Search Documents

By S. M. H. Haddad, M. Saghaeian, R. Hejazi

"Due to limited water resources in mineral processing plants, increasing the efficiency of iron tailing dewatering system in order to obtain more usable water is very important. In this research, flocculation process, as one of the best method for water recovery, was investigated by using one organic cationic and three anionic types of flocculants with different dosages (10, 20, 30 g/ton) and iron ore tailing slurry (8 % w/w solidity) in series of graduated cylinders and obtained results were compared. it is observed that for tailing sample, the anionic flocculants have a significant effect on the settling rate of solid particles compared to the cationic types. Furthermore, effects of temperature (10, 23 and 43 ºC) and pH (2, 7 and 12) on the rate of settlement and turbidity was studied by utilizing the best flocculant. Findings showed that by increasing the amount of flocculant dosage, sedimentation rate went up and turbidity decreased. Comparison the out-put data of tests indicated that at temperature 23 °C and pH=7, the best results for both of faster settling rate and producing more clear water were reached. It should be considered that lower temperature has a more negative effect on the sedimentation rate and overflow water quality. So it will be predicted that for cold seasons, the consumption of the flocculant powder would be higher than the moderate or warm seasons. Also, coagulation/flocculation was evaluated by applying organic cationic coagulant added to anionic flocculant in three different times. Different ratios of coagulant to flocculant was examined (70%:30%, 50%:50%, 30%:70%) as well. Overall, utilizing coagulant had desirable influence on sedimentation experiments and obtaining high quality water. 1- INTRODUCTION In mineral Factories, among the important processes, solid-liquid separation process due to limited resources of water is very important and operates on iron ore tailing in settling tank as thickener in order to gain clear water for preventing water loss and applying again in plant units (Ciftci and Serhat Isik, 2017). Iron ore tailing include inharmonious compounds of iron oxides, silicates and aluminum-silicates. The percentage of solid in the tailing usually changes between 5 and 10 percent (Dash et al., 2011). One of the major problem about dewatering of tailing in thickener is solid-liquid separation of slurries with high stability because of fine particles. It means that rate of sedimentation is very slow and recovered water quality is inappropriate. This issue can be solved to a large extent by factors such as pH control, ionic strength and flocculation/coagulation process which results in aggregation of particles so that settlement by gravity is happened (Dash et al., 2011)."

Jan 1, 2018

By Francesco Vegliò, Luigi Toro, Francesca Beolchini, Francesca Pagnanelli, Stefano Ubaldini

"Biosorption is an innovative technology used to remove heavy metals from aqueous solutions from mining waters and other industrial wastes. A wider application of this alternative process is strictly dependent on the understanding of the chemico-physical aspects involved, in order to optimize the operating conditions. Mechanistic models are the most useful tools used for understanding purposes, even if the empirical models are still widely applied for their simplicity.In this paper especially propagated biomasses of Sphaerotilus natans, calcium alginate and some waste materials were tested as adsorbents for single and binary solutions containing heavy metals at different pH. The equilibrium experimental results were fitted according to empirical and physical models with growing complexity outlining the inadequacy of the predictive models; in fact, the non-ideal interactions among metals require the insertion of additional correction parameters."

Jan 1, 2003

By F. v. d. Meer, G. Kretschmar, T. Mütze, T. Leißner

"Dynamic air classifiers separate particles in a gas flow due to different particle trajectories utilizing differences in the settling velocity of particles as characteristic property for separation. The present contribution takes a close look at the separation of heterogeneous mixtures, in which valuables and gangue minerals show significant differences in density. The focus was on a moist iron ore sample, which was characterized in terms of mineralogy, grain size distribution, and particle size distribution. The material was classified at a cut size of 45 µm and at feed moistures between 0 and 6 wt.-%. Additionally to standard characterization techniques, the moisture of both products was measured as well as the yield of fines as product fraction in a corresponding processing plant. In addition, an automated mineral liberation analysis (MLA) provided information of the enrichment and segregation of individual mineral phases in the products. The MLA of the classification products reveals a selective comminution of the mineral phases and especially on overmilling of the valuables. For the first time, the separation of individual mineral phases has been assessed and compared to the classic assessment of classification processes by means of particle size analyses. KEYWORDS Dynamic classifier, segregation, MLA, selective comminution INTRODUCTION Dynamic air classifiers separate particles in a gas flow due to the different trajectories of the particles. The result of such a separation process depends on the gas throughput of the classifier, the dimensions, design and rotational speed of the deflector wheel, as well as the state of dispersion and thus the geometry of as well as the turbulence and interparticle interactions in the separation zone. Air classification of moist feed materials can be divided into several sub-process (Leschonski, 1977; Mütze et al., 2016): - dosage of the feed material, - dispersing the solid feed material into a gas stream, - feeding the dispersed material into the classification zone by pneumatic conveying, - drying of moist particles during pneumatic conveying, - separation of coarse and fine particles, and - separation of fine particles from gas."

