Search Documents

By Linda L. Chasko, Larry D. Stowinsky, Ronald S. Conti

Mine operators often rely on mine rescue teams to save lives during an underground emergency such as an underground fire, explosion or roof fall. It is extremely important that team members are provided with adequate exploration equipment and that training simulations are conducted in a realistic manner. A series of mine rescue training exercises was developed, conducted and evaluated by the National Institute for Occupational Safety and Health (NIOSH) in cooperation with the Pennsylvania Department of Environmental Protection, Bureau of Deep Mine Safety. The exercises were conducted at NIOSH’s Lake Lynn Laboratory during 1995 to 1998 and resulted in improved technology and training for mine rescue teams. For example, existing technologies were identified to help rescue teams during exploration. These included chemical light sticks to identify team members and mark crosscuts and mine materials, strobe lights for mapping out escape ways, and a helmet mounted thermal imaging system to see through smoke. A hands-free communication system showed potential for enhanced communications between team members and the fresh air base. A new high-visibility team lifeline that allows for flexibility of movement between team members was developed. A positive-pressure inflatable escape device (IED) was used to isolate the “hazardous” environment from fresh air and allow rescue team members to traverse through. An inflatable feed-tube partition that can rapidly block large openings such as underground passageways and simultaneously provide a feed-tube for high-expansion foam generators was also deployed for several simulations. During the simulations, mine rescue team members donned self-contained breathing apparatuses (SCBA) and traversed more than 305-m of mine passageways filled with nontoxic smoke. Visibility ranged from 0.3 to 0.9-m. In one area of the mine, a kerosene heater was used to simulate a fire and reduce the oxygen concentration. In another area, a 1.5 pct methane zone was established. The team members searched for "victims,” mapped the passageways, built temporary stoppings and ventilated the smoke-filled entries. The teams indicated that the simulations were challenging and very informative.

By William C. Cooley

[Data from t.-raturs on each hydr,ne has been assembled on the- data sheets whichw6ed in this Appandin. Dai_iis are provl_ od for ::amines or hydraulic s-ctions in the USSR (TDPhw~s), 8 in ASR (Kuzbass) , 1i-gin i, 1 in 7in China, i in Japan, and l in C~n- i.Ata sheetsiov tion prepared for mines in New Zealah_~sddered very rele¬ vant, nor forf !aA of information. In aW,!~.F in : --- C=SR for tiara ShoeLS ara 1palAwdl satinieral mines have operac- ~ - re Manned about which very limited data exist as folloos:]

Jan 1, 1975

By Maurice J. Peterson

THE VISUAL-ARC spectroscopic method of rapid qualitative analysis of complex inorganic compounds has been popularized in the past few years and is being employed by an increasing number of laboratories. The mineralogy and chemistry departments of several universities recently have added visual spectroscopy to their laboratory curricula. This revival of interest in a somewhat dormant analytical method has been stimulated through the publication of three papers 4 by members of the College Park staff of the Bureau of Mines. These virtually are the only recent sources of information on visual-arc spectroscopic analysis. They include data on the spectroscopic assembly, the analytical procedure, and the practical application of the method to determinative mineralogy and related fields. Requests for reprints of these papers continue to be received; at present only a limited number of copies are available for distribution. In order that these requests may be adequately answered, material from the three papers has been combined and, with some additional data, is presented in this bulletin. Numerous specific inquiries have been received regarding types of equipment available, problems in instrumentation, and information on the approximate sensitivity limits of the elements that can be detected by this method. Some of this material was not included in the original papers. Accordingly, the table of wavelengths has been revised to include the approximate visual-arc spectroscopic sensitivities, and a section on commercially available equipment has been added.

