Search Documents

By H. L. Riley

Cleaning and handling of fine coal are generally conceded to be more difficult problems than preparation of the coarser sizes. Increased mechanization in the coal-mining industry has, in general, resulted in an increased percentage of the fine sizes in the total coal mined. If the coal fines are cleaned by wet methods, the minus-1/16-inch square-mesh particles cause most of the sludge and slurry problems encountered in preparing wet coal. Equipment that separates coal from refuse on the basis of specific gravity is not efficient on sizes that, because of their fineness, do not follow the same laws of hindered settling as the larger particles. Probably the best solution of fine-coal cleaning problems is to use other methods, such as flotation, that utilize other physical characteristics than those determining hindered-settling ratios. Regarding the type of flotation known as the Elmore vacuum-flotation process there has been a scarcity of data and information available in this country. An investigation has therefore been made to obtain additional date and information on this process under laboratory conditions. During this investigation an effort has been made to evaluate the relative efficiencies of vacuum and mechanical laboratory froth flotation cells. The investigation included float-and-sink, screen-sizing, and flotation tests on 2 different samples of 14-mesh to 0 raw coal and an a sample of slurry from the settling-tank overflow of a typical washer. One raw-coal sample was obtained from the American bed and represented a type of coal that is relatively easy to clean. The other raw-coal sample was from the Mary lee bed and represented a type considered difficult to clean.

Jan 1, 1954

By D. Randolph Berry

Volume II contains appendices which explain and document the recommendations of Volume I. The following topics are covered: Appendix A Discussion of Recommended Guidelines Appendix B Worldwide Use of Oxygen Self-Rescuers Appendix C Hypothetical Use of Oxygen Self-Rescuers in Post-1972 Coal Mine Explosions and Fires Appendix D Vibration Testing of SCSRs Appendix E Testing of In-Service Chemical Oxygen SCSRs Appendix F Discussions with Representatives of Underground Coal Mining Appendix G Recommendations for SCSR Storage Containers Appendix H Example SCSR Storage Plans Appendix I Testing of In-Service Compressed Oxygen SCSRs Appendix J 30 CFR 75.1714, 30 Regulations Pertaining to Self-Rescuers

Jan 1, 1981

By Eugene T. Sheridan

The Bureau of Mines annually canvasses the fuel-briquet and packaged-fuel producers in the United States and publishes economic data on these industries, based upon reports submitted voluntarily by producers. This publication lists all producers that reported commercial production to the Bureau for 1960 and presents data on individual plants. The companies named herein represent virtually all producers of processed minerals fuels. A few small plants may not have been canvassed or failed to respond to the survey because some of the smaller plants operate intermittently and the survey is voluntary. All plants that reported commercial production were included; regardless of size. Specifically excluded were plants that manufactured briquets from wood charcoal. Fuel briquets and packaged fuel are manufactured solid fuels, produced by mixing fine-sized mineral fuels with binding materials and compressing into small individual shapes, Briquets are produced in pillow-shaped and cylindrical form, are 2 to 4 inches long, and weigh 2 to 4 ounces. Packaged fuel consists of 3- or 4-inch cubes; 6 or 8 of which are wrapped together in heavy kraft paper to form a package weighing 10 to 15 pounds, Briquets are durable and may be stored and handled as bulk fuel; packaged fuel breaks easily and must be stored indoors to prevent it from deteriorating. Whereas briquets are consumed in many areas as a general residential fuel, packaged fuel is more of a specialty item, used at times to supplement other fuels. Packaged fuel is burned without re-moving the paper and is referred to as the "white glove" fuel.

Jan 1, 1961

By Bing W. Jong

A bench-scale evaluation of coal and coal waste materials as aggregate materials for use in longwall mine supports was undertaken as part of the Bureau of Mines Health and Safety program on ground control. Performance data were obtained on portland cement concretes (PCC) prepared with coal and coal wastes as aggregate materials. The effects of high-early-strength accelerators on strength and creep and of superplasticizers on strength properties of PCC formulated with coal and coal waste were investigated. Concrete formulated with a high-early-strength accelerator and coal and coal waste has 20 and 40 pet greater compressive strength, respectively, than the control samples without admixture. A concrete formulated with coal waste and the high-early-strength accelerator, using four bags of cement per cubic yard and a water-cement ratio of 1.0, had the lowest creep value of all the coal- and coal-waste-formulated PCC's tested.

