective management of the draw control function. The system has evolved graduallyin collaboration with a local developer. The data accumulated is used to decide the most effectivedraw point loading pattern in order to achieve sound draw control principles. This is achieved as each load can be related back to the draw point of origin. The VMAC data recorded also relates back to specific load-haul-dumps (LHDs), tunnels, ore passes, as well as indications of dates, times and payloads recorded. An interface exists between the VMAC and a draw control linear program. Premier Mine’s VMAC system is not a ‘dispatch’ system but rather a draw control system that caters for Premier Mine’s specific block cave requirements. Premier Mine has realized that successful automation is not dependent on technology alone but rather on the successful implementation thereof.

Sep 1, 2001

By M. Bester, R. Carey, T. Russell, J. van Heerden

"In order to reach the goal of optimal and safe extraction of the mineral reserve, the mining industry is increasingly focusing on reconciliation across the mining value chain to ensure that the mining process occurs in a progressively more predictable manner. This will consequently improve the understanding of mine plans and their associated implementation risks, ultimately leading to increased investor confidence. In terms of geotechnical engineering, mine to design performance assessment is a critical aspect of mine to plan adherence focusing on the complex aspects influencing slope performance. A mine to design reconciliation process therefore needs to systematically track implementation and geotechnical aspects in order to review or update slope design criteria and pit layouts according to the mine planning cycle as the mine is developed. This paper describes the development and implementation of a standardized mine to design reconciliation system for operations utilizing laser scanning technology, analysis tools, as well as associated key performance indicators. Performance is evaluated on final pit boundaries in terms of geometry achieved as well as blast performance evaluation of face conditions. These aspects as well as the resulting catch berm capacity should be captured in an information system, enabling longer term trend analysis and detailed root cause analysis where unsatisfactory outcomes occur. Adverse outcomes should subsequently be incorporated into the mine’s risk management process informing risk mitigation measures including blast design adjustments, slope design changes, or rockfall protection measures. IntroductionIn order to reach the goal of optimal and safe extraction of the mineral reserve, the mining industry is increasingly focusing on reconciliation across the mining value chain to ensure that the mining process occurs in a progressively more predictable manner. This will consequently improve the understanding of mine plans and their associated implementation risks, ultimately leading to increased investor confidence. In terms of geotechnical engineering, mine to design performance assessment is a critical aspect of mine to plan adherence focusing on the complex aspects influencing slope performance. A mine to design reconciliation process therefore needs to systematically track implementation and geotechnical aspects in order to review or update slope design criteria and pit layouts according to the mine planning cycle as the mine is developed."

Jan 1, 2016

By P. J. D. Lloyd

The Witwatersrand reefs contain gold, uranium, and pyrite in the following average concentrations: 0,001 per cent, 0,02 per cent, and 1,7 per cent respectively. The paper discusses the flotation of pyrite to produce a s,ulphide concentrate, reviews work done on the production of gold concentrates, discusses attempts to produce maximum concentrates, and closes with a review of processes for the simultaneous flotation of these three species. It is concluded that high recoveries of all three species can be achieved only if a rougher concentrate of perhaps 20 per cent of the feed (by mass) IS produced, and it is suggested that reverse leaching (leaching before cyanidation) of this concentrate, followed by a cleaning flotation step for the recovery of the pyrite, would be more efficient than the routes employed at present.

Jan 1, 1981

By T. R. Marshall

SAMREC (The South African Code for the Reporting of Exploration Results, Mineral Resources and Mineral Reserves) Clause 7 notes that ‘Documentation detailing Exploration Results, Mineral Resources and Mineral Reserves from which a Public Report is prepared must be prepared by, or under the direction of, and signed by a Competent Person.’ Similar statements with respect to Competent Valuators (CVs) and Qualified Reserves Evaluators (QREs) are contained in the SAMVAL (South African Code for the Reporting of Mineral Asset Valuations) and SAMOG (South African Code for the Reporting of Oil & Gas Resources) codes respectively. What does it mean to be a Competent Person (CP) in the context of compiling/signing-off on SAMCODE (South African Mineral Code) compliant documents? What do the registration and experience requirements mean? Who is ultimately responsible for the report and what does such responsibility prescribe?