Jan 1, 1953

By R. G. Travis

1. Reserve estimates have been made for eight coal beds in Monongalia County, W. Va., but only the Pittsburgh, Sewickley, and Upper Freeport beds are important at this time. The Pittsburgh, Sewickley, Waynesburg, and Upper Freeport beds contain the largest recoverable reserves. 2. Known measured and indicated reserves in all beds, based on a minimum thickness of 14 inches and 1,800 short tons per acre-foot of coal in place, are estimated at 3,526 million tons as of January 1, 1954. Of this total, 3,294 mil-lion tons is in beds 28 inches and more thick. Areas in each bed except the Pittsburgh were omitted from the estimate because available data relative to the bed characteristics are too meager for making an estimate that conforms with the definitions of measured and indicated coal adopted for this study. Should future drilling or development prove reserves in these areas, such reserves should be added to the total estimated reserves.

Jan 1, 1956

By S. C. Rhoads

The Bureau of Mines is investigating low-chromium alloy substitutes for type 304 stainless steel (type 304 SS). The purpose of the research is to reduce the chromium content in austenitic stainless steels used for corrosion-resistant applications. Nine Fe-9Cr-12Ni alloys containing additions of 0 to 5 pct Mo, 0 to 2 pct V, and 0 to 2 pct Cu were selected for evaluation. All of the experimental alloys containing 5 pct Mo and an alloy containing 2Mo-2V-2Cu possessed structure and tensile strengths similar to those of type 304 SSe Alloys containing SMo-2V and SMo-2V-2Cu had ac-ceptable welding properties as measured by the Varestraint test. Alloys containing at least 2 pct Mo had cQrrosion resistance comparable to that of type 304 SS in solutions of nitric acid, phosphoric acid, acetic acid, and citric acid. In chlorides, all the experimental alloys were susceptible to localized corrosion and stress corrosion cracking similar to that of type 304 SSe The corrosion properties were established by weight-loss tests, electrochemical polarization tests, and stress-corrosion cracking tests. An Fe-9Cr-12Ni-SMo-2V alloy and an Fe-9Cr-12Ni-SMo-2V-2Cu alloy had a combination of welding properties, tensile properties, and corrosion resistances that were most comparable to those of 304 SS.

Jan 1, 1984

By Larry Patts, Jon Hummer, Jim Noll, Aleksandar Bugarski1, George Schnakenberg, Steve Mischler, Mike Crum, Shawn Vanderslice, Rick Anderson

This study is organized under the auspices of the Metal/Nonmetal Diesel Partnership formed by the National Institute of Occupational Safety and Health (NIOSH), the National Mining Association (NMA), the National Stone Sand and Gravel Association (NSSGA), the United Steel Workers of America (USWA) and the MARG Diesel Coalition. The ultimate objective of the study is to reduce the exposure of underground miners to diesel particulate matter (DPM) and gases, and to help in fulfilling the partnership’s goal of identifying technically and economically feasible controls to curtail particulate matter emissions from existing and new diesel powered vehicles in underground metal and nonmetal mines. The majority of current knowledge on the performance of the diesel particulate filter (DPF) systems and other control technologies is based on studies done under laboratory conditions, the results then being applied the results to on-highway vehicles. According to the best knowledge of the authors, only two comprehensive studies that were conducted recently at Noranda’s Bathurst Mining and Smelting Mine and International Nickel Company’s Stobie Mine under the sponsorship of the Diesel Emissions Evaluation Program [McGinn 2001, Bugarski and Schnakenberg 2001, Bugarski and Schnakenberg 2002] offered some insight into the problems associated with the deployment of modern DPFs to underground mining vehicles. The U.S. mining industry has expressed concern that this rather limited knowledge base is not sufficient to help them comply with the rule limiting DPM exposure of underground metal and nonmetal miners [30 CFR 57.5060 2001]. The partnership agreed that a series of comprehensive field evaluations of DPFs in several underground mines was needed to determine their viability of DPF systems and establish confidence in their performance. The first in this series of studies was the one conducted in Stillwater Mining Company’s Nye Mine, Nye, Montana. This study was conducted in two phases. The objective of the first phase was to establish the effectiveness of the selected technologies in reducing diesel emissions by using an isolated zone methodology. The objective of the second phase was to assess the effectiveness of diesel particulate filters in controlling the exposure of underground miners in actual production scenarios. As part of the first phase of the study a series of tests were conducted at Nye Mine from May 19, 2003 until May 30, 2003. The results of Phase I of the study are presented in this report.