Jan 1, 2018

By G. Alfano

This investigation is concerned with the optimization of ultrafine grinding of solids. It is focused on a dynamic classifier for recovering the fine fraction, for automatic recycling of the oversize particles and for reducing power consumption. Power consumption plays a major role in these energy intensive processes and depends on several parameters such as nature of the solid, degree of fineness of the finished product and, above all, grain size of the feed. This study indicates the optimal conditions for a dynamic classifier, that is, geometric characteristics of the apparatus and its capacity, inlet air flow rate and dimensions of the classification circuit. It is also shown that a mean grain diameter (dm) of about 2.00 µm with top size (dmax) of 50 µm can be achieved with an imperfection value of below 0.40 and energy consumption of 215 kWht-1. Keywords: air classification, dynamic classifier, jet mill, energy

Sep 1, 2012

By B. K. Mohapatra

Small manganese ore bodies in south Odisha, India occurs both as stratiform and stratabound ore bodies. These two ore bodies show contrasting mineralogical, petrographical and chemical characteristics. Stratiform type of Mn-ores consists of manganese, iron and silicate- phases in approximately same proportion. In contrast, stratabound ore bodies contain a high proportion of manganese oxides, silicates and phosphorus phases. Phosphorus is found within apatite in the stratabound ore bodies while in the stratiform ore it occurs as an adsorbed state with iron phase (goethite). Both ore bodies are low-grade (17-23% Mn) therefore do not have a market value. However, the stratabound ores are enriched in phosphorus (P2O5: >1%) compared to the stratiform ores. Both the ore types were processed through gravity, magnetic and roast reduction followed by magnetic separation techniques. The strata bound ore could be upgraded to 33% Mn from a feed of 23% by combination of dry and wet magnetic separation methods. But the phosphorus content also suits up (P2O5: 1.2%) in the processed product making it unsuitable for further use. The stratiform ores do not respond to either gravity or magnetic separation because of close association of manganese with iron phases. However, this could be beneficiated through roast reduction followed by magnetic separation. An ore with 17% Mn content could be upgraded to 40% Mn with a 42% yield and 78% recovery. The goethite, having phosphorus, converts to magnetite and is retained within the magnetic fraction, thereby reducing the concentration of phosphorus in the non-magnetic fraction, which becomes the product. This report demonstrates the influence of ore petrology in determining the up-gradational potential of manganese ore in the southern Odisha, India. Keywords: manganese ore, physical beneficiation, phosphorus rich ore

Sep 1, 2012

By R. C. Dunne

As ore grades of existing and new ore deposits continue to decrease there is ever increasing pressure to decrease operating costs to maintain profitabitabitiy at existing mine sites and for new projects. The accepted solution to this dilemma in most cases is to increase treatment rate, leading to a coarser grind, at the expense of marginal decreases in recovery. The recovery loss is usually associated with losses of liberated and composite coarse material. This paper will review the practice of coarse particle flotation, including the reagent chemistry, cell hydrodynamics, froth stability, entrainment and flotation cell design, all parameters important to the recovery of coarse liberated and composite particles. This will provide a better understanding of opportunities to improve the recovery of coarse particles. Some examples will be provided.

