Search Documents

By Stephen E. Mosher, Suzanne D. Smith

Ground, air, and water vehicles can expose humans to substantial multi-axis vibration. Multiple input/multiple output relationships or models exist for estimating frequency response functions of linear systems1, 2. These relationships have been applied by some investigators to evaluate the effects of occupied seat vibration3, 4. Using a multiple input/single output model, this study investigated the effects of single- and combined-axis vibration in the fore-and-aft (X), lateral (Y), and vertical (Z) directions on vibration transmission to the human chest. Frequency response functions (transmissibilities) were estimated and compared for the back-on and back-off postures. Methods A rigid seat with seat back was mounted onto the Six Degree-of-Freedom Motion Simulator (SIXMODE). A flat acceleration vibration signal was generated between 2 and 40 Hz at 1.0 ms-2 rms in the single and combined X, Y, Z, XY, XZ, YZ, and XYZ axes. The signals were shifted in time so that the combined inputs were not fully correlated. Lightweight triaxial accelerometers were used to measure accelerations at the seat base (input) and at the bony manubrium of the chest (output). The maximum of nine frequency response functions (H(?)) or transmissibilities were estimated from the auto- and cross-spectra. The system transfer matrix for the XYZ inputs and chest Z output is [ ] where PxZ, PyZ, and PzZ are the cross-spectra between the three inputs at the seat base and the Z output at the chest, respectively, and Pxx, Pxy,…zz are the auto- and cross-spectra between the input signals (? not shown in Eq. 1). Equation 1 can be similarly written for the chest X and Y outputs. Matlab® was used to estimate the auto- and cross-spectral densities for calculating the transmissibilities, ordinary coherences (for single inputs), partial coherences, and multiple coherences. Results Figure 1 illustrates the major chest transmissibilities observed for the two postures. Vertical vibration showed a consistent influence on the chest X response (Chest X/Z), most likely causing chest pitch. Some chest Z responses were observed with X-axis inputs, but the results were variable and difficult to interpret. In general, other factors besides the known inputs did not affect the transmissibilities shown in Figure 1 (Repeated Measures ANOVA, P<0.05). This was

Jan 6, 2006

By Leonard F. Heising

Domestic production of Metallurgical-grade manganese has contributed such a small percentage of the United States industrial demands that areas known to contain large tonnages of low-grade manganese ore have been investigated by the Bureau of Mines to reduce this country&apos;s dependence on foreign ores. A major source of low-grade manganese is the Cuyuna iron range in Minnesota. The entire Cuyuna iron range is covered by an overburden of glacial drift that, in some places, reaches depths of 200 feet or more. Prospecting and exploration must be guided by geophysical methods, drilling results, or projections of exposures found in operating mines because there are no outcrops near the productive parts of the range. Past drilling for the purpose of outlining iron ore generally was confined to the highly oxidized zones. Much of the manganese with which the Bureau of Mines is concerned occurs in thin-bedded unoxidized iron formations, too low in iron content to have been of interest to those seeking commercial iron ore. The primary objective of the core-drilling reported here was to obtain cores of different classes of manganiferous rocks and to determine whether or not the samples were amenable to beneficiation.

