Search Documents

By David E. Nicholson

In a Bureau of Mines investigation of the dynamic compaction of mine hydraulic backfills, two basic forms of mechanical vibration inducers were used and compared for effectiveness of compaction. Internal compaction, using concrete probe vibrators of various sizes, and external compaction, using plate vibrators} were studied and evaluated for use in underground stopes. An aluminum plate, which was light and displaced sufficient volume to remain afloat in fluid fill, and a steel plate were both used in the external compaction tests. Efficiency of compaction was better in studies conducted with internal probe vibrators. Tests were conducted in an underground backfilled stope with three different-sized probe vibrators (2-, 4-, and 6-inch-diameter) to determine an approximate area of influence. Results showed the areas of influence to be approximately 3, 4, and 5 feet in diameter, respectively, for the three different probes. Physical properties of hydraulic slurries were determined; preferred grain-size distributions, water exudation properties, and water contents of hydraulic slurries are reported. The best compaction results were obtained with moderately well-graded, fully saturated backfills, with slow rates of water exudation, which were capable of remaining in a semifluid state during the compaction process.

Jan 1, 1967

As a part of its overall wealth in fuel resources, the United States possesses large reserves of coal of ignite rank. According to recent estimates of the Federal Geological Survey (3, 5),l/ the assured lignite reserves of this country amount in total to over 463 billion tons, equivalent to 24 percent of our total national coal reserve on a tonnage basis and 15 percent on a heating-value basis. Distribution and relative amounts of United States coal and lignite reserves are indicated in figure 1. By far the largest proportion of our lignite reserves, over 95 percent is found in North Central States, principally in North Dakota, South Dakota, and Montana, in the vast coal-bearing structural grouping designated as the Fort Union formation. Of the remaining United States reserves, all but a fraction of 1 percent are found in a series of relatively scattered deposits in Texas.

Jan 1, 1954

By Don M. Coulter

"INTRODUCTION Bauxite, in Appalachian Alabama, occurs in the Rock Run and Goshen Valley districts in Cherokee County; in Nences Creek Valley near Jacksonville; near Anniston in Calhoun County; north of Fort Payne in DeKalb County; near Ashville in St. Clair County; and near Talladega in Talladega County.In February 1942, Preston E. Cloud, Jr., assistant geologist, Federal Geological Survey, began a study of these bauxite deposits and the geology relating thereto.The Bureau of Mines established field headquarters at Piedmont, Calhoun County, in July 1942. Mineral agreements covering a total of 11,097 acres were executed with 15 landowners in the Rock Run district; 38 in the Goshen Valley district, covering 7,575.5 acres; and 3 in the Nances Creek Valley district, covering 988.5 acres. Drilling was done on the properties of 9 land¬owners in the Rock Run district, and on the property of 1 landowner each in the Goshen Valley and the Nances Creek districts. Drilling began October 26, 1942, and ceased on May 17, 1943.Power drilling was supplemented by a labor crew that drilled hand-auger holes in shallow deposits and sampled .old shafts, mines, and mine dumps.In all, 222 holes for a total of 13,250 feet were drilled. Of these holes, 88 penetrated bauxite but too low in grade to constitute ore."

Mar 1, 1948

By Thomas E. Popplewell

This paper is one of a series being prepared for and published by the United States Bureau of Mines describing the mining and treatment methods and costs obtained in sand and gravel plants throughout the United States. These papers are designed to disseminate technical information regarding the methods used. The cost tabulations represent operating expenditures only and not total costs. It is recognized that publication of total costs might in many instances cause embarrassment to individual operators as well as to the industry as a whole. On the other hand operating costs are essential to the technical discussion and study of the methods employed. The attention of the reader is specifically called to this differentiation in order that no misunderstanding of the scope of the cost tabulations shall ensue.

Jan 1, 1932

By Michael V. Markel

This report summarizes work performed under USBM Contract No. J0100047 revealing the performance characteristics of a composite-type resilient screen deck. The ability of the composite to perform or compete with steel in noise attenuation and longevity was of interest. Tests were conducted at the River King Preparation Plant of Peabody Coal Company. This facility was chosen because it provided parallel process flow and met standard coal cleaning requirements. Comparisons could be made between the adjacent resilient and steel screen decks under similar operating conditions. Noise reductions of 1-6 dBA were realized in the near field. Although the test period did not determine resilient screen life, indications are favorable for their longevity.

