Search Documents

By Fred D. Wright

The objectives of this research were: 1. to determine the stability relationships of coal mine roof rocks which are cut by fractures or intersecting joints with and without roof bolts, under various sets of conditions including horizontal formation pressures, inclination and coefficient of friction of joints, bolt loads, roof spans and rock properties; and 2. to develop criteria for the design of roof bolt sys terns for such roofs. The problem was studied by mathematical finite element models and by laboratory models. From the results of the mathematical and laboratory models, equations were derived to express the relationships listed above for cracked, single-layered roof beams and design tables for such beams are included. The analysis was then extended to include multi-layered cracked beams reinforced by roof bolts and a method for analyzing and designing bolting patterns for such roof rocks is presented.

Jan 1, 1974

By W. H. Carrington, A. C. Richardson

"INTRODUCTION The Powhatan mine of the Franklin Coal Mining Co. is located in the western part of Jefferson County, Ala., on the Louisville and Nashville Railroad, 40 miles west of Birmingham. The Mary Lee bed at this point yields coal with fair coking qualities, but with an ash content as mined so high as to prohibit its use in the production of metallurgical coke. At present the entire output of the mine is washed in single-compartment jigs and marketed as locomotive and domestic fuel.Figure 1 gives a typical seam section of the Mary Lee bed at the Powhatan mine. This section shows that the bed is divided by rock partings into three benches. In many parts of the mine, particularly in the older workings the roof rock is so weak that it can not be held without excessive timbering. This condition has restricted the operation in many parts of the mins to the middle and bottom benches of coal. The 6 inches of draw rock between the top and middle benches is very strong and makes an excellent roof requiring only a normal amount of timbering to support it. In the newer workings of the mine the character of the rock above the top bench is strong and it is believed that in the future it will be possible to work all three benches. This study was undertaken for the purpose of determining the washing characteristics of the Mary Lee bed at Powhatan and the effect on these characteris-tics of including or omitting the coal from the top bench. It was also the purpose of the study to show whether it would be possible to produce a washed product sufficiently low in ash to be used for the manufacture of metallurgical coke. This paper is one of a series of reports on the washability of Alabama coals which is being prepared by the U. S. Bureau of Mines and tin University of Alabama. With the cooperation of the coal producers of Alabama. It contains the results of screen sizing and float-and-sink tests of representative samples of run-of-mine coal, and the results of table tests on the minus 3/16-inch sizes of the raw coal."

Apr 1, 1933

By Welby G. Courtney

The Bureau of Mines conducted an exploratory field survey to determine the amount of airborne coal dust, the size distribution of the dust, and the rate of dust deposition in coal mine airways. The survey was taken at eight underground locations in operating coal mines. The rate of dust deposition in the airways depended upon the concentration of air-borne dust and decreased exponentially with distance from the dust source. The rate was seemingly independent of the size of the airborne dust particles. The rate of deposition, along a return, for the coal dust from a fade being mined with a continuous mining machine closely matched the rate for the rock dust from a trickle duster. A sample rock-dusting schedule for that return is presented; that is, the trickle duster should be operated for 3-112 hours after every five shifts to protect the average deposit of new float coal dust in the return, but operation after every three shifts is preferred, to protect an occasional heavier deposit.

Jan 1, 1982

By David R. Peterson

This user's manual covers a set of 5 computer codes which were generated during development of a simulation of deep ocean mining operational economics. Table 1.1 provides a summary of these codes, and a more thorough description of each follows, In addition to the descriptions in this user's manual, internal documentation is provided throughout each code, except for the very simple ones, for ease of understanding or possible modification. The two major codes are MINER, which performs the deep ocean mining system operational simulation, and MSWEEP, which calculates the sweep and feed efficiencies for a set of collector paths generated by MINER. The standard operating procedure is to input the system and operating parameters to MINER, which computes a set of collector paths automatically and stores the information in the fife PATH.DAT. MSWEEP subsequently retrieves the collector path data in PATH.DAT, and uses it to calculate sweep and feed efficiency. Separating MINER and MSWEEP allows parmetric execution of MSWEEP without recomputing the collector paths with MINER. PIPEST, RESP, and OBSTCL are special-purpose codes described in more detail in the following documentation.

