Search Documents

Develop a reliable, portable device for non-destructively testing the support integrity of a friction rock support (commonly referred to as a Split Set ). Approach The friction rock support, used to support mine roof and ribs, is a slotted tube driven into a drilled hole of smaller diameter. Upon installation, the tube is compressed radially. The amount of compression is a function of the hole diameter, the strength of the host rock, and the properties of the split set itself. A simple lightweight self-contained device was developed to determine the pull-out resistance of the friction rock supports in-situ, based on measurements of the tube's deformation. The tester measures the com-pressed internal volume of the slotted tube, which has been found to provide an estimate of the support's resistance to pull out. How It Works The tester consists of a pump and expander sections. The expander sections are made from an elastomer membrane which is stretched over two cores, each one inch in diameter and twelve inches long. The expanders are connected by a flexible coupler so that they can fit any alignment of the support.

Jan 1, 1984

By R. V. Ramani, R. Stefanko, G. W. Luxbacher

MINE VENTLATION NETWORK ANALYSIS

Jan 1, 1977

By R. E. Head

[Surveys of the manganese situation conducted by the Geological Survey and other agencies have distinctly established the fact that the tonnage of high- grade manganese ore in the United States is relatively small. It is therefore obvious that large-scale production of manganese is possible only through beneficiation of low-grade material. ]

Jan 1, 1941

Reduce the dust exposure to the operator of a longwall shearer with a novel foam spray system. Approach Discharge foam through the nozzles of a shearer drum so that foam and coal are better mixed. How It Works Bureau of Mines research showed that two very important principles for successful application of foam are: (1) moisture distribution and (2) degree of mixing. Foam can distribute a given quantity of moisture much more evenly over a large surface area. Successful Bureau tests of foam for dust control always involve a high degree of mixing between the foam and the material, Mixing, permits a greater distribution of foam throughout the mined product. The most suitable location of foam application would be at the point where the dust is generated, before the dust becomes airborne. Foam nozzles located in the cutter drum (pick face foaming or ejecting foam through scroll sprays) will suppress dust close to its source.

Jan 1, 1989

By John S. Dunning

This is one of a. series of papers being prepared for and published by the United States Bureau of Mines, describing raining and milling methods at crushed-stone plants throughout the United States. These papers are designed to disseminate technical information regarding the methods used. The cost tabulations represent operating expenditures only and not total production costs. It is recognized that publication of total production costs might in man; instances cause embarrassment to individual producers as well as to the industry as a whole. However, operating costs are essential to technical discussion and study of the methods employed. The attention of the reader is specifically called to this differentiation in order that the scope of the cost tabulations shall not be misunderstood. This paper deals with the quarrying and crushing methods used at the Avon Mountain trap-rock quarry of the Atlas Sand, Gravel & Stone Co., in West Hartford, Conn.

Jan 1, 1936

Provide better ventilation for mines by reducing air leakage around stoppings. Approach Most stoppings are constructed of concrete blocks and trowelled-on mortar and are not very airtight. Bureau of Mines research has shown that brushing on modified mortar containing fiberglass and/or other additives, that enhance strength and adhesion, minimizes air leakage around and through the stoppings. Airtightness is an important factor in building stoppings since an airtight stopping will provide for more efficient ventilation airflow and more cost-efficient use of the mine's ventilation system. How the New Technique Works After broken floor and rib material is removed, the stop-ping faces are covered with one or two coats of modified

Jan 1, 1982

Capture airborne coal dust generated by a continuous mining machine to reduce workers? dust exposure and to improve face visibility. Approach Develop a low-profile dust collector system which can be mounted on the boom of a continuous miner. How It Works When coal is mined with a milling head continuous miner, a substantial amount of coal dust (respirable and non-respirable) escapes the dust suppression sprays at the cutter head. This can cause poor visibility around the cutting head and can expose the workers to high levels of respirable dust. A practical means of removing this dust is with a scrubber mounted directly on the mining machine. Under a Bureau of Mines contract, a low-profile, machine-mounted dust collector (MMDC) was developed to avoid adding extra height to the continuous

Jan 1, 1983

By R. W. Nash

This report describes the design and operation of a digital instrumentation package for the Bureau of Mines improved torsion pendulum, a scientific instrument that measures the vibration damping of metallic materials. The new design eliminates manual analog-to-digital conversion, reduces the data acquisition time, and increases the precision of the measurements. The digital output can be coupled directly to a micro-processor or computer to produce the final data in real time.

