Search Documents

By Lev Filippov, Vyacheslav Severov, Inna Filippova

"Reverse cationic flotation is a very efficient method of beneficiation of oxidized iron ores when you need to separate hematite and quartz. This method can be also applied to reduce silica content in the magnetite concentrates obtained by wet low-intensity magnetic separation. However, cationic flotation in this case is less effective due to the presence of Fe-Mg-Al-bearing silicates as amphiboles in magnetite ores. These silicates are concentrated in magnetic products and determine the difficulties of their separation from iron oxides when amines and starches are used as collectors and depressants, respectively. The recalculation of the results of the electron microprobe analysis of three calcic Fe-Mg-Al-bearing amphiboles used to characterize cation distributions in structural units and to obtain structural formulas in accord with stoichiometric limits was conducted. The Mössbauer spectroscopy was used to examine the validity of the empirical estimation of cation distributions in amphiboles. The studied samples are metamorphic pargasite and ferrotschermakite and volcanic magnesiohornblende. The crystallographic analyses of the amphibole samples exhibited their heterogeneous surfaces explaining worse floatability of amphiboles with dodecylamine at pH 10. The electrokinetic measurements showed that the position of the isoelectric point of amphiboles is related to a substitution of Al3+ for Si4+ in tetrahedral sites and to an amount of Mg2+ cations in octahedral sites. Thus, the dodecylamine adsorption onto amphiboles through electrostatic interactions is mainly affected by a distribution of these cations in tetrahedral and octahedral sites of amphiboles. In addition, the effect of starch on the depression of Fe-Mg-Al-bearing amphiboles during flotation can be attributed to the presence of metal ions on the amphibole surface, which are capable of forming strong chemical complexes with starch molecules."

Jan 1, 2014

By X. S. Yuan

With a demand for increasing energy efficiency and a need for improving bitumen recovery, a highly integrated solution for sustainable lease development of Aurora North of Syncrude has been proposed and implementation plans are underway. Flocculation and thickening technology as an important component of the integrated solution provides Syncrude an opportunity of rapid heat recovery from tailings and more flexible tailings closure and reclamation options. Flocculation of fine-particle suspensions by polymers is a non-equilibrium process whose performance is strongly influenced by physical and chemical variables. While polymeric flocculants are frequently used to establish the chemical conditions favorable for flocculation, the actual performance of a flocculation process generally depends more on the physical variables, such as the hydrodynamic conditions in mixing the flocculants and slurry. In order to study the effect of hydrodynamic conditions on flocculation of Syncrude fine tailings, a standardized laboratory test procedure called power flocculation has been developed in comparison with the conventional manual mixing methods. It is shown that the agitation speed and time in conditioning the flocculant solution and the slurry have a profound effect on the flocculation performances measured by initial settling rates, supernatant clarity and sediment density. It was found that the optimum bench test conditions for power flocculation of Aurora fine tailings with a sand-to-fine ratio (SFR) of about 1:1 are conditioning of the flocculant solution and the tailings slurry at 250 rev/min to 300 rev/min in 20 s to 40 s. The test results are inter-preted with a flocculant adsorption/redistribution kinetic model that helps understanding of the effect of hydrodynamic conditions on flocculant adsorption, floc formation and floc growth.

Jan 1, 2014

By F. M. Zafar Kaifi

Magnesite producing companies rely on high grade purity MgO. The mineralogy of magnesite has a significant impact on the manufacturing of magnesite bricks. The manufacturing process of bricks companies utilizes 90% magnesite from 85%~90% MgO. The main objective of the magnesite bricks was to utilizes the indigenous raw material available in bulk quantity. With better under-standing of chemistry of the mineral species and strict control of bricks manufacturing/processing conditions can be better produce efficiently, a low cost high quality bricks with minimum detrimental environmental impact.

