Search Documents

By John W. Frey

This paper presents one of a series of digests of foreign mining legis- lation and court decisions which is being prepared in advance of a general re- port relative to the rights of American citizens to explore for minerals and to own and operate mines in various foreign countries. This interpretation of the laws of Portugal, prepared from the best available information in Washington, has been slightly amplified in accordance with suggestions trans- mitted through the courtesy of the Department of State by Fred Morris Dearing, American Minister at Lisbon.

Nov 1, 1929

By J. S. Hansen

The U.S. Bureau of Mines developed a system for casting unique, slotted steel armor by modifying the conventional expendable pattern casting (EPC) process that is normally used for making aluminum castings. Three innovations were added to the EPC process to make the successful adaptation: (1) Vacuum was applied to sand molds, (2) continuous narrow-necked feeding systems were used to permit the casting of thin walls, and (3) fixtures were designed to prevent pattern damage and to hold critical casting tolerances, Potential problems and defects are described.

Jan 1, 2010

By E. W. Pehrson

In making any canvass of secondary metals great care must be exercised to avoid duplication or exaggeration of net consumption. One of the major difficulties is to trace the metal accurately as it passes through the many cycles of manufacture. Greater or less duplication probably occurs in any canvass. The manufacturer of tin plate, for instance, purchases primary pig tin exclusively as a raw material. Most of it goes into the coating on the steel sheet, but a substantial part emerges in the form of byproducts such as scruffs and drosses. These are sold to other plants, where they are used in the manufacture of alloys and chemicals. Alloys and chemicals, however, are not necessarily articles for final consumption. The alloy may be sold in ingot form to a bearing manufacturer, who, in turn may produce some scrap, which he may sell to still' another plant that may make still other products. There is a considerable return of tin in the form of waste products from chemicals sold to the silk industry. Even tin plate does not represent an ultimate use of tin because the tin-can maker produces large amounts of clippings, which are sold to detinning plants, where the tin is recovered and used again for some other purpose. Thus the degree of duplication in consumption statistics depends on the point in the industrial cycle where consumption is measured.

Jan 1, 1936

Validate the premise that there is measurable seismic activity associated with abandoned mint lands and that this activity can be used to determine stability of the abandoned mine openings, failure cycle of these openings, and susceptibility of the area to surface subsidence. Approach The U.S. Bureau of Mines conducted field investigations at two geologically contrasting sites, Colorado Springs, CO, and the Allegheny Portage Railroad Historical Site near Cresson, PA, to demonstrate that developing monitoring technology can be applied to any site. An array of seven geophones (velocity-measuring sensors) were strategically located to encompass an area at each site where failure in the underground mine openings could be expected, based on historical, geological, and engineering information. How It Works Bureau research has effectively demonstrated that stress changes within a rock mass can stimulate the development of cracks and fractures, resulting in the release of strain energy that generates seismic waves. These seismic waves, traveling outward from their source, can be detected, and the point of origin can be located in three-dimensional space. Furthermore, these seismic signals contain information that defines the source mechanism and the conditions between the source and the receiving sensor.

Jan 1, 1992

By Mary S. Esfandiary

U.S. scientists attempting to maintain continuous surveillance of scientific information are confronted with two acute problems: The steady, even spectacular; increase in the volume of such information and the fact that much of it is published in unfamiliar foreign languages, According to the National Science Foundation, almost one-third of the world's scientific literature is published in languages that are read by less than 5 percent of U.S. scientists. Most scientists in the United States must rely on abstract journals and translations to obtain information on developments in research and investigations conducted in the non-English-speaking countries. However, there are problems involved in procuring suitable abstracts and translations and in obtaining such information as cheaply and rapidly as possible.