Sep 1, 2012

By Steven Wright, Sharif Jahanshahi, Shouyi Sun

"While there is a large industry based on recovering platinum group metals (PGM) from complex sulphide ores containing Cu and Ni, there is little information on the thermodynamics of the matte phase formed on smelting the ore and in particular the behaviour of Pt in the matte.The equilibrium between metallic platinum and industrial mattes was studied in a series of experiments where a small quantity of matte (5g) and platinum foil of 150 µm thickness (0.5 g) were equilibrated in magnesia crucibles at 1400°C under conditions where the oxygen and sulphur partial pressures were controlled.The chemistries of the phases were determined from EDS analysis using a scanning electron microscope. Line scans were initially used to confirm that the foils had attained a uniform composition across their thickness. The composition of the matte was determined from analysis of an area of matte including the small metallic droplets and dendrites.The distribution of Pt in Cu-Fe-Ni mattes (Pt: 1.5 – 3%) and solid Pt alloys (Pt: 54 – 72%) was studied. For a matte of base composition 45%Fe, 11%Ni, 8% Cu, at a base temperature 1400°C, the following behaviour was observed for the Pt distribution ratio:Under the range of sulphur and oxygen pressure of this study (log pO2 from -15 to –12.2, log pS2 from – 4.6 to –2.2), the distribution ratio of Pt between matte and alloy was independent of the sulphur and oxygen pressure, having a value of 0.04.The Pt distribution ratio increased from 0.02 to 0.08 with temperature from 1340 to 1450 oC.For mattes where the proportions of Cu and Ni were kept constant, a slight decreasing trend was shown for the distribution ratio of Pt versus the iron content (37 to 53%) in the matte but was not confirmed because of experimental uncertainty."

Jan 1, 2003

By A. Mainza, I. Govender, J. Waters

"The study of the properties of mineral processing suspensions is important in understanding how a circuit might behave. As soon as the predominantly dry ore enters a wet milling stage the ore properties undergo changes as a ‘slurry’ is created. Slurries can be classified in terms of their physical properties (particle density, solids concentration, particle size and size distribution, particle shape), and their flow properties such as rheology. Slurry flow regimes are classified into true homogeneous, pseudo homogeneous, heterogeneous and fully segregated, and only true homogeneous and pseudo homogeneous suspensions can be characterized by their flow structure. A class of the heterogeneous regime are the so-called dense phase or settling slurries - those which result in a clear water surface on standing, although they may approach a pseudo homogeneous state if suspended for a sufficient period of time. They are usually extremely difficult to characterize by their rheological properties alone and the rheological characterization of these slurries has always posed a problem, especially at higher concentrations. Previous rheological studies have focused on the individual concentrator units dealing with milling, classification, pumping, flotation, fine grinding, thickening.In this work an attempt was made to characterize two ore types (copper and a Platreef platinum ore) using a custom built Paterson and Cooke tube rheometer, at concentrations up to 43% by volume. After applying a turbulence correction, results showed Bingham plastic behavior. A conventional vane rheometer was then used to compare the rheological behavior of platinum concentrator streams. A size criteria was used to identify any rheologically dominant streams."

Jan 1, 2014

By T. J. Chen

Stone coal containing vanadium is an important vanadium resource in China. Roasting and oxidation of vanadium is the foundation for extracting vanadium from stone coal. This article takes stone coal vanadium ore in Tongshan of Hubei Province as research target to conduct oxidation roasting test on it by using a self-developed low-sodium compound additive and a new optimized technology. Firstly, use potentiometric titration, X diffraction, energy spectrum and electron probe to study valence change, occurrence and phase transition of vanadium during oxidation roasting process. On this basis, primary work is done on oxidation kinetics of vanadium by exploring the steps that control reaction rate during vanadium oxidation process and determining the related dynamic parameter ? apparent activation energy. The study shows that occurrence of vanadium in stone coal of Tongshan is mainly in illite, and that the result of phase transition in roasting process is disappearance of illite containing vanadium, formation of soluble vanadate and potassium feldspar, albite. It further demonstrates that oxidation process of vanadium is step by step (V(?)? V(?)? V(?)), and its oxidation reaction is controlled by diffusion kinetics whose dynamic apparent activation energy is E1=81.19kJ.mol-1.

