Search Documents

The major components of sylvinite ores, sylvite (KCl) and halite (NaCl), are separated by flotation. Since both these minerals are water-soluble, the process is carried out in a saturated brine, 6~7 mol/L aqueous solution of NaCl and KCl. C16~C22 primary amines, utilized as a collector, are practically insoluble in water. In commercial potash ore flotation operations these amines are melted by heating up to 70~90°C. They are then neutralized with hydrochloric or acetic acids, and such a hot emulsion/dispersion is introduced to the flotation pulp (which is at room temperature). This is immediately accompanied by the appearance of a white precipitate in the system. As our measurements indicate, the Krafft point of dodecylammonium chloride in concentrated electrolyte solutions is much higher than 80°C, and the Krafft point of C16~C22 amines is substantially higher than that. Introduction of a hot amine emulsion into a pulp, at temperature much lower than the Krafft point for the utilized amines, must cause precipitation of the amines. Some of these species are obviously flotation-active. It is interesting to observe that in summertime, when temperatures are high-er, longer chain amines perform better. It demonstrates that the colloidal amine species that precipitate serve as active species in the potash flotation. Therefore, at higher pulp temperatures, when the temperature difference between the pulp temperature and the Krafft temperature of the utilized amine is not sufficiently large, a longer chain amine, the amine with a higher Krafft point, is more efficient. The results reveal that premixing of an alcohol such as MIBC (common frother) with the amine significantly improves flotation performance of the amine. In the presence of such an alcohol the amine disperse system becomes less turbid, and the rheology of the system less non-Newtonian. All this indicates that MIBC, which does not operate as a frother in a potash flotation system, when used as a co-surfactant, enhances the dispersion of the amine colloidal system. The appearing colloidal species perform as an active form of the collector.

Jan 1, 2014

By Jacqueline Satur, Yoshiaki Kon, Buenaventurada Calabia, Xiao Sheng Yang, Arvo Naumanen, Kenzo Sanematsu, Sayaka Morita, Tetsuichi Takagi

Granite ores are composed of silicate minerals and a variety of valuable REE (rare earth elements)-bearing minerals, however the processing technique to recover these valuable minerals is not yet developed. In this study, the recovery of REE-bearing minerals by dry magnetic separation and wet high intensity magnetic separation (WHIMS)-settling from surface sample and from drill core sample, respectively, of a granitic REE-Zr-Nb ore deposit was investigated. The two samples have different mineralogy however in both samples, light REE are commonly contained in REE carbonate minerals while Y and heavy REE are commonly contained in zirconium silicate minerals and pyrochlore. The liberation size of the REE-bearing minerals in the two samples ranges from 10-250 ?m. Previous flotation testwork conducted on the drill core sample reported high recoveries of La2O3 (88%) and Ce2O3 (88%) but low recoveries of Y2O3 (42%), ZrO2 (17%), and Nb2O5 (29%). The objective of this study was to obtain higher recoveries of Y2O3, ZrO2, and Nb2O5 by dry magnetic separation and WHIMS-settling. Both processes implemented the application of a low magnetic intensity to initially separate the ferromagnetic minerals then a high magnetic intensity to recover the REE-bearing minerals. The results showed higher recoveries of Y2O3, ZrO2, and Nb2O5 by dry magnetic separation and WHIMS-settling indicating the potential of magnetic separation and gravity separation in recovering the heavy REE-bearing minerals. WHIMS-settling is more recommendable than dry magnetic separation because of its applicability in treating a wider range of particle size. In the WHIMS-settling, the light REE, Y, and Zr minerals were recovered mainly by applying four stages at high magnetic intensity of 21,500 gauss while the weakly magnetic pyrochlore was recovered mainly by decantation of the nonmagnetic slurry after a short settling time of 0.25 to 0.50 h. (MAX.300 words)

Jan 1, 2014

By Filippov. L. O.