Jan 1, 1961

Control dust generated during overburden drilling at surface coal mines using either wet suppression or dry collection systems. Approach For the wet suppression systems, a range of water flow rates was tested over a number of holes. Each hole was drilled at a specific and constant flow rate. A recording flow meter was mounted in the water line near the control system pump. For the dry collection systems, each drill was tested with the front of the shroud set at different heights above the ground. Because of the irregularity of the ground surface, all height measurements were taken at the front of the shroud. Background Wet drilling systems consist of a water tank mounted on the drill from which water is pumped into the downhole air line. The water droplets in the bail air conglomerate dust particles as they travel up the the annular space of the drilled hole, thus controlling dust as the air bails the cuttings from the hole.

Jan 1, 1987

To develop an explosive charge that will effectively break rock in underground mines and that can be safely fired without the use of blast-holes or the need for stemming. Approach The Bureau of Mines developed a non-incendive, cylindrically-shaped explosive charge that will not ignite gassy or dusty atmospheres, even methane-laden air. How It Works Firing unconfined explosive charges in underground mines is prohibited by law since detonation in gassy or dusty atmospheres is extremely dangerous. However, there are advantages in using unconfined charges from both a safety and a production standpoint. Explosives can effectively break up large boulders, rocks and slabs when leveling roof falls and can dislodge overhangs which miners would other-wise have to dislodge manually, exposing themselves to

Jan 1, 1983

Provide a means of recovering precious metal values from finely ground tailing materials. Approach Determine the procedures needed for agglomerating the finely ground material for subsequent heap-leach cyanidation of the precious-metal-bearing tailings. Applying Agglomeration/Heap-Leaching to Fine Tailings Agglomeration technology was developed by the Bureau of Mines to provide cost-effective recovery of precious metal values though better heap leaching of clayey or low-grade ores. While many precious metal producers have adopted this technology to reclaim precious metals from crushed ores and wastes, other operations have experienced problems in using the heap leaching technique effectively on piles of fine tailings. In contrast to the coarser ore and waste material, most tailings piles contain more than 50 percent minus 200 mesh materials with no coarse material. Fine particles and clays present in the pile can impede 8 uniform flow of the leaching solution through the heap, thus preventing efficient and cost-effective precious metals recovery.

Jan 1, 1986

By Vijia K. Karra, John J. Sammarco, Robert Paddock, Edward F. Fries

Workers in hazardous environments such as mining are constantly exposed to the health and safety hazards of dynamic and unpredictable conditions. One approach to enable them to manage these hazards is to provide them with situational awareness: real-time data (environ-mental, physiological, and physical location data) obtained from wireless, wearable, smart sensor technologies deployed at the work area. The scope of this approach is limited to managing the hazards of the immediate work area for prevention purposes; it does not include technologies needed after a disaster. Three critical technologies emerge and converge to support this technical approach: smart-wearable sensors, wireless sensor networks, and low-power embedded computing. The major focus of this report is on smart sensors and wireless sensor networks. Wireless networks form the infrastructure to support the realization of situational awareness; therefore, there is a significant focus on wireless networks. Lastly, the “Future Research” section pulls together the three critical technologies by proposing applications that are relevant to mining. The applications are injured miner (person-down) detection; a wireless, wearable remote viewer; and an ultrawide band smart environment that enables localization and tracking of humans and resources. The smart environment could provide location data, physiological data, and communications (video, photos, graphical images, audio, and text messages).

Jan 4, 2007

By D. E. Shanks

As part of its effort to produce cell-grade alumina from clay, the Bureau of Mines investigated the hydrogen chloride gas-sparging crystallization of aluminum chloride hexahydrate (ACH) from aluminum chloride liquor, to provide information for optimizing the crystallization operation. Four parameters important in controlling the crystallization of the aluminum chloride hexahydrate and the concentration of impurities, particularly phosphorus and magnesium, in ACH crystals are (1) aluminum chloride concentration in the feed solution to crystallization, (2) hydrogen chloride gas flow rate, (3) temperature, and (4) concentration of phosphorus and magnesium also in the feed solution. Parameters 1, 2, and 3 affect crystal formation. The combined effects are very important because the phosphorus and magnesium concentrate in the crystals during the early stages of crystal growth. Aluminum chloride hexahydrate of cell-grade purity was crystallized from saturated aluminum chloride solutions containing less than 0.003 wt-pct P205 and 0.010 wt-pct MgO. Crystallization temperatures less than 600 C decreased crystal purity.