Jan 1, 1983

By Gary E. Sherman

Preliminary economic mining feasibility studies were conducted by the Bureau of Mines to estimate mining costs in the Juneau gold belt area of the Juneau Mining District, southeastern Alaska. Investigations were conducted on the economics of two mineral deposit types: (1.) Berners Bay vein gold deposits, and (2.) stockwork gold deposits containing gold, silver, and lead. Cost estimates were developed using the Bureau of Mines Cost Estimating System (CES). Discounted cash flow return on investment (DeFROI) was calculated using the Bureau's MINSIM computer program. Underground mining of a Berners Bay vein gold deposit was found to be economic (15 pct DCFROI) at a recoverable metal value of $353.67/mt for a 100 mtpd shrinkage stoping mine with a 10 yr mine life, $324.76/mt for a 20 yr mine life, $138.63/mt for a 500 mtpd longhole stoping mine with a 10 yr mine 1 ffe, and $127.50/mt for a 20 yr mine life. Block caving mining of a large stockwork gold deposit was found to be economic at a recoverable metal value of $15.28/mt for a 18,000 mtpd mine with a 20 yr mine life.

Jan 1, 2011

By W. L. Hunter

The research on this report was conducted to obtain information on the feasibility of producing ferro chromium of varying silicon and carbon contents from domestic chromite. Concentrates from the Mouat deposit were chosen because they typify the chromite found in the Stillwater complex, the largest domestic reserve, and are similar in composition to other extensive North American and foreign deposits. Batch-smelting tests designed to produce high-, medium-, and low-carbon ferrochromium were made in single phase and three-phase, electric-arc, steelmaking furnaces. Agglomeration studies were made in a rotary kiln. Continuous smelting tests were made to yield data on the production of high-carbon ferro chromium and low-carbon ferrochromium-silicon. The carbon content of high-carbon ferrochromium was lowered to the medium-carbon range by oxygen injection. Mouat stockpile concentrates were nodulized in a gas-fired rotary kiln using quartz, limestone, and fluorspar additions in the proportion necessary to flux the slag. The nodules were smelted in a continuous test using coal, coal char, and mixtures of the two consecutively as reductants.

Jan 1, 1961

By James A. Brierley

Wastewater from uranium mines in the Ambrosia Lake district near. Grants, New Mexico, U.S.A., contains uranium, selenium, radium, and molybdenum. The Kerr-McGee Corporation has a novel treatment process for waters from two mines, sections 35 and 36, to reduce the concentrations of the trace contaminants. Particulates are settled by ponding, and the waters are passed through an ion exchange resin to remove uranium; barium chloride is added to precipitate sulfate and radium from the mine waters. The mine waters are subsequently passed through three consecutive algae ponds prior to discharge. Water, sediment and biological samples were collected over a 4-year period and analyzed to assess the role of biological agents in removal of inorganic trace contaminants from the mine waters.

Jan 1, 1981

Under contract from U. S. Bureau of Mines, Harza Engineering Company in cooperation with Eastern Associated Coal Corporation, conducted a ground control study of two mechanized longwall panels at the Federal Number 2 Mine. The mine is located in Northern West Virginia, and the coal is mined from the Pittsburgh Coal Seam. The prime objective of the study was to collect data which will aid in the proper selection of the longwall supports system and to control the entry caving problem. Instruments installed in the mine were borehole pressure cells, convergence recorders, roof sag recorders, horizontal roof strain indicators, differential floor movement systems, and lateral roof and floor movement systems. Instruments installed on the surface, above the instrumented longwall panels, consisted of slope indicator system, vertical bed settlement probe system and shear displacement detecting system. A comprehensive surface subsidence study was conducted in conjunction with the instrumentation. In addition to the instrumentation and monitoring, special tests were conducted to determine the bearing capacity of the roof and floor rocks, in situ modulus of coal, roof and floor rocks, and response of borehole pressure cells to ground stress. Cores of coal measure rocks were collected for the physical property tests. Face observations were made to detect various roof behavior parameters under the different jack setting pressures. This report essentially describes the instrumentation work, special tests and presents the data collected.

