Search Documents

By Marc Ruest, Lewis Martin

A new instrumented cable bolt has been developed by the National Institute for Occupational Safety and Health at the Spokane Research Laboratory in Spokane, WA. Although various instruments are available to measure load distribution and magnitude along a grouted cable, this instrument is innovative in that it uses strain gauges internal to the cable as load-measuring sensors. The instrument has been successfully tested in the field at FMC’s Granger Mine, Meikle Mine, and Getchell Mine. A “split-pipe” laboratory pull test was performed on each of three cable bolts instrumented with the new device. Each test consisted of grouting a 1.83-m-long cable in two 0.91-m-long sections of schedule 80 pipe. A numerical analysis was then performed in which laboratory boundary conditions were simulated and model properties derived from textbook guidelines. The loads calculated by the model were then compared to the measured loads.

By Terry G. Montgomery, Eric S. Weiss, John E. Going, Kenneth L. Cashdollar

The Pittsburgh Research Laboratory (PRL) of the National Institute for Occupational Safety and Health (NIOSH) and the Mine Safety and Health Administration (MSHA) conducted joint research on dust explosions by studying post-explosion dust samples. The samples were collected after full-scale explosions at the PRL Lake Lynn Experimental Mine (LLEM), and after laboratory explosions in the PRL 20-L chamber and the Fike I m3 chamber. The dusts studied included both high- and low-volatile bituminous coals. Low temperature ashing for 24 h at 515 °C was used to measure the incombustible content of the dust before and after the explosions. The data showed that the post-explosion incombustible content was always as high as, or higher than the initial incombustible content. The MSHA alcohol coking test was used to determine the amount of coked dust in the post-explosion samples. The results showed that almost all coal dust that was suspended within the explosion flame produced significant amounts of coke. Measurements of floor dust concentrations after LLEM explosions were compared with the initial dust loadings to determine the transport distance of dust during an explosion. All these data will be useful in future forensic investigations of accidental dust explosions in coal mines, or elsewhere.

By Masami Hayashi

Cost evaluations were made for five processes for producing 100,000 tons of electrorefined copper per year from a chalcopyrite concentrate. The processes were (1) conventional smelting with all furnace gases vented to the atmosphere; (2) conventional smelting with converter gases routed to an acid plant and reverberatory gases vented to the atmosphere; (3) conventional smelting with converter gases routed to an acid plant and reverberatory gases to a citrate system plant; (4) conventional smelting with all furnace gases routed to a citrate system plant; and (5) a modified smelting process in which the concentrate is roasted before being charged to the reverberatory furnace, with roaster and converter gases routed to an acid plant. The total fixed capital costs of the plants were estimated as (1) $56.7 million, (2) $77.4 million, (3) $87.2 million, (4) $73.9 million, and (5) $77.0 million, respectively. Total S02 removal from stack gases as sulfuric acid or sulfur for each process was (1) none, (2) 66 percent, (3) 99 percent, (4) 98 percent, and (5) 78 percent. Assuming no credit for byproduct sulfur or sulfuric acid, total operating costs per pound of electro-refined copper produced were estimated as (1) $0.081, (2) $0.103, (3) $0.119, (4) $0.111, and (5) $0.103, respectively.

