Search Documents

Develop an easy-to-use, reliable, resin-grouted cable support system capable of being installed as primary and secondary roof support in coal mines.

Jan 1, 1994

By Oliver Bowles

As the preface states, this bulletin is the fourth of a series of re- ports by the Bureau of Mines on different phases of quarrying in the United States. The first part of the bulletin describes the chief types of cements, the growth of the cement industry in this country, and the character of the raw materials used. The bulk of the report deals with quarrying methods and equipment, and gives especial attention to drilling and blasting; a chapter on rock mining and one on pros- pecting are included. Methods of manufacture are mentioned briefly, as that subject, except as related to quarrying, lies outside the scope of this report; but transportation methods and the effects of the man- ner of mixing the materials at the quarry or crushing plant on quarrying methods are discussed.

Jan 1, 1918

By Lloyd A. Morley, Robert Stefanko

The most time-consuming research segment was assembling the ref¬erences. These are provided immediately after the conclusions but are divided into two categories. The first is directly applicable publi¬cations, correspondence and personnel communications. The second listing contains those publications that are not directly tied to the research but where a probable application exists. In both listings, all important USBM publications are provided. The reference numbers used in the report apply only to the first reference portion. Further¬more, it should be noted that all entries are not used but are retained to help anyone who wishes to look further into different or allied areas of this research topic. Explosion-proof enclosures have been researched since approxi¬mately 1906. Even so, little is understood about the mechanism by which they are effective. Due to the voluminous literature published, there is a good probability that the assembled list is still incomplete. The literature search took the following directions. Work was first directed to reviewing the several references assembled by the Department of Mineral Engineering - Mining Section prior to the present project year. As a result, some duplications and inapplicabilities were found and eliminated. The primary sources of the previous search were the commonly available and usually superb library listings, such as Engineering Abstracts. Because these sources have enormous content on all subjects, they were cross-checked in the first semiannual period several times by different individuals to make sure all normally avail¬able literature were uncovered.

Jan 1, 1974

By R. V. Ramani, A. S. C. Owili-eger

The Methane Generator program is a part of the Internal Environ¬mental Sub-system of the Master Design Simulator (MDS). All the sub¬systems of the MDS are controlled and activated by the main program as required. The data requirements for the Methane Generator are supplied by the Geology and Reserves sub-system through common storage. Figure 6 shows the information flow between the Methane Generator and other systems of the MDS. It should be noted that the Methane Generator can also function independently as was described under model application. AREAS OF MISSING INFORMATION In any numerical analysis, the accuracy of the solution depends entirely upon the data available. In gas flow problems, parameters that constitute basic model input data are rock porosity, medium permeability, reservoir pressure and initial reservoir pressure dis¬tribution. Unfortunately, however, most of these characteristics are not available for a lot of coal seams. The need for actual field data cannot, therefore, be adequately emphasized here.

Jan 1, 1974

Objective: Construct a research facility to test sensor technology and engineering controls and to increase awareness of the proper functioning of mine hoists. Improve saferty and prevent injuries and fatalities to vertical movement of personnel and meterials in mine shafts and ore passes.

May 1, 1997

By Dennis Dolinar, Russell Frith, David Oyler, Christopher Mark

Unusual circumstances may require that a longwall retreat into or through a previously driven room. The operation can be completed successfully, but there have been a number of spectacular failures which exposed miners to serious roof fall hazards. To help determine what factors contribute to such failures. the National Institute for Occupational Safety and Health (NIOSH) compiled a comprehensive international database of 130 case histories. The cases include five failures where major rock falls occurred in front of the shields, and six even more serious failures involving major overburden weighting. This suggests two room failure mechanisms The first is a roof fall type failure caused by loading of the immediate roof at the face as the fender narrows. The second is a weighting type failure caused by the inability of the roof to bridge the recovery room and face area, and affecting rock well above the immediate roof The data indicate that the roof fall type of failure is less likely when intensive roof reinforcement (bolts, cables, and trusses) is employed together with higher-capacity shields The overburden weighting failures, in contrast, occurred when the roof was weak and little standing support was used

By J. S. Peterson, G. P. Cole

The National Institute for Occupational Safety and Health (NIOSH), Pittsburgh Research Center (PRC), has conducted research to improve electrical fault detection on coal mine direct current (dc) trolley systems. Present circuit breaker protection systems are current-magnitude-based and cannot discern between normal traffic and high resistance electrical faults. Tests were conducted at cooperating mines to assist in developing a neural-network-based detection algorithm for distinguishing between electrical faults and normal operation. The Fast Fourier Transform of the trolley rectifier current signature served as baseline data for the neural network. During field tests, the algorithm performed with greater than 90% accuracy.

