Search Documents

By David S. Cronan

Submarine hydrothermal mineralization occurs in at least three locations along the Hellenic Volcanic Arc in the Eastern Mediterranean Sea. Weak hydrothermal discharges occur off Kos and Nisseros at the eastern end of the arc and off Milos at the western end. In both cases the hydrothermal solutions are rich in iron and manganese and are precipitating iron oxides variably enriched in minor elements. This points to the likely presence of sulphide minerals at shallow depth below the sea floor at these locations. By contrast, at Santorini, in the centre of the arc, the hydrothermal discharges are much stronger and rate of deposition of the hydrothermal minerals much greater. Indeed, in one of the two hydrothermally active embayments off Santorini (Nea Kameni) hydrothermal deposits are accumulating up to five times as fast as in the Atlantis II Deep of the Red Sea. Radiocarbon dating indicates that these deposits have been accumulating for about 100 years. In the other embayment off Santorini (Palaea Kameni), hydrothermal deposition has taken place over a longer period (more than 1,000 years) but the deposits are not so hydrothermally enriched due to the simultaneous deposition of biogenic silica and detrital mineral with the hydrothermal deposits. The observed pattern of increasing intensity of submarine hydrother¬mal activity from the extremities of the arc towards its centre argues for additional hydrothermal mineralization on poorly explored areas of the sea floor between Milos and Santorini and between Kos and Santorini.

Jan 1, 1994

By Andrea Koschinsky

Ferromanganese crusts have traditionally been considered a potential ore for Co, whereas ferromanganese nodules have typically been considered a potential ore for Ni and Cu. However, both nodules and crusts sequester high concentrations of many metals (Table 1) from sediment pore waters and seawater, many of which are essential for high-tech applications. The resource potential of these rare and valuable metals is poorly known and they are the subject of considerable current research. The need for adequate and dependable supplies of these metals is essential for the development of new technologies. The rare-earth elements have recently received much attention in the scientific and popular press because of their use in so many high-tech applications and because more than 95% of the production comes from China (e.g., Service 2010); consequently, there is concern about the possibility of a significant decrease or even curtailment in exports from China. The lack of a primary source and the inadequate supply of Te have prohibited the development of a Cd-Te photovoltaic solar-cell industry (Hein et al. 2010). Inadequate supplies of many of the elements listed in Table 1 are limiting the development of key high-tech industries, forcing the use of alternative metals that [ ] may result in less efficiency or less favorable properties for a product. The rare-earth elements, Te, and other elements listed in Table 1 occur in high abundances in marine hydrogenetic and diagenetic ferromanganese deposits. Here, we look at the mechanisms by which these rare and valuable metals are incorporated into different genetic types of marine ferromanganese deposits.

Jan 1, 2010

By Christina Pomee, John Parianos

"TOML’s ISA Contract comprises six areas (A-F) that span from 118° to 152° W and from 7° to 15° N or over 70% of the CCZ.During a 2015 exploration cruise, TOML scientists found that the a logging system developed by ISA (2010) was able to be adapted and enhanced, to describe in some detail the varied morphology of nodules both within the TOML areas and between them.The shapes and sizes of nodules seen were then found to relate to substrate type and setting, and thus likely thickness and long-term stability of the geochemically active layer. Consideration of the various processes that might influence growth helps constrain nodule formation further. The nodules effectively record the long-term geochemical conditions that lead to their formation.ISA (International Seabed Authority), 2010. A Geological Model of Polymetallic Nodule Deposits in the Clarion-Clipperton Fracture Zone and Prospector’s Guide for Polymetallic Nodule Deposits in the Clarion-Clipperton Fracture Zone. International Seabed Authority Technical Study: No. 6 ISBN: 978-976-95268-2-2"

Jan 1, 2017

By D. S. Cronan

Based on analogy with the Clarion-Clipperton zone, three main factors appear to influence the occurrence of potentially economic nodules in the study area, (i) elevated biological productivity, mainly above 50gCm-2y-l, (ii.) sea floor depth near or below the CCD, (iii) an absence of turbidite sedimentation. These conditions are fulfilled in parts of the following basins, where available data indicate that high grade and sometimes abundant nodules occur. i) The East Central Pacific Basin west of the Line Islands extending to the East Central Pacific Basin north and east of the Phoenix Islands ii) The West Central Pacific Basin west and northwest of the Phoenix Islands iii) The North Penrhyn Basin north of Penrhyn Island Notwithstanding the similarities between the environmental conditions under which potentially economic nodules occur in the Clarion-Clipperton zone and in the areas listed above, such similarities may relate only to present day conditions. During the possibly long periods of nodule formation, environmental conditions may have varied, and the deposits formed under conditions different from those prevailing at the present day. However, the fact that both present day conditions and the deposits in the two areas do show similarities suggests that applying the same genetic model to them has some validity. Possibly, any changes in environmental conditions during the period of formation of the deposits has been similar in both areas. Such uncertainties can only be resolved by a much fuller evaluation of the evolution of nodule deposits in both areas throughout recent geological time.