Metallurgical results for the copper-nickel disseminated ores were improved by using ultrasonic treatment. This has been demonstrated by processing of bubble-pulp flow in the reactor zone of a reactor-separator flotation machine. It can be explained by changes in mineral and size composition of the concentrates. Thus, the selectivity of Cu/Ni flotation for different values of the hydrodynamic parameter increases considerably. Additional effect of the ultrasound treatment has been noticed under conditions when the detachment of the gangue minerals from bubbles can be controlled. Reactor-separator has advantages over other types of flotation cells for this purpose. In fact, the weak diameter of reactors make more efficient the ultrasound effect than in conventional impeller or column flotation machines. A combination of ultrasonic treatment with original organization of gas pulp flux in the reactor-separator allows to obtain significant effects in the flotation attachment/detachment subprocesses, enhancing the process selectivity and/or recovery of substances. Increase of total recovery of copper and nickel into bulk concentrate at constant grade is 8.5% for coarse disseminated ores. For copper ore, copper recovery increased by 10% at unchanged grade of 11.7% and nickel recovery gained 17% at the constant grade of 2%.

Sep 1, 2012

By K. B. Venkatesh

In view of the importance of size reduction operations from the energy consumption point of view, during the past one hundred and fifty years a number of attempts have been made to develop a general energy-size relationship. However, to date it has not been possible to clearly define the scope of application of various laws proposed, though Bond law has been widely used with a moderate degree of success. It was, therefore, decided to carry out a thorough analysis of the batch ball mill grinding data available in the literature on several minerals that were ground under normal range of operating conditions. In particular, relationships proposed by Bond, Kapur, Voller and Morrell were examined in detail. It was found that the relationship proposed by Kapur in terms of the mean particle size provided a more accurate basis for estimation of energy. The value of the exponent of mean particle size in this relationship, a, is same as the exponent of the particle size in the expression for the grinding rate parameter: ki = Axia, provided the particle size distribution range corresponds to the self-similar or self-preserving regime. In this regime, mean particle size is proportional to the 80 percent passing size and size modulus. From the practical application point of view, it was possible to describe the variation of µ1 over limited, but significantly broad size range, using a constant value of a. Thus, by carrying out a few batches, grinding experiments over the size distribution range corresponding to the contents of the production mill, the applicable value of a can be determined. Keywords: energy-size relationship, ball mill, mean particle size, self-similar size distribution regime

Sep 1, 2012

By N. R. Mandre

In the present work an attempt has been made to study beneficiation of low-grade iron ore associated with manganese clay by selective flocculation. The representative samples obtained for this purpose were initially subjected to chemical and mineralogical studies. The chemical analyses indicated 42.56 % Fe, 6.25% Mn, 8.72 % SiO2 and 13.60 % Al2O3 in the representative sample. The mineralogical analyses carried out under optical microscope showed that the ore mineral predominantly comprised of iron oxides and hydroxides along with manganese and silicate as gangue minerals. Prior to the beneficiation studies, the samples were subjected to settling tests. These tests were carried out by using poly acrylic acid (paa), poly acryl amide (pam) and guar gum (gg) as the flocculants. From these studies it was observed that settling rate of particles increases with increase in pH and a maximum settling rate of 0.23 cm/secwas obtained at pH 9 in presence of poly acryl amide. Further, the samples were subjected to selective flocculation studies using above-mentioned reagents. From these studies better results were obtained in the experiments carried out with poly acryl amide as the flocculant. Thus, it was possible to upgrade the iron content from 42.5 to 53%, with a recovery of 92%. However, 51% Fe with recovery of 87% and 50% Fe with recovery of 94 % was obtained using poly acrylic acid and guar gum respectively.