Sep 1, 2021

By I. M. Wolf, S. A. Usmar, L. A. Cornish

The limiting criterion in the use of stainless steel for certain forming operations such as coining is its hardness, which determines parameters such as required striking pressure, wear on dies, and integrity of pattern detail. Attention is given here to the development of ultra-soft ferritic stainless steels for coinage. In the first instance, the influence of carbon content on the striking properties of a series of commercial and experimental 17%Cr alloys was evaluated. It was found that a lower carbon content permitted the striking of relatively highly profiled and intricate patterns, provided that the hardness did not exceed 125 HV. Hardnesses as low as 115 HV were achieved in the fully annealed condition, but these alloys required high striking pressures. In a further study, three grades of experimental 14%Cr ferritic stainless steels were produced with a view to optimizing the ductility. When the residual impurities were minimized, hardness values of about 100 HV and lower were achieved. Micro-alloying additions allowed the heat-treatment response and grain size to be controlled. Excellent tensile properties, with elongations of up to 42 per cent, were achieved in the fuly annealed condition, and highly profiled patterns were produced in coining trials.

Jan 1, 1993

By M. Klapwijk

Ancient Metallurgy - In addition to the preceding three papers, the following three contributions were received for publication 1. An analysis of Bantu-made iron implements from the Letaba district M. KLAPWIJK INTRODUCTION It has often been stated that it is hardly possible in South Africa to classify Bantumade iron hoes according to their places of origin and manufacture. It is well known that these hoes were used for barter, and as currency in the purchase of livestock or the payment of lobolo, although reports of the value of the hoes differ widely. The difficulty in their classification has arisen from their distribution over a very wide area.

Jan 1, 1974

By A. Smith

After the introduction of mechanized bord-and-pillar development at Dumacol in 1958, pillars were being developed at a much faster rate than they could be extracted by hand loading methods. Efforts were therefore made to increase the rate of pillar extraction by mechanization. Following two partially successful mechanized stooping trials in 1964 and 1971, it was decided that mechanized pillar extraction with 1 m3 cable-reel front-end loaders should be introduced. The first section to employ the new equipment started production in May 1979, and the mine now has four mechanized pillarextraction sections in operation. Considerable improvements in production, productivity, safety, and percentage extraction have been achieved.

Jan 1, 1985

Metso Minerals Cisa have developed VisiofrothTM - a system which calculates parameters of the froth surface using vision from remote cameras mounted about individual flotation cells. The parameters calculated from this system can be utilised within process control strategies to achieve stabilisation or optimisation of the flotation process. As part of a JKMRC AMIRA P9 field campaign, froth vision was collected from various cells operated at different air rates and froth depths within Rio Tinto's Northparkes copper roughing and scavenging circuit. At the same time, samples were collected to determine the cell metallurgical performance at each operating condition. These froth images have been processed using the VisiofrothTM system with froth velocity, bubble size, froth collapse rate and various froth colour parameters calculated. These parameters have been compared to the measured concentrate flow and concentrate grade produced at each condition. This analysis shows that the concentrate tonnage flow is strongly correlated with froth velocity whereas the concentrate grade is best correlated using froth velocity in combination with a bubble stability parameter which affects the bubble size distribution on the top surface of the froth. This paper summarises the results from this analysis as well as an overview of the VisiofrothTM system and the parameters that are measured by the software.

Jan 1, 2007

By I. M. W. Preston

A new shaft system was required to replace stope face for the North Section of Harmony Mine and to allow for systematic opening up of the North Eastern Section. Owing to the economic circumstances at the time the project started, it became vital to alter the original planning and to sink the service shaft first. The MATLA coal-sinking headgear, a novel presinking arrangement, allowed sinking to continue to 108 m concurrently with the erection of the permanent sinking headgear and sinking winders. It is estimated that this arrangement resulted in a saving of two months on the overall project.

Jan 1, 1983

By R. W. O. Kersten

This paper describes the method used at Agnes Gold Mine in the calculation of pillar strengths, which involves a back-analysis type of approach. The results obtained there are comparable with those obtained by accepted formulae for pillar strength. It was found that a stress level of 70 MPa for the width of combined pillars (Le. crown and sill pillars) causes failure of the reef drives as well as the tops and bottoms of the stope side walls. As shrinkage stoping to depths of more than 650 m would result in very low percentage extractions, alternative methods of stoping will have to be investigated for these depths.