Jan 1, 1983

Reduce the noise radiated by the auger miner cutting head (typically 105 dBA at the face) by 10 dBA without compromising the durability or productivity of the tool. Approach Research was conducted by the Bureau of Mines to identify the noise sources of auger miners with emphasis on the cutting head and coal cutting process. The overall noise level generated by the coal cutting process was found to depend greatly upon the structural characteristics of the auger cutting head. Based on this information, a quieter cutting head was

Jan 1, 1982

Enable mine personnel to determine the effectiveness of and to optimize the mine fire stench warning system without resorting to costly trial and error fire drills. Approach The mine fire stench warning system is used by underground metal/nonmetal mines to warn mine workers of a fire or other emergency. Stench is released directly into the mine ventilation and/or compressed air lines, and its repulsive odor warns miners to evacuate the mine or to follow other established emergency procedures. Unfortunately, since most deep metal mines have complex ventilation systems, some areas of the mine may receive nauseatingly high concentrations of stench while other areas, in more remote locations, may receive no warning or greatly delayed warring at best. The Bureau of Mines, through research, endeavored to solve this problem with a computer modeling system designed to calculate the distribution of odorant by the stench warning system.

Jan 1, 1986

By Robert F. Holub

The Bureau of Mines has made a study of the magnitude of the variations of radon daughter mixtures, with the objective of determining whether these variations reflect the existing physical conditions in uranium mine atmospheres or if they are merely random or systematic errors. To accomplish this, many data have been plotted using a triangular graphing technique which shows that plateout affects RaA more than RaB or RaC, and that it is impossible to find simple correlations between working level ratios, radon daughter mixtures, and age.

Jan 1, 1978

By W. M. Weigel

"The use of sand for the filtration of municipal water supplies is comparatively recent use in this country, although at the present time, most cities of any size that draw their water supply from surface sources use sand filters in their purification system. Not only are sand filters employed to remove sediment and suspended matter, but they also take out most of the bacteria in the water.The first comprehensive research and study of sand for this purpose was probably that of Hazen for the Massachusetts Board of Health in 1891 and 1892, although sand filters had been employed for a considerable time before, specifications for filter sand drawn since then have been largely based on the results of Hazen's work,The general requirements for filter sand are more exacting than for any of the different kinds of sands, except the chemical specifications for glass sand. Filter sand must be uniform in size and within certain limiting sizes. In addition, it must be clean and free from clay and organic matter and of fairly high purity. Early investigations established the fact that an excess of fine materiel increased the friction and decreased the rate of flow through the filter, and that the size of the finer particles rather than the courser, determined the effective size. Also, that large grains tended to cause irregularities in flow in different parts of the bed. There is no requirement as to grain shapes, except that they be not flat or elongated, since, so far as known, either rounded or angular grains are equally efficient.Based on Hazen's investigations, two factors are quite generally used to control the average size and uniformity of size of the sand. These are defined as follows: The ""effective size"" of a sand is such that 10 per cent by weight of the seed is finer than this size, end 90 per cent is coarser. It is expressed in millimeters, The ""uniformity coefficient"" is defined as the ratio of the size of grain which has 60 per cent finer than this size to the size which has 10 per cent finer (the ""effective size""). It is evident that the smaller this coefficient, the more uniform is the seed. If all the grains were exactly the same size, the coefficient would be 1."

Jul 1, 1924

By David R. Forshey

This Bureau of Mines report presents a quantitative theoretical analysis of a coupled gasdynamics-heat release system involving the kinetics of water condensation in and behind the rarefaction wave in a shock tube using the method of characteristics. The merger of characteristics to form a shock wave is included.

Jan 1, 1977

By G. H. Schnakenberg

In response to the underground mining industry's growing concern with the exposure of workers to the diesel particulate matter (DPM) component of diesel exhaust, a method was developed to estimate the average workplace concentration of DPM that could be expected from using the new lower DPMemitting engines now being approved by the US Mine Safety and Health Administration (MSHA) when these new engines are equipped with state-of-the-art exhaust-control, technology for filtering and combusting DPM. The resulting estimate uses the MSHA-reported particulate index for these engines, the prevailing rule-of-thumb ventilation rate of 150 cfm/hp and the available diesel-exhaust filter technology that has been shown to be at least 80% effective in reducing tailpipe DPM. In the estimate calculation, every engine used in an underground mine is assumed to be equipped with this control technology. Under the stated reasonable conditions, an average DPM level of 90 µg/m3 (mass) is predicted as technically feasible.

By T. O. Llewellyn

The Bureau of Mines conducted laboratory batch beneficiation tests on a waste granite sludge from New Hampshire to determine the feasibility of recovering a reusable silicon carbide product. The granite sludge responded to attrition scrubbing, desliming, and flotation in either alkaline or acid circuits using fatty acid as a collector. Recovery of over 80 percent of the contained silicon carbide at grades of up to 96 percent SiC was obtained.

Jan 1, 1975

By P. W. Jeran

The Beckley mine is one of five new mines in a heretofore unmined portion of the Beckley coalbed. The remoteness of these new mines from prior mining and their greater overburden preclude applying methane emission experience obtained in the old mines. Four sections of the Beckley mine were monitored. The data gathered show that variations in methane emission cannot be explained by variations in coal production. Although overburdens varied by as much as 30 pct, no correlation with methane emissions could be determined. The rib emissions increase with increased length of rib from a section advancing into virgin coal and do not decline over a prolonged idle period (32 days) whereas some decline has been measured for a section not mining into virgin coal. The indication is that degasification prior to mining will reduce the hazard of methane emissions in this area of the Beckley coalbed.

