Search Documents

By Richard L. Jenkins

Systematic sampling, in reconnaissance fashion, of the continental shelves of the United States to define favorable areas of offshore mineral deposits, is one of the long-range marine mineral; programs of the U.S. Department of the Interior. In mid-1966 the Department of the Interior launched its Heavy Metals Program to stimulate domestic output of gold which is in serious short supply. The program is jointly conducted by the Geological Survey and the Bureau of Mines.

Jan 1, 1968

By T. E. Gray

This report describes the preparation characteristics of the significant coalbeds in Nicholas County, W. Va. It is one in a series describing coals suitable for producing metallurgical coke, either as mined or after beneficiation. Almost 5 million tons of coal were produced in Nicholas County, W. Va., in 1960, of which over 2.6 million tons were cleaned in eight preparation plants. It has been estimated that over 6 billion tons remained in the county as of December 31, 1960, in beds 12 inches and more thick.

Jan 1, 1962

By A. M. Evans, J. H. Soulé

"INTRODUCTION Deposits of iron ore in Cherokee County, Tex., have been worked at various times in the pact, and the ore has been smelted in small local blast furnaces.Recently it was proposed to establish a charcoal blast furnace with a wood distillation plant to produce charcoal for fuel and byproducts. Financial assistance from the Reconstruction Finance Corporation was sought by George Easley and associates to enable them to purchase, move, and erect the furnace and build the required accessory plants. The furnace was to be moved from Pembroke, Fla.In August 1941, the Bureau of Mines was asked by the Office of Production Management to check the development work of Easley and associates and to ascertain (1) the iron-ore reserves, (2) the cost of mining ore and delivering it to the blast furnace, and (3) the grade and character of the ore. The Bureau of Mines was advised, while the investigation was in progress, that approximately 1,000,000 long tons of measured reserves would be sufficient to demonstrate the feasibility of operating the properties.Although deposits of iron ore are widely distributed in Cherokee County, only the Pryor Mountain, Banks and Cherokee, J. P. Acker, and Citizens State Bank tracts were sampled thoroughly by the Bureau of Mines. The iron-ore rights on these are owned by the New Birmingham Development Co., the Cherokee Development Co., or by individuals. Options to lease the ore rights were obtained by Easley, who obtained options on the Hawes Peach Orchard and Bradford tracts, also, which were examined only cursorily by the Bureau."

Aug 1, 1947

By Philip B. Grote

The deep ocean mining industry is in a pre-commercialization stage of development. In the context of a proper legal/regulatory regime, deep ocean mining system design, site survey, and operation technologies are capable of rapid evolution. The report recommends that the regulatory framework develop in parallel with the industry and presents a rationale for implementing this approach. The Government has several interests in deep ocean mining technology: (1) as a potential regulator, sound regulations should be based on an understanding of the technology; (2) as a potential monitor, survey technologies are relevant; and (3) as an estimator of strategic minerals supplies, it is important to understand the technology which allows economic access to deep ocean minerals. Thus, the major portion of the report presents an in-depth review of systems design, operations, and survey equipment and techniques.

Jan 1, 1979

By Charles H. Foreman

This paper describing the mining practice of the Hecla and Star mines, both located at Burke, Idaho, is one of a series being prepared by the Bureau of Mines on mining practices, methods, and costs in the various mining districts of the United States. It is partly a revision of articles by the author appearing in volume 72 of the Transactions of the American Institute of Mining Engineers, published in 1925, and in the June 1928, issue of the American Mining Congress Journal. About 26,000 tons per month of lead ore is produced at the Hecla mine. Costs at the mine are given for the year 1928. Stoping operations in the Star mine have covered such a short period, during which time the abnormal expenses of starting were incurred, that they are not given in this paper.

Jan 1, 1930

By John Nagy, Hylton R. Brown, Irving Hartman

"INTRODUCTION The tests described in this publication were planned to provide information on the explosibility of metal-powder dust clouds. This subject has become increasingly important because of the large quantity and variety of metallic powders now used for military and industrial purposes. To provide the increased amounts of metallic powders needed in the manufacture of munitions and to supply the demand created by the rapid growth of powder metallurgy, existing metal-powder plants have been enlarged, production schedules accelerated, and new plants erected. In some cases new methods of producing metal powders have been developed. This increased production and the development of new manufacturing methods have caused an increase in the number of metal-powder fires and explosions, with accompanying heavy loss of life and property. These have emphasized the need for information on methods of providing protection against hazards inherent in the production and handling of powdered metals. This paper gives results of laboratory inflammability and explosibility tests made to April 1, 1943, and is a progress report. Many descriptive details have been omitted purposely; they will supplied in a later publication, expected to be a Bureau of Mines bulletin."

