Search Documents

By Alim Gül, Güven Önal

"Recently, there have been some attemps on the treatment of low grade ores and old plant tailings due to the decrease in high grade ores and the increase in the metal consumption with increasing world population. Cost of mining and beneficiation of low grade ores become prohibitive since the costs of grinding before flotation make the process unfeasable. Therefore, preconcentration of these ores prior to flotation becomes more important. The concentration of ores preconcentrated in coarse sizes provides a decrease in investment costs as well as grinding and flotation costs. Additionally, the requirements of less space for tailing disposal and less reagent consumption are also important from the viewpoint of environmental considerations.In this study, ore sample containing 0.6 % Cu and taken from Küre-Asiköy ore body was used. Ores contained chalcopyrite and pyrite as main minerals and diabaz, quartz, chlorite and sericite as gang minerals.Samples were all crushed under 9 mm by considering the preliminary studies and float and sink experiments were carried out with the sample in the size range of –9+1 mm using different densities of heavy liquids. As a result of these tests, it was shown that 60 % of the material should be discarded as tailings with 0.1 % Cu content. By considering float and sink test results, the following experiments were performed by using heavy medium cyclone and jigs.As a result of heavy medium cyclone tests, which are conducted on the sample in size range of –9+1 mm, 57 % of the feed material was discarded as tailing with 0.08 % Cu content and 7 % Cu loss, while a concentrate containing 1.43 % Cu was produced with 93 % efficiency (Table 1). Jig tests were done with the samples in the size range. As a result of jig tests with –9+1 mm size group sample, approximately 46 % of feed material was discarded as tailings with 0.13 % Cu content and 10.6 % Cu loss, while a concentrate with 0.94 % Cu content was obtained (Table 2)."

Jan 1, 2003

By Valentine Chanturiya1

We have developed a classification of geochemical barriers according to their origin, i.e. natural and artificial, and according to methods and areas of application. There has been an examination of the interaction between different classes of geochemical barriers with sulfate solutions containing nickel, copper and iron. As natural barriers, carbonates (calcite and dolomites) were used. For artificial barriers, a mixture of serpentine and carbonatite, thermo-activated copper-nickel dressing tailings, and a magnesium-containing sorbent based on brucite was used. Keywords: geochemical barriers, physical-chemical geotechnologies, treatment of natural and waste water, recovery of nonferrous metals

Sep 1, 2012

By Sanjay Agarwal

Polymetallic sea nodule is a good source of manganese having 22.3% Mn, 5.4% Fe, 6.14% Si, 1.1% Cu, 1.15% Ni, 0.076% Co & others. These nodules are available in plenty on the sea beds, generated over thousands of years. Nodules mainly consist of manganese dioxide and iron oxide phases and other metals are entrapped in the complex cage of these Mn-Fe oxides phases.World-wide research is going on sea nodules as an alternative future source of many metals, which has led to intensified efforts to develop practical and economical processes for recovery of these metals. Very little attempt has been made world over on manganese extraction from sea nodules. We at CSIR-NML, India have developed a direct reduction smelting process of nodules to recover manganese as Fe-Si-Mn alloy. This alloy is extensively used in the steel industry as deoxidizer and as an alloying element to make different grades of steel. Lab scale experiments were conducted to study the manganese distribution between Fe-Si-Mn alloy and FeO-SiO2-MnO-CaO-Al2O3-MgO slag at different temperatures by varying the basicity of the slag. The direct reduction smelting of nodules is carried out on 1 kg scale in 50 kVA electric arc furnaces to have Cu, Ni and Co alloy and Mn rich slag. This manganese rich slag is further treated in 50 kVA arc furnace to produce Fe-Si-Mn alloy. The composition of Fe-Si-Mn alloy obtained is in the range of Mn: 60-65%, Si: 14-17%, C: 1- 2%, S: 0.03% and the balance iron which is acceptable grade for industrial use. The equilibrium amount of MnO in the final slag is controlled by the temperature of the final melt and the silica, lime, alumina content of the final slag. Increasing the basicity of the slag plays a major role in minimizing the loss of MnO to slag, increasing the amount of SiO2 of the slag, increases the manganese loss in the slag. Increasing the CaO/ Al2O3 ratio of the slag decreases the manganese loss in the slag. Increasing the MgO/CaO ratio of the slag increases the manganese loss in the slag. Thus by adjusting