Jan 1, 2005

By D. C. Seidel

This report describes generic procedures and equipment arrangements for conducting laboratory-scale hydrometallurgical and related waste-management experiments. It provides a starting point for personnel who have received or are receiving professional training, but do not have specific experience in laboratory procedures. With guidance, it also has application as a resource for technician training. The publication contains chapters on laboratory safety, feed-sample preparation, leaching, solids-liquid separation, and recovery from solution.

Jan 1, 1995

By Michael J. Klishis

West Virginia University researchers examined risk and exposure in the roof bolter operator's job and developed approaches for preventing accidents and for evaluating system and human performances that may be appropriate as a general application to improve safety and efficiency in the industry. Using a microanalysis of accident data and underground observations, the researchers classified bolting injuries within one of four work routines: 1) drilling bolt holes; 2) bolt installation; 3) machine tramming, (re)positioning and setting the ATRS; and 4) general face preparation. Time and motion studies were then combined with injury data analysis to develop risk and severity indices, as well as a severity-weighted index that served to determine the degree of risk and exposure by work routine. More than two dozen bolting-related problems were identified as potential situations that could lead to injuries or expose workers during their job. Approaches to avoid these situations were suggested and then applied at six mining operations to evaluate specific problems in roof bolting operations. These suggestions encompassed the three E's of Safety (Engineering, Education, and Enforcement) and emphasized the analysis of worker behaviors that lead to human error accidents.

Jan 1, 1993

By R. C. Ellman

Significant effects of in-the-mill drying on the pulverization of lignite have been demonstrated in an experimental impact-type pulverizer by tests in which the primary variable was temperature of the sweeping gas. Reduced power requirements and increased product fineness were observed as the extent of drying was increased. Pulverization with in-the-mill drying was studied in comparative tests made on lignites from five mine sources. All of the lignites responded in a similar manner; however, differences in the pulverizing characteristics of the individual lignites were significant. For one lignite, the electrical input to the pulverizer driving motor with minimum sweeping-gas temperature was 33.9 kw.-hr. per ton, decreasing to 14.0 kw.-hr. per ton with a sweeping-gas temperature of 658° F.; for another lignite, at comparable operating conditions, the electrical input decreased from 59.1 to 19.0 kw.-hr. per ton. In the first case, the product fineness increased with increasing temperature of sweeping gas from 65.2 to 79.2 percent through a 200-mesh sieve, and in the second case, from b2.7 to 86.9 percent through a 200-mesh sieve.

Jan 1, 1962

By B. R. Mohal, F. F. Aplan, S. Chander

"The wetting behavior of coal has been determined in the presence of nonyl and octyl series of nonionic surfactants containing polyethoxy groups of different sizes. The wetting behavior was determined by a modified Walker technique and contact angle measurements. The results show that the wetting rate of coal varies with coal rank, structure of the hydrocarbon chain and number of ethoxy groups in the hydrophilic group of the surfactant. A close relationship has been observed between the wetting rates and the short-time advancing contact angles.INTRODUCTIONNonionic surfactants are used in many applications to improve wettability of solids. They can be used as dispersing agents [ 1 ] or dust suppressants [ 2-5] and to control the flotation, flocculation, filtration and, flowability of particulates. This study was undertaken to study the effect of a series of nonionic surfactants on the wetting behavior of coal. Two series of surfactants, namely, ethoxylated nonyl and octyl phenols were used. The nonyl phenol series con tains a linear hydrocarbon chain containing nine carbon atoms (CH3 ( CH2 )8-C6H4- ( OC2H4 ) n, where n is the number of ethoxy groups) . The octyl phenol series contains a branched hydrocarbon chain containing eight' carbon atoms ( ( CH3 ) 3CCH2C ( CH3) 2-C6H4- ( OC2H4 ) n ).Initial wetting rates — modified Walker techniqueWalker et al. [ 6 ] developed a sink test to determine the wettability of coal particles. In this technique, coal particles are dropped individually onto the surface of surfactant solutions of different concentrations, and the most dilute concentration in which coal would sink ""instantaneously"" is determine& This technique is a variation of a procedure initially developed by Draves and Clarkson [ 7 ] to determine the effect of surfactants on wettability of cotton fibers."