Jan 1, 1981

By Neil J. Mansfield

Tool manufacturers are required to provide declarations of vibration emission values in order to sell their tools within Europe. To ensure that users can compare results obtained from different manufacturers, the declared values must be obtained using a methodology as specified in the relevant test code (such as in the ISO 8662 series of standards). In most cases, the vibration emission values obtained using test codes under-estimate the vibration that an operator will be exposed to when using the tool on a work-site. A further problem with manufacturers’ data is that usually only a single value is provided for a tool. This is despite many factors affecting the vibration emission, including inserted tool type, work piece, operator technique, tool condition. New improved test codes are in the process of being developed. In order to provide guidance to users on how to interpret manufacturers’ data, a Draft CEN Technical Report (Draft CEN/TR 15350 (2005)) was developed. Part of the CEN/TR provides multiplication factors for combinations of task and tool type. For example, data obtained from electrical hammer drills (tested according to EN 60745-2-6:2003) should be multiplied by 2, for hammering applications, in order to obtain an estimate of the vibration emission during work. In response to concerns from industry, the UK trade association OPERC have, in collaboration with hire companies and tool manufacturers, established a freely accessible online database of tool emission values based on independent tests carried out under simulated work-site conditions. This paper reports some of the data obtained from electrical hammer drills, highlighting the range of emission values that can be obtained for a tool. Data from many other tool types are also included in the database. Methods Tri-axial hand-arm vibration was measured at both handles of each of 19 electrical hammer drills, in accordance with ISO 5349-1 (2001). Each tool was measured with three experienced operators and at least 5 runs were completed for each operator. Tools were tested using a range of appropriate new bits from 4 to 40 mm diameter. The minimum number of bits for a tool was 3; the maximum number was 29. 146 tool / bit combinations are reported here, representing about 2200 individual 6-axis measurements. Operators were required to drill vertically into a concrete block with a compressive strength after 28 days of 40 N/mm². Two drills (1 and 15) were battery powered; others were powered using a 110V transformer supply.

Jan 6, 2006

By F. N. Kissell, C. D. Litton

Abstract-This study predicts the level of smoke that miners might meet while trying to escape a coal mine fire and describes how smoke would impede their safe escape. For this study, the authors assumed that miners exit through an escapeway adjacent to the burning entry, that some air would leak from the burning entry to the escapeway. The following conclusions were made: • A very low amount of air leakage to the escapeway can produce a critical level of visual obscurity from smoke. This shows that intake airways may be as susceptible to smoke visibility problems as return airways. • This critical level of smoke obscurity is reached much before a critical level of carbon monoxide is reached. • Small fires can cause a severe sensory irritation that further limits vision. Thus, reliable eye protection is very important. These results show that methods to guide miners through dense smoke will contribute greatly to saving lives during mine fires.

By A. W. Fahrenwald

The purpose of screening is to separate a crushed or natural product into one or more products in which size of grain is constant, or within certain size limits. The ore dresser finds need for this operation in the laboratory, in the study of ore-dressing processes, and for various purposes in the plants. In the plant, for example, screens are employed in closed circuit with crushing devices such as rolls, and sometimes are used in closed circuit with ball mills. Screens are generally used to prepare jig feed where a sized feed is wanted. For any given sieve opening there is in any feed a certain percentage of grains that will pass through the sieve meshes only with difficulty and under favorable conditions. For example, cylindrical grains of length greater than the maximum dimension of the sieve mesh and of diameter less than the sieve opening pass the sieve only when the long axis of the grain is normal or nearly normal to the sieve. Whether such grains should actually be in the through's or the oversize of a screening operation--considered from the point of view of the subsequent treatment of the grains--can not be said. The grains that pass the sieve opening in a screening process only under-favorable conditions have been named "difficult" grains by R. K. Warner.4 In many ore-dressing flow-sheets it probably matters little whether these difficult grains show up in the screen through's or oversize. The main objection to them is that they are sieve-blinding.