Sep 1, 2012

By S. Banisi, Seyyed Omid Mousavi, Alireza Ghasemi

Discrete Element Method (DEM) is extensively used to simulate the behaviour of particles in various processing units. This method is based on modelling the forces acting between particles in any contact and consequently calculating the new position of particles. The high number of elements and numerous equations needed have made the required computation time very long even using computers with very fast processors. The required computation time mainly depends on the time step. If the time step is chosen very short, the computation time will significantly increase. On the other hand, if the time step is chosen very long, the simulation will be in error due to not fully observing the contacts. In DEM calculations, the time step is chosen as a fraction of the collision time. In this research, a relationship was proposed between the contact time fraction and the error of simulation. In other words, to select the time step in addition to physical parameters, the accuracy of the simulation was also accommodated in the frequently-used relationships. The simulation error was defined as the relative difference between the initial restitution coefficient and the restitution coefficient obtained after simulation. The required time steps to arrive at the simulation error of 5% were calculated for two common contact force models namely, Hertz-Mindlin and linear spring-dashpot. The simulation was performed for two particles with radius of 3 cm, elasticity modulus of 210 GPa, Poisson's ratio of 0.3 and relative velocity of 0.5 m/s. The required time steps were found to be 2.3 and 0.19 µs for the Hertz-Mindlin and the linear spring-dashpot contact force models, respectively. Results showed that with a scaling-down the modulus from 210 GPa to 2.1 MPa, the required time steps for the Hertz-Mindlin and the linear spring-dashpot contact force models, with an equal simulation error, increased by 100 and 316 times, respectively.

Jan 1, 2014

By D. Endara, E. De la Torre, S. Echeverria

"The study was conducted with the sulfide mineral from the province of Zamora Chinchipe. It was characterized physical, chemical and mineralogical, obtaining between its main results a copper concentration of head ore of 0,58 %. The mineral was homogenized and taken to direct closed circuit: rollers mill - vibratory sieve (mesh # 16). Flotation was carried out in two stages: the collective and selective where in each one were performed 6 water recirculation as suggested by the technique used to relate information of a batch flotation to a continuous circuit called cyclic flotation tests (LCT). In the collective flotation (bulk) 2 Kg of mineral were grinded with 10 Kg of balls for 30 minutes and 62.5% of solids, the pulp was taken to the flotation process with solids percentages of 33.3% and pH 7, it was conditioned with 45 g / t of KAX 1%, 50 g/t of Aerofloat 208 and 20 g /t of Pine oil. The concentrate and tailings bulk obtained were filtered separately for the recovery of water and it was recirculated to the next grinding of 2kg mineral. In the selective flotation 1Kg of bulk concentrate was carried to regrind for 40 min, 62.5% percent of solids, 10 g of lime and 5 g of tannin FLOATAN T5, the pulp was taken to the roughing-collection-refining flotation circuit controlling the pH between 10.5 and 11 where conditioning (60 g/t of Aerofloat 208 and 30 g/t of Pine oil) and adding lime to the circuit and FLOATAN according to the procedure. The four fractions obtained from the circuit were filtered; the water was recirculated to the regrind process of the bulk concentrate. In the collective flotation process tends to stability in the fourth recirculating water to obtain a copper content of 4.5% and a recovery of 87%, recirculated water represents 69.8% of all water used in the 6 recycles. In the selective flotation circuit the fifth recirculating of water is the optimal where obtaining a copper content of 13% and a recovery of 72%, recirculated water in the selective flotation circuit represents 95% of the total water used in the 6 recycles."