Jan 1, 1959

By D. Harrington

During the 5-year period 1906-10 inclusive, 84 major disasters (a major disaster being one in which 5 or more lives are lost) occurred in the coal mines of the United States, or an average of 17 per year, and the total number of fatalities from coal-mine gas and dust explosions (major plus minor) for the 5 years aggregated 2,338 or 477.6 per year. The monotonous continuance of coal-mine disasters month by month aroused the people of the United States to such an extent that it was felt necessary for the Federal Government to try to do something looking to the avoidance of the admittedly excessive loss of life in our coal mines, and this was one of the deciding factors in the establishment of the United States Bureau of Mires in 1910. That results have been obtained in this particular cause of coal-mine accidents may be seen from the fact that for the year 1933 but one major explosion disaster occurred in the coal mines of then united States and the total number killed in that disaster was 7. Unquestionably the coal-mining industry through use of oaf or mining practices and aided by the various kinds of work of the Bureau of Mines looking to the prevention of mine fires and explosions is in large part responsible for this very creditable change. If the gas and dust explosion fatality rate of 1.059 per million tons of coal produced during the period 1906-10 inclusive had continued to the first of January 1934, instead of the 6,373 deaths which actually occurred due to gas and dust explosions, there would have been 13,480. Hence, during the 23 years existence of the Bureau of Mines there has apparently been a saving of about 7,102 probable deaths, or an average of more than 300 per year, from gas and dust explosions as against the number which would have occurred had the 1.059 gas and dust explosion fatality rate for the period 1906-10 continued. Thirty-nine persons were killed in all kinds of explosions (both major and minor) in the coal mines of the United States in 1933; if the 1.059 gas and dust fatality rate of the 1900-10 period had been in effect in 1933, about 400 persons world have been killed. Unquestionably, the various teachings of the U.S. Bureau of Mines looking to the avoidance of explosions and fires in mines have had a vital influence in reducing the number of explosions and fires and also in decreasing their destruction in case they occur.

Jan 1, 1934

By S. R. Rannels, D. E. Rannels

"I. IntroductionThe alveolar surface of the lung is covered by two populations of pneumocytes, type I and type II epithelium. The type I cell, which accounts for most of the alveolar surface area and provides a highly specialized barrier for gas exchange (Rannels et al., 1991), is poorly understood. Although approaches to type I cell purification have been discussed, they have not been applied widely because of the lack of phenotypic markers to monitor isolation procedures (Dobbs et al., 1988; Danto et al., 1992). In contrast, the type II cell has been studied extensively, largely because of the development of reliable procedures for its isolation and primary culture. Investigations based on the use of purified populations of cultured type II cells have provided convincing evidence to support a role for the pneumocytes both in the maintenance of normal lung function and in the response of the lung to injury (for review, see Rannels and Rannels, 1989).While type II cells can be isolated by a variety of approaches, the protocols used most commonly are modifications of the gradient method of Dobbs and Mason (1979) or of the panning method of Dobbs et al. (1986). Purification of the cells based on density gradient centrifugation is reliable and consistent, with yields of 30 to 40 X 106 type II cells per rat of 230 g body weight. Isolation procedures applied to a minimum of three to four rats provide the best results, as lower cell yields are common with the use of fewer animals. The protocol below is designed to obtain a maximal cell yield from the lungs of six rats.II. Materials and InstrumentationMaterialsCalbiochem: DNase I (Cat. No. 260912); Corning: culture flask, 75 cm2 #25115; Costar: culture plate, 24-well #3424; disposable serological pipette #4101; Elastin Products Inc: elastase #E-134; Falcon: cellulose nitrate membrane filter, 0.22 µm, #7105; conical tube, 50 ml, #2070; culture dish, 100 mm, #3003; culture plate, sixwell, #3046; Fisher: BaS04 , #B68-500; NaCl, #5271-3; NaHC03 , #5233-50; Fort Dodge Laboratories: pentobarbital, #1206-lE; Gibco: Dulbecco's minimal essential medium (DMEM), #430-1600EC; Hanks' balanced salt solution (HBSS), #310- 4185AG; Joklik's modified Eagle's medium (JMEM), #410-2300EC; HyClone Laboratories Inc: fetal calf serum (FCS ), # A-1115-L; I CN Biochemicals (Flow Labora tories): amphotericin B, #16-723-48; newborn calf serum (NCS), #29-121-54; try pan blue, # 19 5 5 32; Na/gene: Erlenmeyer flask, # 100-4116C; Pharmacia: Percoll, #17-0891-01; density marker beads, #17-0549-01; Sigma: gentam1cm sulfate, #G3632; penicillin/streptomycin, #P3539; trypsin inhibitor, #T9128; Tetko: HC- 160 nylon mesh, #3-160-53."

