Search Documents

By Anderson Meireles, Leonardo Soares Chaves, Raul Carretero Hoz, Carlos Eduardo Soares Feliciano, Renato Jacome Costa

The large iron deposits in the northern region of Brazil located in the Amazon Craton have in common the presence of natural cavities. These cavities primarily occur in the upper layer of the ore body, formed above hematite mineralization. Their origin remains a topic of debate, often associated with hydrothermal drainage processes and erosive evolution. Over time, these cavities have become integral to the local environment, each contributing to the regional ecosystem of fauna, flora, and the significance of speleothems found within them. Managing these cavities poses a significant challenge for iron mines in the area. On one hand, they must preserve the cavities from anthropogenic actions, while simultaneously handling heavy equipment and large volumes. In 2023, the development of the mine took place towards the cavity under study, revealing systematic deviations in vibrations recorded during nearby detonations as the blasting got nearer. To address this, a work plan was put in place, emphasizing a straightforward approach: constructing lithology-specific vibration models, defining charge abacuses, and optimizing timing to reduce charge amplification. Implementing this methodology significantly improved adherence to the vibration limit, resulting in an around 50% reduction in standard error. This paper presents the consolidated work that allowed mining activities to continue in the area through controlled blasting, effectively mitigating potential anthropogenic damage in sensitive areas.

Jan 21, 2025

By Doug Wathen, Philip M. E Thomas

The City of Fort Myers needed to replace a 40-year old 42-inch storm sewer line in downtown Fort Myers with a new 54-inch line to accommodate population growth. The old line had to be kept operational while a new line was installed. The contractor spent two months using a drop ball, a hoe ram, and large rippers trying to break the three to four feet of rock that needed to be removed to accmmodate the new pipe. Mechanical trenching was considered but was proven to be overly expensive. On very short notice, Ireco of Florida was asked to design and execute a blasting procedure that would allow this project to proceed. Nearby buildings were over 80 years old, three of them containing antique shops specializing in glass antiquities with attorney offices above them. High water table compounded problem with a 20-year old steel water main and clay drainage pipe 15 feet frcan the new sewer line. Holes had to be drilled within six inches of the edge of the existing pipe to four feet below the pipe on either side of the pipe and blasted. No interruption in the sewer line flow was to be tolerated.

Jan 1, 1996

By Daniel Castelo, Ben Potter

This paper will discuss the most efficient and effective way to use shape charges when considering standoff distances and the amount of an explosive to be used. For each shape charge test that was performed, a one inch diameter copper liner of 90o was used. Different standoffs for each shape charge were tested to see which one would penetrate the deepest into rolled homogenous armor steel (RHC 44). It was determined that a standoff of three cone diameters provides the deepest penetration. In addition to testing for optimal standoff distances, the effects of overfilling as well as under filling a shape charge with explosive was tested against a shape charge with the bare minimum amount of explosive for correct detonation. These “fill” tests were all performed at a standoff of three cone diameters. Overfilling has little to no effect towards penetrating deeper into a target while under filling a shape charge has an effect of shorter penetration. C-4 explosive was the main explosive for all shape charges.

Jan 1, 2011

By Brian Lewis, Reinhold Daykin Schnell

Blasting is the primary and most effective method for breaking and moving material at most mine sites. The blast design is often adjusted in efforts to optimize the effectiveness of the blasts’ explosive energy while minimizing costs. When adjusting blast design parameters, it is important to adjust one parameter at a time, observing and analyzing the potential effects of the change on the overall blast performance.

Feb 6, 2023

By Minoru Kawamura, Koichi Kurokawa, Yukio Kato, Kenji Hashimoto

It is well known that ground vibration by blasting is mainly related to a distance and charge weight. However, it is not known the correlation between ground vibration and performances of explosives; for example, shock wave energy, bubble energy, detonation velocity and ballistic mortar value etc..

Jan 1, 1991

By Mauro F. Dobran

The use of Slot Raises has been common for many years. The following presentation will compare various methods of developing these Slot Raises and introduce two new ones.

Jan 1, 1996

By Rowland Jones

This type of quarrying is very much different from that of established quarries in developed countries, demanding somewhat unorthodox techniques to produce the variety of materials required. The demands on the resourcefulness of-the quarrymaster can be very testing, and produces quite a different breed of individual than what is normally met in managerial status in quarries of developed nations.

Jan 1, 1977

By Ery Wardhana, Stefanus Jagad, Relinda Sanistya, Hasucita Tausi, Rido Situmorang

The blasting process is one of the most high-risk activities in mining operations. Shotfirers and blasting crews face hazards from slope failure, toxic gas and fumes, or unstable ground condition every day of the blast. But on the other hand, to ensure all of the holes are detonated, shotfirers are required to reenter the location to check. With advances in technology, nowadays the use of drone in mining is not something that is rarely seen. It has been used for mapping and slope-monitoring. This paper will discuss the application of drone for blasting process in a mining pit in East Kalimantan, Indonesia. By using drones, it is not only safety factor which can be improved but also operational efficiency and technical analysis. The duration it takes for post blasting process can be reduced because the drone can directly enter the location after blast. The technical analysis for the blast can also become more comprehensive, as the before-after photos and video documentation can be taken with wider view. It helps with fly rock calculation and fragmentation analysis too.