Jan 1, 1989

By B. R. Mohal, F. F. Aplan, S. Chander

"The wetting behavior of coal has been determined in the presence of nonyl and octyl series of nonionic surfactants containing polyethoxy groups of different sizes. The wetting behavior was determined by a modified Walker technique and contact angle measurements. The results show that the wetting rate of coal varies with coal rank, structure of the hydrocarbon chain and number of ethoxy groups in the hydrophilic group of the surfactant. A close relationship has been observed between the wetting rates and the short-time advancing contact angles.INTRODUCTIONNonionic surfactants are used in many applications to improve wettability of solids. They can be used as dispersing agents [ 1 ] or dust suppressants [ 2-5] and to control the flotation, flocculation, filtration and flowability of particulates. This study was undertaken to study the effect of a series of nonionic surfactants on the wetting behavior of coal. Two series of surfactants, namely, ethoxylated nonyl and octyl phenols were used. The nonyl phenol series contains a linear hydrocarbon chain containing nine carbon atoms ( CH3 ( CH2 ) 8-C6H4-( OC2H4 )""' where n is the number of ethoxy groups). The octyl phenol series contains a branched hydrocarbon chain containing eight carbon atoms ( ( CH3 ) 3CCH2C ( CH3 ) 2-C6H4-( OC2H4)"").Initial wetting rates - modified Walker techniqueWalker et al. [ 6] developed a sink test to determine the wettability of coal particles. In this technique, coal particles are dropped individually onto the surface of surfactant solutions of different concentrations, and the most dilute concentration in which coal would sink ""instantaneously"" is determined. This technique is a variation of a procedure initially developed by Draves and Clarkson [ 7] to determine the effect of surfactants on wettability of cotton fibers."

Jan 1, 1989

By O. P. Hood, R. H. Kudlich

When a gasoline locomotive is used in a mine there is danger of the noxious gases of the exhaust vitiating the air, but if enough air is circulating in those parts of the mine in which the locomotive is used, these gases are so diluted that they are rendered harmless, and the health of the workmen is not affected. In some mines the use of gasoline locomotives is impracticable, though in the majority of mines where they have been tried they have proved to be safe and economical. To determine the limitations that should surround the use of these machines in mines so that they shall not be detrimental to health and so that their economic advantage may be retained, it is necessary to ascertain the volume and the character of the exhaust gases and the amount of these gases that may be safely allowed in the mine air, and also to determine safe conditions of operation. The problem is primarily one of ventilation and like all ventilation problems must be intelligently computed to meet the conditions of each mine. The investigation described in this bulletin was undertaken 'by the Bureau of Mines in an endeavor to obtain exact information on some of the basal questions involved in the use of gasoline locomotives in mines, this investigation being one of many that the bureau has been conducting in its efforts to increase safety and efficiency in mining.

Jan 1, 1915

Geophysical Abstracts 1 - 83 were issued in mimeographed form by the Bureau of Mines; Abstracts 87 - 111 were published in bulletins of the Geological Survey. Abstracts 112 and 113 were issued in mimeographed form by tine Bureau of Mines as Information Circulars 7256 and 7257. 1. GRAVITATIONAL METHODS 7004. Campbell, R. B. Florida's Geological Structure and Gravity. Proc. Florida Acad. Sciences for 1540, Gainesville, Fla., vol. 5, 1541, pp. 73-84.