Jan 1, 1979

By F. W. Horton

Investigation of an extensive deposit of chromite-bearing actinolite-talc schist situated on the summit of Casper Mountain, 10 miles south of Casper, Wyo., was one of the first projects Undertaken by the Bureau of Mines under the Strategic Materials Act (Public 117, 76th Cong., Ch. 190, 1st sess.), for which an appropriation became available August 9, 1939. During the previous summer; the Geological Survey? made? a magnetometrical survey of the area in which the schist occurred. It was exposed in several small lenses and two larger ones aggregating about 19?acres in area. Although the occurrence of chromite here had been known for many years, the only work done on the deposit was the digging of? a few shallow pits on some of the more promising outcrops. From August 23 to December 3, 1939, the Bureau of Mines investigated the larger of the two main schist bodies. Twenty-four trenches having a total length of 8,073 feet were dug across the deposit, and its subsurface extension was explored by 3,623 feet of diamond drilling. Over 32 tons of samples were shipped to the Metallurgical Division of the Bureau of Mines at Reno, Nev., for reduction, analysis, and ore testing. In all, there were 853 individual samples. Geological maps, based upon examination of outcrops, trenches, and drill cores, as well as a contour map of the area were made by the Geological Survey.

Jan 1, 1949

By S. H. Ash

THE BARRIER-PILLAR SYSTEM in the Lackawanna Basin consists of 93 barrier pillars between Archbald and Taylor, Pa. These pillars affect 48 mines, have a total length of 87 miles, and confine 21 underground pools, which contain more than 10 billion gallons of water. From an investigation of size, position, and condition of the barrier pillars, it is apparent that those concerned are uncertain, not only as to the method by which the sizes of the barrier pillars were determined but also as to the stability of those that may be expected to act as dams. Where a barrier pillar must act as a dam, its failure may result in loss of life, the mine, or both; it would be far better had it not existed and thereby given a false sense of security.

Jan 1, 1952

By D. J. Hawk

The mechanical properties of coal are often represented by the orthotropicmaterial model, which consists of nine elastic constants. The material symmetries involved are found in coal primarily because of the natural process by which it was formed. In this thesis the material properties of five U.S. coals, as obtained from cubical testing, are examined, using as a basis for comparison the assumption of the orthotropic material model. An analysis is performed on each set of coal material data in order to examine its conformability to other, less complex material models, these being the transversely isotropic model consisting of five elastic constants and the 'isotropic model consisting of two elastic constants. In addition, the material properties of two American shales are analyzed, based on the assumption that they comply with the transversely isotropic model. An analysis similar to that performed on the coal material is applied to the shale in order to determine the conformity of its material properties to the isotropic model.

Jan 1, 1980

By William E. Bruce

The Bureau of Mines performed drill calibration tests on two industrial percussive drills of 2-5/8- and 3-1/2-inch piston diameters to determine operating characteristics for their use in conjunction with penetration rate data in developing drillability equations and furthering the knowledge of percussive drills. The use of a linear velocity transducer for measuring piston velocities and application of its instrumentation are described. Data presented include relationships between maximum piston velocity and feed air pressure other results confirm the theory or data of previous investigators, and some comparisons are made with the performance prediction formulas of other investigators.

Jan 1, 1969

By Anil Mahyera

Towards the goal of achieving uniform-high-tensions in roofbolts to provide superior roof support[1-7] for extended periods, Terra Tek installed mechanical-anchor bolts in a mine in eight different ways -- under torque/thrust control with and without hardened washers, belleville washers and tension equalization; in a conventional manner with and without a hardened washer. The various bolt groups were analyzed in terms of their tension uniformity and mean tension levels. Installing the bolts accurately with ? a hardened washer under the bolthead, and ? proper torque/thrust control resulted in the mast uniformly tensioned bolts -- with a coefficient of variation of only 14%, an improvement of 3 times over a conventional installation. Also, these bolts maintained a high tension level -- 80% of the installation tension, compared to 50% achieved conventionally.

Jan 1, 1982

By C. Haycocks

The problems caused by interaction in multi-horizon mining are world wide and are not limited to the coal industry. These problems will continue to increase as mining of new seams multiplies and replaces production from mined out horizons. Interaction problems are particularly evident in the Appalachian coal fields which contain many mineable, contiguously placed coal seams. Selection of the mining sequence of these seams, historically and currently, is based primarily on considerations of seam ownership, availability, and economics. Experience has shown, however, that mining any seam can seriously affect subsequent operations in coal seams both above and below the one being mined. This interaction effect is often detrimental to the recovery cost and safety of mining the subsequent seams. Designing to avoid or minimize interaction effects represents a major challenge to the modern coal mining industry and therefore is the focus of this research. In an effort to evaluate past interaction effects and provide guidelines for future mine design, interactive ground control problems were categorized into four areas. These are pillar load transfer, massive interseam shearing, subsidence and pressure arching effects. To facilitate research, each of these areas was studied separately although in reality these subdivisions are arbitrary and have considerable overlap.