Jan 1, 2014

By Fu Ping-Hao, Sergio Mauricio Vianna, Ewen Silvester, Emmy V. Manlapig

"Over the last 5 years, an ambitious project has been undertaken at the Julius Kruttschnitt Mineral Research Centre (JKMRC) aiming to isolate, study and, if possible, model the effect of particle size, liberation and collector adsorption density on the floatability of mineral particles. As part of this project, we have conducted highly controlled flotation test-work, combined with state-of-the-art solution and surface analytical techniques such as High Performance Liquid Chromatography (HPLC), Time of Flight Secondary Ion Mass Spectroscopy (TOF-SIMS) and detailed mineralogical analysis to fully characterize the flotation behavior of a natural ore.The flotation tests were undertaken using a high-grade lead-zinc ore from BHP-Billiton’s Cannington mine (Australia) in a specially designed continuously operated laboratory scale flotation rig. Solution and adsorbed collector concentrations were measured independently during the course of the flotation tests using HPLC based ex-situ techniques. Liberation studies were performed using the JKMRC Mineral Liberation Analyser (MLA) on selected size intervals of different streams to estimate the specific surface area of galena. These results were used to calculate the collector adsorption density (collector coverage) on galena particles, with the eventual aim of developing a mathematical model describing the relationship between pulp chemistry, feed mineralogy, and floatability of galena particles."

Jan 1, 2003

Gold thiosulfate complex is difference with gold cyanide complex, which is easily adsorbed on activated carbon while gold thiosulfate complex cannot be satisfactorily recovered by activated car-bon. However, Gold thiosulfate could be recovered by activated carbon if cyanide is added into the thiosulfate solution. To avoid the cyanide solution, this paper will review several possible processes to recover the gold from thiosuldate solution: such as the cementation with metals, ion exchange resin and solvent extraction. The gold cementation with the powders of zinc, copper, iron and aluminium will be discussed. The advantage and disadvantage of each are compared. The consumption of thiosulfate and copper and feasibility of solution recycling will be discussed. The gold recovery by some ion exchange resins will be suggested. The processing conditions, its applications and the resin elution methods will be presented. The gold recovery by using solvent ex-traction will be reviewed. The processing conditions of solvent extraction process are discussed and compared.

Jan 1, 2014

By D. Tang

The froth zone in a flotation cell is recognised as a region which contributes to the overall flotation performance. Froth recovery is a measure of the efficiency with which the froth phase delivers particles arriving at the pulp-froth interface to the concentrate. Poor froth recovery in scavenger stages is generally attributed to poor froth stability. The key indicators of froth performance: froth recovery, entrainment and water recovery were measured in an OK3 pilot cell installed at a zinc concentrator in Australia and supplied with scavenger feed. Cell hydrodynamic and pulp chemical conditions during the operation of the cell were also measured as well as bubble growth across the froth phase. The objective of the work was to assess the impact of a number of commercial frothers on the froth performance in the OK3 cell and assess the suitability of using bubble growth as an indicator of froth stability.

Jan 1, 2014

"The JKMRC researchers have been redeveloping the suite of breakage testing techniques to more realistically align with the breakage environment in comminution equipment. Computational modelling, especially with the DEM, has highlighted the modes of impact and contact, along with the energies of these interactions in a wide range of equipment. This has driven the need to match these modes in laboratory ore characterisation tests. The objective has been to build a continuum of breakage tests and associated models that span the required range of breakage forces and environments. The ore sample is subjected to a sequence of tests covering: abrasion (surface breakage) of angular through to smoothed particles; single particle impact from high energy single impact breakage down to low energy; incremental breakage covering 60 mm down to 50 µm particles; particle strength distribution; and bed breakage over a range of compression and energy input. These tests are suited to multi-component ores with a distribution of strengths. A modelling technique is also being developed to utilise primary breakage for modelling breakage under different types of confinement. This paper draws together these techniques, previously published by the authors, into a coherent whole. The suite of tests is approaching the point where a fixed set of tests can be used to model the performance of a full range of equipment, removing the need to conduct repeat ore characterisation tests for each different piece of equipment incorporated in a circuit design. This path should open up the application of different circuit configurations and novel equipment in comminution circuit design.1 INTRODUCTION Comminution modelling utilizes a wide range of ore characterisation techniques and methods to deal with the range of comminution equipment available for production use. In general, the tests have been designed to correlate with specific pieces of equipment, using calibration factors to provide the link between the small-scale test and industrial-scale performance. The majority of tests focus on estimating the power requirement of process equipment to achieve a desired throughput and grind size. Overall, this approach has achieved acceptable outcomes in the past, but the reality is that equipment sizing suffers from considerable uncertainty, in excess of ±20% is not uncommon. This uncertainty is covered by safety margins and automatic scaling factors in equipment selection. In striving to improve reliability, the industry tends to add more adjustment factors to the tests, and design margin rather than question the basic validity of the testing process. As the tests are often correlated to production equipment via carefully guarded databases, they are also locked into historic operating inefficiency, not providing direction or revealing opportunities to improve production efficiency in comminution equipment or circuits. Safe in the knowledge that they are achieving the expected production based on test work predictions, a site is unlikely to set their sights on reducing specific energy consumption by 10%."