Jan 1, 1984

By A. Melkumyan, M. Balamurali, J. Zigman

Understanding the contribution of geophysical variables is vital for identifying ore indicator regions. Both magnetometry and gamma-rays are used to identify the geophysical signatures of the rocks. Density is another key variable for tonnage estimation in mining, and needs to be re-estimated in areas of change when a boundary update has been conducted. Modelling these geophysical variables in 3D will enable investigation of the properties of the rocks and improve our understanding of the ore. The Gaussian Process (GP) was previously used to generate 3D spatial models for grade estimation using geochemical assays. This study investigates the influence of the following two factors on the GP-based autonomously generated 3D geophysical models: the resolution of the input data, and the number of nearest samples used in the training process. A case study conducted on a typical Hammersley Ranges iron ore deposit using geophysical logs, including density, collected from the exploration holes, is examined in this paper.

Sep 1, 2021

Now a new generation of computerized drill rigs has been launched and they are based on modern standard PC-computer technology. The rigs have been well embraced by the market and more than 100 units have left the assembly line. The new generation has taken a quantum leap forward with respect to drilling accuracy, logging capabilities, reduction of manpower in some types and serviceability compared to the previous generation of drill rigs. The Can bus technology, well proven in the automobile products, is the backbone in the new generation control system of Atlas Copco. The short-term development is now focused on establishing this new automation platform on other product lines of Atlas Copco products. The long-term objectives is to offer the mining industry Atlas Copco products with one common automation platform. Essential for Atlas Copcois to contribute to the work with the on-going Data Exchange standard between mining machines and mining computer systems (IREDES). Our belief is that an accepted standard will make mine automation programs affordable for a wider base of the mining industry, because of the possibilities to a cost effective integration of different equipment with a minimum of system integration problems and machine specific interfaces.

Sep 1, 2001

By J. Manchisi

Laboratory investigations were conducted to establish the feasibility of bioleaching a mixed copper oxide/sulphide rougher concentrate from Nchanga Mine on the Zambian Copperbelt. The objective was to determine the kinetics and extent of copper extraction for this material. Batch experiments were conducted under different solution conditions in stirred tank bioreactors. The progress of (bio)leaching was monitored through measurements of soluble ferrous and ferric iron, copper, pH, and redox potentials, while bacterial activity was monitored online through 02 and C02 gas utilization rates. About 20 per cent copper was solubilized within 2 hours in all cases of non-oxidative (abiotic), oxidative (abiotic), and bioleaching experiments. This was attributed to the dissolution of mainly copper oxides. Subsequently, bioleaching experiments resulted in an overall copper extraction of 93 per cent, with up to 8 g.L-1 copper after six leaching days, compared to 58 per cent copper extraction in the abiotic oxidative acid leaching experiments. However, there was little effect of time (i.e. poor dissolution kinetics) on copper recovery for abiotic non-oxidative acid leaching of the material. Hence, the rate of sulphide leaching increased due to the activity of bacteria. Thus, the material is potentially bioleachable under mesophilic conditions. However, more exhaustive test work needs to be conducted to establish the effect of bioleaching variables and heat requirement.

Jan 1, 2012

By B. X. Huang

Hydraulic fracturing technology is presented as a solution to improve permeability and thus solve the extraction problem of coal seam gas in low-permeability gas-bearing coal seams. Given an existing group of original cracks, the propagation of main hydraulic cracks and hydraulic wing cracks was simulated using realistic failure process analysis software. The process represents the structural transformation of hydraulic fracturing and permeability improvements caused by it. In addition, a field test for improving the permeability of gassy coal seams by hydraulic fracturing was also conducted. The propagation of the main cracks and wing cracks by hydraulic fracturing forms a network of original joint cracks, hydraulic wing cracks, and main hydraulic cracks, which improve the permeability of the coal seam. High-pressure water in the drill hole and in the main hydraulic cracks permeates the two flanks of the hole, forming the permeating water pressure. With an increase in drill water pressure and an extension of the main hydraulic cracks, the permeating water pressure on both sides of the main hydraulic cracks in the coal mass also increases. Hydraulic cracks tend to form connections through rock bridges. The extension of hydraulic wing cracks through connections in the rock bridges between the cracks transforms the rock mass to a fractured structure and improves its permeability. Hydraulic fracturing technology for improving permeability in underground conditions can increase the amount of gas drainage by a factor of 15. A stress relief area develops at a radial distance of 10-2.0 m from the hydraulic fracturing drill hole, while an area of rising stresses, called the pressurized area, develops a further 15 m away from the pressurized hole. Practice has proved the existence of the stress transfer phenomenon and the high stress area after fracturing. This kind of hydraulic fracturing technology is more effective in holes drilled from underground than in surface drill holes, with respect to costs and controllability, and is therefore the major trend in gas drainage development in coal mines.