Jan 1, 2014

By Jonas Addai-Mensah

In this paper, the results emerging from the several basic and applied studies performed to provide fundamental understanding of the interplay between clay pulp chemistry, orthokinetic flocculation performance, particle interactions, applied shear and dewaterability of fine clay mineral dispersions are presented, reconciled, and discussed. Modification of pulp chemistry and behaviour was achieved by using kaolinite and Na-exchanged (swelling) smectite clay minerals, divalent metal ions (Ca(II), Mn(II)) as coagulants and high molecular weight, anionic polyacrylamide copolymers: carboxylate substituted (PAM A) and 2-amido 2-methyl propane sulphonate (PAM S) (PAM S), non-ionic polyacrylamide homopolymer (PAM N) and non-conventional, non-ionic polyethylene oxide (PEO) as flocculants. Clear links between pulp interfacial chemistry, particle interactions and dewatering behaviour, resulting from the influence of hydrolyzable metal ion, pH, temperature, polymer structure type and shear, are established. Optimum conditions for improved, orthokinetic flocculation performance of negatively charged clay particles, reflecting faster settling flocs (>10 m/h) comprised: (i) coagulation, (ii) moderate agitation rate, (iii) shorter agitation time and (iv) anionic rather than non-ionic PAM. The optimum flocculation conditions did not, however, have a significant impact on the final sediment solid content of 20 ? 25 wt%. Further application of shear to pre-sedimented pulps improved consolidation by 5 - 15 wt % solid. Application of the findings and new knowledge gained to real plant tails? case studies for marked improvement in dewaterability through thickening is demonstrated.

Sep 1, 2012

By I. A. S. Brum

Brazil has large reserves of coal (7 billion tons) located predominantly in the south of the country. Despite the relative ease of exploitation, these resources have been underestimated as a source of energy. Currently the country's strategic planning aims to minimize the gap between coal and resources traditionally used in the Brazilian energy matrix. In this scenario, the processing of Brazilian coal in columns flotation appears as a promising alternative, having been successful in mineral systems containing fine particles. This paper aims to study the overall process of column flotation for a specific Brazilian coal. The material used in this study consists of fine coal that is usually discarded as waste and deposited in the tailings dams. The objective is to recover carbonaceous matter and reduce the ash and contaminants grade. The variables analyzed were the influence of size particle, solids concentration in the pulp, the concentration of surfactants and frothers to be used. The first results showed that it is possible, from a feed with around 65% of ashes, to obtain products with approximately 35% ashes with mass recoveries about 40%. Concentrations of frother (pine oil) ranged from 50 g/t to 300 g/t and the collector (diesel oil) of 50 g/t to 200 g/t. Keywords: column flotation, coal, tailings, negative bias

Sep 1, 2012

The relative abundance of coal in India compared to other fossil fuels makes it a natural choice as the primary source of fuel, be it for steel making, power generation or for other uses. The wide variations in nature and type of Indian coals formed during lower Gondawana period and categorized as difficult-to-wash due to its typical mineral matter association with the organic matrix call for suitable beneficiation techniques as the preferred option for quality upgradation. The good quality coking coals of the upper seams are fast depleting leaving behind the inferior quality lower seam coal. The lower seam coals presently being mined are mostly low volatile coking coal (LVC). They constitute about 50% of the total coking coal reserves in India. The beneficiation of Low Volatile Coking coals pose a major challenge and detailed R & D studies was taken up to study the beneficiation characteristics of these coals. The studies revealed that the liberation characteristics at coarser sizes are very poor and the coal is to be ground to finer sizes for liberation. The most important factor that determines coal cleaning efficiency is liberation of organic matter from mineral matter. To achieve liberation grinding is necessary as a result range amount of ultra fines (-0.063 mm) coal is generated. Presence of these large amount of ultrafine in the coal fines, often impose severe technical constraints affecting not only its floatability but also in the downstream treatment of the products like dewatering and cake formation particularly when it is beneficiating through froth flotation. In the present paper optimization of ultra fines (-0.063 mm) has been tried for a LVC coal of Jharia coal field for the better liberation and beneficiation of the above coal fines. It is observed that by optimized, combination of size and number of balls generation of fines can be controlled with liberation. Keywords: coking coal, liberation, floatability, dewatering