Jan 1, 2018

By S. V. Balikov

A close association of fine gold with pyrite and arsenopyrite is observed at many gold ore deposits. Gold forms and gold distribution in sulfides of different deposits were studied. A comprehensive method including optical spectrum analysis, X-ray diffraction analysis, high-temperature X-ray diffraction analysis, scanning electron microscopy and X-ray microanalysis was used for the de-tailed investigation of the defectiveness of the structure of pyrites from different deposits. It was shown that gold content in pyrites varied from 1.5 g/t to 100 g/t compared with 30 g/t to 230 g/t in arsenopyrites. The nature and arrangement of inner inclusions of foreign minerals in pyrites as well as occurrence of fractures and macro- and microdefects were examined. Iron, sulfur and arsenic contents in all pyrite samples were determined. Chemical composition of the detected inclusions was defined. Parameters of submicroscopic structure of pyrite were estimated using X-ray Fourier line shape analysis. Estimation of real structure characteristics with calculation of submicroscopic D-blocks and root-mean-square lattice deformation 2()evalues was performed. Defectiveness of the pyrite structure can be defined by the following parameters: K?1 and K?2 reflection resolution and its intensity within high Bragg angles; S content to Fe content ratio; the arsenic content and the local variation in its concentration within the pyrite grain; the size of submicroscopic blocks and the crystal lattice disturbance value. The performed analysis showed some relationships between these parameters and refractoriness of the pyrite concentrates. It was observed that at S/Fe ratio close to or higher than stoichiometry and at a low arsenic content (less than one per cent) pyrite concentrates were not refractory. The analysis results showed that concentrates of the Beryozovskaya gold plant (0.02~0.07 As%) and concentrates of the Kommunarovskaya gold plant (less than 0.05 As%) as well as some pyrites from the Sukhoi Log gold deposit had the same characteristics. It was found that average arsenic content did not excess 0.2 per cent. Arsenic distribution within the grain of all these pyrites was uniform. At S/Fe ratio lower than or close to stoichiometry and at high arsenic content (more than one per cent) and significant variation in its distribution within a pyrite grain the pyrite concentrates are refractory. Such pyrites are typical for the Sukhoi Log, the Bakyrchik and the Mardzhanbulak gold deposits. Direct correlation between arsenic and gold contents, in particular, in fine grains of pyrite was observed by many researches. This correlation was explained by impregnation of arsenopyrite which normally contains more gold than arsenic pyrites. The analyses results showed that no arsenopyrite impregnation was found: arsenic distribution within the grain was uniform but its concentration varied greatly. Such pyrite concentrates are more refractory. This paper presents the results of analyses of sulfides to determine the amenability of the associated gold recovery by hydro- and pyrometallurgy.

Jan 1, 2014

By G. R. Forbes

Flotation froth machine vision systems provide consistent real-time measurements pertaining to the state of the flotation cell being monitored. Typical measurements include froth velocity, froth colour, froth texture and froth stability. This paper presents the results from test work conducted on the molybdenite rougher circuit at the Kennecott Utah Copper Concentrator during February 2006. Machine vision results show that it is not possible to accurately determine bubble size distribution information for the molybdenite froth, despite using state-of-the-art methods. Instead, it is necessary to make use of texture measurements to classify the various different froth states. Numerous combinations of texture measurements and classifiers are used to determine the best combination. Results show that the Fourier ring based texture measurements perform the best when both K nearest neighbour and Gaussian mixture model classifiers are used. The concentrate grade of the flotation cell is modelled using combinations of froth velocity and froth texture descriptors. The results show that by using a linear combination of these descriptors rather than either one by itself it is possible to account for a much larger percentage of the variation observed in the concentrate grade data. Adjusted R2 values of 92% and 84% are achieved when modelling the copper and the molybdenite concentrate grade respectively.