Dec 1, 1995

By A. L. Murray

First -aid training as an adjunct to safety is receiving more wide spread recognition in the industries every year . Moreover , the adoption of a program for giving firstaid training to practically all employees at a mine or plant is based upon the experience gained and good results obtained from standard first -aid instruction during the past two decades . In the near future industries that desire to maintain a low accident rate , to decrease compensation costs , to reduce lost time , and to build up an efficient , loyal working force , will recognize that training in first aid is one way of attaining these results with little expenditure of time and effort . Progressive organizations will require every man from the superintendent down to take first - aid training and not , as heretofore , only a small percentage of the working force . When employees learn that first - aid training can be applied not only at their daily tasks but in their homes and on tthhee highways ,, they will welcome the opportunity of learning how to care for injuries and perhaps save lives . In a limited way first - aid instruction was given to miners as early as 1899 . Later , in 1904 , a few of the companies in the Pennsylvania anthracite district inaugurated the distribution of first - aid packets to their employees and instructed them in the use of the contents . It remained , however , for a branch of the United States Government to grasp the real significance of widespread first - aid training as an effective means of saving life and minimizing suffering from the large number of accidents among workers in the mineral industries . The United States , owing to its vast resources , both natural and human , for

Jan 1, 1930

By Peter G. Kovalchik, Rudy J. Matetic, Susan B. Bealko, Adam K. Smith

Overexposure to noise remains a widespread and serious health hazard in the U.S. service providing and goods producing industries. Excessive noise can lead to poor verbal communication and reduce the ability to recognize warning signals. These dangerous work conditions can also cause stress and fatigue. Occupational hearing loss is a permanent illness, with no recovery currently possible. Method: National Institute for Occupational Safety and Health (NIOSH) has recognized Noise Induced Hearing Loss (NIHL) as one of the ten leading work related diseases and injuries in the United States, and has emphasized its importance as one of the critical areas expressed in the National Occupational Research Agenda. Results: One of the most serious noise problems in the goods producing industries is the operation of continuous mining machines during underground coal mining. In order to minimize occupational hearing loss, noise hazards are “designed out” early in the design process. NIOSH is leading a national initiative called Prevention through Design (PTD) to promote this concept. This paper describes the quiet by design approach of a noise control that reduced noise exposures of continuous mining machine operators by 3dB(A) using the four functional areas of PTD, namely Practice, Policy, Research, and Education.

By Robert Louis Adams

A general discussion of the structure of the junk automobile recycling system shows that the generation of stripped automobile hulks and scrapped automobiles is price inelastic. As a result, it is extremely difficult for the price mechanism to automatically achieve an equilibrium that will prevent the accumulation of excessive automobile wrecker inventories and vehicle abandonment by the last owners of scrapped cars. The new shredder processing technology and the new portable flattener technology have altered the structure of the junk automobile recycling system. The shredder technology has increased the demand for processed automobile scrap. This increased demand is reflected in higher prices paid for hulks by scrap processors. The portable flattener has reduced the transportation cost of shipping hulks to processors. The two new technologies have eliminated, at least potentially, the net cost of shipping stripped hulks so frequently incurred by wreckers in the past. The elimination of this cost eliminates the economic incentive for excessive wrecker inventories. Unfortunately, the incentive for last owners to abandon their cars does not appear to have been eliminated by the new technologies. The last owner of an automobile with no spare parts value is still likely to incur a cost by delivering his automobile to the recycling system. Although a subsidy payment is probably unnecessary to reduce excessive wrecker inventories, such a payment might be one solution to the problem of automobile abandonment. However, there are a wide variety of subsidy programs that could be introduced. Before any Federal subsidy program is introduced to reduce automobile abandonment, it is recommended that the program be tested on a limited basis in many different parts of the country.

Jan 1, 1973

By Bruce D. Sartwell

A program was written which utilizes a remote teletype input to a time- sharing computer to plot charged particle or X-ray energy spectra which are stored in the memory of multichannel analyzers. The program, written in FORTRAN V, accepts the data printed out by the pulse height analyzer on paper tape and then, after reading these data tapes into the computer, plots on the teletype the desired energy spectra on a scale automatically adjusted for the maximum number occurring in the data. The program is flexible enough so that the researcher can subsequently expand or contract the vertical (intensity) or horizontal (energy) scales. With a slight modification, the program will accept data printouts from scalers or analog to digital converters. The program also includes a feature for integrating the energy peaks obtained by pulse height analysis.