Jan 1, 1986

By Wenbin Ma, Cees van Rhee, Dingena Schott

Since the concept of deep sea mining (DSM) was proposed by J. L. Mero with his book, The Mineral Resources of the Sea, in the 1960s, many research and significant developments have been implemented. However, its commercial mining process still has not yet commenced. One of the most important issues is that a sustainable DSM transport plan is difficult to determine, taking into consideration the DSM technological, economic, and environmental aspects simultaneously. The objective of this paper is to propose a method to determine the sustainable DSM transport plan utilizing a fuzzy analytic network process method, which is a typical multi-criteria decision making method (MCDM). The DSM transport plans evaluating major criteria consist of technological, economic, environmental, and social aspects with both qualitative and quantitative attributes. Different major criteria include several sub-criteria, respectively:  Technological aspect: energy consumption, proven technology, technology reliability, production rate, technology availability;  Economic aspect: gross income, capital cost, operation and maintenance cost, investment recovery period;  Environmental aspect: species disturbance variance, severity of ill effect, turbidity of ocean water, total organic carbon content, sedimentation thickness;  Social aspect: social acceptability, policy support; The weights for all evaluating criteria and sub-criteria are determined through a questionnaire survey interviewing experts at different research fields. All the transport plan candidates are ranked based on a comprehensive index. The conducted research in this paper is meaningful to promote the DSM commercialization process.

Jan 1, 2018

By Sang Joon Pak

Deep-sea mineral resources explored by Korea are categorized into mainly three types; manganese nodules, manganese crusts and seafloor massive sulfides. Manganese nodules have high Pt enrichment factors (EF=400, ore/crust ratios). Rare earth oxides (REO) contents from manganese nodules show from 0.037 to 0.302 REO% with mean value of 0.12%. Te and Pt are highly enriched in manganese crusts, displaying EFs of 10800 and 150, respectively. REO contents of manganese crusts are slightly richer than manganese nodules (0.013~0.387 REO%, average = 0.18 REO%). Seafloor massive sulfides deposits are featured by outstanding values of Se (EF=1300) well as In (EF=110). Au (0.8~26.3 g/t) and Ag (0.9~348.0 g/t) are another enrichment metals in SMS, although they belong to precious metals. Rare earth elements of SMS are meaningless as resources but REE are increasing in sediments overlying SMS. Heavy rare earth elements (HREE) from both manganese nodules and manganese crusts are typically higher than ones from land-based REE deposits. HREO grade and their portions of manganese nodules as well as manganese crusts are greatly similar to ion-absorbed type REE deposits in China, implying REE of subsea mineral resources are absorbed in nodules and crusts. Rare metals including REE could be exploited as by-production of commodities such like Ni, Co, Cu and so on. Rare metal resources from manganese nodules and manganese crusts are featured by low-grade and large scale deposits. Therefore rare metals in subsea mineral resources will add its economic values.

Jan 1, 2011

By Philomene Verlaan

Analysis of the relationship between environmental parameters and the content of Mn, Ni, Co, Cu, Fe and Zn in ferromanganese crusts permits improved identification of locations to prospect for crusts with commercially valuable concentrations of these metals. In this study we asked whether a statistically significant relationship exists between primary productivity of the overlying surface waters, the concentration of O2 in and depth of the O2 minimum layer on the metal content of non-hydrothermal ferromanganese crusts in the Pacific Ocean between 130o W and 175o E and 0o to 30o S (the study area). To further develop the interpretation of the results of the statistical analysis and to assess in detail the geographical expression of these parameters in terms of metal content in crusts, a geostatistical technique (kriging) was used to generate contoured values for metal content, primary productivity and O2 concentration in and depth of the O2 minimum layer in the study area.

Jan 1, 2001

By G. A. Tret’yakov, V. A. Simonov, I. Yu. Melekestseva, V. V. Zaykov, N. N. Ankusheva

The Kyzyl-Tashtyg massive sulfide polymetallic deposit is situated 120 km north-east of Kyzyl (the capital of Tuva Republic, Russia). It is located in the Ulug-O volcanic zone which is interpreted as the northern segment of the Kaa-Khem rift in Sayano-Tuva marginal sea, one of the Paleoasian Ocean margin (Fig. 1) [Zaykov, 2006]. Since its discovery in 1946 the deposit has been studied by many researchers. Significant information was published by Kuzebny et al. [2001] and Zaykov [2006] who proposed volcanogenic-sedimentary genesis. A single reference in English about Kyzyl-Tashtyg is available [Herrington et al., 1999].

