Search Documents

By J. E. Zeilinger

This Bureau of Mines report describes the preparation characteristics of the significant coalbeds of Beaver and Lawrence Counties, Pa. Washability analyses were made on seven coalbed samples, none of which were of metallurgical quality as received. Five of the samples could be sufficiently upgraded to produce acceptable products, and the remaining two samples could not be upgraded to metallurgical quality because their sulfur contents could not be lowered to meet the standard. For steam or power generation, one sample was of low sulfur content as received, one sample could be upgraded to low sulfur content, and three samples could be upgraded to medium sulfur content. The original sulfur content of the remaining two samples can be appreciably reduced by removal of the sink 1.58 speci fic gravity material; however, these coals would be classified as medium sulfur coals both before and after removal of the sink material.

Jan 1, 1969

By J. E. Chilton

The U.S. Bureau of Mines has developed an intrinsically safe carbon monoxide (CO) monitoring system for mines by coupling a fiber-optic data telemetry (FODT) system with a prototype electro-chemical CO monitor. The CO monitoring system can be used in a coal mine as one component of an early fire warning system. This system may be used in belt haulage entries when the entries are used for supplying ventilation air to working places. The FODT accepts a 0.1-to 1.1-V analog signal from the monitor and converts it to pulses (0 to 5 V) at frequencies from 1.1 to 11 kHz that drive a light-emitting diode (LED). An electrically nonconducting fiber-optic cable carries the LED signal to a remote receiver. The receiver analyzes the incoming light signal and displays the measured CO concentration in parts per million. This report discusses the performance of the FODT system and characteristics of the CO monitor such as response times, linearity, and temperature and pressure effects.

Jan 1, 2010

This report is the 23d in a series summarizing research and technologic work by the Federal Bureau of Mines on coal and related investigations; it is the fifth report to be issued on a calendar-year basis.2/ Publications by Bureau personnel in 1958 are cited;3/ in addition work in progress during the year is briefly described. To conserve our reserves of coal the Bureau of Mines conducts a program concerned with the development of fundamental information on coal characteristics and behavior, and the improvement of technology related to its production and utilization. The ability to anticipate and meet future demands for coal depends on a number of factors: (1) Knowledge of reserves from a stand- point of both quantity and quality; (2) the development of improved mining methods, health and safety measures, and preparation techniques that will insure its most efficient exploitation; and (3) knowledge of the controlling factors in efficient use of coal in combustion, carbonization, gasification, direct and indirect hydrogenation, and other new processes. The Bureau is concerned with each of these areas.4/,5/

Jan 1, 1960

By E. R. Palowitch

A centrifugal float-and-sink test procedure has been developed by the Bureau of Mines to reduce the time for the gravimetric separation of coals finer than l4-mesh from as long as 24 hours to less than 1 hour. Comparative tests indicated that centrifuging a minus 14-mesh Pittsburgh-bed coal for 20 minutes at 1,500 revolutions per minute produced results that compared favorably with static float-and-sink test results. Standard deviations of the mean recovery and ash content of the float obtained centrifugally ranged from 1.31 and 0.04 percent, respectively, at 1.30 specific gravity to 0.21 and 0.05 percent, respectively, at 1.60 specific gravity. As in static separations, retreatment of the products separated at low specific gravities was required.

Jan 1, 1961

By R. C. Buehl

Pilot-plant tests have been in progress at the Bureau of Mines, Pittsburgh, Pa., on the recovery of manganese from open-hearth slag.3/4/5/ In the process, 1 the slag is first reduced in a blast furnace to make a high-phosphorus spiegeleisen containing 12 to 22 percent manganese. A slag containing 55 to 60 percent manganese is made from this spiegel by oxidation in a basic-lined converter. The metal from this blowing operation contains about 3 percent phosphorus, 1 percent manganese, and less than 1 percent carbon. Economic efficiency in the manganese-recovery process requires that this metal be converted into steel. Because of its high phosphorus content the metal is suitable for blowing in a basic-lined converter. In most of the tests described in this report, metal of this composition was used as the starting material in a 1-ton, side-blown, basic-lined converter. Although basic-lined converters are not used for steel production in the United states, in Europe a considerable portion of the steel is made in them. Open hearths largely have replaced converters for steelmaking in the United States; mainly because open-hearth steels have better physical properties than converter steels because of lower nitrogen and phosphorus contents. However, by improving converter design and operating technique during the past 15 years, metallurgists have found that low-nitrogen steels with physical properties equal to open-hearth steels can be produced in converters.6/ Tests at Jones & Laughlin steel Corp. with side-blown, acid-lined converters of 3 and 22 tons capacity showed that steel with a low nitrogen content comparable to that of open hearths operating on scrap charges could be made by surface blowing.7/