Jan 1, 1976

By Gary E. Sherman

To aid the U.S. Army Corps of Engineers in their Resource Development Navigation Study, the U.S. Bureau of Mines (Bureau) examined the potential for mineral development near ten Alaska port sites. This report presents the results for the following four sites: Balboa Bay, Beluga, Lost River, and Point MacKenzie. There are 579 known deposits within the area considered for these ports. The majority of the deposits are located within a highway/railroad corridor examined for the Point MacKenzie port site. Based on the current level of knowledge, coal deposits near the Beluga and Point MacKenzie port sites are most likely to be developed in the near future. This conclusion is based on the fact that coal projects in these areas are actively being pursued for development. The mineral wealth surrounding the four port sites is substantial. Mine models were used to examine the potential for mining tin, gold, silver, copper, and molybdenum. The models were based on published reserve and grade data and therefore do not include proprietary company data which, if available, would likely change the analysis results. Of the models examined, the tin placer mine model developed for the Lost River port site proved to be closest to being economic.

Jan 1, 2011

By R. Ward Stahl

The underground junction or intersection is analogous to the doorway or window in a building in that the continuous wall or support for the overhead structure has been weakened by making the opening. Some type of bridge or support seems necessary to prevent roof sag and possibly eventual failure at this point, although frequently it appears that little is done until a fatal accident induces action. The intersection generally represents less than 15 percent of the exposed roof area. As a result of recent multiple fatalities, some of which occurred at or near intersections, the Bureau of Mines was asked to examine the junction-support problem more thoroughly and to report its findings. A national survey of the junction-support systems in use has been made by correspondence, and the local area has been canvassed rather thoroughly to determine just what and how much is being done.

Jan 1, 1962

By Pramod C. Thakur

In This Chapter [Origins of coalbed methane Reservoir properties of coal seams Thresholds for coal seam degasification Methane emissions in mines Methane drainage techniques How to transport gas safely in mine pipelines and Economics of coal seam degasification Recommended publications on coal seam degasification are Gas Control in Underground Coal Mining [Creedy et al. 1997], Coalbed Methane Extraction [Davidson et al. 1995], and Methane Control for Underground Coal Mines [Diamond 1994].] ORIGINS OF COALBED METHANE AND RESERVOIR PROPERTIES OF COAL SEAMS Origins of coalbed methane. Coal seams form over millions of years by the biochemical decay and metamorphic transformation of plant materials. This coalification process produces large quantities of byproduct gases, such as methane and carbon dioxide. The amount of these byproducts increases with the rank of coal. It is the highest for anthracite, where for every ton of coal nearly 1,900 lb of water, 2,420 lb (20,000 ft3) of carbon dioxide, and 1,186 lb (27,000 ft3) of methane are produced [Hargraves 1973]. Most of these gases escape to the atmosphere during the coalification process, but a small fraction is retained in the coal. The amount of gas retained in the coal depends on a number of factors, such as the rank of coal, the depth of burial, the type of rock in the immediate roof and floor, local geologic anomalies, and the tectonic pressures and temperatures prevalent at that time. The gases are contained under pressure and mainly adsorbed on the surface of the coal matrix, but a small fraction of gases is also present in the fracture net-work of the coal. Methane is the major component of gases in coal, comprising 80%–90% or more of the total gas volume. The balance is made up of ethane, propane, butane, carbon dioxide, hydrogen, oxygen, and argon.

Jan 6, 2006

By K. J. Liles

Research was undertaken by the Bureau of Mines to determine the technical feasibility of producing lightweight aggregate from the waste glass fraction of municipal incinerator residues. Tests were conducted to determine the amount and optimum size of glass, the amount of sodium silicate, and the method used to form the material to be expanded. The most suitable mixture, 78 percent glass, 20 percent clay, and 2 percent sodium silicate, was pelletized and then expanded by exposure to a temperature of 1,550° F for 15 minutes The resulting lightweight material had a bulk density of 38 lb/cu ft and exhibited excellent pore structure. Concrete test cylinders made from the light weight aggregate had a unit weight of 104 lb/cu ft and a compressive strength of 2,550 lb/sq in after a 28-day steam cure.