Jan 1, 1981

Reduce dust at the auger mine face by modifying airflow patterns, around the minim machine. Approach Limited clearance between an auger miner and the mine root restricts airflow across the face and causes dust rollback. Directional sprays arc used to direct air across the face, thereby reducing dust rollback and increasing dust dilution (fig. 1). Laboratory and underground studies were used to test and optimize effectiveness of the directional sprays. Results of Laboratory Study Laboratory experiments were conducted in a simulated auger gallery equipped with a full-scale mock auger miner and bridge conveyor. A dual curtain configuration was used to direct the, ventilation, which averaged 2,700 cfm throughout the experiment. Testing variables included spray location, pressure, spacing, orientation, and number. Figure 2 shows the optimized directional spray system, also called the auger clearer spray system. The system consists of three sprays mounted alone the intake side of the miner. Sprays arc spaced 16 to 24 inches apart, and angled 30° toward the return side of the miner. The 24-inch spacing moved about 7% more air across the face than the 16-inch spacing; however, it resulted in some additional misting on the return side of the miner. A 30° orientation was more effective than a 60° orientation for moving air across the face and minimizing misting on the return side of the miner. Flat fan sprays arc used because their spray paths arc not obstructed by the top of the miner and mine roof, A 50° fan angle is used to minimize misting on the intake side of the miner.

Jan 1, 1989

By S. D. Maksimovic

The Bureau of Mines evaluated the hydraulic stimulation of a gob-degasification borehole to determine if this procedure would aid in degasifying a longwall panel. The stimulated borehole did not degasify the longwall panel as expected either before or after mining of the panel started. It reduced the underground methane emission only 11 pct, considerably less than the reductions effected by two unstimulated boreholes in the same panel. Some probable reasons for the reduced methane flow from the hydraulically stimulated borehole are very low reservoir gas pressure, location of hydraulically stimulated zones within the grouted casing, a casing break caused by lateral shifting, possible vertical movement of rock strata during caving, grouting of a 4-inch pipe blocking three stimulated zones, plasticity of shales, and possible hole damage by swelling of water-sensitive minerals. The borehole was also located between two second-mined areas, which may have allowed partial degasification of the overburden and the coalbed in advance of mining. Finally, a period of 3 months is probably not long enough for the borehole to degasify the overburden before mining.

Jan 1, 1977

By J. R. Allsup

The Bureau of Mines studied the characteristics of simulated coal gas as an automotive fuel in two multicylinder vehicles in a standard and high-compression-ratio engine configuration. While using simulated coal gas fuel, increasing the engine compression ratio improved the fuel economy and vehicle performance but increased hydrocarbon emissions by 40 pct. photochemical reactivity of exhaust hydrocarbons was found to be extremely low using the coal gas fuel. An oxidizing catalyst used with the simulated coal gas fuel eliminated all but trace amounts of carbon monoxide and reactive hydrocarbons in the exhaust. Spark gap geometry and firing voltage were varied and, within the range tested, had little effect on vehicle performance and emissions using simulated coal gas fuel.