Jan 1, 1983

By J. H. Field

Synthesis of hydrocarbons by the Fischer-Tropsch reaction in a hot-gas- recycle system was demonstrated to be technically feasible. This project was undertaken, by the Bureau of Mines, to determine if the system was operable and to ascertain the optimum conditions for the production of gasoline. Carbon steel turnings packed with a void volume from 88 to 90 pct. were satisfactory catalysts, but steel catalysts with greater void volume, either turnings or steel wool, were not as active. Good temperature control with a pressure drop of less than 0.5 pounds per square inch (p.s,i,) per foot of catalyst bed of turnings was obtained by operating with a recycle to fresh feed ratio of 20 and by splitting the total gas flaw and injecting portions into the reactor at different entry ports.

Jan 1, 1961

By Nils A. Eilertsen

This Bureau of Mines report describes the unit cost procedure for estimating direct development costs within a cave block in an undercut block caving mine. Costs of supervision, labor, equipment, and supplies are combined to build a unit cost for each type and size of mine development opening in the block. These costs are then combined to estimate the direct cost for developing a ton of ore. Operating data from several domestic metal mines are combined with a hypothetical mining system to illustrate the costing procedure.

Jan 1, 1975

By J. P. Morris

"INTRODUCTION In the investigation being conducted by the Bureau of Mines concerning the production and utilization of sponge iron, it soon became evident that more information was needed regarding methods for determining the degree of reduction attained in the manufacturing process. Sponge irons made by different processes vary in physical characteristics and chemical composition, and a method of analysis that is suitable for one type is not necessarily applicable to all others. For example, the hydrogen-evolution method, which measures the volume of hydrogen evolved upon treating the sample with acid, accurately determines the oxygen content of some types of sponge iron. However, when the sponge iron contains combined carbon, hydrocarbon gases are also-evolved and large errors may result. Probably no single method will give accurate results in all instances, and for this reason it is desirable to have several reliable procedures available and to know the limitations of each.For measuring the degree of reduction, determination of either metallic iron or oxygen should suffice, although for practical application of sponge iron to the production of steel the oxygen content is more significant. After consideration of proposed methods of analysis in regard to their suitability for routine use and the probable influence of other substances, four procedures were chosen for investigation:(1) Mercuric chloride method.(2) Copper sulfate method.(3) Hydrogen-reduction method.(4) Hydrogen-evolution methods."

Sep 1, 1945

By Homer J. Ballinger

The Alma, Degraff and other mines controlled by the Mon-Ark Mining Co. comprise one of the more important groups of zinc-lead mines in Christian County, Mo. The mines were first operated in .1857 and produced more than 5 million pounds of lead from rich, shallow ore deposits. Recent exploration and development led to the discovery of zinc sulfide ore at a depth of 165 to 214 feet in the northern part of the Alma mine. After examination of these mines in September 1942 by Bureau of Mines engineers, investigation of the extension -of the Alma mine and of the depth of mineralization at the other mines appeared justified in order to encourage the production of additional zinc and lead for war purposes. Twenty-nine churn-drill holes totaling 6.463 feet of bore were completed by the. Bureau from September 1943 to January 1944.

Jan 1, 1948

By J. J. S. Sebastian

The process development described in this report was carried out at the Morgantown Station of the U. S. Bureau of Mines in cooperation with West Virginia University. An experimental laboratory-scale pilot unit to gasify coal dust in entrainment was constructed on the Campus of the University in Morgantown. The enormously accelerated demand for liquid and gaseous fuels and utilization of our immense coal resources require that a low-cost process be developed for the gasification of a wide variety of coals. Such a process would be a major factor in lowering the cost of synthetic liquid fuels. None of the proc3sses developed in Germany prior to and during World War II, such as the Winkler process, the H. Koppers dust gasification process, the Wintershall-Schmalfoldt process, etc., meet all the requirements for a low-cost process under American conditions. Nor has any other process designed and experimentally operated at atmospheric pressure during the post-war period in this country appeared to fulfill all of the necessary conditions for a low-cost process.