Jan 1, 1974

By Joan C. Biordi

[Composition profiles for atomic, radical, and stable species, as well as temperature and area expansion ratio profiles, have been determined for a nearly stoichiometric CH4-02-Ar flame and one to which 0.3 percent CF5Br inhibitor had been added. Net reaction rate profiles were calculated for all the observed species. For the normal flame, these and the mole fraction profiles gave rate coefficient information about the elementary reactions in the methane flame, for example, CH. + 0 4- H2CO 0 H, k4 = 1.05 X 1014CM3 mole-1sec-1 for 1,550§T 0,725' K; CO + OH 4 C02 + H, k6= 4.7 X 1011 for 1,350{T X1,750° K. Comparison between the inhibited and normal flame showed that A] and [CH3] were significantly reduced at the lower temperatures in the inhibited flame even though in the hot gas region the [E] [OH!, and [0] were essentially the same in both flames. The CF3Br disappears very early in the flame, relative to the fuel, and the reaction primarily responsible for its disappearance is H v CF3Br 4 HBr + CF3, where k7 is found to be 2.2 X 1014 exp(-9460/RT) for 700-1,550° K. Reaction of the inhibitor with methyl radicals provides for the relatively small amounts of CH3Br observed, but CH3 + Br2 - CHs Br + Br must also occur. The HBr formed reacts rapidly with H atoms to form H2 and Br, but the reaction is soon "balanced" in the flame as may be demonstrated by calculation of the equilibrium constant at various temperatures. The fluoro-carbon fragment produced in reaction (7) also reacts rapidly, in part with methyl radicals to give the observed elimination product CH2CF2 Later in the flame, above -1,400' K, F2CO is formed from the reaction CH2CF2 + 0 P F2CO + CH2 and k., -1.5 X 1013 at 1,600° K. The rather slow decay of carbonyl fluoride is attributed to reaction with H atoms according to the sequence F2CO I H - HF + FCO and FCO + H HF + CO.]

Jan 1, 1975

By F. S. Crawford

"After many years of safety activity in the United States in one form or another it becomes increasingly evident to those in contact with safety work that to achieve continuous good results in accident prevention there must be an aggressive organization behind the safety movement at each mine with fairly definite plan and policy. A study of the methods used by various companies and the results they have attained will be of value to the common cause of safety promotion.A study has been made of the safety records of the Menominee iron range in the Lake Superior district, and of data from the county mine inspector's report. Several companies on this iron range that have attained a certain measure of success in their work of accident prevention have given data, and a summary of their safety methods is presented.The Menominee iron range of Michigan lies in the southern portion of the upper peninsula of Michigan, bordering on Wisconsin. It consists of two main. divisions--the West Menominee Range, situated in Iron County in the vicinity of Iron River and Crystal Palls, and the East Menominee range situated in Dickinson County in the neighborhood or iron Mountain, Mich. The mines about Iron River and Crystal Falls are peculiarly subject to fires in a carbonaceous, sulphur-bearing black slate which appears in the footwall. This gives considerable trouble because fires in this material start from spontaneous heating. The methods of mining are top slicing and open stoping, working on benches along the sides of the stopes. The character of the ground varies from medium Soft ore to relatively hard ore which permits open stoping. Approximately one-third of the operating mines are equipped with a fan for main mechanical ventilation. The remainder are ventilated by natural draft. The East Menominee range is the older, top slicing having been used there for a number of years, and the timber mats have boon well developed. In common with all districts, some companies pay more attention to safety than others, although, those which do riot have the best records do pay some attention to safety.During the past three years the annual production per man employed has remained about constant, but in many mines a general decrease is shown in the accident record. The variation in the results attained can be ascribed mainly to the earnestness with which accident-prevention work is pursued, essentially regardless of the method of mining used. This is shown to be generally true, because the record indicates a steady decrease in one mine with an active safety department, while in adjoining mines with the same kind of ground and method of mining but where not such intensive attention has been paid to safety work, the accident record is high."

Oct 1, 1931

By Stanton L. Tainter

"INTRODUCTION Molybdenite, the only common mineral and ore of molybdenum, occurs wide¬-spread but is concentrated as the main ore mineral in commercial quantities in only a few known deposits. Consequently, the Government sought additional sources of the minerals as a precaution against the possible shortage of moylbdenm for war uses. Upon request by the War Production Board, the New Year’s Eve and Esperanza properties of the Amargosa Molybdenum & Copper Corp. were investigated by the Geological Survey 3/ and the bureau of Mines 4/. The Survey appraised the mineral potentialities of the deposit and prepared topographic and geologic maps, and the Bureau made a preliminary engineering examination. The deposits were previously examined by W. J. Vanderwilt, consulting engineer. It was largely due to his recommendations that interest was stimulated in the deposits.Development on the New Year’s Eve deposit indicated a small tonnage of sub marginal ore. There was little development at the Esperanza, but surface examination revealed a large volume of rock containing a little molybdenite and a trace of copper in the oxidized outcrops. Some molybdic oxide was noted suggesting that some molybdenite might have been leached from the oxidized outcrops and that the molybdenite content in the sulfide zone might be higher."