Sep 1, 2012

By Ronel du Plessis, John C. Davidtz, Jan D. Miller

Recent results from electrochemical measurements demonstrate that trithiocarbonate (TTC) collectors are more readily oxidized to their corresponding dithiolates than the dithiocarbonate/xanthate (DTC) collectors. Based on the traditional analysis of collector adsorption, trithiocarbonates might then be expected to be effective for bulk sulfide mineral flotation. Previous bench-scale flotation research had shown that TTC collectors are very effective for the flotation of copper sulfide minerals and PGM (platinum group metal) sulfide minerals. More recently, the TTC collectors were evaluated for auriferous pyrite recovery in benchscale plant scale flotation testing in the United States and in plant tests at Anglogold in South Africa. TTC collectors were also applied in bench-scale testing of a PGM ore. In each case an improved separation efficiency was realized. Fundamental studies at the University of Utah examining the effect of collector structure (functional group, -O-CS2 versus .S-CS2), specifically with respect to auriferous pyrite flotation, are in progress. The effect of collector structure was evaluated with air as well as nitrogen as the flotation gas medium. Experimental techniques utilized included electrochemically controlled contact angle measurements to evaluate mineral hydrophobicity and infrared spectroscopy to explain collector adsorption phenomena at the mineral surface.

Jan 1, 2003

By A. I. Arol

Bentonite is an important industrial mineral with very wide application areas. Its unique colloidal, swelling, thickening and adsorption properties make it a useful agent in drilling, metal casting, and iron ore pelletizing, environmental, food, cosmetics, pharmaceuticals and many more industries. Because of its swelling property, bentonite suspensions can only be prepared at rather low solid coentrations, i.e. 8-10%. In order to process bentonite in slurries with high solid content, it was thought that a non-polar organic solvent, instead of water, can be used. Not only large amounts of bentonite can be dispersed in organic solvents but also the solvents may be regenerated. The bentonite obtained through such a process must either equal or better properties than those of untreated bentonite. In this study, the effect of organic solvents such as acetone, methyl-ethyl ketone and n-haxane on the main properties of bentonite, such as water adsorption and rheology, was investigated. It was found that bentonite can be dispersed in the mentioned organics in large quantities with no loss of quality. Keywords: bentonite, montmorillonite, water adsorption, industrial minerals

Sep 1, 2012

By Sashnee Raja, Mehdi Nemati, Ashley Sissing, Susan T. L. Harrison

"Extreme thermophiles, operating at 65 - 90°C, are finding increasing application in biohydrometallurgy These microorganisms have the advantage of exhibiting better oxidation kinetics in terms of reaction rate and extent of mineral solubilisation. These extreme thermophiles are Archae, characterised by a different cell envelope structure perceived to provide reduced structural strength in comparison to bacterial envelopes, and customised metabolic pathways.The active tank bioleaching process, used for high rate leaching, is conducted in a slurry bioreactor. Here sufficient energy dissipation is required to ensure suspension of the mineral phase as well as to sustain high rates of gas liquid mass transfer. It is well known that subjection to hydrodynamic stress of sufficient magnitude may alter the physiological state of a range of micro-organisms through changed viability (ability of the microbes to grow), metabolic activity and integrity.In this paper, we report on studies carried out to quantify the ability of the extreme thermophile Sulfolobus to withstand the hydrodynamic stress environment generated at high pulp densities in the slurry bioreactor. Both a pyrite system (as a model system) and a chalcopyrite system (as an application) were studied. In laboratory reactor systems, the nature of biological responses to stress induced at high pulp density have been identified in terms of ability of the microbes to grow, their metabolic activity and rate of leaching and cell integrity. Critical operating conditions within the laboratory reactor are identified and the mechanism mediating reduced performance considered."

Jan 1, 2003

By Teemu Väyrynen, Matti Vilkko, Antti Jaatinen, Pekka Itävuo

"This paper shows that smooth and accurate feed-hopper level control is essential for consistent cone crusher operation. The objective of the paper is to define the best practices for tight control of cone crusher feed-hopper level. The paper discusses the challenges involved in a delay-dominant level control problem (specifically, dead-time-induced performance and stability issues, mass flow disturbances, process and actuator non-linearity) and proposes five corresponding control structures. The performance of the proposed control structure candidates is evaluated in a simulation study and, finally, a full-scale experiment is conducted for the best-performing candidate. The results of this study emphasize the importance of control structure selection. While the most obvious control structures failed to deliver the desired performance, the best result was achieved by using control structures that eliminate the conveyor transport delay (dead-time) from the control loop. In practice, the control loop dead-time can be eliminated by either using an actuator (variable-speed feed conveyor) that is connected directly to the feed-hopper, or by redefining the process boundaries closer to the used actuator (regulate the circuit mass balance instead of feed-hopper level). The presented control structures provide means to achieve a consistent cone crusher performance and size reduction. This facilitates efforts to improve the plant’s performance and increases the plant’s overall stability."