Jan 1, 1943

By D. Harrington

As no cure is known for silicocis after it has developed, prevention is the only effective remedy. There are two main lines of approach to the problem of dust-disease prevention in industry - the engineering, through control of dust production, and the medical, through selection of workers by examination; success probably depends upon a combination of the two. Hatch (146) considers the following measures essential to a complete, well-balanced program of control of the dust hazard in industry: 1. Selection of workers by means of physical examinations in order especially to eliminate those with tuberculosis and other disorders of the respiratory system. 2. Reduction of the duct concentration below the standard of permissible dustiness through adequate moans of dust control and good housekeeping. 3. Limiting the frequency and duration of employment in the dusty occupations, thus reducing the rate of deposition of dust in the lungs. 4. Routine measurement of the effectiveness of the dust-control program by means of periodic medical examinations and duct surveys.

Jan 1, 1935

"Initiated as a part of the Bureau of Mines program for development of strategic minerals for national defense, various mines in the Poughkeepsie Gulch and Mineral Point mining districts were examined by C. R. Wilfley, W. R. Hamilton, .and N. E. Wvvlwy, Jr., Bureau Of 'Mines engineers, in July and August 1943, July 1944, and September 1945. In a subsequent report a proposal was made to evaluate this isolated area 'of some 15 square miles located in Ouray and San Juan Counties, Colo.Reconnaissance work in the area was begun in June 1946. Mapping and sampling were begun in July and was completed in Pougkeepsie Gulch and extended westward to include the Hendrick Gulch area of the east side of Ironton Park. Project work was recessed for the winter on October 15, 1946 after approximately 6 square miles of the Poughkeepsie Gulch,district been mapped and 801 samples had been taken.In this report the physical features, climate, and ore deposits districts are described, and a brief history of mining and production lead, zinc; and silver is given.The individual mines and prospects in, the area are described in detail.A list of patented claims and ownerships is given in appendix I, and analyses of samples are tabulated in appendix II.The San Juan preliminary project was directed by Paul T. Allsman, chief, Salt Lake City Branch, Mining Division and was supervised by William M. Traver, Jr., supervising engineer, Colorado Field. Office.Chemical analyses were made by the Salt Lake City laboratory under the direction of H.E. Peterson, chemist, and S. R. Zimmerley, chief, Salt Lake City Branch, Metallurgical Division.Harold A. Waddington, president, Great Divide Mining & Milling Corp., and Ernest Miller, owner, Como Consolidated Mines, were particularly cooperative in making available maps and data concerning their properties."