Feb 1, 1947

By Todd M. Ruff

An average of 13 mine workers are killed each year by being run over or pinned by mobile mining equipment. At surface mines, these accidents commonly involve large dump trucks that drive over a smaller vehicle or a person that is in the dump truck’s blind spot. One method of detecting a person or another vehicle in a blind spot is to use some type of sensor technology such as radar or radio-frequency identification (RFID). Researchers at the Spokane Research Laboratory of the National Institute for Occupational Safety and Health tested a number of commercially available and experimental sensors that monitor obstacles in a vehicle’s blind spots. None of the sensors had been previously applied to the specific problem of rigid-frame surface mining trucks. This report documents the procedures and results of tests conducted after RFID and radar systems were mounted on a 50-ton-capacity dump truck. It was determined that both RFID and radar technology show promise for detecting obstacles in the blind spots of mining equipment; however, more development work is needed to meet the unique requirements of mining equipment and the mine environment.

Jan 1, 2000

By John P. Shubilla1, Nicholas Kyriazi

A joint effort by the Pittsburgh Research Center (PRC) and the Mine Safety and Health Administration (MSHA)3was undertaken to determine how well self-contained self-rescuers (SCSR's), deployed in accordance with Federal regulations (30 CFR 75.1714), held up in the underground environment with regard to both physical damage and aging. This report presents findings regarding laboratory-tested SCSR's in the fifth phase of testing from mid-1993to early 1996. The SCSR's were tested on human subjects and on a breathing and metabolic simulator (BMS) at PRC. These results indicate that most of the apparatus, if they pass their inspection criteria, perform satisfactorily.

Jan 4, 1996

By Shih-Chi Chang

[An exploratory research is done on untreated coal 1v- using&apos; x-ray crnctinn techniques. Comparison is made on diffraction data before And pct Pr n-tiAne is pressurized (n the coal samples. Although, only ? qualificative -1; t s obtained, the FoIIowing Statement r :&apos; n untreated teal seem- There are other materials in cost. They are accumilated in !e ,r rc r, cin? the microseoric layered structure of coal. 7"P partial graph r :r a&apos; o., «&apos; the i&apos;pr1 cart o ! in cna1 assumes varclor, r,rie&apos;,r: r in&apos;is. R nr ?-&apos;c,.r1&apos;ed I n coal is helm ;n the micrornre s&apos;??ste^ o&apos; c, .:l an&apos; t rr i, ,o <.~i:&apos;epee of Ion(4inc to carton h« x-ray tit If raction me.:SUr&apos;rientq. :t?e me r &apos; nP in r^icropores assumes no structure themselves at room tempera¬FLre. ;inally, some of the other materials in coal are in the form of }vrlrited crystallites and they have anisotropic pro&apos;th hnt&apos;1? in the lavers.]

Jan 1, 2012

This Bureau of Mines publication presents an overview of mine electrical power systems research currently being conducted by the Bureau. The papers, given at a Technology Transfer Seminar, emphasize the increasing importance of research related to the safety considerations of underground coal mine electrical systems. Selected topics are included that summarize results of research in the areas of electrical shock prevention, explosion-proof enclosures and load centers, discriminating circuit breakers, and trailing cables. Other topics discussed at the seminar are published as separate sections of the Bureau of Mines Hand- book "Application Notes--Mine Electrical Power Systems."