Jan 1, 2014

By Carlos Rabanal, Levi Guzmán

"The concern regarding grinding media consumption rates is as old as the invention of the tumbling mill. Over the years many materials and grinding media shapes have been tested. Through all this, steel grinding balls have proved to be the most effective media for comminution in tumbling mills. There have been several approaches to be able to the wear of the ball charge in any given mill, all of them based on limited empirical evidence. The mining industry still utilizes the Bond Abrasion test that was developed in the 1960´s. As shown later in this publication, this approach shows error greater than 60%. More recently, in 2007, Radziszewski from Mc Gill University has proposed a different total grinding media wear model; this model is based on decoupling the effects of the abrasion, corrosion and impact wear mechanisms. Also in 2007, Benavente, at the time with Moly-Cop Peru, presented an empirical model relating both ore properties and operational conditions that would affect the wear performance of the grinding media. For the database referred in this article, Benavente’s model shows an average error of ± 12% which represents a higher degree of improvement in comparison with previous approaches. The current paper presents recent research conducted by Moly-Cop Peru to further improve the capability of the empirical model originally developed by Benavente to estimate grinding media wear rates. The work performed included extensive determinations of the Bond Abrasion Index for different types of ores, collected at industrial grinding applications where the corresponding operational information was made available. The results of the research enabled us to build a more robust and confident model for estimating the grinding media wear rate. The average error of this new model is in the order of ± 9% which is a significant improvement over the models previously described."

Jan 1, 2014

By R. K. Dwari

The electrostatic beneficiation of coal is based on tribocharging characteristics of ash forming minerals and coal particles. The tribocharging of quartz, pyrite and coal particles contacted with various metals and polymeric materials have been measured and the charge acquisition is assessed through surface energy calculations from liquid contact angle data. The contact angles, before and after tribocharging of solids, are measured using Krüss tensiometer and Washburn?s method where the sample holders in tensiometer are specially constructed with tribocharger materials. The charge polarity and amount of charge acquired by quartz, pyrite and carbon with metal tribochargers were found in good agreement with the reported work functions of the contacting surfaces. The charge results with polymer materials differed from the work function values, presumably caused by surface contamination. The surface energy of quartz calculated by all the theoretical approaches in the literature showed that the tribocharging increases the surface energy. Both polar and non-polar components computed from Fowkes and Owens-Wendt-Rabel-Kaelble approaches dis-play that both these components increased after triboelectrification. However, the polar component divided into acid and base components, as in van Oss approach, manifest decreasing acid part and increasing base part. Since quartz charged negatively during tribocharging with metal surfaces and therefore accepted electrons, the determined acid and base surface energy components are consistent with charge transfer process. The results also elucidate an explicit correlation between the charges generated by powders and the surface acceptor (acid) and donor (base) electronic states and thereby the work functions. A novel fluidized bed tribocharger was designed and developed with internal baffle system for efficient contact electrification of mineral and maceral to produce high differential charging for efficient separation. The results achieved on coal with 45% ash content are presented and discussed.