Sep 1, 2012

By Hamid-Reza Manouchehri

"Sustainability calls for maintenance, rational use and enhancement of natural resources as well as balance consideration of ecology, economy, and social justice. The challenges in mining industry call for a sustained global effort using the leverage of available technologies and emerging new technologies. The industry uses significant amount of energy with the highest portion in comminution. To conserve energy, attempts have been made to improve the efficiency of the conventional crushing and grinding equipment. Nevertheless, the new and energy efficient comminution technologies are favorable through a longer term strategy. Since crushers are more energy efficient than mills, it is logic to conduct part of milling, in the crushing stage. After years of research and development, Sandvik introduces a new crushing technology, VibroconeTM, to change traditional crushing concepts. The new crushing device is able to crush and grind particles with a higher reduction ratio, more than two fold, than that of conventional crushers. By implementation of the new technology, a suitable feed size for milling can be provided to conserve energy as well as media and liner consumption, to reduce milling circulating load or increase mill capacity. There are other benefits associated with this machine, one of them being providing a higher surface area. This paper discusses the performance of the machine and its applications for comminuting different ores."

Jan 1, 2014

By ?. S. Yusupov, V. P. Isupov, N. Z. Lyakhov, A. G. Vladimirov, S. A. Kondratiev

"Considering the shortage of lithium reserves, the desirability has been shown of studying the possibility of processing into spodumene concentrates the concentration tailings and low-grade ore reserves at Transbaikalian Mining and Processing Project (ZabGOK). The mineral and chemical composition and the particle size distribution of the mineral feed, separability and recoverability of spodumene have been studied, forming the basis for the development of a concentration process and flowsheet for the studied mineral resource. Prospects have been established for impact ore grinding in a disintegrator, the efficiency of mechanochemical processes has been shown in the separation of quartz and feldspar and the recovery of lithium from concentrates.INTRODUCTION Lithium is widely used in various industries - nuclear power engineering, defense technology, power generation, ceramics, special-purpose glass and other technologies. The increasing demand for lithium and its compounds (lithium carbonate and hydroxide) for use in the manufacture of high-tech products (lithium-based materials for chemical sources of electric power and electrochemical energy) explains the need for establishing a sustainable raw material base (Mohr et al. 2012; Moores, 2007). The main sources of lithium are spodumene pegmatites (Vladimirov et al. 2012; Garret, 2004), brines (salars), and hydromineral materials (Garret, 2004; Zeng and Liu, 2009; Kotsupalo and Ryabtsev, 2008). However, in view of the absence in Russia of extractable hydromineral resources of lithium, the practical significance of spodumene ores remains decisive. Russia controls some of the world’s largest reserves of rare-metal pegmatites holding over 8 million tons of Li2O: approximately 7 million tons on the Kola peninsula and 1 million tons in the Sayan mountains. The main lithium mineral in pegmatites is spodumene LiAlSi2O6 containing 8.1% Li2O. It can be efficiently recovered by gravitational concentration and flotation. However, most of the deposits are located in remote areas and none is currently developed. In this connection, special research is focused on technogenic raw materials, which are increasingly seen as a solution to the resource base problem (Chanturia, 2008, Kurkov and Kotova, 2007)."