Jan 1, 1955

By P. L. Woolf, J. P. Morris, E. Foerster, G. R. Zellars

Measurements of vapor pressure can be used to determine the thermodynamic activities of the components of metallic solutions . The determination of activity by this method requires accurate values for the vapor pressure of the pure component and for its partial pressure above the alloy solution . This investigation was conducted to measure the vapor pressure of liquid manganese for use in future studies of the activity of manganese in various liquid alloys . In related investigations in the Bureau's Pyrometallurgy Laboratory , vapor pressures of copper , iron and nickel have been measured and activit 4 5 6 have been determined in the iron- copper and iron- nickel systems . Difficulties were experienced with manganese which were not encountered in the previous investigations . Manganese oxidizes readily and greater care was needed to maintain an oxygen- and moisture - free atmosphere in the furnace . In addition , liquid manganese wet the refractories and there was a tendency to foam and splash on introduction of the carrier gas . Because of these difficulties several variations in the experimental procedure were studied . These were first tested with silver which has a vapor pressure of the same order of magnitude as manganese but is relatively inert at high temperatures . Although no significant changes in the original procedure resulted from this work, considerable data were obtained for silver and have been included in this report . Bauer and BBrruunnnneerr7/ have reported the only extensive investigation of the vapor pressure of liquid manganese . However , their results are not consistent with the data obtained by McCabe and Hudson for solid manganese . Measurements of the vapor pressure of silver have been reported by McCabe and Birchenal1,2/ Schadel and Birchenall , 10/ Harteck , 11 / Fischer , 12/ and von Wartenberg.13 / Generally , these investigators conducted their measurements at lower temperatures than were used in this study .

Jul 1, 1960

By George A. Morgan

The production and processing of crude petroleum and natural gas are the dominant economic sectors of the Middle East. Downstream processing of these mineral fuels to petrochemicals and fertilizers is a major investment opportunity. In 1991, the 15 countries that constituted the region accounted for 26 % of world crude petroleum output, 15.3 % of world natural gas plant liquid production, and 4.5 % of world dry natural gas production. Only Cyprus and Lebanon were not crude petroleum producers. Production of these mineral fuels all declined from that of 1990 owing to the Persian Gulf War, during which output from Kuwait and Iraq either ceased owing to war damage, or was embargoed. Prior to the war, Iraq and Kuwait were the fourth and fifth largest world producers of crude petroleum, respectively. In the war, virtually all of Kuwait's production and transport facilities were destroyed or damaged. Iraq's output was embargoed from export, with only domestic sales taking place. The embargo also affected Jordan, both in terms of transshipment of materials through it to Iraq and in exports of phosphate and potash. Shipments of crude petroleum by pipeline from Iraq through Saudi Arabia and Turkey and by vessel through the Persian Gulf were terminated. However, the loss in production from Iraq and Kuwait was made up by accelerated output from other Middle East and world producers. Saudi Arabia, in particular, with its excess production capacity, accounted for the largest portion, increasing crude petroleum output by 27 % to almost 3 billion barrels.

Jan 1, 1993

By M. S. Seehra, V. S. Babu, L. Farinash

"The diesel particulate matter (DPM), a constituent of the diesel engine exhausts, is known to be a potential carcinogen. 1- 3 Consequently, suitable methods to control/eliminate DPM have ·been under investigation in recent years. The DPM can be controlled by using fibrous ceramic traps. However, clogging of traps by DPM requires the impractical periodic trap replacement. Following the recent work by Garner and Dent,4,5 we are investigating the in situ use of microwaves to regenerate the ceramic traps, thereby eliminating the trap replacement step in this process. The use of microwaves instead of conventional heating for trap regeneration has the advantage of selective heating of the DPM instead of the trap, if the trap absorbs insignificant microwave power relative to the DPM. Also, the oxidation characteristics of the DPM are needed to understand fully this regeneration process.The rate of energy absorption P per unit volume of a sample is given byP = wE"" |Eo|2 • (1 )where w is the angular frequency, |E0|2 is the intensity of the microwave radiation, and E” is the imaginary part of the dielectric constant (E = E’ + iE”) . Thus measurements of E11 for DPM and ceramic trap material are needed to determine their capacities for microwave absorption. In this paper, we report these measurements carried out at · a frequency of 8.7 GHz. Following microwave absorption, the DPM is expected to oxidize. The oxidation characteristics of the DPM have been investigated using Fourier transform infrared (FTIR) spectroscopy of the evolved gases CO2 and CO and using thermogravimetric analysis (TGA). Finally, some information on the structure of carbon in DPM has emerged from the analysis of its x-ray diffraction spectra. Results of these experiments are reported in the following pages."