Jan 1, 2014

By S. Cagirici, Z. Öztürk, A. Hassanzadeh

Many flotation kinetics models have been studied in the literature. Their applicability was extensively investigated and argued in detail. However, model selection criteria were not adequately discussed from the statistical points of view. In this investigation, the kinetic behavior of a complex copper sulfide ore was studied in a mechanical Denver flotation cell focusing on flotation kinetics of chalcopyrite, pyrite and molybdenite. Different flotation kinetics models including nine common empirical models and four mathematical models namely Hill, Chapman (Sigmodial function), single rectangular (Hyperbola equation) and exponential were applied to the experimental data. In addition to assessment of the goodness of fit criterion for each model, a factor of model complexity was considered using information criteria (IC) (i.e. Bayesian information (BIC), low of iterated logarithm (LILC) and Akaike information (AIC) indices). The obtained results showed that the IC indices could simply manifest the best-fitted model to the experimental data. Whereas, the coefficient of determination values (R2) were relatively same for all models. By taking the R2 and model complexity criteria into account, the exponential model was chosen as the best representative mathematical model to demonstrate chalcopyrite kinetic behavior. However, Chapman model was selected as the best one for the flotation of pyrite and molybdenite. In case of the common first-order flotation kinetics models, fast and slow flotation kinetic model (Kelsall) was reasonably fitted the best to the given data of chalcopyrite. However, the gas/solid kinetics adsorption model was chosen as the best-fitted one for pyrite and molybdenite. Furthermore, it was found that mathematical models represent better results in association with flotation kinetic behavior of chalcopyrite, pyrite and molybdenite due to the consideration of more parameters in modeling. Finally, it was concluded that the IC indices must be applied to the process of model selection due to consideration of goodness of fit, complexity of a model and model consistency.

Jan 1, 2018

By Alireza Javadi Nooshabadi, Kota Hanumantha Rao

Formation of hydrogen peroxide (H2O2), an oxidizing agent stronger than oxygen, by sulphide minerals during grinding was examined. It was found that pyrite (FeS2), chalcopyrite (CuFeS2), sphalerite ((Zn, Fe) S), and galena (PbS) generated H2O2 in pulp liquid during wet grinding and also when the freshly ground solids are placed in water immediately after dry grinding. Pyrite produced more H2O2 than other minerals and the order of H2O2 production by the minerals was found to be pyrite > chalcopyrite > sphalerite > galena. The pH of the water influenced the extent of hydrogen peroxide formation with greater amounts of H2O2 produced at highly acidic pH. Furthermore, the effect of mixed sulphide minerals, i.e., pyrite-chalcopyrite, pyrite-galena, chalcopyrite-galena and sphalerite-pyrite, sphalerite-chalcopyrite and sphalerite-galena on the formation of H2O2 showed increasing H2O2 formation with increasing pyrite fraction. There is clear correlation of the amount of H2O2 production with the rest potential of the sulphide minerals; the greater the rest potential of a mineral the greater the formation of H2O2. This study highlights the necessity of revisiting the electrochemical and/or galvanic interactions between sulphide minerals, and interaction mechanisms between pyrite and other sulphide minerals in terms of their flotation behavior in the context of inevitable H2O2 existence in the pulp liquid.

Jan 1, 2014

By I Brum

Brazil and Colombia have large reserves of coal, those reserves in Brazil are located predominantly in the south and Colombia the main reserves are located in the north. Despite the relative ease of exploitation, these resources have been underestimated as a source of energy. Currently, these countries are developing projects and partnerships aiming to qualify this mineral resource, adding quality to the final product of the processing plants. In this scenario the processing of Brazilian and Colombian coal in flotation columns appears as a promising alternative, having been successful in mineral systems containing fine particles This paper aims to study the overall process of column flotation for a specific Brazilian coal and a specific Colombian coal. The material used in this study consists of fine coal from Brazil (Copelmi) and Colombia (Cerrejon). The objective is to recover carbonaceous matter and reduce the ash and contaminants grade. The two coals were floated using a negative bias in a 5 cm diameter conventional flotation column of 5 m high. Flotation parameter investigated included air velocity in the range 0.6 to 1.5 cm/s. For all runs, a constant negative bias of -0.25 cm/s and a pulp concentration of 8% w/w were used. For Cerrejón coal, 300 g/ton of frother and 907 g/ton of collector was used, whereas for Copelmi coal, 600 g/ton of frother and 1815 g/ton of collector was employed. The frother was a commercial Aerofroth 65 (AF65), whereas the collector was Kerosene. For the Colombian coal, in general, yield, organic recovery, ash recovery and water recovery decreased with the increasing air rate. However, for Brazilian coal the air rate had no significant effect. For Colombian coal, the highest yield (60% w/w) and organic recovery (69% w/w) were obtained at the lowest air rate (0,6 cm/s). Keywords: negative bias, column flotation, coal