Jan 1, 2018

By T. Kalliomäki, B. P. Wilson, M. Lundström, J. Aromaa

"The diffusion rate of cupric ions and limiting current density are important factors that determine the rate of copper mass transport in electrolytes proximal to the electrodes used in electrorefining. As a result, diffusion can critically affect both the rate and morphology of cathodic copper deposition thus it is crucial that it be optimized to improve production. The diffusion coefficient of cupric ion (DCu(II)) in copper electrolytes has been previously researched but the values detailed in the literature show significant variations and moreover arsenic - a common impurity - is generally excluded. Furthermore, in previous studies the models have only been validated with model solutions rather than real industrial electrolytes. In this study, the limiting current density and diffusion coefficient of cupric ion were defined for synthetic electrolytes containing copper (40–60 g/dm3), nickel (0–20 g/dm3), sulfuric acid (130–220 g/dm3) and arsenic (0–45 g/dm3). The cathodic limiting current densities were measured at three temperatures (50, 60, 70 °C) with linear sweep voltammetry using the rotating disc electrode (RDE) as the cathode. By utilizing the limiting current density, models for the DCu(II) were constructed using Levich equation. The validity of the DCu(II) model for technical use was confirmed through their application to industrial electrorefining electrolytes with known element concentrations. Consequently, this study provides improved models for limiting current density and diffusion coefficient of cupric ion that can be utilized for industrial process optimization.INTRODUCTION For an efficient copper electrolysis process, the mass transport of copper ions has to be effective. The main mass transport types of copper ions in copper electrorefining are diffusion and convection while the effect of migration is negligible. In order to maintain good mass transport, it is beneficial to keep both diffusion and convection high to maximize the limiting current density (jlim) (Bard and Faulkner, 2001). jlim is the highest current density that can flow in the cell, thus by maximizing jlim the deposition time can be minimized and the good quality of cathodic copper can be ensured. Thus, it is important to research possibilities that increase and optimize diffusion since slow diffusion in the electrolyte limits the rate of the process (Levich, 1947; Moats et al., 2000; Subbaiah and Das, 1989)."

Jan 1, 2018

Most of the Indian coking coals are medium coking and of very high ash content. Beneficiation of these coals is a must for their utilisation in coke making. During washing while the ash content of the coal is reduced, the same is expected to affect the reactive-inert ratio and the proportion of various petrographic constituents in the clean coal. This will affect the coking behaviour, including the expansion characteristics, of such coal. An increase in expansion behaviour of coal increases the wall pressure and may damage the battery wall. Therefore, close monitoring of coking properties along with drop in ash is necessary for smooth use of the coal in coke ovens. An effort is, therefore, essential to understand the impact of washing on its coking properties. The studies were carried out with captive coals of Tata Steel, India. Three medium coking coal samples namely, VII A, VI A and XI SEB seam coals of West Bokaro Colliery were used for the study. The coal samples after washing to different ash levels were subjected to the following analysis: proximate, crucible swelling number (CSN), LT GK test, dilatometer and plastometer tests and petrography. The experimental data were then analysed to assess the relationship of various coking properties of the coal with its ash content. The studies clearly show that there is a strong impact of beneficiation of the coal on its coking behaviour. The impacts are more at lower level of ash in the clean coal. In general, the coking properties increase with a decrease in ash. This is primarily due to an enrichment of vitrinte materials in the clean coal and an increase in the reactive-inert ratio in the coals. However, the most important impact of the lowering ash is on the increase in the swelling nature of the coal. The coals with lower ash become highly expanding in nature. This may be very critical from operations of coke ovens point of view, especially stamp charged coke ovens. Necessary precaution should be taken in selecting the other coal blend constituents when these coals are beneficiated to a very low level of ash content.

Jan 1, 2014

By Ingvar Ymén, Alexandra Lundmark

"The depressive effect of dichromate on galena was evaluated with chemical experiments and small-scale depression experiments at a pH of around 12. The depressive effect was measured with Dynamic Vapor Sorption (DVS), which measures the water uptake of a sample as a function of the % relative humidity. The depression is due to PbCrO4PbO, which in the presence of Ca2+ and SO4 2- forms a more or less amorphous solid solution (Pb,Ca)(CrO4,SO4)PbO, which clogs to the surfaces of the ore. Free Pb2+- ions are needed for depression to occur and at high pH Pb2+ - hydroxide complexes, supply enough Pb2+ - ions to precipitate (Pb,Ca)(CrO4,SO4)PbO. In air CO2, precipitates CaCO3 which slowly lowers pH, precipitating more (Pb,Ca)(CrO4,SO4)PbO and CaCO3 on galena. Similar experiments where performed with five alternative depressors whereof phosphate, which forms an amorphous precipitate of approximate composition Pb3Ca13(PO4)10SO4, gave the best results. Phosphate was tested in laboratory scale flotation experiments giving encouraging results.INTRODUCTIONWithin Boliden Mines, concentrating of copper and lead from complex sulfide ores is performed by bulk flotation, meaning that copper and lead are concentrated in the same product. Downstream, copper and lead are separated by flotation of chalcopyrite, and depression of galena. Boliden has for many decades used sodium dichromate to depress galena (reference 1). Dichromate is both toxic and carcinogenic and Boliden has for many years investigated several alternatives. So far, however, the best results have been obtained with dichromate. Since Boliden has tried to substitute dichromate for a long time without finding a process as effective, Boliden decided to clarify the function of dichromate in the depression of galena and on the basis of the outcome find alternative depressors with similar function. This study was given to RISE Bioscience and Materials / Surface, Process and Formulation as a consultancy assignment. This paper presents the outcome of the combined efforts of Boliden and RISE."