Jan 1, 1970

By Bureau of Mines Staff

Coal research and related activities in 1964 by the Bureau of Mines resulted in many advances in the production, preparation, and utilization of this valuable natural resource. Mining research during the year was marked by work on hydraulic mining, coalbed degasification, mine drainage control, mine sealing, strip-mine rehabilitation, and quenching of mine-refuse fires. Bureau research continued to produce information leading to increased safety in underground mining. Such research included roof and rib control via bolting and bonding, pressure monitoring of coal and mine rock during mining operations, and development of safety devices for detecting conditions leading to roof falls. Other safety work was continued on methane detectors, coal-dust suppression, and mine venti lation equipment and techniques. Mine explosion and explosives research, mine equipment and materials, safety rule modernization, and safety education and training of mine workmen were continued. Coal storage and preparation work in 1964 ranged from freezeproofing of lignite for rail shipment, through washability studies of coals and washing equipment, to research on new ways to remove ash and sulfur from coal. Electric power production, which ,accounts for a major portion of the market for coal, received further study. Unique power generation systems, inc luding coal-burning gas turbine and megnetohydrodynamic generators, were intensively investigated. Conventional power systems were improved through continuation of work on furnace performance, powerplant stack gas purification, and engineering and boiler water service.

Jun 1, 1965

By William L. Crentz

This Investigation of the preparation characteristics of the coals in Armstrong County, Pa., is the third in a series of Bureau publications by counties appraising the practicability of upgrading marginal deposits to metallurgical standards. Earlier investigations covered the washing characteristics of the coals occurring in Cambria County, and the principal reserves remaining in Indiana County. In Armstrong County, the Upper Freeport bed is the major source of production, the Lower Kittanning bed being of secondary importance. The Lower Freeport bed is mined to some degree, but it is usually too thin and spotty in occurrence to support large-scale operations. The remaining production is taken from the Pittsburgh, Middle Kittanning, and Upper Kittanning beds, but the quantities are insignificant. Table 1 shows the county&apos;s coal production) by beds, during 1948. The coals of Armstrong County are not generally considered to be of metallurgical quality because of the high sulfur content. The raw coals usually analyze more than 2 percent sulfur, and more than 4 percent sulfur is not uncommon, especially in the Lower Kittanning bed.

Jan 1, 1951

By R. M. Santmyers

Umber and sienna, like ocher, are naturally occurring mineral pig- ments composed largely of clay permeated with hydrated iron (ferric oxide), but they differ from ocher in that they also contain hydrated manganese oxide. The presence of manganese accounts for their browner color. In addition to silica and alumina (clay) and the coloring oxides of iron and manganese, these pigments often contain lime, barium, and other metallic salts as impurities. Sienna most nearly approaches ocher in chemical composition, and the chief distinction is its physical character. It grades into ocher with de- creasing iron content and into umber with increasing manganese content. Sienna is translucent rather than opaque and is more of a stain than a pigment; as the iron oxide content is rather high (often 60 to 80 per cent), the color is strong and rich and varies from pure brown to reddish brown. This pigment raw sienna, terra di Siena, and Italian earth. is known under several names: Burnt sienna is a pigment of an orange-brown tint made by cautionsly calcining raw sienna. It is divided into two grades; American, and Italian burnt sienna. American burnt sienna is a reddish-brown pigment containing from 25 to 60 per cent iron oxide (Fe2O3). One grade, found in Pennsylvania, analyses as high as 80 per cent and is mown as double strength sienna. Italian burnt sienna is a pigment generally containing more iron than the American product, averaging 60 to 75 per cent iron oxide.3 American pig- ments of the same iron content differ materially in shade, having a Havana- brown color, whereas the Italian is more of a maroon. Italian siennas when tinted with 20 per cent of white, show a bluish tint, whereas American siennas yield a brownish or yellowish hue. Raw umber, also known as Turkey umber, Levant umber, and terra ombra, is a greenish to yellowish brown siliceous and ferruginous earth, containing a considerable proportion of one or other of the higher oxides of manganese, Mng04 and MnO2." It is similar in many respects to raw sienna except that it is much coarser and contains more manganese oxide. All umbers contain over 5 per cent of manganese dioxide. Like sienna, umber is a permanent pigment, not being injured by light or by impure atmospheres. Burnt umber (velvet brown, chestnut brown, etc.), results from the calcination of raw umber. The color is much richer and warmer than that of the raw umber. The colors are equally permanent and can be used in conjunc- tion with all other durable pigments.