Jan 1, 2014

By G. F. Zhang

Yunnan mineral is a kind of containing Ta-Nb rare earth deposit, the most potential economic valuable element in it is Sc, and raw mineral has 17.0 g/t Sc. Take the character of Sc into account, the key problem in producing scandium chloride molten salt by adaptive technology is how to man-ufacturer anhydrous scandium chloride molten salt. During the course above, the key problem is that preventing Scandium chloride from being hy-drolyzed into ScOCl. The ScOCl content of molten salt not only affect purifying scandium but al-so do harm to the production of Mg-Al alloy. In order to restrain the creation of ScOCl, add ammo-nium chloride into molten salt. As long as ScOCl is created, it would be chloridized. Thus, during the course of dehydrating anhydrous chloride molten salt this method prevents scandium from hydrolyzing. Accordingly, the key phase of this producing course is eliminate ammonium chloride and the surplus crystal water, and the most crucial of it is restrain scandium chloride from being hydrolyzed into ScOCl. This research analyzed the theory that ammonium chloride is trend to be hydrolyzed into ammo-nium chloride, and propose the research scheme of restraining this process from creating ScOCl. The new process of restraining the generating of ScOCl and dehydration for crystal water rare earth chloride is adopted: Inert gas temperature increases rapidly to a certain degree to eliminate ammonium chloride and crystal water. The experimental research were done such as : the temperature of eliminating ammonium chloride and crystal water, amount of ammonium chloride, time, temperature growth speed, influence of inert gas flow toward to scandium percent hydrolysis, whereby, we conclude the optimal process condition in this period: Temperature: 400°C, proportion of oxidized scandium and ammonium chloride is 1:1.5(Proportion of oxidized scandium and additional salt is 1:5.4), time is 120minute, temperature growth speed is 10?/min inert gas flow is 5L/min.

Jan 1, 2014

By I. Nishkov, I. Grigorova, N. Valkanov, M. Ranchev

The processing of sulphide ores with variable and complex mineral composition and physical properties, such as those processed by two-stage selective flotation scheme in “Erma reka” concentrator, Minstroy Holding JSC, requires excellent selectivity in order to achieve acceptable concentrate grades. The lead-zinc ores from the hydrothermal lead-zinc deposits mainly contain galena (PbS), sphalerite (ZnS), pyrite (FeS) and chalcopyrite (CuFeS2), as well as non-metal minerals such as quartz, carbonates and clinopyroxenes skarns. One of the main impurities present in sphalerite is iron, which is known to be detrimental to the rate of sphalerite flotation and its recovery. The results from the conducted laboratory and industrial tests, presented in the previous study, showed that it is possible to depress the iron rich sphalerite by adding MINFIT® (modified sulfur-oxy depressant) at the pH of approximately 9.5 in rougher lead flotation circuit, leading to reduction of zinc sulphate consumption and complete elimination of cyanides from the flotation process. Furthermore, the consumption of copper sulphate, which reactivates the surface of the zinc minerals, was significantly reduced. Consequently, the optimisation of the reagent regime in the Erma reka concentrator, led to notably improved qualitative (grade, recovery) properties of the final lead and zinc concentrates. Moreover, when comparing the reagents consumption for 2014 and 2016 – when the processing plant have been applying the new optimized reagents regime, comprises the use of MINFIT as the primary depressant, the following results have been achieved: ZnSO4 decreased by 30%; CuSO4 consumption decreased four times and full rejection of cyanides from the process. Finally, this paper provides a state-of-the-art review of the obtained results during the period of application of the new flotation reagents regime in the Erma reka concentrator, Minstroy Holding JSC.