Oct 1, 1943

By William L. Crentz

Pike County in the easternmost portion of Kentucky is one of the major coal-producing areas in the eastern Kentucky coal field. The county contains numerous coal beds, many of which are too thin to support mining. The commercially important beds are usually 4 feet or more thick, but selective mining at some places calls for removal of a much thinner section of the bed. The variation in quality of the beds from place to place and the large number of coal beds make correlation uncertain. Samples were collected from 14 different coal beds, of which the Elkhorn group is by far the most important. In addition to the Upper Elkhorn No. 3, Upper Elkhorn No. 2, Upper Elkhorn No. 1, and Lower Elkhorn beds that comprise the Elkhorn group, the Winifrede, Williamson, and Bingham beds constitute the principal coal deposits in Pike County.

Jan 1, 1952

By Eugene T. Sheridan

The Bureau of Mines annually canvasses the peat producers in the United States and publishes economic data on the industry, based upon reports from producers. This publication lists all producers that reported commercial production to the Bureau for 1959. The companies named herein represent virtually all commercial producers of peat. A few companies, however, may not have been canvassed or failed to respond, as tine survey is voluntary For producers, arid the industry has many small operations that operate intermittently. No consideration was given to the quantities of peat produced and output of the various companies listed ranged from less than 100 tons to more than 50,000 tons, Peat is included in the Bureau's annual surveys of the mineral industries because, technically, peat is a fuel. Although none is used for fuel in the United States, peat is a potential source of energy and one of our large mineral resources. The domestic peat industry produces peat chiefly for use as a soil amendment. The industry has expanded rapidly during the past decade with active operations increasing from 45 in 1947-49 4/ to 105 in 1959. Output during this period has increased 218 percent, rising from 131,782 net tons to 419,460 net tons.

Jan 1, 1960

By Herbert Haas

The Bureau of Mines is endeavoring to reduce waste and increase efficiency in the production, refining, and utilization of petroleum . During the last few years the demand for petroleum and its products has increased so much more rapidly than the production that greater efficiency in utilization is now a matter of most serious importance . The Diesel engine, a comparatively new type of internal-combus- ' tion engine, is an important device for insuring more efficient utilization of petroleum and coal-tar products, for it consumes heavy liquid fuels such as can not be utilized in other types. Like the gas or the gasoline engine, it is revolutionary within its province. For some uses this engine is replacing gas and gasoline engines , but its most important duty will be to replace the wasteful consumption of fuel oil in steam engines. Not only will a wider use of the Diesel engine relieve the demand, but it will result in more power being obtained from the same consumption of fuel oils . In spite of these advantages, comparatively few Diesel engines are in use in the United States . In this report the author discusses recent developments in the design and construction of the Diesel engine, the fuels suitable for burning in it, and the uses to which it is particularly adapted .

Jan 1, 1918

By W. C. McBee

Technology for the preparation of densifiable sulfur concrete (sulfapave) materials has been devised by the Bureau of Mines. The materials are intended as new construction materials for use in corrosive areas where conventional materials fail. A series of modified sulfur cements were developed, which can be used in combination with dense-graded aggregates to prepare sulfapave materials with excellent corrosion-resistant properties. The materials can be mixed, laid, and compacted into place with conventional hot-mix asphalt pavi.ng equipment. Mixture designs utilizing 5-to 30-pct-modified sulfur cements and dense-graded aggregates gave material properties ranging from rigid to flexible. Laboratory corrosion tests in sulfuric acid showed no material loss or deterioration of physical properties over a 1-year test period in concentrations ranging from 0 to 60 pct at ambient temperatures. Preliminary results on field testing the materials for durability to weathering, corrosion, and traffic have been excellent, with no evidence of failure in the materials.