Jan 1, 1950

By Grant R. Brown

The report provides guidance for determining those environmental impacts associated with the surface mining of steeply pitching coal seams. In addition to the environmental impacts, four additional issues are addressed, namely (1) Time and motion studies of those coal mining systems employed in mining seams which pitch in excess of 250, (2) Assessment of those mining techniques, (3) Development of rationale for the mining methods employed, (4) Identification of the reclamation practices and determine whether these practices were in compliance with appropriate Federal and State regulations. Five surface mines located in three geologically distinct basins of the United States were analyzed during the period of August through November 1979. The three basins include the Hanna Basin of Wyoming, the North Park Basin of Colorado and the Southern Anthracite Field of Pennsylvania.

Jan 1, 1980

By Kim B. Shedd

The Bureau of Mines measured fiber dimensions on crocidolites (riebeckite-asbestos and magnesioriebeckite-asbestos) from the world's four crocidolite mining regions. The objective of the study was to determine whether there are measurable morphological differences between crocidolite fibers that correlate with the high reported incidence of mesothelioma in miners and mill employees in the Cape Province of South Africa and Western Australia, as compared with little or no reported incidence of this cancer in the Transvaal Province of South Africa or Bolivia. Fiber dimensions measured with the scanning transmission elec-tron microscope showed that crocidolites from Western Australia and the Cape Province have more thin fibers than crocidolites from Bolivia and the Transvaal Province.

Jan 1, 1985

By Michael Rieber

The increase in f.o.b. mine prices of coal from $5/ton to over $18/ton in five years [1] has increased the significance of transportation costs. Coals produced in the vicinity of the consumer bear a much lower transport cost than those produced in the west. This differential may be used for flue gas desulfurization, other cleaning, or further processing of local coals. To the extent that western coals are cheaper to produce and have a lower sulfur content, they offset the locational disadvantage. To the extent that they have a lower heating value, the disadvantage is exercabated. Given the other conditions, an accurate analysis of transport costs will help suggest the location of coal mining and the moue of transport both transport costs and tariffs have risen. Together they have increased delivered coal prices, altered the balance between the use of coal and other fuels, helped to alter the location of mining activity, and put pressure on consumers to examine the cost effectiveness of alternative transport modes. Transportation options for long distance coal movements include rail, barge, pipeline, and EHV transmission lines. A summary of system parameters is shown in Table 2.1. Barge transport, pneumatic and slurry pipelines are discussed elsewhere in this report. Together with EHV, they have been the subject of previous studies [2,3,4]. Slurry pipelines have been shown to be especially useful where rails are not available [2] but the technical problems of dewatering, handling, and utilization of lines [5] remain unresolved. They are discussed in Section 3. Barge transportation depends on the location of the mine and consumer with respect to the waterway system. One drawback of barge shipment is interruptions due to winter, and low or high water conditions. Mine mouth power generation followed by EHV transmission of over 500 miles has been shown to be the most expensive means of delivering an equivalent amount of energy to consumers [2].

Jan 1, 1977

By R. J. Campbell

[The steady increase of aluminum production means a corresponding increase of carbon consumption in the alumina-reduction cells. Improved petroleum techniques constantly reduce the amount of byproduct petroleum-coke production. These, trends threaten the alumina-reduction works with possible shortages of carbon, which must be supplied from some other source. In anticipation of this shortages, an investigation into the possibility of using coal as an alternative source of carbon was begun at the Northwest Experiment Station of the Federal Bureau of Mines. The investigation lit has developed bench-scale methods that produce carbon of higher purity than is required by specifications for anode carbon. Additional work will b required to bring these processes to pilot-plant seals and to prove the suitability of the carbons, produced or aluminum-anode consumption.]

Jan 1, 1956

By Lance R. Barron

Over the past decade, the U.S. Bureau of Mines (USBM) has studied longwall gate road stability at four mines in the Book Cliffs and Wasatch Plateau Coalfields of Utah. These operations are characterized by multiple-seam mining, abruptly varying cover depths to 914 m (3;000 ft), and massive rigid, sandstone units in the main roof or floor. Such conditions encourage severe bumping, roof instability, and occasional floor heave problems.' Various gate road configurations have been employed to alleviate' these problems. Although the mines have comparable basic conditions, the lithologies and qualities of the immediate roof, floor; and seam ate different in each mine and often vary in a single mine. Gate road systems that mitigate hazards in one mine may prove inappropriate in another or for different areas of the same mine. This report relates the geology of the coalfields; describes the location, geologic setting, specific mining conditions, operating history, and the USBM field study and results or conclusions for each mine; summarizes the relative performance of the gate road systems; and emphasizes the need for site-specific geotechnical data to evaluate gate road conditions and performance.

Jan 1, 1994