Jan 1, 2018

By T. Laxmi

This paper details the optimization of rougher Wet High Intensity Magnetic Separator (WHIMS) using response surface methodology. The optimization is in parametric form and takes account of the major operating variables in WHIMS operation such as current in ampere and grid gap, in inch. The objective is to recover ilmenite mineral from red sediment deposits of Srikakulam, India by optimizing the rougher WHIMS. We predict mineral recoveries as a function of current and grid gap. Combination of these predictions with assay data provides predictions of mineral grades and recoveries. The optimized response was validated against data derived from laboratory-scale rougher WHIMS test work, comprising (i) mineral grade, (ii) mineral recovery, and (iii) separation efficiency of the process. We observed close match between the experimental and the predicted data over most of the operational range. This paper describes how the optimization was carried out using the response surface methodology along with MATLAB. The response surface was used to closely investigate the separation of ilmenite mineral by varying ampere and grid gap. The results show that under optimum conditions, such as 3.5 amp current (0.53 Tesla) and 2 inch grid gap, the mineral grade could reach, as high as 87.9% in the concentrate with 74.3 % recovery and 74.4% yield. Keywords: red sediment, wet high intensity magnetic separator, optimization, ilmenite, placer heavy minerals

Sep 1, 2012

By A. Pandey

Over the years, Coal Beneficiation at Tata Steel - West Bokaro has seen varied changes. With increasing R.O.M throughputs & lowering of the concentrate ash, Fine Coal Beneficiation process has thrown up myriad challenges. Development of Synthetic Collector was initiated couple of years back with Technical assistance from NLC Nalco India Ltd. Coal from West Bokaro unit was sent to Nalco?s Naperville (US) research lab for developing Tailor made synthetic collector . After comprehensive lab flotation studies, synthetic collector was developed & recommended for plant evaluation. The lab scale results were very promising in terms of improved separation efficiency & yield at similar ash level. The collector sample received from Nalco research laboratory were revalidated at Nalco Kolkata lab and finally at Tata Steel West Bokaro lab, confirming the promising results. (S.E 25-30 % better than HS Diesel) The key factors playing out for this improvement initiative are a) Scope for improvement in Clean Coal Yield at same or lower ash level coupled with improved Selectivity and Separation Efficiency b) Introduction of a Synthetic Collector with a Green Chemistry and subsequent replacement of H S Diesel, which is highly inflammable with a less inflammable & safer product Trial was conducted at plant scale in two phases and comparative performance of the Collector vis-à-vis Diesel was evaluated across the following Coal Seams of Q- SE (Seam VII, VIII, VI, IX and X). The results generated are very promising and the improvements observed are summarized below. ? Separation efficiency improvement by more than 20% observed. ? Flotation Fines yield increase varied from 0.6- 1.5 % on raw coal basis across different seams. ? Consumption pattern is 20-25 % lower than Diesel. Keywords: synthetic collector, west bokaro, coal beneficiation, HSD

Sep 1, 2012

By Ernesto de la Torre, Karla Velín, Alicia Guevara

"The following study shows the improvement and simulation of a gold recovery plant of 24 t/day of capacity by gravity concentration, flotation and leaching. The ore processed had grades of 6 g/t Au, 15 g/t Ag, and 0.69 %Cu with the mineralogy consisting of 2 %chalcopyrite, 12 %pyrrhotite, 7 %plagioclase and 50 %quartz. The recovery process starts with crushing the ore followed by grinding it further in a ball mill. The ground ore is then concentrated in a Falcon centrifugal concentrator with concentrate being processed by amalgamation process. Gravity tails are sent to a flotation circuit where the copper minerals and some gold are concentrated. Lastly, the flotation tailings undergo cyanidation for gold recovery. Currently, the overall recoveries are 82.8 %Au, 49.6 %Ag and 99.1 % Cu. The optimization was developed in the laboratory using a Wilfley table by gravity concentration. Flotation tests in the laboratory were performed using potassium amyl xanthate and pine oil. Lastly, cyanidation was then performed on the flotation tailings. The results showed the optimum concentration of sodium cyanide in cyanidation is 2 g/L, which produced an increase in gold recovery from 30% to 44%. The reduction of diameter particle from 132 to 80 µm also produces an incremental recovery of gold and silver from 11% to 21% Au and 0.4 to 3% Ag in gravity concentration. Likewise in the cyanidation the recovery of gold and silver has shown a rise from 44 to 62% and 8 to 32% for Au and Ag respectively. However, the flotation method the gold recovery is reduced from 68 to 30% Au by reducing the particle size. Computer simulations using the programs, Moly-Cop and ModSim were performed to determine optimum parameters for the recovery of precious metals at the gold recovery plant."