Jan 1, 2018

By J. Yianatos

The regrinding stage is necessary to achieve the particle size (liberation) for the final upgrade in the cleaning flotation process. At present, vertical mills (Vertimill) are employed at industrial scale, using small steel balls as grinding media. The regrinding process characterization requires mixing regime knowledge along with the mean residence time of the liquid and solid phases. The residence time distribution (RTD) and the actual mean residence time estimations from theoretical relationships are complex due to the presence of three components (solid mineral, balls and water), mass transport characteristics and segregation affecting solid holdup. Therefore, the experimental RTD determination is suitable for industrial mills. In this work, RTD measurements were performed in two different industrial flotation plants. Both plants operate with Vertimills of 1000-1500 HP in the regrinding process with different circuit arrangements according to the plant treatment capacity. The RTD was measured using the radioactive tracer technique. This technique allows for non-invasive tracer detection where the procedure consists of selecting a liquid (Br82 in aqueous solution) or solid (irradiated solid) tracer for RTD data acquisition in real time. The RTD was modelled by the Large and Small Tanks in Series (LSTS) model, which allowed the characterization of the different mixing regimes for both liquid and solids in the regrinding mills. Effective mean residence times in the range 2-11 min were obtained with RTD shapes similar to those obtained in tumbling ball mills. It was found that residence times of liquid and fine particles were similar, which is consistent with results observed in other mixing systems, e.g. mechanical flotation cells. Also, the mean residence times estimated from the RTD allowed the mass balance adjustment to be validated from metallurgical sampling data. RTD estimations are useful for better understanding the Vertimill behaviour and to identify the actual breakage rates. Keywords: vertical mill, residence time distribution, particle size, modeling

Sep 1, 2012

By I. A. Podkamennyi, O. E. Kovalchuk, G. P. Dvoychenkova

"Using the methods of electron microscopy and IR spectroscopy, mineral components in the run-of-mine kimberlites and on the surface of diamonds were identified. The mechanism and sequence of mineral formation on the surface of diamond crystals were established. Systematization and classification thereof were undertaken for the first time ever.INTRODUCTION The high content of diamonds sized -5 mm in the kimberlite ores of Western Yakutia determines their processing depth in the size class 0.5 mm and finer [1, 2]. These diamonds are recovered by grease and froth separation based on the natural hydrophobic properties of the crystals. When refractory altered kimberlite ores are fed into the industrial process, the performance of grease and froth separation of the diamond ore greatly deteriorates. [4, 10, 15, 17]. Altered kimberlites are known to contain up to 90% of secondary minerals. This reduces by up to 40% the recovery of diamonds by grease and froth separation. [6].Diamond crystals from the grease and froth separation tailings were investigated. On the surface of the examined diamonds, hydrophilic mineral formations were identified, responsible for reduced recovery by physicochemical separation methods [3, 12, 18]. The aim of this study was to identify and describe the relationship between the composition of kimberlite ores and mineral formations on the surface of diamond crystals in order to systematize, classify, and then develop methods of removal in grease and froth separation processes. MATERIALS Following materials were examined in this study: - kimberlites of various material composition, - resulting slimes, - diamond crystals from kimberlite ore processing products."

Jan 1, 2018

By S. S. Yu

In this paper, the producing process of using V2O3 as raw material to obtain vanadium nitride was analyzed through the means of thermodynamic. The analysis shows that conversion follows the principle of reduction step by step in the conversion process of V2O3. The temperature of the reaction system has prominent influence on the nitrogen content of products, and the reaction is very sensitive to temperature. As raising temperature, the fine grain structure of the nitrides is more evident, and the grain size of nitrides increases. At 1703K, the nitrogen content of the products tended to be constant after soaking over 3 hours.

Jan 1, 2014