Jan 1, 1929

By Frank B. Fulkerson

A study was made of the economic factors governing silver production in the Coeur d'Alene mining region, Shoshone County, Idaho. Production and other statistics were analyzed. It was concluded that if the rapid rise in the open market price that began late in 1961 continues, greater production of the metal should result from the mines of the Coeur d'Alene mining region. However, the output gain would be limited, because costs per ton of ore mined would rise as production was increased beyond optimum capacity. Advances in the price of silver would increase the size of ore reserves by making some marginal ore profitable to mine and by providing greater funds for exploration projects that might result in discoveries adding to the reserves. Output of byproduct silver from Lead-zinc mining probably will not exceed 4.3 million ounces, judging from the trend from 1946 to 1961.

Jan 1, 1964

By C. O. Anderson, W. M. Meyers

Since 1922, when a brief report3 on the production and utilization of garnet was issued by the Bureau of Mines, there have been a number of interest—in developments in the technology of that mineral. Greater activity has been displayed in mining, new mills have been erected, and more attention has been paid to improvements in milling so that a more efficient and economical recovery of garnet has been possible. These activities have resulted in larger production; therefore, attempts are being made to broaden the market for garnet abrasives, and to find new uses for the unusual combination of physical properties than this mineral possesses. The writers have recently completed a field study of the occurrence, methods of mining and milling of garnet, and the manufacture and utilization of abrasive garnet products. This preliminary report indicates the most important sources of garnet, the methods by which it is recovered, and the manner in which it is recovered, and the manner in which it is utilized.Chemical and Physical Properties.The term ""garnet"" is applied to a closely related group of minerals which crystallize in the caste forms and possess similar physical properties, although their chemical composition may exhibit greater variation. The chemical composition of the garnet group may be represented by the general formula 3R"" O.R""' 203.3S102, in which R represents the bivalent elements calcium, magnesium, in the manganese state and ferrous iron, R"" represents the trivalent elements, ferric iron, aluminum and chromium in the chromie state. An account of the amorphous substitution of the different bivalent and trivalent elements, specimens whose composition may be represented by a definite formula are rare, the composition of any given specimen generally exhibits treat complexity.

Jun 1, 1925

By Elaine T. Cullen

Miners, like many skilled blue-collar workers, are not traditional learners. They have not generally been successful in classroom-type settings, preferring to learn on the job in a hands-on environment. U.S. miners are required to have annual safety training, but they rarely view this positively. In fact, it has been called “safety jail” by many of them, who regard it as a time to get a little extra sleep. The challenge then, was to find a way to develop effective safety training for these people, particularly in view of the fact that their work is among the most dangerous of all occupations. Miners are born story tellers. They share “near-miss” stories, stories about master miners they have known, and stories about how things used to be. These stories not only pass along information about what will happen if a miner fails to respect the mining environ-ment, they also instruct listeners in the culture of mining and the values it embraces. Stories, it seems, are a way to get safety messages to miners, especially inexperienced ones, and using older, wiser miners in these stories is an obvious choice. This paper will discuss how the training videos created to get safety messages to miners were developed, how “master miners” and story lines were chosen, and how the resulting videos have been received in the mining industry.

By S. M. Runke

The pegmatite investigations at the Rapid City, S. Dak., Experiment Station during; the pact 3 years have been primarily a study of recovering beryl from nonlithium-bearing pegmatite rock by continuous-testing methods. Beryl concentrates containing 25 to 88 percent beryl were produced from rock that ranged in beryl content from 0.1 to 2.5 percent. The beryl recovery ranged upward from 70 percent but averaged better than 80 percent. Although promising results have been obtained with flotation methods for upgrading these concentrates to standard specifications, additional work is needed to improve and simplify the procedure. In addition, it was demonstrated that several potentially useful coproducts could also be recovered from pegmatite rock. The principal coproducts were mica, feldspar, and quartz. A heavy-mineral product also was made from pegmatites containing tin, tantalum, and columbium. The recovery if these minerals in products meeting the specifications of the commercial users has been reserved for future study. The investigations also included studies on extraction of beryllium from both high-grade beryl and flotation concentrates of medium beryllium content. The procedure investigated consisted of sintering beryl or beryl flotation concentrates with limestone, acid curing the resulting sinter with sulfuric acid to dissolve the beryllium, and water leaching to extract the beryllium. Over 90 percent of the beryllium was extracted by this procedure. Most of the optimum conditions and quantities of reagents were determined for dissolving the beryllium. As aluminum and iron also were taken into solution by the acid, further research is needed on methods of recovering high-grade beryllium salts from the solutions containing these elements.