Jan 1, 2018

By Stefaan J. R. Simons, Michael T. Spyridopoulos

In this paper the effect of humic substances (natural surfactants), electrolytes and solid particles on bubble coalescence, and as a consequence on froth stability, has been investigated. We formed two bubbles of equal size and forced them to collide using a novel experimental apparatus. The interactions were recorded by a high-speed camera, the images of which helped to determine the coalescence frequency and the coalescence time, as well as the mechanisms of the interactions. Two types of humic substances were used, along with three different electrolytes. Humic substances appeared to have a considerable effect on bubble coalescence, while the effect of electrolytes was minimal. Moderate and high hydrophobic glass spheres were used between two bubbles. Very hydrophobic spheres promoted fast bubble coalescence, while moderate hydrophobic spheres had no effect. We present data of coalescence frequency and time, as well as images of the coalescence events.

Jan 1, 2003

By Yuhua Wang, Huilan Yang, Yanqing Jiang, Dongfang Lu

"Generally, the concentration of bauxite flotation tailings is around 10%, a large amount of water in tailings needed to be recycled in the flotation process. Sedimentation and dewatering properties of tailings were investigated under different conditions. Surface high negative charges on mineral particles are the key factor to destroy the settlement of tailings when the pulp pH is around 8.9. Hence, the modification of pulp pH around 7 is necessary to the diminution of the repulsive force between mineral particles and then the acceleration of sedimentation of tailings. Anionic polyacrylamine with molecular weight of 14 million is the best flocculant for the settlement of tailings in all tested polyacrylamines. P-toluene sulfonic acid shows better properties than hydrochloric acid for pulp pH adjustment when anionic polyacrylamine with molecular weight of 14 million is used as flocculant. Although the flotation of diaspore is depressed in the presence of polyacrylamine using sodium oleate as collector, but the recycling water traded by the combination of ployacrylamine and p-touenesulfonic acid does not show the depression effects on the flotation of bauxite ore. The lower residual content of polyacrylamine in recycling water treated by the combination of ployacrylamine and p-touene sulfonic acid plays an important role. INTRODUCTION Generally, the waste water generated from mineral processing plant is usually treated by sedimentation, oxidization, electrodialysis, ions exchange, active carbon adsorption and flotation technology, and the treated water is also used again in the industrial process. Flotation was adopted widely to improve the quality of bauxite from low grade diasporic bauxite in China. For flotation, the grinding fineness of bauxite is over 90% -0.074 mm, sodium carbonate and sodium hexametaphosphate were used as regulators, so the tailings pulp is very difficult to settle and be dewatered (Y. Wang et al., 2004; Y. H. Wang et al., 2007; Wang Yu-hua et al., 2008; Wang Yuhua et al., 2011). The water recycling of bauxite tailings are becoming the highlight for the industrial application of the flotation process for bauxite ore. Researchers in China shift their attentions onto this topic."

Jan 1, 2018

By P. T. L. Koh

The effect of particle shape on the flotation process has been investigated in laboratory experiments with monosized spherical ballotini and roughly ground ballotini. The particles were treated by partial methylation with trimethylchlorosilane to achieve varying degrees of hydrophobicity. In flotation, the process of film thinning and liquid drainage is critical in the formation of a stable bubble-particle attachment and this is affected by the particle shape and surface hydrophobicity. The rate of attachment affects the overall flotation rate. Flotation tests with different particle sizes at various degrees of partial methylation have been performed in a modified Denver cell. Predictions from a computational fluid dynamic model of the cell which incorporates fundamental aspects of bubble-particle attachment are compared against flotation test results. Contact angles of the particles have also been measured using the capillary rise technique to indicate surface hydrophobicity.