Sep 1, 1931

By W. H. Eddy

The Bureau of Mines conducted laboratory batch-and small-scale continuous flotation processing tests on waste granite fines from Georgia, to determine the feasibility of recovering usable feldspar and quartz products by flotation. Two flotation methods were utilized for the removal of biotite and other iron-bearing minerals: One was in an acid-cationic circuit, and the other in an alkaline-anionic-cationic circuit. Feldspar was recovered using an acid-cationic method. To produce commercial-grade feldspar and quartz products it was necessary to employ either two sequential froth flotation circuits or one froth flotation circuit supplemented by wet-magnetic separation techniques to remove iron contaminants. Continuous flotation processing yielded a commercial-grade feldspar concentrate containing, in percent, 3.8 Na20, 5.4 K20, and 1.10 CaO, with recoveries of 77.8, 70.3, and 64.4, respectively. The feldspar tailing was high-quality glass sand containing 98.2 percent SiO2 and 0.024 percent Fe2O3. About 42 percent of the quartz was recovered at glass sand specifications. An effective separation of, potash feldspar from the bulk feldspar concentrate was achieved by batch flotation in a mineral separation cell.

Jan 1, 1974

By S. A. N. Sheya

Many gold-bearing ores in the Western United States also contain small amounts of mercury. The presence of mercury creates potential pollution and health hazards during several steps in gold processing. An investigation was undertaken by the Bureau of Mines to develop techniques for removing mercury from cyanide mill solutions by selective electrowinning to reduce the potential hazards. Sixty-five percent of the mercury was selectively electrowon from synthetic carbon strip solution at applied potentials of 1.00 to 1.50 V when using a mercury-coated platinum or copper plate cathode. Increasing the active surface area by using mercury-coated copper wool resulted in up to % pct of the mercury being electrowon from mill carbon strip solutions that contained 1.9 to 20 ppm Hg, 20 to 345 ppm Au, and 0.35 to 39.5 ppm Ag. About 98 pct of the silver was electrowon with the mercury onto the mercury cathode. Gold extraction ranged between 0 and 20 pet. Results of the investigation showed that choice of cathode material was critical to the success of the process. Selectivity was not achieved using uncoated steel wool cathodes.

Jan 1, 1988

By J. B. Clemmer

Fluorspar is one of the most important nonmetallic minerals and is used extensively in the metallurgical, ceramic, cement, and chemical industries. The steel industry consumes most of it, but as the Mineral is the chief source of fluorine, it is becoming increasingly valuable to the chemical industry in the production of fluorine compounds. The development of nontoxic organic fluorides for use as refrigerants in mechanical refrigeration and air-conditioning units illustrates the increasing use of fluorspar in the chemical industry. Most domestic flurospar comes from deposits in the Illinois-Kentucky district, which centers around Rosiclare, Ill. About a dozen companies operate in the district, which comprises parts of Pope and Hardin Counties in southern Illinois and Crittenden, Livingston, and Caldrell Counties in western Kentucky. According to the latest available statistics, this district supplied 165,960 short tons of fluorspar in 1937, compared with the total domestic production of 151,230 tons. Imports totaled 37,063 tons.

Jan 1, 1939

By Frank J. Wiebelt

Under a general program to extend the resources of mineral deposits, the Bureau of Mines examined the Quien Sabe antimony mine in October 1948. The preliminary evaluation demonstrated that a diamond-drill program was warranted co establish the tenor and persistence of the veins and permit an estimation of antimony reserves. The Bureau of Mines conducted a diamond-drilling program on the property from December 1949 to May 1950. Ten holes aggregating 2,483 feet were drilled. Nine of the holes encountered antimony-bearing vein material.