Jan 1, 1975

By R. V. Ramani, J. M. Mutmansky, J. Qin, J. Organiscak, R. Bhaskar

"The results of a two—year research study into the relationship between quartz dust levels in host material and in respirable dust in continuous mining sections are presented in this paper. The experimental design and sampling procedures for underground data collection are outlined. The sample analysis procedures for quartz determination, the ¬analysis results and conclusions of the study are discussed.The results of the study indicate that the quartz contents of the airborne dusts are generally higher than those in the host material and bulk samples; and the quartz content increases with decreasing size of the airborne dust. The source for quartz appears to be the roof and the floor materials rather than the coal seam itself. It also appears that the material containing quartz may be breaking into a different size distribution than coal.INTRODUCTION Without doubt, the potential for permanent and severe health damage exists due to respirable dust in the work environment. The attention directed at the reduction of respirable airborne dust to levels below those specified in the law and the achievements to date in meeting these standards are but a reflection of the recognition by many parties government, industry, and labor - of this potential and the need to reduce it.The ambient dust standard in underground U.S. coal mines (2 mg/s3) has a qualifier (Code of Federal Regulations, Title 30, Part 71.101) to determine an applicable dust standard when a respirable dust sample contains more than 5% quartz. This standard is frequently referred to as the ""reduced standard."" The reasoning behind the reduced standard is the relative toxicity of the quartz dust compared to that of pure coal dust. As the quartz levels in samples increase, the applicable standards become more stringent and maintaining the workings in compliance becomes increasingly difficult.The number of underground work locations operating under the reduced standards has shown a dramatic increase since 1980 (Figure 1). For comparison purposes, there were no mining entities operating on reduced standards prior to 1977. The emergence of this problem, which affects the health and safety standards on one hand and creates severe compliance problems on the other, has been rapid."

Jan 1, 1990

By Ronald D. Hill, Elmore C. Grim

The United States is richly endowed with mineral resources. However, mineral recovery by its very nature, involves a destructive process, Figures 1 and 2. In the past, mining practices were all too often conducted with the purpose of removing minerals by the simplest and cheapest method possible, without plans for the preservation of land, water, and air, and with too little consideration for the rights of others. A mining company is in business to make a profit, but every company, regardless of the nature of its business, has moral obligations to reduce its undesirable effects on the environment and to safeguard the rights of others. The problem of environmental degradation caused by surface mining is widespread and serious. Minerals in some form occur in each of the 50 States and several States are extensively mined. Data on the acreage disturbed in the United States, by commodity and State are presented in Table 1. Thirty-one States have laws regulating surface mining, (Table 2). Briefly reviewed in Appendix A-1 are the basic provisions of State laws governing surface mining. It can be seen that these laws vary considerably from State to State owing largely to the mining conditions within that State. Of the 24 coal-producing States, only three (Alaska, Arizona, and Utah) do not regulate strip mining. Even the states that are often cited as models of comprehensive regulations still have problems minimizing environmental damages. Uncontrolled surface mining presents a situation as critical to the well-being of the society as any it has ever faced. Many mining activities have imposed huge social costs on the public at large. These costs are long-range and are in the form of stream pollution, floods, landslides, loss of fish and wildlife habitats, unreclaimed land, erosion, and the impairment of natural beauty. In a 1965 Department of Interior study,(1)it was estimated that of the 25,000 miles (1+0,225 kilometers) of contour bench in Appalachia, approximately 1,700 miles (2735 kilometers) are affected by massive landslides. Additionally, 1+800 miles (7723 kilometers) of streams and 29,000 surface acres (11,716 hectares) of impoundments and reservoirs have been seriously affected by coal strip mining operations in the United States.

Jan 1, 1974

By John Durkin

Field studies have been conducted in a large number of coal mines throughout the U.S. to determine the effectiveness of electromagnetic techniques in locating men trapped underground following a mine disaster. Data from these tests have been used to generate models of expected signal and noise distributions as found above mines throughout the coal fields. These distributions have aided in placing the expected performance of a through-the-earth electromagnetic communications technique into a probabilistic framework. Results indicate an expected 45% probability of detecting a miner's signal from a depth of 1,000 ft, a depth which exceeds 903 of the coal mines within the U.S. and a 90% probability at a depth of 500 ft, a depth which exceeds 50% of the mines.