Jan 1, 2014

By G. P. Karmakar, K. K. Chandan

"The drilling mud is an essential part of the drilling process, which plays a major role in keeping safe and efficient oil and gas well drilling. In the oil industry, bentonite clay dissolved in water produces the simplest type of drilling muds. Bentonite clay contains montmorillonite particles. These particles are dispersed uniformly in water and such dispersions are used in various industrial products like paints, ceramics, pesticides and drilling muds. The bentonite clay easily dissolves in water and increases the viscosity of the water, which is one of the most important properties of a drilling mud. Bentonite has the highest swelling capacity, which is responsible for building up of the viscosity of the clay-water system. The flocculation behavior of bentonite is one of the major concerns for the performance of the water-based drilling mud in the oil and gas well drilling process. The behavior of drilling mud greatly depends upon the quality and quantity of bentonite clay, as well as the additives that are used in their formulations. In this work, a comprehensive study has been carried out to find out the effect of added polyacrylamide (PAM) polymer, surfactant, pH and salt concentrations on the dispersion/ flocculation characteristics of bentonite clay-water system. It has been observed that the increase in PAM dosage reduces the residual turbidity and improves the settling rate of the bentonite particles. The flocculation rate has also been found to be better under higher pH conditions. The combined effect of salt concentration and PAM dosage improved the overall flocculation efficiency of the system.INTRODUCTIONIn the oil industry, bentonite clay dissolved in water produces simplest type of drilling muds. Bentonite clay containes montmorillonite particles. These particles are dispersed uniformly in water. Such dispersions are used in various industrial products like paints, ceramics, pesticides and drilling muds (Akther et al., 2007). The bentonite clay easily hydrates in water and increases the viscosity of the mud system (Razi et al., 2013; Meng et al., 2012). Bentonite clay in the drilling mud increases the viscosity which is one of the most important prop erties of a drilling mud. Bentonite has the highest swelling capacity, which is responsible for the building up viscosity of the clay-water system (Sonmez et al., 2013). The drilling mud is an essential part of the drilling process, which plays a major role in keeping a safe and efficient oil or gas well drilling (ASME, S. S. C., 2005). The flocculation behavior of bentonite is one of the major concerns for the performance of the water-based drilling mud in the oil or gas well drilling process. This behavior of drilling muds greatly depend upon the quality and quantity of bentonite clay, as well as the additives that are used in their formulations (Yu and Amanullah, 2005; Akther et al., 2007). Bentonite particles form aggregate under certain conditions including high temperature, and high concentration (Luckham and Rossi, 1999). If the quality of bentonite is not sufficient to accomplish intended viscosity of the muds, it is essential to add certain additives to increase the viscosity and prevent aggregation of the system (Razi et al., 2013). The anionic polymer bearing sample can build up inter-particle bonds between the polymer and clay particles. The addition of various additives like, polymers control the dispersion and enhance the viscosity of the mud by controlling the flocculation of montmorillonite particles in bentonite dispersion (Heller and Keren, 2002; Mahto and Sharma, 2004)."

Jan 1, 2018

By Rodney J. Hundermark, Sharif Jahanshahi, Shouyi Sun

"The major platinum producers in South Africa make use of electric furnaces for the melting of PGM bearing nickel - copper concentrates. To gain better understanding of the furnace operation, research was conducted at CSIRO Minerals in Melbourne, Australia. One aspect of the research project was the investigation of the factors affecting the electrical conductivity of melter type slags.Electrical conduction in slags can occur through two mechanisms: ionic and electronic. There is good understanding of the ionic mechanism. In slags containing high levels of iron, the dominant mechanism is electronic. There is limited understanding of the electronic mechanism and one of the aims of the research was to investigate this mechanism further.Experimental work was carried out on Al2O3.CaO.FeOx.MgO.SiO2 slags similar in composition to the melter slags. Conductivity increased significantly with iron oxide content. Above 20wt% FeOx, electronic conduction was significant and the conductivity varied with the oxidation state of the slag. As the iron oxide content was increased further, the electronic mechanism became more dominant. The conductivity reached a maximum at around pO2 = 10-7 to 10-4 atm., although this value was dependent on the total iron oxide content and basicity of the slag."