Jan 1, 1976

This summary of State laws on explosives wag compiled primarily to ascertain what subjects relating to their control have been acted upon by each State legislature and, in general, how they have been treated. It does not Include any legislation passed after 1942, or any proclamations, regulations, or administrative orders. It does not purport or attempt to be authoritative. If any problem arises involving interpretation of the statutes of any particular State, the original source must be consulted for the exact words used by the legislature. This summary, however, will be useful in determining whether relevant statutes exist, and in locating them quickly, with a minimum of effort. It will be of value also in comparing statutes in other States to determine what construction has been placed upon them by the courts of these jurisdictions or to contrast the varying provisions of many States upon a similar subject. To make these comparisons easier, the statutory provisions for each State have been grouped under several major topics in outline form. Although this sometimes has resulted in disruption of the continuity of individual acts, the increased general clarity and availability of comparable sections have more than justified the procedure followed.

Jan 1, 1943

By M. S. Seehra, V. S. Babu

"INTRODUCTION The accurate determination of the free silica index in coal mine dusts is an important requirement because severe health hazards are believed to be associated with the inhalation of respirable-sized silica particles.1-6 Free silica refers to the three polymorphs of silica (Si02)viz., quartz, cristobalite, and tridymite-although quartz is usually the dominant form in most mine dusts.6 The free silica index is the concentration in micrograms of free silica in air per m3 of air sampled corrected to standard conditions of 25°C and 760 mm/Hg, the present MSHA (Mine Safety and Health Administration) limit on time-averaged basis being 100 µ.g/m 3 for coal mines. A recent review7 has concluded that quartz, cristobalite, and tridymite particles impart nearly equal long-term hemolytic damage when compared on a per unit surface area basis.At present, two experimental methods-viz., transmission infrared spectroscopy (TIRS) and x-ray diffraction (XRD)-are commonly used for the determination of silica concentrations in mine dusts. In TIRS, which has been adopted by MSHA and is commonly called the P7 method, the silica absorption band near 800 cm - 1 is used for quantification. However the mineral kaolinite, which is commonly present in mine dusts, also has absorption band, albeit weaker, at 800 cm- 1• To correct for this interference, one uses the stronger 915-cm -1 band of kaolinite to determine the concentration of kaolinite, and the kaolinite contribution to the absorbance at 800 cm-1 is then determined from a calibration curve, leading to the determination of silica by subtraction. In the XRD technique, usually an internal standard such as CaF 2 is used to determine the concentration of silica from line intensity measurements. XRD has the added advantage that concentrations of quartz, cristobalite, and tridymite can be determined.8•9 In an exhaustive study on the precision of the techniques ofTIRS and XRD for monitoring worker exposure,9 the conclusion has been reached that both methods measure silica within 253 of the ""true"" value 953 of the time in a single laboratory."

Nov 1, 1995

"SUMMARYThe K.M.A. reservoir was discovered to be oil bearing at a depth of 3,719 feet on March 11, 1931. Extensive development, however, was not begun immediately, because the discovery well had a low initial daily oil production, and market conditions for oil were unfavorable. Development of the field progressed slowly for the next 6 1/2 years. In the latter part of 1937, a wildcat well approximately 2 miles southwest of the discovery well was drilled on a magnetometer high and completed with an initial flowing production of 2,016 barrels of 43° A.P.I.-gravity oil in 12 hours. Rapid development of the southwestern part of the K.M.A. field was begun immediately and continued until over 700 wells were drilled and approximately 12,500 acres proved oil productive.Because of the large size of the entire K.M.A. field, this report is limited in scope to the southwestern part only, and the discussion that follows pertains to this area only. The closing date for production statistics is August 1, 1949.The K.M.A. structure is a complex anticline having a maximum closure of 250 feet, and the K.M.A. formation is composed of sediments that grade from limestone through sandy lime and limy sand to sandstone with thin streaks of shale. Two distinct members of the K.M.A. formation, zone I and zone II, are oil productive. Core analyses indicate the average porosity to be 16.5 percent for zone I and 16.1 percent for zone II. A relationship was established from core data, which showed the correlative permeabilities to be 42.1 millidarcys for zone I and 39.5 millidarcys for zone II, whereas the arithmetical averages of the permeabilities were 84 millidarcys for zone I and 216 millidarcys for zone II. Connate water saturations were 17.5 percent for zone I and 20.0 percent for zone II. The porosity-saturation method, using a thickness-correction factor, was employed to calculate the volume c 168.1 million barrels of stock-tank oil initially in place in the reservoir. Analyses of the reservoir oilIn that, although the initial reservoir pressure was 1,750 p.s.i., the original reservoir oil was saturated to only 1,300 at which pressure 1 barrel of stock,tank oil contained 525 cubic feet of gas in solution.A serious decline in reservoir pressure during the 2 years of rapid development alarmed the operators and caused them to consider a cooperative pressure-maintenance program. In the latter part of 1939, the K.M.A. Pressure Maintenance Association was organized, and the gasoline plants in the field agreed to process the wet gas and return the dry gas to leases having gas-injection wells. Approximately 27 percent of the cumulative volume of produced gas had been returned to the reservoir by August 1, 1949."