Dec 1, 1996

By W. A. Calhoun

The purpose of this investigation was to develop a procedure for removing excess iron from representative samples of bauxite ore from the Quapaw deposit of American Cyanamid Co., Saline County, Ark., in order to produce a beneficiated ore suitable for use in the alum industry, At the request of the sponsoring company, the samples were reduction-roasted at 800° C. and then magnetically separated. Although some rejection of iron was effected under these conditions, the general results were not satisfactory, A much more successful procedure, from the standpoints of both rejection of iron and recovery of alumina, consisted of a short (l5-minute), low-temperature (400° C.) oxidizing roast, followed by a 2-minute interval in a hydrogen atmosphere, then cooling to room temperature, and, finally, high-intensity magnetic separation to remove the iron.

Jan 1, 1957

By S. P. Sandoval

The U.S. Bureau of Mines investigated the separation of aluminum from copper dump leaching liquors using a supported liquid membrane. Aluminum was selectively transported through porous polypropylene impregnated with di (2-ethylhexyl) phosphoric acid in an aliphatic diluent. The effects of variables, such as solution composition, temperature, and extractant concentration, were measured with a three-level fractional factorial experimental design. Experimental results were used to derive equations for predicting transport rates for aluminum, iron, and copper. The major variables influencing aluminum transport were solution temperature, feed solution pH, aluminum concentration in the feed solution, and extractant concentration. Copper and iron transport rates were almost zero when aluminum transport rates were high. Measured aluminum transport rates under the best conditions of 55° C, pH 3.0, 16 g/L A13+, and 65 pct extractant solution confIrmed the predicted value of 210 f.'g/(cm2.h). Transport rates for iron and copper were less than 5 ug/(cm2.h) under these conditions. Aluminum was recovered from the stripping solutions by sparging with gaseous hydrogen chloride to crystallize aluminum chloride hexahydrate, which was calcined to alumina. Sparging crystallization regenerated the stripping acid for recycle.

Jan 1, 1989

By L. B. Pankratz

The heat content above 298.15° K was determined for crystalline vanadium silicide of the composition V3Si. This substance has a minor thermal anomaly (probably a heat-capacity maximum) near 560° K; the extra heat absorption is about 50 cal/mole. The original heat-content data are presented, and smooth values of the heat content and the corresponding entropy increments are listed for the temperature range from 298.15° to 1,500° K. Equations representing the heat- content values and derived heat capacities are also included.

Jan 1, 1963

"MASSACHUSE'M'S INSTITUTE OF TECHNOLOGYBOLSAITIS, PETERMassachusetts Institute of TechnologyDepartment of Mineral Engineering77 Massachusetts AvenueCambr1dge,MA 02130(614) 253-5069ELLIOIT, JOHN F.Massachusetts Institute of TechnologyDepartment of Mineral Engineering77 Massachusetts AvenueCambridge, MA 02130(617) 253-3305RING, TERRYDepartment of Materials Science and EngineeringMassachu5etts Institute of TechnologyCambridge, MA 02130(6117) 253-4299"

Jan 1, 1988

By S. H. Brooks

"IntroductionThis preliminary report deals with the effect of oxygen pressure on the ignition temperature and combustibility of oils, it is the third of a series which will present the results of an investigation being made by the Bureau of Mines, on oxygen-oil explosions. The purpose of this research is to obtain technical data that will serve as a basis for safety precautions general outline of the problem has been given in the first report (Serial 2507).The present experiments have resulted in (1) a method for determining spontaneous ignition points of oils in an atmospheric of oxygen under pressure; and (2) the determination of these ignition temperatures for three typical oils, one being an animal oil (sperm), one a vegetable oil (linseed), and one a mineral oil (""Moiloil A"").These experiments on explosibility of oil were performed in order to discover the general nature of the phenomenon, especially the order of magnitude of the temperature necessary for spontaneous explosion (120°C. and upwards) and the effect of pressure variation (negligible as regards ignition temperature but important in relation to the violence of the explosion). A continuation oftests should provide a basis for selecting the safest lubricants for high pressure compression of gases particularly air and oxygen; and should be of value when devising new specifications for lubricants, both in the government departments and the compressed-gas manufacturing industry."