Sep 1, 1949

By B. M. O'Harra

Zinc smelting is frequently termed a ba.ckward art. The term is hardly true, for great progress has been made in recent years in the design and in the thermal efficiency of the retort furnace, in the quality of retorts, in the recovery of zinc, and in the ability to treat more impure and complex ores. The fact remains, however, that the peculiar physical and chemical properties of zinc have delayed such immense advances-large smelting units, high recovery, lowunit costs, and ability to treat low-grade ores-as have been made in the metallurgy of lead and copper. In current retort-smelting practice, the ores, if carbonates, are calcined to remove carbon dioxide; or, if sulphides, are roasted to remove sulphur. The sulphur must be eliminated as completely as possible, usually to less than 1 per cent. This means that the roast must be continued for a long time at a high temperature, with resulting high cost and small capacity per furnace. The roasted ore is mixed with about 50 per cent of its weight of reducer, which may be fine coke, anthracite, or nonbituminous coal. This mixture is charged into horizontal fire-clay retorts. The retorts used in this country are about 8 inches in internal diameter by 4 feet in length and hold 50 or 60 pou~ds of ore. The diameter of the retort is limited by the tirrie required for the heat to penetrate to the center of the charge; the length by the strength of the retort, which at the high temperature employed can not support the weight of the charge if the span is more than about 50 inches. The retorts are heated externally by coal, natural gas, qr ·producer gas to a temperature of 1,200° C. or more. The zinc oxide is reduced to zinc, which is volatile at this temperature, and passes into a conical fire-clay condenser. attached to one end of the retort, where it conde_nses to liquid zinc and is removed. Twenty-four hours are required for distillation, and because of the low heat conductivity of the retort walls 11.nd of the ore charge itself, the heat efficiency even of the most modern regenerative furnacei;; is only about 12 per cent. The retorts have a short life, 30 to 6Q days, at the high temperature required-; zinc losses are heavy, usually 10 per cent or more; and the proportion of impurities in the retort charge must be carefully controlled to prevent the rapid corrosion of retorts. For these reasons, much work has been done in an e:ff ort to, find cheaper and more efficient methods o.f recovering zinc from its ores. Various methods have been proposed for smelting in the blast furnace. Some of these contemplated the production of zinc vapor and its condensation to liquid; others attempted to produce liquid zinc directly by smelting under pressure. It is now realized that fundamental difficulties render these proposals impracticable. The electric furnace for smelting offers obvious advantages in the way of the efficient utilization of energy, large units, easy attainment of high temperatures, and the possibility of treating complex ores. E. H. and A. H. Cowles first suggested a design for an electric furnace for the reduction of zinc ores and patented their process in 1885. Their attention was soon directed to other uses for their furnace and nothing further of importance was done in the electric smelting of zinc until about 1900. Several investigators then started work upon various processes and had more or less success. The chief difficulty they encountered was the impossibility of obtaining more, than a small amount of the zinc as liquid metal because most of the zinc vapor condensed as blue powder. Interest in the electrothermic metallurgy of zinc increased, many patents on processes and furnace design were taken out, and the literature on the subject grew, until in 1914 and 1915 the problem seemed to be approaching solution. About this time the hydrometallurgy of zinc, the development of which had been lagging somewhat behind that of the electrothermic metallurgy, sprang into the limelight and a commercial process was soon perfected. This rapid development, perhaps aided by the war premium on the high-grade spelter produced by electrolytic deposition, distracted attention from electric smelting to some extent, though progress continued. With the perfection and standardization of the electrolytic process has come a better realization of its limitations, especially the necessity for large-scale operation ·and the difficulty of obtaining high extraction. Because of these limitations the electrothermic metallurgy of zinc still has a field of its own and in fac-t promises to become a strong competitor of both hydrometallurgy and retort smelting except under conditions highly favorable to the latter methods. Because of the imperfections of the retort and electrolytic processes and the promise that the electric furnace offers in overcoming these imperfections, the. United States Bureau of Mines, in cooperation with the Missouri School of Mines and Metallurgy, has undertaken a study of the electrothermic metallurgy of zinc.

Jan 1, 1923

By E. R. Andersen, F. E. Block, T. T. Campbell

This work was done to develop methods for increasing the yields and purity of vanadium prepared by bomb reduction of vanadium compounds . Compounds reduced were V₂ 05 , V203 , VC , and VC13 . Sodium , calcium , and magnesium were used as reductants . Variables considered included reductant form , bomb size , pressure during reaction , method of ignition , and the use of slag fluidizing additives . It was concluded that yields of 85 to 90 percent can be effected by the calcium reduction of V205 in reactors measuring as much as 14 inches in diameter and 60 inches in height . Optimum charge composition included V₂05 , 65 percent excess calcium , and 0.4 moles sulfur per mole vanadium . Purity of the vanadium produced in large reactors varied from 99.5 to 99.8 percent . The higher purity metal , depending upon the amounts of interstitial impurities present , was usually cold ductile . Although high yields of up to 99.5 percent can be effected by bomb reduction of VC1 , the high pressures developed in the bombs and attack of the reactor walls by the byproduct chloride slags discourages this method of preparing vanadium . It was found that significant purification of impure regulus metal occurred when it was hydrided , crushed , acid leached , and vacuum dehydrided . Metal so treated can readily be converted to ductile sheet . A cost estimate based on the production of 100 tons of vanadium per year was prepared . It was concluded that pure ductile vanadium could be produced for approximately $ 20.00 per pound .