Jan 1, 2014

By S. Carsten, S. Subramanian, R. Vasant Kumar, S. Vimalnath

"The effect of EPS components namely protein, polysaccharide and biosurfactant purified from Pseudomonas fluorescens was investigated for the bioremediation of Pb(II) ions in aqueous solution. Two parameters, namely the amount of EPS component and the concentration of Pb(II) ions were optimized for maximum Pb(II) ions uptake. The EPS components interacted with Pb(II) ions were characterized using energy dispersive X-ray analysis (EDAX) to ascertain the presence of Pb and by attenuated total reflection-Fourier transform infrared spectroscopy (ATR–FTIR) to reveal the functional groups involved in Pb(II) binding. The maximum Pb(II) binding capacities of protein, polysaccharide and biosurfactant were found to be 11.4, 0.55 and 0.11 mg mg-1 respectively. The biosorption processes followed the Langmuir model. The Gibbs free energy (?G0) values of -23.6, -20.9 and -23.2 kJ mol-1 for Pb(II) biosorption by protein, polysaccharide and biosurfactant respectively, attested to spontaneous, chemisorption processes. The ATR–FTIR results revealed the presence and involvement of amino, hydroxyl, carboxyl, phosphate, and methyl functional groups in Pb(II) binding and EDAX analysis confirmed the interaction of Pb with EPS components. The Pb(II) binding mechanisms of EPS have been discussed. The results demonstrate the potential of the purified EPS components of P. fluorescens for removal of Pb(II) ions from aqueous solution INTRODUCTION Waste water containing toxic metals from various industries pose a serious threat to human health and ecosystem. For treating such waste water, conventional methods like chemical precipitation, coagulation, evaporative recovery, electrodialysis, floatation, flocculation, ion exchange, reverse osmosis, nanofiltration, ultrafiltration are used (Lakherwal et al., 2014). These methods have some disadvantages like toxic sludge generation, incomplete metal removal and high cost (Singh and Gadi, 2012), necessitating the search for cheaper and efficient alternative methods. Bioremediation is one of the emerging alternatives where bacteria, fungi, yeast, algae and other biological substances are used as sorbents to remove toxic heavy metals (Vijayaraghavan, et al., 2015). Recently, the bioremediation potential of extracellular polymeric substances (EPS) of microbial origin has attracted attention. However, for Pb(II) removal, there is a paucity of literature focusing on EPS."

Jan 1, 2018

By S. K. Sharma, R. Markandeya, G. Venkateswara

"In this study, a three level Box- Behnken factorial design combined with Response surface methodology (RSM) for modeling of process parameters of Multi Gravity Separator (MGS) for recovery Iron values from sub grade iron ore, Deposit No. 5, Bailadila complex has been developed. The three significant operational parameters of MGS, Drum rotational speed (RPM), Drum inclination (degrees) and quantity of wash water (LPM) were considered in the experimental work. Other parameters like feed percent solids, shake frequency and shake amplitude were maintained constant. The ‘as received’ sub grade iron ore sample is admixture of lump and fines and chemically assayed 40.80% Fe, 40.90% SiO2, 0.24% Al2O3 and 0.22% Loss on Ignition (LOI). The obtained results were evaluated with the Box-Behnken factorial design, RSM and also Quadratic programming(QP). Second order response functions were produced for Fe in terms of grade (%) and recovery (%) of the concentrate fraction. Taking advantage of QP, it was observed that maximum grade of 62.21% Fe achieved at an inclination of 4.3degrees, 2.7LPM of wash water and at a drum speed of 198 RPM. Similarly a maximum Fe recovery of 65.37% weight can be achieved at 4.3degrees inclination, 2.6LPM wash water and at a rotational speed of 212 RPM Predicted values of responses obtained using model equations were in good agreement with the experimental values. The influence of the process variables of the multi gravity separator concentrator on grade and recovery of concentrate fraction were presented and discussed."