Jan 1, 1985

By J. P. McGee

As part of a joint U.S. Atomic Energy Commission-Federal Bureau of Mines program for using nuclear energy to supply process heat, a simulated nuclear loop has been constructed to test components. This loop has been operated for more than 1,800 hours at 100 p.s.i.g. Of this period, 23 hours were at 2,500° F. and higher; 540 at 2,000° to 2,500° F.; 840 at 1,500° to 2,000° F.; 200 at 1,000° to 1,500° F.; and 260 below 1,000° F. Leakage at flanges and welds was not a serious problem. A helium-recycle system with gas temperatures of 2,300° to 2,500° F. and a static pressure of 250 p.s.i.g. appears feasible. Difficulties were encountered with the recycle compressor due to thermal distortion of the impeller and shaft. The use of sealed bearings limits compressor operation to the life of the bearings.

Jan 1, 1960

By Philip Thompson

A part of the Bureau of Mines mission is to help improve the Nation's mineral posture by providing the technology for utilizing low-grade ores. In this regard, laboratory testing by the Bureau of Mines has shown that the removal of insoluble slimes using selective flocculation and flotation is a viable method for treating low-grade potash ores that have a high content of water-insoluble impurities. Results indicated that over 82 percent of the insoluble slimes could be removed from sylvinite ore containing 5 percent water insolubles and 13 percent K20 by using nonionic or cationic polyacrylamide flocculants and cationic, anionic, and/or nonionic collectors. Subsequent potash flotation recovered 87 percent of the potash in rougher concentrates containing 57 percent K2O. Sizing and cleaner flotation of the rougher concentrates upgraded the products to 60 percent K2O. Filtration of the water-leached insoluble-slimes flotation concentrates on a bed consisting of leached insoluble-slimes concentrate mixed with potash flotation tailings recovered 80 percent of the brine. Filtration rates using the mixed bed were nine times faster than filtration rates obtained when the insoluble-slimes flotation concentrates were filtered separately.

Jan 1, 1979

By Donald F. Reed

In its investigation of old, abandoned, lead-zinc mines at which records of operations are not available, in 1914 the Bureau of Mines dug surface trenches anti', in 1947 It diamond-drilled three holes at the Albright Farm deposit in Sinking Valley. Some good lead-zinc ore had been extracted from veins in dolomitic limestone during the time of the American Revolution and as late as 1870. Since that time the only activity was sporadic prospecting and developing. Thu Bureau of Mines disclosed two additional veins by surface trenching, but diamond drilling failed to find significant lead-zinc mineralization.

Jan 1, 1949

By Wm .. O. Vanderburg

This paper describing the mining practices at the Block P mine of the St. Joseph Lead Co. at Hughesville , Mont . , is one of a series of similar papers being prepared by the Bureau of Mines on mining practices , methods , and costs in the various mines of the United States .

Mar 1, 1931

By D. Harrington

The occurrence of dust in mines has always been a source of trouble, but for any years, and virtually up to the beginning of the present century, relatively little of a definite nature was known as to the numerous ill effects of dust in mining operations. Even today, with the west amount of time given and attention paid (for at least 40 years in various, countries) to research and observation en dust in mining, and in spite of the experience with it, much information remains to be obtained, before definite, well-authenticated statements can be made as to numerous features connected with the occurrence of dust in Dines an of its effect upon the health and safety of the worker. One statement that can be made with relatively good assurance of being uncontradicted in that dust is a real menace to the well-being of mine workers, and this includes both health and safety. In addition, dust in and around mines and mining plants is one cause of large financial losses to mine owners and operators. FORMATION OF DUST IN COAL MINES IN THE UNITED STATES One definition of mining is "the processes by which useful materials are obtained from the earth's crust; " since virtually all of the useful materials of or in the earth's crust either are solids or must be reached by penetrating through solids, the materials that are moved in mining must necessarily be broken or disrupted, so that almost every phase of the work of loosening the material and transporting it is likely to produce dust.

Jan 1, 1939

This manual provides instructions for installing, operating, and maintaining a protective canopy on the Joy Mfg. Co. loader. These instructions are based upon two actual install .at ions: one made in a mine on loader, model 14BU10-11AH, and one in the factory on model 14BU10- 11AH. The parts list and engineering drawings for the protective canopy are included at the end of the manual. And a discussion of some alternative design concepts is also included. The manual can also be used for retrofitting other loaders with similar protective canopies. Skilled mechanics can determine if the instructions herein would be applicable to the other loaders and can determine any necessary modifications if they are not.