Jan 1, 1956

By George A. Morrison

This paper describing the methods of mining and crushing limestone at the West Winfield, Pa., limestone mine of the West Penn Cement Co., is one of a series being prepared by the Bureau of Mines on mining practices, methods, and coats in the various nonmetallic mining districts. HISTORY The limestone deposits of western Pennsylvania have been exploited for many years and have been quarried extensively at West Winfield in Winfield. Township, which lies in the southeastern corner of Butler County.

Jan 1, 1931

By W. D. Haselton

This paper dealing with the mining methods used in producing iron ore from an underground operation located in the central-western part of the Mesabi Range in Minnesota is one of a series being prepared by the Bureau of Mines on mining practices, methods, and costs in the various mining districts in the United States. The mine here discussed was laid out in accordance with a plan adapted to a rather unusual type of ore body, the nature of which is such that the mining method necessarily differs in certain respects from the method used at most of the mines in this district. A description of it may therefore be of interest.

Jan 1, 1930

By A. Brown

This report details work performed and results obtained in a study of the water management aspects of oil shale mining and retorting in the Piceance Creek Basin. Three specific sites were investigated, and optimal water management systems for both conventional and in-situ extraction processes were generated. Water-related legal and environmental constraints on development were identified and the water management schemes were developed in compliance with these regulations. Limitations on shale oil production implied by limited water supplies were evaluated. Potential Basin-wide effects of development were evaluated using a computer model, and mitigation strategies were developed. Recommendations for additional investigation and analyses were presented.

Jan 1, 1977

By Jueun Lee, Jong-Hwa Yoon, K. Rider, Bernard J. Martin

Whole body vibration is known to affect movement accuracy [1], however little is known about changes in the organization of movement and movement strategies used to limit the influences of perturbations. The specific aim of this work is to analyze the motion and coordination of upper body segments of seated operators performing reaching tasks under whole-body sinusoidal vibration exposure and simulated vehicle ride motion. The long-term objective is to model reach coordination and predict the dynamic behavior of the upper body motion under vehicle vibration exposure. Method The reach task consisted of pointing with the right hand index finger to targets located on touch screens placed in front of the subject, 45° overhead and 90° to the right in the mockup cabin of an HMMWV placed on a 6 DOF ride motion simulator. The task was performed under stable (no vibration) and vibration (sinusoidal vibration or simulated ride motion) conditions. A motion capture system was used to record kinematic data of reflective markers to recreate body link trajectories. Joint angles (torso, shoulder and elbow; Figure 1) were then computed using quaternions. Coordination between body links was defined as a) the joints angle-versus-angle relationships between the upper arm and lower arm, and b) the joint motion onset relationships between torso, upper arm and lower arm in the time domain. Results Angle–versus-angle relationships. The relationship between upper arm vs. lower arm angle and torso vs. upper arm angle for a far forward reaching movement in the stable (solid lines) and vibration conditions (dotted lines) are illustrated in Figure 2. Fig 2A compares the control condition with a 4 Hz lateral vibration while Fig 2B compares the control condition with a 6 Hz vertical vibration. It appears that under vibration exposure the reduced upper arm extension is compensated by an increase in torso flexion. This effect is seen in the last phase of the movements (encircled areas). In addition, the lower arm extension is delayed under 6 Hz vertical vibration (Fig 2B left panel). Time of joint motion onset. The timing relationship between torso, upper arm and lower arm is largely a function of the target to be reached. Examples of delays between body links are illustrated in Figure 3. The control condition is compared to a 6 Hz vertical vibration for three

Jan 6, 2006

By Thomas Gales

Longwall mining of thin shallow coal seams utilizing open pits is technically feasible. The thinnest coal seam which can be mined using available technology is 34 inches. The capital expenditure for a 1,000,000 ton per year operation is $15,494,000, and the projected rate of return is 5 percent. Similar statistics for a conventional area surface mine are S18,937,000 capital and 14 percent rate of return. The longwall surface mining method disturbs 63 acres of land per 1,000,000 tons, and the conventional area surface mine disturbs 198 acres A significant bibliography of the technology involved is included.

Jan 1, 1976