Jan 1, 1964

By Lloyd A. Morley, Robert Stefanko

In addition to explosion-proof enclosures, the IEC has published recommendations: 1. 79-2 Pressurized Enclosures, 2. 79-3 Intrinsic Safety, 3. 79-5 Sand-Filled Apparatus, 4. 79-6 Oil-Immersed Apparatus, and 5. 79-7 Increased Safety. All these are valid methods of electrical hazard reduction and find wide use in industries other than mining. Magison (52) discusses in detail each technique and, therefore, such an examination will not be repeated. Two other systems, lamina and labyrinth, are but variations of common explosion-proof enclosures and, therefore, will not be cov¬ered. (34,35,46,53,54,61) By examining other national authorities' opinion, the following will investigate each system's applicability to coal mining. Intrinsic safety applies to any system which is incapable of re¬leasing sufficient energy to be an electrical hazard. (49) Not one foreign country contacted disagreed with the concept, and they find these systems totally acceptable. Only South Africa does not accept oil-immersed apparatus, but no reasons were given. (62) Healy (27) stated that Queenlands, Austrailia would accept all techniques, yet some were still to be employed. Japan specifications allow for all but sand filled. (42,43) Increased safety or Protection Type "e" is an approach in hazard reduction in which special design considerations are applied to ensure an extremely low probability of electrical or mechanical breakdown

Jan 1, 1974

By M. Didyk

The final objective of a mine ventilation project is to find a way of supplying the working faces with the necessary quantity of air to dilute all the possible air contaminants to safe limits and to maintain the temperature, humidity and oxygen content within desirable limits. To accomplish the aforesaid, decisions have to be made at early stages of planning and design of a mining operation. That is, ventilation and mine planning are closely related and interdependent, and experience has proved that improvisation as related to mine environment is rarely optimal in ventilation engineering. Mine management should be concerned with two general aspects of ventilation problems. The first is related to the statuatory requirements which are usually the minimum standards that have to be maintained. During the last two decades, mining laws have become increasingly stringent and management of operating mines had to face the effects of these externalities. In some cases these required either a production rate reduction or additional mine development. The second aspect that management should not overlook is the technical and economical importance of mine ventilation on the overall mining cost. In coal mining it is necessary to move, on an average, five tons of air through the mine for each ton of coal produced. The power cost incurred is perhaps the single most important direct cost assigned to ventilation but it is not the only one. Other costs that should be considered include the supervisory labor cost, fan depreciation and maintenance, doors, stoppings and regulators construction cost and maintenance, the additional mine airways development and maintenance because of ventilation requirements. That is,

Jan 1, 1977

By Gordon E. Green

This report addresses remote monitoring of coal waste impoundments for stability. Existing automated geotechnical monitoring systems are described and reviewed along with details of instruments suitable for such systems. An impoundment in West Virginia which was in the construction stage was instrumented and monitored between July 1979 and may 1981. Sensors which measure surface and subsurface parameters including settlement, horizontal deflection, surface tilt, pore water pressure, seepage, pond level, and meteorological parameters were installed. Data from the 37 sensors were collected by on-site logger and transmitted by telephone to a central processing station in Seattle for recording and interpretation. Difficulties were encountered with telephone and powerline outages and malfunction of electronic units. Detailed descriptions of the design and performance of the system are provided along with evaluation and comparison with other systems. Recommendations for improving and expanding the capabilities of the monitoring system are given.

Jan 1, 1982