Jan 1, 2003

By M. Unesi, S. Haj Mohammadi, M. R. Abdoli, M. R. Garmsiri

"Hydrocyclone-thickener circuit is a promising solution to enhance the dewatering efficiency in mineral industries. The challenges in the circuit is reducing particle size in the thickener feed and the good feature is a rise in the retention time of sediments in the thickener. In this work, the effect of particle size, bed depth and residence time on the thickener performance were investigated. In this order, pilot scale columns were employed at Sarcheshmeh and Shahrebabak copper complexes. Furthermore, the influence of residence time was differentiated due to the variations in the bed depth and settling flux. Moreover, a new approach was introduced to estimate solids residence time in the thickener. results indicated that with smaller particles that are introduced to the column, the bed density as well as thickener discharge solids concentration dropped significantly. It was found that thickener discharge solids concentration fell from 59.6 to 33.8 % with reducing particle size from 130 to 22 µm in the settling flux of 20 t/m2/day. Additionally, it was found that longer residence time and deeper bed resulted in an increase in the thickener performance while the bed depth has a stronger effect. It was proved that employing a hydrocyclone prior to the thickener resuted in an increase in the dewatering efficiency.INTRODUCTION Thickeners are widely employed in mineral industries to recycle tailings and concentrate water content. A limited fraction of suspension water content is recycled using a thickener. For instance, about 50 percent of tailings water content could be recycled using a shallow bed thickener during copper processing. Since the scarcity of global water resources became more serious, the demand for improving dewatering efficiency in mineral industries became more significant [1]. A number of solutions were recommended to enhance dewatering efficiency of thickeners including optimization of current thickeners, employing deep bed thickeners and utilizing thickener-filter or hydrocyclone-thickener circuits. Optimization of existing thickeners is essential, however, it does not meet the significant demand for recycled water. The application of deep bed thickeners (known as paste thickeners) has been rising in the mineral industries [2] due to a higher dewatering efficiency while its costs is remarkable."

Jan 1, 2018

By Andrei Yevdokimov, Ivan Sidorov, Olga Lanchakova, Olga Khmelnitskaya, Tatiana Chikina

"The paper focuses on the results of the research on development of hydrometallurgical process of gold recovery from refractory sulfide flotation concentrates based on fine and ultrafine grinding. Refractory concentrates (the degree of refractoriness is 16.9%-82.6%) were chosen for testing. The efficiency of the process based on fine and ultrafine grinding to treat flotation concentrates with gold intergrown with sulfides and rock-forming minerals was shown. Based on the test work conducted, the process option was chosen. In included grinding of flotation concentrate to the size of 98% minus 20µm in a bead mill, lime treatment with air blow, CIL, filtration and detoxification of liquid phase of the slurry. This process (compared to the basic option) provides the recovery of gold from 82.6%, up to 94.0% and decreases the residual grade in the tailings from 3.3g/t to 1.1g/t at the consumption of 12.6NaCNkg/t. Based on the results of the test work and pilot plant testing, project design criteria of flotation circuit at a Russian plant was developed."

Jan 1, 2014

By H. H. Li

Reverse flotation is usually used for hematite/silica or bauxite/clay flotation separation in which the silica or clay is floated and rejected. Some properties of these silicate minerals such as particle size and surface characteristics have significant effect on their flotation behaviours. Firstly, the silicate mineral particles (especially clay minerals) generally have fine particle size (< 5 microns) in their natural states or due to overgrinding and they display poor flotation kinetics, consequently having low flotation recovery. Secondly, the wettability difference on different particle basal planes influences the affinity for adsorptions of different types of chemicals such as collectors or macro-molecule. Common polyacrylamide (PAM) flocculants can be used to minimize the exposure of the most hydrophilic planes of clay particles via hydrogen bonding but they can not efficiently enhance the overall particle surface floatability due to the hydrophilic properties of this type of macromolecules. A novel method to improve both flotation kinetics and surface wettability of silicate minerals has been developed and studied. That is to use a temperature-sensitive polymer, poly (N-isopropyl acrylamide) (PNIPAM), as a process aid in the flotation of silicate minerals. Unlike PAM polymers, PNIPAM can induce a hydrophilic/hydrophobic transition on the particle surface when the temperature is changed to be lower or higher than its critical solution temperature (CST). At a lower temperature, the PNIPAM adsorbs on the particle surface via hydrogen bond similar to PAM. It induces strong hydrophobic aggregation when the temperature is increased above the CST. Thus, both floc size and mineral floatability are greatly increased. The flotation results show very good flotation performance and the addition of conventional flotation collector was no more required because the increased particle surface hydrophobicity induced by PNIPAM. Contact angle measurements explained the role of PNIPAM in manipulating particle surface hydrophilic/hydrophobic transition.