Sep 1, 2012

By L. G. Wang

The stability of foams and froth plays an important role in flotation, in which small amounts of relatively weak non-ionic surfactants (frothers) are used to produce air bubbles and foams. In the present work, factors affecting the stability of the foams produced in the presence of common frothers, such as n-pentanol, n-octanol, methyl isobutyl carbinol (MIBC), and polypropylene glycol (PPG), have been studied. We used the thin film pressure balance (TFPB) technique of Schelud-ko-Exerowa type to measure the equilibrium film thicknesses. The results were used to determine the contributions from the various surface forces to the disjoining pressures in the thin lamellae (foam) films formed between air bubbles. In addition, we used a model developed by Wang and Yoon (Colloids and Surfaces A: Physicochem. Eng. Aspects, 2006) to calculate the elasticities of the lamellae films at the critical thicknesses at which films rupture. The surface forces and elasticity da-ta were then compared with the foam stabilities in the presence of the various flotation frothers. It was found that foam stabilities are controlled by both film elasticity and surface forces, the relative contributions of which change with frother type and concentration. In general, surface forces play a more important role at relatively low frother concentrations, while elasticity plays a more important role at higher concentrations. At the frother additions usually employed in the mining industry, MIBC relies on surface forces while PPG-400 relies on film elasticity in producing stable foams. The former is capable of dampening the hydrophobic force, which is a major attractive force destabilizing lamellae films, while the latter is capable of reducing surface tensions at low concentrations.

Jan 1, 2014

By Y. H. Zhang

Mechanism of BK501 in desiliconization from bauxite was studied by use of flotation test, EDS, ?-potential, FTIR. Results of flotation show that almost all of diaspore can be depressed when BK501 is put into pulp ranging from pH 4~12, in the meanwhile kaolinite is slightly activated. In the light of surface analyses, it is concluded that the adsorption of reagent on the diaspore is dominant by chemical interaction. Moreover, kaolinite may float more by addition of BK501 because of flocculation.

Jan 1, 2014

By Robert van Hille, Alison Lewis

The precipitation of a selection of metals from both a synthetic and an actual metal-rich effluent was investigated. The experimental aspects of this study were carried out in a two-stage process consisting of a pre-treatment clarifier and a fluidised bed (pellet) reactor. Each unit operation in the two-stage process was investigated separately. The pre-treatment clarification stage at pH ˜ 5 resulted in a 99.9% removal of iron and 97.3% removal of aluminium. The pellet reactor was used to precipitate nickel as nickel carbonate from a pure stream and a removal efficiency of 99.6% was achieved. The high local supersaturation at the reagent inlet points caused the formation of a large amount of fines, but these agglomerated onto the pellets up the length of the bed. For copper precipitated as copper sulphide from a pure stream, a maximum removal efficiency of 92% was achieved. The high local supersaturation at the reagent inlets also caused the formation of a large amount of fines, but the extremely sparingly soluble nature of copper sulphide meant that the fines were not agglomerated up the length of the bed. For removal of cobalt as cobalt carbonate from an actual stream, a stable cobalt removal of only 60% was achieved. This was found to be due to the presence of magnesium, which reduced the cobalt precipitation efficiency through the formation of the magnesium bicarbonate ion.

Jan 1, 2003

By Heinrich Hutchison, Thomas von Moltke, Roelof F. Sandenbergh, Katarina P. Cerovic

In the leaching of gold in aqueous cyanide solutions the rate of gold leaching may be decreased by the passivation of the gold, that may however be prevented or reversed in the presence of lead species in solution. In the present study potentiostatic, potentiodyanamic and XPS (X-ray photoelectron spectroscopy) analysis were used to further clarify the action of lead ions on the anodic activity of gold in alkaline cyanide solutions. It was found that lead increased the gold dissolution rate as it deposited on the gold surface at potentials more positive than its reversible Nernst potential for bulk metal deposition, i.e. by underpotential deposition mechanism, but that it decreased gold activity if present as bulk plated lead on the gold.