Feb 6, 2023

By Paul V. Sterk

In the early 1980's, the Homestake Mine converted from labor intensive methods such as open cut-and-fill mining to Vertical Crater Retreat (\/CR) bulk mining and mechanized cut and fill. This transformation occurred as a result of high costs and low productivity associated with open cut-and-fill mining. Use of Vertical Crater Retreat allowed Homestake to contain waste development rock within the mine to further decrease costs since the voids created from VCR stopes provide a good receptacle. The need to access these voids from surrounding development to facilitate waste dumping precipitated the development of drop raising. This system is cheaper than raise boring because it allows drilling into the top of an open stope without the expense of raise boring cutouts or equipment. It's safer than conventional raising since access from the bottom is not required. Two methods of long hole raising or "drop" raising have been successfully developed at the Homestake Mine and can be categorized as Ring Drill Drop Raising using 2-1/4 inch holes and VCR Drop Raising using 6-1/2 inch holes.

Jan 1, 1991

By W. J. Birch, R. Farnfield, G. D. Rangel-Sharp

It is widely recognised that complaints from members of the public relating to blasting operations are related to both ground vibration and air overpressure. It is also known that a complaint is more likely to be generated if the person is inside of a structure at the time of the blast. Reports relating to such complaints often refer to ‘noise’ inside the structure with terms like ‘rattling’ commonly being employed. Such acoustic response is widely perceived within the blasting industry to be directly related to high levels of air overpressure although there appears to have been very little research carried out specifically related to this effect.

Jan 1, 2007

By Oldrich Machacek

Seismic explosives are very important tools in the search for oil and gas. Changes and new techniques in seismic exploration methods are also demanding new developments in seismic explosives. This article concentrates on three problems, characteristics of surface seismic explosives,causes of fires in application of surface seismic explosives and new developments in downhole seismic explosives.

Jan 1, 1985

By D D. Garg, D A. Wasson

Open pit blasting in India uses two types of explosives. First there are bulk explosives for wet and dry holes, and there are packaged explosives. The Indian open pit coal mining is projected to use 190 thousand metric tons of explosives in 1995. This volume is projected to grow for the next ten years, whereas the underground coal mining will hold fairly constant.

Jan 1, 1995

By J Paul Tidman, Stephen H. Chung

One of the requirements in open pit gold mines is to minimise the mixing of ore and waste. Dilution can be reduced by choke blasting and control of the initiating sequencing. The authors have used the DMC computer model (developed at SANDIA) to examine the effects of timing and charge distribution on ore dilution. The model has been calibrated by measurements of vertical uplift derived from high speed videos made at the Dome Super Pit in Timmins.

Jan 1, 1997

By Don Rapp, Rufus Flinchum

Air blast and flyrock are two of the most critical concerns facing the blaster of today. This paper will provide the blaster with proven procedures for recognizing open face and bench surface problems, explain various surveying methods, and provide the mathematical formulas for calculating and designing proper hole placement and explosive load configuration. A concept called "Pattern Footage" is utilized in conjunction with a USBM study to develop blast designs aimed at minimizing air blast and flyrock. In addition to this main focus, this concept can be used in shot displacement and cast blasting design.

Jan 1, 1993

By Scott Stephenson

Making a tunnel through solid rock can sometimes be a dangerous task. Many things must be considered in order to complete such a task safely, and efficiently. Prior to starting things must be known such as, the type of rock, the purpose for the tunnel, the destination point, then angle of decent (or ascent). Once these things are known, the method to proceed must be considered. Factors such as cost, feasibility, and time to completion must be taken into account.

Jan 1, 2009

By Francis O. Otuonye

A time series and system analysis modeling technique was applied to signals from strain egages mounted on a fully grouted resin roof bolt and signals from accelerometers mounted on the bolt head and roof rock to determine the roof bolt's response to repeated blast loading. The derived model gives a comprehensive quantitative description of the modes of vibration of the roof bolt response to each blast loading. The damping ratios and natural frequencies of the modes of vibration can reveal the alteration of the process dynamics due to the deterioration of the roof rock and can be used to identify the incipience of instability in the roof bolt system.

Jan 1, 1987

By T. Palangio

Most blasters wouldn’t think of initiating a shot without a seismograph to record vibration and air blast results. Some might even measure the velocity of detonation but few surprisingly record the event on video, photo document loading conditions or take pictures before and after the shot. This paper discusses digital imaging, the equipment, methods, techniques and information that can be learned from digital pictures taken in the field during blasting operations. The guy who said “a picture is worth a thousand words” probably understated it.

Jan 1, 2008

By Tom Donnelly, Roger C. Ilsley

Remote telecommunications seismographs were used to monitor blast vibrations at two historic structures in Cedarburg, Wisconsin during adjacent sewer line construction. The purpose of the vibration monitoring program at the historic structures was to maintain blast vibrations below limiting tolerances established by the Wisconsin State Historic Society.

Jan 1, 1991

By Kaby K. Kabongo

The paper is drawn from a project intended to explore a technique of prediction, control and optimization of fracture in coal induced by blasting. It evaluates the fines generated in coal submitted to dynamic loading stresses in an impact stamp mortar. The aim is to analyze a complex phenomenon of coal response to blast-generated stresses from a series of discrete simulations of shock and gas actions in controllable processes.

Jan 1, 1995

By Robert Lee, Jay Rodgers, Kirk Whitaker

The time domain during which an explosive detonates and causes rock to fragment and displace is on the order of tens of milliseconds. Because of this, the dynamic processes that occur during this time frame often become a source of confusion when trying to analyze the performance of explosive products in decked blast designs. As an illustration, the authors have experimentally examined explosives malfunction in decked blasts through state-of-the-art measurement techniques. The interaction of explosive products and blast geometry was examined in detail using the analysis of a series of decked blastholes. Explosive and initiator malfunction in decked blasts is often considered to be entirely the result of insufficient inert decking material, however, it is shown that rock properties and dynamic burden conditions may have a significant impact on decking performance. The successful application of deck-blasting technique for control of ground vibration amplitude relies on an understanding of the true dynamic performance of the blasthole.

Jan 1, 2000