Jan 1, 1957

By D. J. Dollhopf

An overburden handling dragline operation was conducted at a strip mine near Colstrip, Montana. The objective of the demonstration was to determine the degree a dragline could mix overburden inhibitory zones during the spoiling process. In order to quantify the mixing process the overburden was: 1) scatter spoiled; 2) dump spoiled; and 3) spoiled in a normal manner. This demonstration was part of an effort to investigate means of reestablishing non-polluted hydrological systems in areas where surface mining directly impacts shallow ground-water resources. When inhibitory material constituted < 5% of the total overburden volume, such material was essentially not detectable in the resultant spoil pile. When inhibitory material exceeded 15% of the overburden volume it was always found in the resultant spoil pile, generally with a smaller extent, indicating partial dilution. Inhibitory overburden zones often reappeared at the base or top of spoil piles in the potential aquifer and root zones suggesting the need for selective placement procedures. Scatter spoiling did not appear to be significantly more effective than normal spoiling, however clump spoiling seemed to produce less mixing of inimical zones. Mining activity has reduced ground-water levels within 1600 m of the active pit. The aquifer which is developing in spoils appears to have similar confinement characteristics as those that existed in the premined aquifer. To date no definite trends have been observed concerning changes in surface or ground-water chemistry associated with mining.

Jan 1, 1978

The U.S. Bureau of Mines (USBM) was established in the public interest to conclude inquiries and scientific and technologic investigations on mining and the preparation, treatment, and utilization of mineral substances; to promote health and safety in the mineral industries; to conserve material resources and prevent their waste; to further economic development; to increaseee efficiency in the mining, metallurgical, quarrying, and other mineral industries; and to inquire into the economic conditions affecting those industries. The organic act of the Bureau, as amended by Congress and approved February 25, 1913, made it the province and duty of the U.S. Bureau of Mines to "disseminate information concerning these subjects in such manner as will best carry out the purposes of this Act." In accordance with this directive, USBM reports the findings of its research and investigations in its own series of publications and also in articles that appear in scientific, technical, and trade journals; in proceedings of conventions and seminars; in reference books; and in other non-USBM publications. The number of these reports, the wide range of subjects they cover, and the variety of mediums in which they appear make this kind of list both necessary and valuable. This edition describes reports and articles published during calendar years 1992 and 1993. It supplements the 50-year list of Bureau publications from July 1, 1910, to January 1, 19602; and these 5-year lists of publications and articles: from January 1, 1965, to December 31, 1969\ from January 1, 1970, to December 31,19745, from January 1, 1975, to December 31, 19796, from January 1, 1980, to December 31,19847, and from January 1, 1985, to December 31, 19898?.

Jan 1, 2007

The purpose of this study was to examine the problems of underground coal mining in the United States, and to develop recommendations for an integrated Research and Development Program aimed at resolving these problems. Specific objectives of the study were as follows: ? To identify the existing inadequacies that have adverse effect on Health, Safety, External Environment, and Productivity. ? To identify opportunities for technological advance s to correct these inadequacies. ? To develop an integrated Research and Development Program designed to accomplish the advances identified. Many of the recommended tasks are dearly long range; this is especially true of those for study of future mining systems. However, funding recommendations in this Report are presented for a 5 -year period, since the developments accomplished during this period will undoubtedly be a factor in the formulation of the follow on tasks. Where applicable, the recommended Research and :Development could include development and test of pilot model equipment.