Jan 1, 2014

Producing robust agglomerates with desirable structural properties is the key to success of the heap leaching of complex, low-grade nickel laterite ores. Mechanically strong but porous agglomerates with narrow size distribution (e.g., 5 ? 40 mm) are required to build permeable and perennially stable heaps of 4 ? 10 m height. The characterization of granules? microstructure is essential for greater understanding and correlation with the concomitant mechanical properties and robustness. In this study, we used non-destructive, computed X-Ray tomography analyses and scanning electron microscopy (SEM) in tandem with conventional compressive strength,and integrity/stability tests to draw links between nickel (Ni) laterite agglomerate strength/stability, internal microstructure (e.g.,porosity, inter-particle bridges) and binder type. It is shown that binder composition (e.g., tap water vs. 30% w/w H2SO4) and post-agglomeration drying both significantly impact on granules? physicochemical and microstructural properties. Acidic binder, in contrast with tap water, leads to significant incongruent leaching of different species from particles during ore-binder mixing and agglomeration. Upon wet agglomerate curing, solidified/recrystallized leached species form strong intra-granular solid bridges which, lead to greater compressive strength of dry agglomerates. Structural stability/integrity of cured agglomerates in acidic solution, however, decreases dramatically due to greater porosity and acid solubility of intra-granular solid bridges. These findings are useful in shedding more light on agglomerate structure characteristics and their optimization for enhanced column and heap leaching with concentrated sulphuric acid.

Sep 1, 2012

By R. X. Li

The overall flow-sheet of producing chromium (III) sulfate is described in this paper. The suitable conditions of each process such as sintering, leaching, aluminum removal, reduction, and de-composition conditions were experimentally studied. The results show it is reasonable to produce chromium (III) sulfate with the flow-sheet pointed out in this research work. The final product is Cr2(SO4)3 solution contained 150~250g/L Cr.

Jan 1, 2014

By S. M. Javad Koleini

The aim of this research is to extract zinc from complex lead and zinc ore containing carbo- silicate lead and zinc minerals using sulphuric acid. Samples, taken from Dareh Zanjireh mine located in central of Iran, were subjected to leaching tests after calcination process. Experiments were planed according to the Taguchi statistical method. The calcinated samples contain 13.98% zinc and the constituting minerals being dolomite and zincate. Various parameters such as speed of mixing, temperature, time, solid to liquid ratio and pH were studied. A solid to liquid ratio of 1:6 gr/mL at 60°C and 800 rpm speed of mixing for 30 minutes resulted in a product with 85.96% zinc recoveries.

Jan 1, 2014

By P. Braga, A. Chaves, S. França, A. Luz

"In Brazil, there are no official reserves of molybdenum, and the unofficial reserves are modest. Therefore, the molybdenum ore (molybdenite) produced as a co-product or by-product of emerald mining in the region of Campo Formoso, BA, has arisen as the only economic option. The flotation process is commonly used in Brazil for the recovery of molybdenite from emerald mining tailings, but it produces low-content molybdenite concentrates, thereby resulting in a product with low economic value. The molybdenite concentrate produced in Campo Formoso contains 83.5% MoS2 (50% Mo), which is less than the international standard product that contains > 90% MoS2 (54% Mo).This low value is due to the presence of talc, which is a naturally hydrophobic mineral that is also floated with the molybdenite during the flotation process. Separability studies were done in a Partridge-Smith cell using dextrin and quebracho as a molybdenite depressor in solution at different concentrations and pH values to produce a technical-grade concentrate (i.e., 90% MoS2). These basic studies were accompanied by measurements of the zeta potential and contact angle, which was determined by the capillary rise method. The results of these floatability studies were used in bench flotation tests, which were performed in a Denver laboratory flotation cell. A molybdenite concentrate of 93.4% MoS2 was obtained when dextrin was used at a concentration of 100 g/t."