By Benjamin W. Haynes

The Bureau of Mines conducted research to devise technology for increasing the Nation's mineral supply by recovering valuable constituents from currently discarded waste materials. Municipal solid waste (MSW), presently a major disposal problem, represents a significant source of metals, glass, and a combustible fraction that can be used to supplement coal in generating heat and electricity. As part of the total metallurgical system to treat MSW, this study evaluates the combustible fraction of MSW to characterize the various combustible components and to identify the principal sources of elements that eventually may be objectionable from corrosive or environmental considerations. Several possible sources for cadmium, chromium, cobalt, copper, lead, nickel, and zinc have been tentatively identified. These sources are pigments, inks, paper stock, and additives to plastics. A correlation between industry consumption values and measured concentrations in MSW was found for several elements.

Jan 1, 1978

By Edmund S. Leaver

This information circular is written is response to the marry requests for information on the recovery, or reason for poor recovery, of fine gold by the amalgamation process. Checking Gold Content Experience has shown that in many cases error has been made because the true told content of a particular sample or deposit was not known. Fire assays of representative samples give accurate results and should be considered final in determining the gold content.

Jan 1, 1928

By Gregory J. Chekan

In This Chapter [Drilling, blasting, and crushers Diesel particulate Enclosed cabs Ventilation with jet fans Stopping construction methods Propeller fans as main fans] This chapter explains how to control dust in large-entry stone mines, including both silica dust and diesel particulate. Most stone mines are limestone mines, but a substantial minority are marble, sandstone, and granite mines. These mines differ from most others in that entry widths are 30 ft or more and entry heights are 25 ft or more. Such mines, developed with room-and-pillar methods, have large open areas that can make ventilation and dust control more difficult. Because of the difficulty of ventilating stone mines, improved ventilation is a major focal point of this chapter. However, the chapter also covers the control of dust from drills, blasting, and crushers. Another part of the chapter covers enclosed cabs, an effective dust control technique for some workers. BACKGROUND The major dust compliance problem in stone mines is caused by silica (quartz) in the rock. Mines in high-silica rock, 8% or more, are far more likely to have a dust problem than those where there is less silica. Geographically, the limestone in the Northeastern and South Central United States has higher silica than the rest of the country. Chekan and Colinet [2002] have analyzed Mine Safety and Health Administration (MSHA) dust sampling results [MSHA 2001] from the stone industry. They have concluded that, on average across the United States, the workers exposed to the highest dust concentrations are rotary drill operators, front-end loader operators, truck drivers, and crusher operators. However, there are many regional differences. Also, occupations that work outside of cabs, such as blasters, roof bolters, and laborers, can be exposed to high dust levels.

Jan 6, 2003

Provide a portable crushing capability to keep conveyor haulage close to the working face and permit more efficient and safer ore handling in low headroom, hardrock mines. Approach A readily portable jaw crusher is used which meets machine size, feed rock size, product size, and throughput requirements for low headroom, hardrock mines. How It Works The crusher is mounted on wheels to expedite frequent moves and to allow crushing of mined rock or ore near the working face. The crushed product is then placed on conveyor belts that are ex-tended as the crusher is moved. Keeping crushing and conveyor haulage near the face minimizes the haulage distances for trucks and loaders. Loading and haulage of run-of-mine ore is frequently the highest operational cost in underground mines. These costs can be significantly reduced by use of a belt conveyor, which is a common practice in coal and other soft mineral mines. The new low-profile hard rock crusher gives the same advantage of extensive belt haulage capabilities to low headroom, hardrock mines. The low-profile crusher will accept feed up to 30 inches when operating under 11 feet of headroom. The headroom required for crusher operation was reduced by tilting the jaws, feeding the crusher horizontally, and placing the eccentric shaft at the back or in a horizontal plane with the jaws. Material is fed by an

Jan 1, 1981