Jan 1, 2014

By Massimiliano Zanin, William Skinner, Owusu Clement, Jonas Addai-Mensah, Daniel Fornasiero

This paper highlights the importance of pulp aeration in the selective separation of chalcopyrite from chalcopyrite/pyrite mixtures of varying pyrite content (20-80 wt.%). Laboratory batch flotation studies and oxygen demand tests were performed to predict the optimum amount of air required for the selective separation of chalcopyrite from pyrite. The pulp oxygen demand was shown to increase with increasing pyrite content but decrease with time as more air is introduced into the system. Complementary batch flotation tests showed significant improvement in chalcopyrite flotation under moderate pre-aeration of the pulp. However, a continuous decrease of chalcopyrite flotation was observed under highly aerated conditions. The amount of air required to achieve maximum chalcopyrite flotation recovery correlated positively with the mass fraction of pyrite in the pulps. The greater the wt.% of pyrite in the chalcopyrite/pyrite pulp, the longer the aeration time required. The optimum aeration time was established as the time before which the oxygen consumption rate constant reaches a bottom plateau. Surface analysis (XPS) indicated that the continuous decrease in pyrite recovery observed with increasing aeration time was due to the formation of more iron oxy/hydroxide on its surfaces, the same species accounting for the decrease in Cp recovery after prolonged aeration.

Jan 1, 2014

By L. Gutierrez, R. Yepsen, F. Alarcón

Chile is the world's largest copper producer which is mostly in the form of sulfides for which froth flotation is the most efficient concentration process. As a result a concentrate that contains high concentrations of copper sulfides such as chalcopyrite, chalcocite and enargite is obtained. In the last decades processing of ores containing high concentrations of enargite (Cu3AsS4) has continuously increased in Chile, which is related to the fact that ore deposits nawadays are more heterogeneous and complex. Enargite is a mineral that contains arsenic and its presence in the copper concentrates implies severe penalties. In addition, the shortage of fresh water has driven the search for new alternative sources of water, among which seawater has proved to be one of the most attractive. The objective of this research is to study the behavior of the enargite in the process of flotation using seawater, and at the same time to compare its behavior with the results obtained using conventional water. The study was carried thorugh micro-flotation tests using pure samples of enargite, at pH values ranging from 4 to 11, both in fresh and seawater. PAX and MIBC were used as collector and frother respectively. Micro-flotation tests were also done at different redox potential conditions so that the effect of the surface oxidation of enargite was evaluated in seawater. The results indicate that the recovery of copper from enargite is reduced in seawater compared to fresh water, in particular at the pH values close to those of the formation of the first hydroxy complexes of Mg and Ca. In general, the experimental data indicate that the floatability of enargite is strongly affected when seawater is used, in particular at oxidizing conditions. These results suggest that Mg2+ and Ca2+ ions contained in seawater interact with the surface of enargite forming hydrophilic species.