Lower the respirable dust exposure of longwall shearer operators by use of a modified head to tail cutting sequence. Approach Modify the cutting sequence of double-drum shearer operations cutting unidirectionally head to tail, so that the tailgate drum is used to mine the entire coal face except when cutting out at the head. This approach would place the primary dust generating source, the cutting action of the drum, on the return air side of both shearer operators. How It Works Currently, 75% of the double-drum shearers in operation employ a unidirectional cutting sequence. On half of these operations, the primary cut is taken as the shearer travels from the headgate to tailgate ends of the face, with roof support to be advanced on the intake air side of the shearer. Typically, the leading (tailgate) drum is taking a full cut during the head to tail pass and the trailing (headgate) drum is cutting bottom coal. In this mode of operation, the dust generated by the trailing (headgate) drum can spread out into the walkway, and increase the respirable dust exposure of both head and taildrum operators. As an alternative, if the trailing drum is "free wheeling" or cutting minimal coal during the head to tail cut, and bottom coal taken by the tailgate drum during the tail to head clean-up pass, both operators are able to work on the intake air side of the primary dust generating source (drum) except when cutting out at the head. This modified cutting sequence would save wear on the conveyor and help to eliminate overloads, as well as reduce the respirable dust exposure of both shearer operators. This modifcation is only applicable to long-wail operations currently cutting unidirectional head to tail, and to those operations where this unidirectional cut would not produce operating constraints.

Jan 1, 1981

By Frederick C. Trutt, Jeffery L. Kohler, Joseph Sottile

Condition-based maintenance (CBM) of industrial equipment is generally recognized as being the most cost-effective means for improving equipment availability. However, prerequisite to successful implementation of CBM is a reliable detector of failing components. One such detector, termed the effective negative-sequence impedance, had previously been identified as an indicator of induction motor stator winding degradation. However, a limitation of this detector is that it does not change in a predicable manner under certain motor operating conditions. This paper presents an experimental investigation of an improved technique for on-line detection of induction motor stator winding degradation. The paper begins with a brief description of the detectors, followed by a detailed description of the experimental setup, the experiments conducted, and results.

To improve operational effectiveness of enclosed cab filtration systems. Background Enclosed operator cabs are widely used on mobile excavation equipment in the mining and construction industries. They protect the operator from bad weather, noise, and airborne dusts. The inside cab environment usually must be kept at very low dust concentrations because of quartz dust generated from the excavation of silica-bearing rock. Most cab designs achieve heating and air conditioning effectiveness by recirculating most of the interior cabin airflow, with a smaller portion of the outside air added to the cab as makeup air. Both the recirculated cab airflow and exterior makeup air added to the cabin should be efficiently filtered, with the makeup air positively pressurizing the cab interior. Ideally, operator cab air filters should provide at least 99% capture efficiency for dust particles as small as 0.3-pm aerodynamic diameters. These higher efficiency air filters provide good dust control for the equipment operator, but tend to accumulate dust more quickly than lower efficiency air filters.

Jan 1, 2001

By Donald P. Tuchman

The U.S. Bureau of Mimes is investigating Fourier transform infrared (FTIR) spectroscopy for on- filter quartz analysis of respirable dust. A custom accessory is described for full-face examination of filters utilizing a large-diameter infrared (IR) beam. The accessory positions samples to match diameters with that of the diverging analytical beam. Sample absorbance is then measured. With nonuniform deposition of dust on collection filters being a major issue for such analyses, this approach is the most direct way to accomplish sample area averaging. The approach is unconventional since it utilizes large-beam geometries instead of the usually desired minimized beam dimensions. The issues and problems involved in the analysis of quartz on a filter matrix are discussed. Absorption bands chosen, light-scattering effects, curved baselines, random noise, interference fringes, and possible solutions to technical difficulties are the topics covered. The more significant findings include a 20-pg detection limit for quartz when the custom accessory is used and minimal occurrence of light-scattering effects at low wavenumbers. The custom accessory performance was satisfactory and merits further work. With continued research, an on-filter method for quartz analysis of respirable dusts seems achievable.

Jan 1, 1992

By Mark S. Stagg, Virgil J. Stachura, John W. Kopp, David E. Siskind

The Bureau of Mines studied airblast from surface mining to assess its damage and annoyance potential, and to determine safe levels and appropriate measurement techniques. Research results obtained from direct measurements of airblast-produced structure responses, damage, and analysis of instrument characteristics were combined with studies of sonic booms and human response to transient overpressures. Safe levels of airblast were found to be 134 dBL (0.1 Hz), 133 dBL (2 Hz), 129 dBL (6 Hz), and 105 dB C-slow. These four air- blast levels and measurement methods are equivalent in terms of structure response, and any one could be used as a safe-level criterion. Of the four methods, only the 0.1-Hz high-pass linear method accurately measures the total airblast energy present; however, the other three were found to adequately quantify the structure response and also represent techniques that are readily available to industry. Where a single airblast measuring system must be used, the 2-Hz linear peak response is the best overall compromise. The human response and annoyance problem from airblast is probably caused primarily by wall rattling and the resulting secondary noises. Although these will not entirely be precluded by the recommended levels, they are low enough to pre- clude damage to residential structures and any possible human injury over the long term.

Jan 1, 1965