Jan 1, 1982

By D. A. Elkins

Design plans and detailed cost estimates of mining and treating ore from Maggie Canyon deposit by two alternative methods which can be used in the event of a sudden need to exploit this resource are given . Lower costs are estimated for the operation employing oil - emulsion flotation . The total capital investment required for this operation is estimated at $ 11,750,000 . Assuming an 85 percent recovery in mining , 55.6 pct of the manganese in the ore reserve would report in 153,333 tons of ferromanganese containing 75 pct manganese . The production cost for the 5 - year operation would be about $ 245 per ton of ferromanganese . The total annual operating cost would be approximately $ 7.5 million , distributed , in pct , as follows : Mining 11.9 , milling 24.4 , sintering 9.9 , smelting 47.2 , hauling ore and sinter 2.8 , and general offices 3.8 . Recovery and costs are both higher for the operation employing dithionate leaching . In this operation the required investment is about $ 17,220,000 . Manganese recovery would be 67.6 pct in 186,160 tons of ferromanganese . Production cost would be about $ 284 per ton of ferromanganese . The total annual operating cost would be about $ 10,575,000 , distributed , in pct , as follows : Mining 8.4 , milling 44.4 , sintering 7.4 , smelting 34.7 , hauling ore and sinter 1.3 , and general offices 3.8 . Potential process modifications might reduce the operating cost of the first operation by as much as 7 pct and that of the second operation by as much as 9.5 pct , but exploitation of the deposit by the techniques studied is not economical today .

Jan 1, 1964

By F. Fraas, J. E. Conley

"The problem of recovering potash from the mineral polyhalite (K2SO4.MgSO4.2CaSO4.2H2O), occurring in large quantities in the salt beds of Texas and New Mexico, has been under investigation at the Nonmetallic Minerals Experiment Station of the U. S. Bureau of Mines continuously since 1928. Most of the results previously obtained have been published in technical journals and in a series of Bureau of Mines Reports of Investigations.The experiments described in the present report were performed to ascertain whether a continuous countercurrent extraction of calcined polyhalite by hot water would yield satisfactory recoveries and concentrations of sium sulphate in the top liquor. Previous investigation by Storch 4 had shown that the rate of solution of uncalcined polyhalite was too slow to be of value in an industrial process, and Storch and Clarke 5 had demonstrated that calcination of the polyhalite greatly, accelerated the rate of solution in hot water, allowing most of the potassium sulphate to be readily extracted."

Sep 1, 1933

By Winton J. Gale

Coal pillar design has been based on generalized formulas of the strength of the coal in a pillar and experience in localized situations. Stress measurements above and in coal pillars indicate that the actual strength and deformation of pillars vary much more than predicted by formulas. This variation is due to failure of strata surrounding coal. The pillar strength and deformation of the adjacent roadways is a function of failure in the coal and the strata about the coal. When the pillar is viewed as a system in which failure also occurs inthe strata rather than the coal only, the wide range of pillar strength characteristics found in the United Kingdom, United States, Republic of South Africa, Australia, People&apos;s Republic of China, Japan, and other countries are simply variations due to different strata-coal combinations, not different coal strengths. This paper presents the measured range of pillar strength characteristics and explains the reasons. Methods to design pillar layouts with regard to the potential strength variations due to the strata strength characteristics surrounding the seam are also presented.