Jan 1, 2014

By M. E. Taranenko, V. A. Krivonosov, S. A. Nemykin

"In concentrating production energy-consuming power installations are wide used, the most powerful of them are the wet autogenous grinding mill operating in closed circuit with a spiral classifier. The analysis of the current state of the automation of the grinding process shows that the reserves for maximizing productivity and minimizing electricity consumption have not yet been exhausted on the existing process equipment. Usage of the achievements of the modern management theory reveals an opportunity for further optimizing of the grinding process. The purpose of the research is to develop an automated control system of complex ""the mill-classifier"" to conduct the grinding process in the most operating efficiency, ensuring the maximization of productivity and minimization of specific electricity consumption. The main idea of this work is to study the specific features of the ore grinding process and creation on this basis of automated control system complex ""mill-classifier"" which allows to find and to maintain the optimal mode of grinding based on identification of the current object parameters, observance and regulating of the object state coordinates. Research methods. We used the methods of system analysis, mathematical statistics, modern automated control theory, theory of systems identification, optimal control, modelling of dynamic processes. Developed scientific provisions: - identification algorithm of the loading sub-system management object of complex ""mill - classifier"" allowing to obtain the unbiased estimators of its parameters according to the data of normal object exploitation; - observing device, which differs from the classic version of the observer Luenberger with possibility of estimating not only the state coordinates of the control object, but also the low-frequency perturbation component; - automated system stabilizing the active power of the grinding mode on the basis of a states controller with Luenberger observer; - structure of the software and hardware that implements the developed models, algorithms, methods of control, management and optimization in the framework of the automation of grinding."

Jan 1, 2018

By Alexander E. Sobolev

The kinetics of oxidative dissolution of lead sulfide in solutions of nitric acid and sodium hypochlorite was studied using the rotating disk method and the factor experiment design. The dependences of the PbS dissolution rate on concentration of oxidant (HNO3 or NaOCl), temperature, disk rotation frequency, and duration of interaction were determined. The adequate kinetic models allowing calculating the specific dissolution rate at any combination of values of the influencing factors were obtained. As a result of the complex analysis of kinetic parameters, the modes of the each process proceeding were established, their macromechanisms were determined, and the limiting stages of the oxidative dissolution processes were revealed. The dissolution kinetics of lead sulfide in solutions of nitric acid was found to have several regimes. At HNO3 concentrations below 0.5 mol/L, the process proceeds in a mixed mode close to a diffusion-controlled. It is caused by low oxidative activity of HNO3 and considerable diffusional diffuculties at this acid concentration range. At the nitric acid concentrations more than 0.5 mol/L and less than 6.0 mol/L, the process was found to be kinetically controlled. The limiting stage of the interaction is the surface chemical reaction. The observed relatively high order of the dissolution rate with respect to the concentration of HNO3 was explained by the autocatalytic action of the acid reduction products. At nitric acid concentrations exceeding 6 mol/L, the process proceeds in a mixed mode close to a diffusion-controlled, and the dissolution rate sharply decreased that was explained by a decrease in the solubility of reaction products. When lead sulfide is dissolved in sodium hypochlorite solutions, at first time the amount of PbS transferred into solution remains close to zero. Gradually, as time goes, this amount begins to increase sharply. The dissolution rate rises and reaches the maximum value, further remaining constant. At the steady-state regime, the dissolution rate is independent of the duration of interaction and disk rotation frequency. The process was found to be kinetically controlled. The limiting stage is likely to be chemical reaction on the surface of solid lead sulfide. The obtained kinetic characteristics enlarge the database on hydrochemical oxidation kinetics of sulfides and can be used for the elaboration of the recommendations for the effective comprehensive exploitation of lead-bearing ores and concentrates. Keywords: lead sulfide, nitric acid, sodium hypochlorite, hydrochemical oxidation, dissolution kinetics

Sep 1, 2012