Jun 1, 1952

By David C. Benson

This Bureau of Mines report is an update of IC 8725 and comprises tables listing the name, location, and other pertinent data concerning certain fuel-related projects. The tables include information on projects involving the proposed or planned development of fuel resources, as well as the development of storage, transportation, and conversion facilities; the report covers the 26 States east of the Mississippi River. Of the total 535 projects for which information is provided, 429 concern coal mines and electric generating plants (including Energy Supply and Environmental Coordination Act (ESECA) coal conversion notices).

Jan 1, 1978

By G. Richards Gwinn

"Mica" is a group name for a number of orthosilicates of aluminum with magnesium, ferrous iron, and the alkalies. They are characterized by their high reflection and a basal cleavage so well developed that they can be split into exceedingly thin laminae, which are more or less tough, elastic, and transparent, according to variety. Barium, manganese, lithium, chromium, titanium, boron, and ferric iron occur in same varieties. Eight distinct species of true mica, which appear in the following table, are recognized by mineralogists, but only the first five are of commercial importance. [Species General Formula Muscovite H2KA13 (SiO4)3 Phlogopite [H,K, (MgF)]) Mg3A1 (Si04)3 Biotite (H,K)2(Mg,Fe)2(Al)Fe)2 (S104)3 Lepidolite K,Li Al(OH,F)2 Al (5103)3 Ros coalite H8K(Mg,Fe) (A1,V)4 (S103)12 Paragonite H2NaAl3(S104)3 Zinnwaldite (K)Li)3 FeAl3 Si5016(OH,F)2 Lepidomelene HK2F3IIIFe6III A13 (S104)9]

Jan 1, 1951

By R. S. Warfield

Several reconnaissance-type surface and drill core samples of Arctic Northwestern Alaska coals were taken during the summer field seasons of 1964 and 1966 for coking studies. Surface samples were taken from the Kokolik River and the Cape Beaufort areas; core samples were obtained from the Kukpowruk River and the Cape Beaufort areas. Only one Kokolik River surface sample possessed coking properties. This sample, representing an 11.6-ft coal seam, made coke approaching metallurgical quality when a 30-pct portion of selected blending coals was added. Four Kukpowruk River core samples, each representing the same 19-to 20-ft coal seam, were all of about the same coking quality. No differences of coke quality attributable to depth of permanently frozen overburden were found, but the data confirm previously reported information that the 19- to 20-ft coal bed is a potentially satisfactory base coking coal. In the Cape Beaufort area, a core sample with appreciable coking properties was taken at depth from a coalbed determined noncoking in a surface sample.