Jan 5, 1999

Most laboratory sealant studies were carried out in 2.0 inch I.D. Plexiglas tubes of 9.0 inches height containing 4.0 to 4.5 inches reconstructed soil from an 0-8 or 8-16 inch soil horizon at the Lanse site. (When soil was used from the Kato site, the top soil horizon was approximately 0-4 inches. The 4-8 inch horizon was somewhat comparable to the Lanse 8-16 inch horizon.) A 20 mesh Saran or steel screen was placed over the rubber stopper with a bottom drain to a 100 ml measuring cylinder. In some earlier experiments a 1/2 inch bed of 1/4 inch pea-gravel was then added, but in later experiments this was eliminated as it showed no particular utility. Field soil samples collected by a shovel were stored in sealed containers and sieved through a 4 mesh screen just before use. (Moisture content was typically about 25% for A horizon soil and about 20% for B horizon soil.) The sieved soil minus roots was then added in increments of about 1 1/4 inches. Compaction was effected by dropping a weighted ramrod (1-7/8 inches O.D,) five times from a height of two inches. If about twenty tamps were used or if the soil columns were rapped vigorously while water-logged, compaction was high with no detectable percolation. Freezing such samples would then usually cause very slow percolation, e.g. 1-2 ml/day. Using this as a standard procedure, percolation flows were usually stablized after two to three days to rates of about 100 to 200 ml/hour. Percolate was recycled carefully to minimize disturbance of the soil surface. When percolation flows were about 100 to 200 ml/hour, various additives (sealants) were introduced to the moist column in two to three increments to maintain a slight head. Additive concentrations were usually 2-1/2% with some at 5% in earlier experiments. Typical use of 40 ml of 2-1/2% additive corresponds to 4400 lbs/acre. When no more additive was present as supernatent liquid, water washes of about 15 ml were then used several times followed by special additives as needed. More water washes were then used to maintain a head of about 1/2 inch. Percolate was collected in 100 ml cylinders to measure percolation rates in ml/hr. Turbid percolate was evaporated to determine amount of eluted latex. Percolate was sometimes checked for pH by Pan-pH Indicator Paper9,10 reading in 0.5 units. Surface tension measurements were sometimes made by a DuNouy tensiometer10 in experiments using a surfactant for pretreatment.

Jan 1, 1972

By Horst Peter Wölfel

The goal of biodynamic models is to simulate the vibration behaviour of the human body. In combination with experimental studies biodynamical models can be a powerful tool for the analysis of the effects of vibration exposure on health [1] and comfort. This paper gives an overview of the state of the art of biodynamic whole-body vibration models of humans, addressing both numerical models and hardware dummies. Method Two approaches are distinguished, the phenomenological and the anatomical, as illustrated in Figure 1. [ ] Phenomenological models aim to reproduce the vibration behaviour of humans with respect to particular physical quantities, chiefly the driving-point impedance at the interface to the seat, and partly with respect to other transfer functions. Discrete systems of masses, springs, and dampers with several degrees of freedom whose topology and parameters are determined by structure- and parameter identification methods are used in the sense that the functions derived from measurements are reproduced as well as possible. This paper provides an evaluation of this methodology and defines its range of application as well as its limits.

Jan 6, 2006

By A. T. Iannacchione

Underground limestone mines typically use the room-and-pillar method of mining in the generally flat-lying limestone formations. In some cases the dip may exceed 5° which can result in unique roof instability problems. Stability may be further exacerbated by the presence of horizontal tectonic stresses. Field studies and numerical model analyses are combined to assess the affect of the dip in various stress conditions. The results showed that where the horizontal tectonic stresses are sufficient to cause intact rock failure, increasing dip results in increased failure potential. The effect of the dip is greater when the maximum horizontal stress is parallel to the dip. Two case studies are presented and evaluated against the findings of stress analysis results. The study showed that the empirical rules of orienting headings parallel to the maximum stress are generally applicable to dipping excavations, except when mining in the up-dip direction. The importance of accurately determining the orientation of the maximum horizontal stress is emphasized because the window of favorable orientations relative to the stress is small.