Jan 1, 1970

By Alla D. Mah

Energies of combustion of vanadium nitride (VN) and vanadium carbide (VC) were measured. Correcting to vanadium tetroxide (V204) as the final state, the heats of combustion were ?H298.15=-118,700±100 cal/mole of vanadium nitride and ?H298.15=-240,270±360 cal/mole of vanadium carbide. With vanadium pentoxide (V205) as the final state, the heats of combustion were ?H298.15= -133.440±100 cal/mole of vanadium nitride and ?H298.15=-255,020±360 cal/mole of vanadium carbide. Combining these results with vanadium oxide data, the heats of formation obtained were ?298.15=-51,880±200 cal/mole of vanadium nitride and ?H298.15=-24,350±400 cal/mole of vanadium carbide. Heats and free energies of formation of vanadium nitride and carbide were calculated to 2,000° K.

Jan 1, 1963

By H. S. Caldwell

The objective of this investigation by the Bureau of Mines was to develop and test for laboratory use a retort embodying many features required for practical commercial-scale applications of vacuum distillation of metals. A gas-fired vacuum retort was developed comprising a hollow, cylindrical graphite liner encased in a thin shell of stainless steel. The liner prevents the shell from collapsing under vacuum and protects it from corrosion by metal vapors and the molten metal charge. The vacuum-tight shell protects the liner from oxidation and flame erosion. The retort was used to distill zinc from dross and die-casting scrap. More than 99 percent of the zinc was recovered as a condensate containing 99.8 to 99.9 percent zinc. (Atmospheric distillation recovers 95 to 98 percent at a purity of 99.5 percent zinc.) Distillation rates of 50 pounds of zinc per hour were attained at a temperature of 65° C. with pressures ranging between 50 and 100 microns. Distillation at this low temperature is not practicable at atmospheric pressure. Also, the retort is suitable for distilling other volatile metals such as cadmium and magnesium.

Jan 1, 1961

By John Ward Smith

The potential economic value of oil shale depends on the products from thermal degradation of the rock, because no other practical method for producing valuable material from oil shale has been found. Detailed study of thermal degradation behavior can aid in characterizing oil shales and their deposits and in evaluating oil-shale processing methods, Numerous publications describe various pyrolysis properties of oil shales (see surveys 3, 9, 11 and articles 1, 2, 4-8, 10, 12),4 but they do not describe a generally applicable analytical procedure for detailed evaluation of thermal degradation products. The analytical method presented here for such evaluations is designed to provide for: 1. Control of retorting conditions--temperature, heating, rate, reaction atmosphere--plus some control over retort pressure and carrier-gas flow, 2. Precise direct gravimetric measurement of the thermal degradation products--oil, water, gas, and spent charge (residue after thermal treatment of the charge). 3. Samples of all products. 4. Determination of the identities and amounts of gaseous compounds produced. 5. Elemental analysis and gross heating value of all products. 6. Determination of the distribution in the retorting products of the elements present in the original samples.

Jan 1, 1962

By Edwin C. Reeder

This is one of a series of papers dealing with mining methods and costs prepared under the sponsorship of end in cooperation with the United States Bureau of Mines. The mining methods described in this paper are those used in one of the large mines producing fluorspar in the Kentucky-Illinois fluorspar field, located in southern Illinois and western Kentucky on the Ohio River. The occurrence of ore and the methods of wining are similar to those in other mines in the district; therefore information regarding methods and the results obtained should be of interest. Improvements in methods have been made as experience developed the need of them. The trine is situated at Rosiclare, Ill., on the Illinois Central Railroad, and shipments are also made b r barge on the Ohio River.

Jan 1, 1930

By G. L. Oldright

The data in this paper were collected at the Trail smelter of the Consolidated Mining & Smelting Co. of Canada, Limited, through the courtesy of S. G. Blaylock, vice president and general manager; James Buchanan, smelter superintendent; George Murray, assistant smelter superintendent; and the staff members given in Paper XI, Report of Investigations 3243. INTRODUCTION This paper is the thirteenth of the series on Smelting in the Lead Blast Furnace, and the third of the series on Handling Zinciferous Charges. Tyro other papers have been written on the Rate of Descent of the Stock Column, and Formation of Accretions. These are Reports of Investigations 2963 and 3094, for the Tooele plant and the Bunker Hill plant, respectively.

Jan 1, 1934