Jan 1, 1969

By A. C. Fieldner

"Gas hazards may be divided into two principal classes- namely (1) inflammation and explosions; (2) asphyxiation and poisoning. Inflammation and explosion are prevented first by adequate ventilation so that gas sufficient to propagate flame or explosion can not accumulate, and second, by avoiding sources of ignition such as open lights, flames, sparks, electrical arcs, short circuits, or sparks. Ventilation is also the best preventive measure against asphyxiation and poisoning from toxic gases. When men must enter unventilated or poorly ventilated places containing poisonous or asphyxiating gases, suitable gas masks, hose masks, or oxygen breathing apparatus should be worn. As a rule, loss of life and property from gas hazards is due to ignorance of the properties and hazards of various gases commonly used, and consequently a failure to use proper measures for eliminating and meeting these dangers. It is the purpose of this paper to describe briefly the common gases and vapors with respect to the hazards involved in their use and to discuss the necessary precautions and methods for avoiding these dangersLight, heat, and power are prime essentials of our modern industrial civilization. The combustible gases and vapors used for the production of these necessary elements of our existence comprise the largest and most common group of domestic and industrial gas hazards. Almost every individual in his daily life subject to possible danger from asphyxiation, fire, or explosion due to one or more of these gases. For evidence one need only refer to the daily newspaper where headlines such as the following are frequently seen; ""Family asphyxiated by carbon monoxide from gas heater;"" ""Schoolhouse wrecked by gas explosion in basement;"" ""Man killed by automobile exhaust fumes in his garage;"" ""Fireman overcome by smoke fumes in basement ""Woman"".""Boman severely burned by accidental ignition of gasoline used in cleaning gloves;"" and 'in recent Years we often see ""Building wrecked by explosion of still in residential district.""It will be noted that these accidents are due to inflammation, explosion, or asphyxiation. Any combustible gas or vapor, when mixed, with air or oxygen within certain limiting proportions, will explode on ignition. The violence of the explosion varies with respective proportions of air and gas, and with the degree of confinement of the mixture. For example: Mixtures of natural gas and air containing between 4.5 and 12 per cent natural gas will explode, or propagate flame throughout the mixture without the continual presence of the source of ignition that started the inflammation. The table following gives the explosive limits of the common combustible gases and air:"

Jun 1, 1926

By John H. Johnson

This report covers research which is directed toward the measurement and control of underground mine diesel emissions. The report consists of three separate reports presented as Sections 1, 2, and 3. Section 1 "Emissions Measurement Apparatus" (EMA 1) discusses the selection and evaluation of instruments and procedures to be used as part of a diesel tailpipe emissions dilution and measurement apparatus. The instruments selected for gaseous pollutants are the Energetics Science Inc.* E.S.I.) 2000 for CO, the E.S.I. 7000 for NO and N02, and the Fuji ZFP5 for C02. Particulate matter is presently measured with the Celesco 1013 Smoke Opacity Meter. The raw exhaust concentration of one of these constituents is used Lo calculate the dilution ratio. Either a modified high range E.S.I. 2000 CO instrument or a Daco Products Cobra C02 instrument can be used, but neither is totally satisfactory. The study also indicated that it may he possible to increase the sample collection time from 15 seconds to the total 30 seconds over which the engine can be loaded without increasing the probability of damaging the vehicle hydraulic systems. Section 2 "The Effect of Fuels, Catalysts and a Filter Trap on Drift Pollutant Concentrations" discusses research in the Mine Air Quality Laboratory. A Wagner ST5D LHD with a Deutz F8L714 engine was used to compare three exhaust aftertreatment devices and a muffler-only system. The effect of these four systems on CO, C02, NO and N02 and on total, soluble, sulfate, and solid particulate matter was measured in the drift and on the LHD. The filter trap successfully reduced particulate matter for both fuels without significantly increasing the concentrations of any of the other constituents. The PTX catalyst was effective in reducing CO, and soluble particulate, but significantly increased N02 and solid and sulfate particulate matter. The Oxy Cat catalyst tested didn't seem to he working on the gases, and it significantly increased sulfate, soluble arid solid particulate concentrations. Section 3 "Diesel/Coal Particulate Matter Characterization by Laser Raman Spectroscopy" covers basic research on a method for determining the percentage by weight of diesel particulate on a filter containing a diesel-coal mixture. Signal-averaged Raman spectra provide the necessary precision. The method developed is non-destructive and uses as-received filters requiring no sample manipulation. Particulate with diesel contents in the range of 10 to 50% by weight have been analyzed with accuracies better than 6%t of the mean value. A number of samples containing diesel-coal mixtures were characterized by the procedures developed and the results are analyzed in light of various spectral and other system variables including coal rank and form and diesel engine operating conditions.

Jan 1, 1982