Jan 1, 2012

By H. E. Parkinson, Y. P. Chugh

About 90 percent of the coal mined underground in the U.S.A. today is mined by the room-and-pillar system. The productivity of the system dropped from about 14,1t per man-day in 1969 to about 7,3 t per man-day in 1978. Since 1974, the U.S. Department of Energy (formerly the U.S. Bureau of Mines) has been engaged in research to improve the production and productivity of the room-and-pillar system. The effort involves the development of integrated, automated, and remote-controlled equipment and systems including remote-controlled continuous miners, automated miner-bolters, automated extraction systems, continuous haulage systems for use behind miners, and remote-controlled equipment for miners, bolters, and shuttle cars. These systems are discussed briefly, the discussion being related primarily to coal winning, although the concepts could be utilized in room-and-pillar systems in mines other than coal mines.

Jan 1, 1981

By B. X. Huang

Hydraulic fracturing technology is presented as a solution to improve permeability and thus solve the extraction problem of coal seam gas in low-permeability gas-bearing coal seams. Given an existing group of original cracks, the propagation of main hydraulic cracks and hydraulic wing cracks was simulated using realistic failure process analysis software. The process represents the structural transformation of hydraulic fracturing and permeability improvements caused by it. In addition, a field test for improving the permeability of gassy coal seams by hydraulic fracturing was also conducted. The propagation of the main cracks and wing cracks by hydraulic fracturing forms a network of original joint cracks, hydraulic wing cracks, and main hydraulic cracks, which improve the permeability of the coal seam. High-pressure water in the drill hole and in the main hydraulic cracks permeates the two flanks of the hole, forming the permeating water pressure. With an increase in drill water pressure and an extension of the main hydraulic cracks, the permeating water pressure on both sides of the main hydraulic cracks in the coal mass also increases. Hydraulic cracks tend to form connections through rock bridges. The extension of hydraulic wing cracks through connections in the rock bridges between the cracks transforms the rock mass to a fractured structure and improves its permeability. Hydraulic fracturing technology for improving permeability in underground conditions can increase the amount of gas drainage by a factor of 15. A stress relief area develops at a radial distance of 10-2.0 m from the hydraulic fracturing drill hole, while an area of rising stresses, called the pressurized area, develops a further 15 m away from the pressurized hole. Practice has proved the existence of the stress transfer phenomenon and the high stress area after fracturing. This kind of hydraulic fracturing technology is more effective in holes drilled from underground than in surface drill holes, with respect to costs and controllability, and is therefore the major trend in gas drainage development in coal mines.

Jan 1, 2012

By D. D. Marsden

The paper briefly outlines the history of the successful development of vegetating techniques for mine-residue deposits. It seeks to place on record the major roles played by M.J. Mrost, who initiated and systematically developed the concept, and W.H. Cook, who continued the trials and successfully directed a stupendous large-scale project. The vegetating techniques currently practised are outlined, and it is concluded that vegetating is still the only surface-stabilizing technique of any significance that is employed throughout the world.

Jan 1, 1987

By Z. Halifa, P. G. Geyer

Tapping a blast furnace is necessary not only to deliver the product, but is also essential for the safety of the furnace and workers in the cast-house. This paper will highlight the practices at ArcelorMittal’s blast furnaces in the Vanderbijlpark Works, with specific focus on tap-hole design and monitoring as well as casting practice. Extension of the tap-hole life and hearth campaign will be illustrated with reference to the methods of maintenance of the tap-holes, troughs, runners, and cast-house equipment. The importance of proper cooling, good thermocouple installation, and temperature monitoring will be explained.

Jan 1, 2014