Jan 1, 1977

This volume summarizes the contract work performed over a nine-month period by Westinghouse Electric Corporation on a Cost Plus Fixed Fee Contract for the Department of Interior's Bureau of Mines. The contract has been extended primarily to carry out improvements recommended for equipment produced under the contract for communicating with and locating trapped miners. These improvements will enhance the performance and utility of this equipment for operational use in actual mine emergencies. An additional complete set of the equipment will also he furnished to the Bureau under this extension. The work of the basic contract was to design, produce and test hardware in accordance with the Westinghouse response to a Bureau of Mines Request for Proposal which was based technically on recommendations of a study performed for the Bureau by the National Academy of Engineering (NAE). The NAE study made suggestions for new equipment in three areas of need:

Jan 1, 1971

By P. A. Bloom

Arsenic-containing flue dusts are currently being stockpiled by several nonferrous smelters in the United States. These stockpiles are a source of environmental concern since the dusts can be transported by wind and contain water-soluble arsenic. The stockpiles also represent an alternate source of metals. To provide a quality environment, the Bureau of Mines investigated a process to make environmentally acceptable the discard of arsenic obtained from the treatment of arsenical flue dust. The process includes (1) leaching arsenic from a lead smelter copper dross flue dust, (2) fixing arsenic as an insoluble compound, and (3) recovering other metal values. Overall results of acid-leaching tests on lead-smelter flue dusts showed that H2S04 dissolved 80 to 90 percent of the As, Zn, and Cd, and up to 86 percent of the In. Pb, Ag, and Au remain in the residue, which can be recycled to the smelter. Indium was recovered from the strong acid leach solution by solvent extraction; arsenic was fixed in a stable form by precipitation with Fe2(S04)3 and CaO or CaC03.

Jan 1, 1982

By Ryron O. Pickard

"The Berkeley safety station of the U. S. Bureau of Mines was recently informed that a geologist was killed through entering an abandoned 90-foot exploratory shaft without making a preliminary test of the shaft atmosphere. He was one of a geological party which was investigating coal lands in California. The only light that he carried into the shaft was an electric flash light. After he had descended a short distance, one of his associates on the surface heard him exclaim, ""This place is full of gas, I am coming up"", He had no more than finished the remark when he was seen to lose his grip on the ladder and fall down the shaft. He was apparently weakened from impure air in the shaft, and could no longer suppers himself on the ladder. When his body was recovered, it was found that his neck had been broken by the fall.This is the ;second recent accident that has been called to the writer's attention where a life has been lost in abandoned exploratory workings; the other fatality being in Minnesota where a mining engineer was overcome while sampling a shallow pit in iron-ore formations. This engineer was on the bottom of the shallow pit and died before help could reach him. It was generally supposed that each of these deaths were due to poisonous gases, but the writer believes, after reviewing the information available, that death in both instances may have been directly caused by deficiency in oxygen.Frequently in the daily press there are items relative to lives being lost through cleaning out old wells, and as a general rule such accidents are also caused by impure atmospheres.In every abandoned shaft or pit, or in fact, any old working where the air has been stagnant for a considerable time, there is always danger of oxygen deficiency, as the oxygen which originally comprised one-fifth of the atmosphere may be appreciably replaced by gases that do not support life, usually by carbon dioxide (black damp) or methane (fire damp). Much valuable information on the subject of mine atmospheres, mine gases, and the effect of oxygen deficiency onthe human system is contained in Miners' Circular 14, ""Gases Found in Coal Mines"" by G.F. Burrell and F. M. Seibert; Technical Paper 122, ""Effects of Oxygen Deficincy on Small Animals and Men"", by G. A. Burrell and G. G. Oberfell; and ''Chit of Properties of Mine Gees"" by G. A. Burrell. These publications of the Bureau of Mines should be rent by all who are interested in the subject of this paper."

Nov 1, 1921

By D. E. Hirsch

The Bureau of Mines has developed a systematic procedure for separation, characterization, and semiquantitative analysis of high-boiling (350° to 550° C) distillates of crude oils. Isothermal and molecular distillation were used to prepare the 370° to 530° C distillate of Recluse, Wyo., crude oil. The distillate was separated into fractions by chemical treatment, silica-alumina gel adsorption, and gel permeation chromatography (GPC). The fractions were analyzed by use of GPC correlations and mass and nuclear magnetic resonance (NMR) spectrometry. The increased knowledge of petroleum composition obtained from the data will contribute to improved petroleum processing and utilization and energy conservation.

Jan 1, 1974