Jan 1, 1973

This Volume documents the Phase 111 effort on the Seismic Detection and Location of Isolated Miners on Contract H0122026 undertaken during the fall of 1972 by a task team composed of ADL staff and several seismic consultants. The team was assembled specifically to work together on complementary tasks, at an accelerated level of effort for four months, to meet the Bureau of Mines' time schedule for obtaining independent, objective, technical judgments regarding seismic methods and systems for detecting and locating isolated miners. The impetus for this work resulted from a compilation and analysis, during the first half of 1972, of new experimental data obtained from a series of in-mine field tests conducted by Westinghouse Corp .+ using the CMRSS* interim seismic location system. The Bureau of Mines took advantage of the availability of these new data to reassess the potential and limitations of various seismic methods and systems, and to direct its seismic system improvement program accordingly. ADL assisted the Bureau in this reassessment by drawing on the skills of seismic consultants from industry, universities and government, to supplement the skills of the ADL project team. The consultants were principal resources of broadly-based and detailed technical expertise in the areas of seismic signal-source and signal-propagation characteristics, natural and cultural seismic noise, seismic sensors and field instrumentation, seismic signal and data processing for detection and location, and overall seismic system utilization in the field under operational emergency conditions. Specifically, the participating consultants were: F. Crowley, Air Force Cambridge Research Laboratories ; W. Dean, Teledyne Geotech, Alexandria Laboratories; R. Greenfield, Pennsylvania State University; J. Kuo, Columbia University; D. Peters and R. Crosson, University of Washington; and F. Pilotte, U.S. VELA Seismological Center. The principal ADL participants were J. Ginty, R. Lagace, M. Roetter, and R. Spencer.

Jan 1, 1974

By D. W. Frommer

Processing of nonmagnetic taconites by selective flocculation-des liming and anionic flotation of calcium-activated silica has been investigated using innovative procedures as a means of improving operating costs. Areas chosen for cost-cutting evaluation were grinding, fine screening, and water conservation and reclamation. The investigation was performed on Marquette range nonmagnetic taconites in the Bureau of Mines Twin Cities Metallurgy Research Center flotation pilot plant, at feed rates ranging between 900 and 1,100 lb/hr. With fully integrated water reclamation, flotation concentrates containing 65.8 percent Fe and 3.4 percent Si02 were made in the best operating period, with accompanying weight and iron recoveries of 40 and 74 percent, respectively. During this same period, the estimated cost of both flotation and water reclamation reagents was only $0.80 per ton of concentrate (1968 pricing basis). This cost is about 15 percent lower than obtained previously at this Center for flotation reagents only. The investigation demonstrated additional potential savings in operating costs of approximately $0.96 per ton of concentrate through autogenous grinding as a substitute for ballmilling. Fine screening of intermediate concentrates was employed advantageously, but the frequency of blinding may be a factor militating against use of the screen in this flotation system.

Jan 1, 1973

By E. L. Rawlins

The development of commercial natural-gas reserves in the Michigan stray sandstone horizon of central Michigan during the past few years has resulted in expansion of the natural-gas industry in that State. The location of the natural-gas reserves of Michigan in the general vicinity of domestic and industrial markets is of economic importance, and in supplying these markets with natural gas a reasonable knowledge of, the extent and availability of the reserves is needed in formulating regulations for drilling gas wells and producing natural gas in analyzing the feasibility of projects to construct natural-gas transmission lines, in promoting and developing markets for the domestic and industrial consumption of natural gas, and in solving many engineering and economic problems common to the natural-gas industry. The development of the natural-gas industry in Michigan has been related closely to the development of oil production. The potential oil production of Michigan is comparable with that in most of the eastern oil-producing States. The development of oil production probably will continue, especially in the central Michigan Basin area; and as wells are drilled to deep horizons in the search for oil, more knowledge will be obtained of the gas reserves in formations above the oil-bearing horizons.

Jan 1, 1936

By Zsuzsanna Zborovszky

Study of the energy transfer from an inductive circuit to the discharge under the conditions of the minimum discharge voltage being smaller than the source voltage. Analysis of the effect of the electrode separation speed on the duration and maximum power amplitude of the discharge. Recommendation for optimal electrode setting. Experimental data on the variation of maximum discharge power required for ignition as a function of volumetric gas content for methane-air and propane-air mixtures. Experimental determination of the ignition limit for discharges derived from a 24, 15, 10 and 6v inductive-resistive circuit in 8.3% methane-air mixture by using the PTB breakflash with Cd disc and W wires, and also with Cu disc and BeCu wires. Method for calculating ignition limits for other source voltages.

Jan 1, 1978