Jan 1, 2003

By A. L. Hinde

The steady-state and dynamic behaviour of semi-autogenous grinding (SAG) mills are arguably best described using a population model that caters for the breakage kinetics and the material trans-port of rock and pulp inside the mill. Breakage kinetics are usually expressed in terms of a specific breakage rate function and a separate primary breakage distribution function. Material transport usually invokes the concept of a specific discharge rate function. Unfortunately, the breakage rate and breakage distribution functions for SAG mills are very difficult to estimate uniquely from plant data alone. Simplifying assumptions must be made to over-come this problem, which leads to many unresolved dilemmas with regard to whether or not the de-rived functions are accurate, precise, and reflect reality. For example, it is sometimes assumed that the breakage distribution function for a SAG mill treating run-of-mine ore can be derived from laboratory dropweight and tumbling tests on small rocks in narrow size ranges. Such tests hardly reflect the environmental conditions likely to be encountered in a pilot or production SAG mill where there is a wide spectrum of particle sizes. It is shown that the dilemmas associated with standard population balance models (models that utilise separate breakage rate and breakage distribution functions) can be overcome by expressing breakage behaviour inside a SAG mill in terms of a single function. This function is an energy-based cumulative breakage rate function defined as the fractional rate at which particles and rocks coarser than a given size break to below that size per unit specific energy input. A model for SAG milling is formulated, which invokes the concept of a cumulative breakage rate function. Comparisons are made between the mathematical structure of this ?simple model? and standard population balance models. Perhaps the most attractive feature of the ?simple model? is that the cumulative breakage rate function can be uniquely estimated from measurements of size distributions and mass flows of the feed and discharge streams together with the size distribution and holdup mass of the mill charge. Such measurement can easily be made at pilot scale. It is concluded that this simplified approach to SAG milling may turn out to be the quickest way to fully describe and quantify the performance of these very complex mills.

Jan 1, 2014

By H. Wotruba, L. Gronen, A. Hellmann, S. Sindern, J. Katzmarzyk

"This paper focuses on the beneficiation of the REE-Y-Nb-Zr complex ore from the ‘Khalzan Buregtei’ deposit, Mongolia. Pre-concentration based on mineralogical studies was investigated at the Unit of Mineral Processing (AMR) and the Institute of Applied Mineralogy and Economic Geology of RWTH Aachen University. In order to minimize the energy consumption in the most energy intensive grinding process a pre-concentration process using dry magnetic separation of particle sizes coarser than required for the liberation of the valuable ore minerals was designed. Dry magnetic separation in the particle size range of 63-250 µm is suitable as the pre-concentration method, due to the intergrowth of REE-Y-Nb-Zr bearing minerals with magnetic minerals determined by QEMSCAN© analysis. The results showed that a mass reduction of 45.3 wt.-% at high recoveries of REE, Y, Nb and Zr (90 wt.-% and higher) in the pre-concentration product was achieved at the beginning of the process chain. The improvement of process efficiency as shown in this study depends on the abundance and association of minerals affecting the magnetic properties (e.g. hematite) of the ores. Therefore, these mineralogical parameters are as important as grain size and ore grade for the geometallurgical evaluation of potential mining operations at ‘Khalzan Buregtei’.INTRODUCTION Polymetallic deposits containing other critical elements besides REE have the advantage of being robust to economic development and fluctuations of individual metal prices. (Gronen et al., 2016). These deposits can host economic grades of heavy and light REE, Y, Nb, Ta, Zr in complex mineralogical compositions. About 120 deposits of this type are known worldwide, including ‘Norra Kärr’ in Sweden, ‘Strange Lake’ in Canada and ‘Khalzan Buregtei’ in Mongolia which are not valued economically yet. (Salvi. & Williams-Jones, 2004.)"

Jan 1, 2018