Jan 1, 2018

By Tilak Raj Mankhand, Mudila Dhanunjaya Rao, Kamalesh K. Singh

"Zinc dust is used for the removal of primary impurities by cementation from the zinc sulphate electrolyte before electrowinning of zinc. However, the industrial zinc electrowinning plants has been reported that the zinc dust consumption is in large excess than the stoichiometric requirement. In the present investigation, morphology of the zinc dust has been altered by ball milling and utilized for the cementation of cadmium, which is one of the major impurity and compared the change in the rate of cementation with original zinc dust. Initially, 325 mesh size zinc dust was used for the optimization of the excess quantity of zinc dust to be used at a temperature of 50 °C. The chemical analysis of zinc dust before and after ball milling and morphology were studied by scanning electron microscopy (SEM), and the solution was characterized by Atomic Absorption Spectrophotometer. The rate of cementation increased with increase in ball milling time. The residual precipitate obtained after filtration was also characterized by X-ray diffraction analysis. Finally experiments were conducted to study the effect of temperature and kinetics of cadmium cementation using first order reaction kinetics. Based on the integral method, the calculated activation energy for the cadmium cementation with 4-hours ball milled zinc dust was found to be 3.39 KJ/mole. INTRODUCTION Primary production of zinc in the world is carried out by hydrometallurgical route. The primary impurities in the neutralized zinc sulphate solution that cause negative effect on electrowinning are copper, cadmium, cobalt, and nickel. Copper diminishes the current efficiency and cadmium contaminates the cathode zinc (Morgan, 1977) while electro winning. Nickel and cobalt lead to perforation in the zinc deposit and prevents the electro winning process (Abrasheva et al, 1984). Due to higher electro positivity of these metal impurities than zinc, they can co-deposit with cathode zinc at the time of electrolysis. In addition to that, some possible impurities (including cobalt) in the electrolysis may lower the hydrogen overvoltage, allowing deposition of hydrogen at cathode resulting in fall of current efficiency. The deposition of zinc on the cathode is possible only at higher hydrogen overvoltage which is practicable in the absence of such impurities (Raghavan et al., 1999). Cementation is one of the prominent purification technique, and in that less reactive metal can be replaced by highly reactive metal by allowing them into precipitation. Cementation of cadmium from zinc sulphate electrolyte is being done by the addition of zinc dust."

Jan 1, 2018

By Gábor Mucsi, Barnabás Csoke, Viktor Mádai, Zoltán Molnár, Viktor Török, Ádám Rácz

The application of the stirred media mill in dry mode came to the front only in recent years, but at the same time several questions arise, such as aggregation, agglomeration, sticking on the liners and the grinding media. During high energy milling, not only the particle size reduces, but among others, in numerous cases the crystal structure and the amorphous state of the material also change due to the mechanical activation taking place. The present paper deals with experiments carried out on the ultrafine fly ash grinding in dry mode at various grinding conditions in a stirred media mill to investigate the mechanochemical effect and the energy efficiency of the mill. During the experiments the particle size distribution, particle shape, specific surface area, amorphity and crystal structure of the products were examined. The product related stress model was used for the evaluation of the effect of milling parameters on the mechanical activation. It was found, based on the experimental results, that there is mechanochemical effect on crystal structure of fly ash in the stirred media mill, as it was revealed by X-ray diffraction and FTIR measurements. The experimental results made it possible to determine the effect of the rotor circumferential speed and so the stress intensity on the mechanical activation of fly ash could be revealed.

Jan 1, 2014

By M. F. He

There are three polymorphic modifications in pyrrhotite (monoclinic, hexagonal and orthorhombic), with monoclinic and hexagonal polymorph being more abundant. The floatability of different crystalline structures of pyrrhotite (monoclinic and hexagonal) is studied in this paper. It is shown that the floatability difference of monoclinic and hexagonal is obvious and that the flotation recovery of monoclinic pyrrhotite is greater than that of hexagonal pyrrhotite using different collectors . Using butyl dithiophosphate as collector, the flotation recovery of pyrrhotite is higher than when sodium diethyl dithiocarbamate and sodium butyl xanthate are used as the collectors. Monoclinic and hexagonal pyrrhotites are more easily activated by Cu2+ in acidic conditions than in alkaline conditions, while Cu2+ can not activate hexagonal pyrrhotite when sodium diethyldithiocarbamate was used as the collector. By the measurement of contact angle, it is indicated that monoclinic and hex-agonal pyrrhotite float well and are easily activated by Cu2+when dithiophosphate was used as the collector. Using sodium diethyl dithiocarbamate as a collector, the flotation behavior of pyrrhotite was investigated. The relationship between potential and pH range for pyrrhotite flotation was established. The results show that the flotation of pyrrhotite is dependent on pulp potential at certain pH values.

Jan 1, 2014