By G. St. J. Perrott, N. A. Tolch

"The measured strength of an explosive depends to a certain extent on which it is determined. An earlier investigation showed the relative propulsive strength of dynamites as determined in one type of apparatus, ballistic pendulum.4 The aim of this paper is to precept strength data on these same dynamites determined in another type of apparatus, the Trauzl lead block, and to compare the results with those of the ballistic pendulum. Trauzl lead block have been in use many years for the determination of thy strength of explosives, under moderate confinement.5 The common practice is to shoot 10 grams of explosive, in tinfoil wrapper,- and then to measure the volume of the cavity produced by the shot. The volume of the original borehole is deducted from the gross expansion and sometimes a correction is made for the expansion produced by the detonator. Dry sand is used for stemming the charge.It has been found that the expansion in Trauzl blocks is not strictly proportional to the charge. Naoum5 believed that for scientific accuracy the charge should undoubtedly be regulated to give the same average expansion for each sample tested, but for expansions of 200 to 400 cubic, centimeters the deviation from proportionality is not sufficient to give results appreciably in error.Neubner7 found that the proportionality curve is tangent to the charge-expansion curve at about 300 cubic centimeters expansion, provided that no deductions are made for the volume of the original borehole or the effect of the detonator; the total or gross expansion is proportional to the charge between expansions of 250 to 350 cubic centimeters without serious error."

Oct 1, 1930

By W. H. Schiffbauer

NIOSH has developed an active proximity warning system called HASARD (Hazardous Area Signaling and Ranging Device) for warning workers as they approach known dangerous areas around heavy mining equipment and other dangerous work zones. HASARD is composed of a transmitter and a receiver. The transmitter generates a 60-kHz magnetic field using one or more wire loop antennas. Each antenna is adjusted to establish a magnetic field pattern for each hazardous area. The receiver, worn by the worker, is a magnetic field strength meter. The received signal is compared against preset levels which are calibrated to identify levels of danger. The receiver outputs can include visual, audible, and vibratory indicators and it can also be made to disable machine functions. HASARD was field tested on a Joy 12 continuous miner, a Komatsu 210 M Haulpak, and on a highwall launch vehicle. Slight modifications were made for each application. HASARD provided warnings as designed and proved to be rugged enough to withstand the harshest of production environments.

By E. L. Garton

[AnalY3e s of Qany crude t) i 1 s prod.uced in Loui sia.na are incl udeo" in re!Jor~ ~ th&apos;l t have b en u~li shed by the BurOllU 0: i?{ine s. The first rc-port,j} givin..; analyseG of 6 Louisiana crude oils, &apos;-vas pUblluhed in 1921&apos;l.s,nd this was 1&apos;0110\ cd a year later by P.ep rt of InvBstign.tions 21a6t~ givi~ 7 addi tional analyses. The G7even :,ost il&apos;!lportant of these analyses were incol"]lorated in Bulle~in 91,.2, is~ued in 1928. In 1934, analyses of 26 cl ... ude oils j)roduced in southern Louisiana ",ere published ? .§! The present report I)renonts analysos of 72 ad(~itional samples of crude oil frorl 4-, fields in 23 "l)ari shefl in Loui f",io.r]

Jan 1, 1939

By Victor Erickson

ECONOMIC recovery, which began in 1958, carried through into 1959 but was somewhat retarded by the 116-day steel strike beginning in July 1959. Recovery and economic growth increased production and consumption of mineral fuels 3 percent above 1958. The increase was accomplished despite a drop of 26 percent in coal exports. Prices remained constant during the year so that the value of production and consumption also increased 3 percent over 1958. Stocks in the hands of producers at yearend were little changed from the supply at the beginning of the year. Employment in the field of mineral fuels decreased 6.4 percent from 1958. Average hourly earnings were up 7 percent, and average hours worked were up 5 percent, with the result that weekly earnings gained 11.8 percent. Internal freight rates were relatively constant, but ocean tanker rates declined both in 1958 and 1959 from the high rates charged during the Suez crisis. The index of major input expenses decreased for anthracite, held constant for bituminous coal, and increased for petroleum. The index of labor cost per dollar of product and per ton of product declined again in 1959 to a new low in anthracite and bituminous-coal mining industries.

Jan 1, 1960