Dec 1, 1923

By Jeffrey M. Listak

The Respiratory Hazards Control Branch of NIOSH routinely conducts laboratory and mine-site evaluations of dust control technologies. Gravimetric and instantaneous dust sampling instruments are used in these evaluations to measure and document dust levels to determine worker exposure. The Thermo personal DataRam (pDR) is an instantaneous sampler that uses light-scattering technology to provide relative measures of airborne respirable dust. The pDR can be used in active and passive modes to measure respirable dust levels. Tests were conducted to evaluate the sampling performance of active and passive pDR operation relative to each other and. against a gravimetric sampler (the accepted standard for respirable dust measurement). The purpose of the test was to determine if the pDR can be used effectively in the passive mode in higher velocity airflows (up to 5.1 m/s (1000 fpm)). Studies of the pDRs in both modes of operation were conducted in a controlled laboratory environment and in field situations. Dust measurements using pDR units in both modes of operation were recorded in ve¬locities ranging from 1.0 to 5.1 m/s (200 to 1000 fpm). Tests were conducted in ambi¬ent air and in air with the addition of moisture. Results show that, although the units measure different concentrations in their respective modes of operation as compared to a gravimetric sample, the relative readings can be corrected to yield accurate dust measurements.

Jan 1, 2007

By M. O. Magnuson

This publication describes abandoned-mine fire-control work administered by the Bureau of Mines under cooperative agreements with State and local governments. The work was done by private contractors under the supervision of Bureau engineers. The work is authorized by Public Law 738, approved August 31, 1954, and Public Law 89-4, approved March 9, 1965. Earlier work was authorized by Interior Department Appropriations Acts for fiscal years 1949-55. A total of 70 fires have been controlled under this program in the eastern bituminous region. The nature and extent of the abandoned-mine fire problem in the bituminous region is discussed, and the methods used for controlling these fires are described. The methods that have been used, either singly or in combination, include loading out and cooling the burning material, installing fire barriers, surface sealing, and water and pneumatic flushing.

Jan 1, 1974

By E. D. Gardner

"Introduction Ore from stopes in metal mines is generally dumped or drawn into chutes or raises through which it passes by gravity to the haulage levels. Occasionally, and under some conditions quite frequently, the ore in a chute will wedge or hang and refuse to run. This hanging of the ore may be due to the packing of damp or clayey material, to boulders forming an arch, or to loose lagging or other timber becoming lodged in the chute.In drawing material from a loading chute it is drawn out a car at a time, and the intermittent flow of the material .increases its tendency to hang. When the obstruction in the chute is near or at the loading gate, the chute pullers start the ore by punching it with iron bars inserted through openings in the chute gate. When the obstruction is beyond reach of the bars, other means of starting the ore must be used.In some systems of mining, chutes or ore raises are built with timber as the stope extends upward. Generally, a manway is left alongside of the chutes, and when the ore hangs in a chute usually it can be started by a miner from the manway ladder by pounding on the timbers of the chute or by punching the ore with a bar inserted through small holes in the chute lining. Special methods of starting clogged ore, such as shaking a chain left hanging in the chute, are used at some places.In other systems of mining, ore passes or chutes are run through solid rock and when the ore hangs in one of these passes, either it must be blasted or else started from the top. Sometimes the ore can be started by running water into the top of the chute, but if the water does not start the ore moving, it must be blasted from underneath. This is done by detonating a bundle of cartridges under the obstruction in the chute or raise."

Jan 1, 1927

By Rose L. Ballard

This chapter summarizes data on crude nonfuel mineral production for the United States, its island possessions, and the Commonwealth of Puerto Rico. Included also are tables that show the principal nonfuel mineral commodities exported from and imported into the United States, and that compare world and U.S. mineral production. The detailed data from which these tables were derived are contained in the individual commodity chapters of volume I and in the State chapters of volume II of this edition of the Minerals Yearbook. Although crude mineral production may be measured at any of several stages of extraction and processing, the stage of measurement used in this chapter is what is normally termed "mine output." It usually refers to minerals or ores in the form in which they are first extracted from the ground, but customarily includes the output from auxiliary processing at or near the mines. Because of inadequacies in the statistics available, some series deviate from the foregoing definition. For gold, silver, copper, lead, zinc, and tin, the quantities are recorded on a mine basis (as the recoverable content of ore sold or treated). However, the values assigned to these quantities are based on the average selling price of refined metal, not the mine value. Mercury is measured as recovered metal and valued at the average New York price for the metal.

Jan 1, 1981

By G. L. Oldright

This paper is the first of a series that is to appear on smelting in the lead blast furnace. The objects of this investigation are to determine the conditions obtaining within the blast furnace by direct experimentation, and to correlate the behavior of the furnace at various times with the main factors governing the operation of the blast furnace, and metallurgical losses. ACKNOWLEDGMENTS The writers wish to express their appreciation to the management of the International Smelting Co. at Tooele, Utah, to Mr. J. O. Elton, the general manager, and to Mr. A. B. Young, his assistant, for their broad-gauge policy that has made possible the securing and publishing of these data. For the staff at Tooele, acknowledgments are made to Messrs. B. L. Sackett, general superintendent, Carlos Bardwell, assistant general superintendent, S. Jacobsen, blast-furnace superintendent, H. M. Rockwell, assistant blast furnace superintendent, and J. O. Welsh, superintendent of the general research, for the spirit of cooperation they manifested in carrying out this work. Mr. C. Reish, a member of the research department, was detailed by, the company to assist in this' work and his whole-hearted assistance has been found invaluable.

Jan 1, 1929

By Arthur J. Hudson, Lawrence W. Scott

The performance of RETIMET metal foam as a flame arrester on explosion-proof enclosures was investigated by the U.S. Bureau of Mines both in laboratory tests and at the U.S. Mine Safety and Health Administration's (MSHA's) Approval and Certification Center, Triadelphia, WV. The objective of this research was to develop a permissible pressure vent for use on lightweight, vented, explosion- proof enclosures. In laboratory tests, four grades of RETIMET, a stainless steel foam material, were evaluated: (1) 45 NC-7, (2) 45 NC-13, (3) 80 NC-7, and (4) 80 NC-13. Explosive gas mixtures were prepared by a dynamic flow system. Ignition was by a low-voltage arc. Each grade of RETIMET metal foam successfully arrested the flame front in all methane-air tests. To evaluate RETIMET metal foam on large, commercial size enclosures, a multicompartmented enclosure was designed and tested in MSHA's explosion gallery in Triadelphia, WV. Extensive explosion testing revealed that a minimum vent-area-to-enclosure-volume ratio of 11.33 in2/ft3 is required to keep internal pressure rises below 3 psig. The RETIMET metal foam functioned satisfactorily in all tests as evidenced by the absence of external ignitions.

Jan 1, 1992

By D. Harrington

We Americans pride ourselves that ours is the greatest, most advanced and most civilized nation in the world, yet statistics indicate that apparently we have little appreciation for the lives and limbs of the people whose efforts give us whatever greatness we possess. The latest available statistics indicate that the annual accident death rate per 100,000 of population is nearly 80 or far higher than that of any other country in the world except Chile; is more than double the rate in Hungary, Netherlands, Ireland, Belgium, Denmark, Italy, Germany, Norway, Sweden, and Finland; is nearly double that of England, Wales, the Union of South Africa, New Zealand, Japan, Australia, and Scotland; and is 25 to 40 percent greater than Switzerland, France and Canada. To make matters worse, from the viewpoint of mining; the latest available statistics give mining by all adds the worst accident rate of the major industrial occupations in the United States, the accident severity rate for mining in 1935 being listed by the National Safety Council as 10.14, the next highest rate being 4.52 for construction, and the average rate for 30 main industries being 1.58. IMPROVEMENT IN SAFETY RECORDS Offsetting to a slight extent this rather dark picture is the fact that starting about 1930 the mine-accident rate in both coal and metal mining began to fall, reaching an all-time "low" in metal mining in 1932 and in coal mining in 1933. It now appears probable that the year 1936 has again lowered the accident rate in coal mining and this, together with the fact that the years 1933, 1934, 193 5, and 1936 all set much lover accident rates in coal mining than ware achieved for any similar previous period, gives hope that the trend is definitely in the right direction, though from the above figures mine-accident severity has a long, tedious road to travel before it becomes as low as the severity rate of all other major industries in the United States.

Jan 1, 1937