By Sofia Martins, Anna Lichtschlag, Sven Petersen, Fernando Barriga, Bramley Murton, Adeline Dutrieux

"Sediments in the vicinity of the hydrothermal seafloor massive sulphide (SMS) mounds are characterized by high concentration of metallic particles. They result from a long process of weathering of the primary mineral deposits and have been accumulated in depressions by mass wasting and hydrothermal plume fall-out. We present here the first results obtained on pore waters analyses of such sediments in distinct geological seafloor environments (in low-temperature hydrothermally active zones, on extinct hydrothermal mounds and in a remote depositional channel). Vertical concentration profiles suggest that the pore fluid composition is affected more by seawater circulation compared with hydrothermal fluid flow in all environments. The composition of pore fluids is affected by diagenesis and redox processes in the distal depositional channel where Mn2+ is released at depth with Cu2+.IntroductionMarine hydrothermal fields, hosting seafloor massive sulphides, are potential resources for future deep-sea mining and might become economic reserves for the industries. They are widespread at mid-oceanic ridges, arcs and back-arc spreading centers (Hannington et al., 2011; German et al., 2016). Sediments in the vicinity of these fields can contain unusually high concentration of Fe, Mn, Zn and Cu among other metal elements (Shearme et al., 1983). These hydrothermal, or metalliferous, sediments result from a combination of processes such as collapsing and weathering of chimney material, filling of the channels by turbidite-like mass wasting, in situ authigenic mineralization and hydrothermal plume fall-out (Goulding et al., 1998; German et al., 1990). The sediments contain important indicators reflecting the development of the hydrothermal systems. Because of their widespread distribution and metal content, they themselves can be considered potential mineral resources. Circulation of seawater through these deposits, however, often modifies the sediment composition by oxidizing the sulphides into oxyhydroxides and clays causing mobilization of the metals. To address the importance of alteration and diagenesis of these hydrothermal sediments, including the result of seawater circulation, we investigated the post-depositional processes occurring in the hydrothermal sediments at the TAG Hydrothermal Field (Mid-Atlantic Ridge, 26°N), focusing on the mobility of metallic cations in a number of different seafloor environments."

Jan 1, 2017

By I. Yu. Melekestseva, V. V. Zaykov

Paleooceanic structures of the Urals fold belt contain different volcanic-hosted massive sulfide deposits of the Urals, Kuroko and Cyprus types [Prokin, Buslaev, 1999]. Small Cobearing massive sulfide deposits, as Ishkinino, Ivanovka and Dergamysh, associated with ultramafites of the Main Urals fault, are less known. Interest to them had arisen after discoveries of the modern “black smokers” associated with ultramafic rocks of the Middle-Atlantic Ridge (MAR). Ores of the Urals deposits are enriched in Co (0.3 %) and Ni (0.6 %) that are concentrated in Co-Ni-Fe-sulfides, sulfarsenides, and arsenides. Ores also contain the increased gold contents – 3–6 ppm and up to 16 ppm in those saturated with As-bearing minerals. The aim of the paper is a comparison of precious metal mineralization in ores from the Paleozoic and modern ultramafic-hosted massive sulfides.

Aug 24, 2006

By Ivar Eskerud Smith, Ole Jørgen Nydal, Niranjan Reddy Challabotla, Svein Sævik

INTRODUCTION Airlift pumping, utilize compressed air that is injected at the bottom of a vertical pipe submerged in the water, reduces the mixture density inside the pipe and lifts the liquid or mixture of liquid and solids. This type of pumping technology, which is simple and without moving parts submerged in water, which provides several advantages compared to the mechanical pumping. Airlift is used in various difficult pumping applications such as transport of fluids corrosive to metals, explosives, nuclear and toxic materials in chemical industries, diamond mining and coal transport. Application of airlift to deep sea mining conditions was investigated by extensive laboratory experiments [1], theoretical analysis [2], and limited proof of concept field studies [3] starting in 1970’s with the discovery of huge amounts of manganese nodules discovered on the seabed at a depth of ranging from 4000 to 6000 m . Even after extensive investigations over the last five decades, there exists no commercial application of airlift technology for lifting of minerals. The major problems with the application airlift for deep ocean mining was (a) lack of control over the expansion of the injected gas, which increases the velocity in upper part of the riser pipe (b) lower efficiency compared to mechanical pumping [3]. Different flow regimes are encountered in airlift pumping: bubble, slug, churn and annular flow. Annular flow regime is the least efficient in lifting of particles and churn flow has better efficiency [3].

Jan 1, 2018

By Marlene Olivares Cruz

The particles that make up the deep-sea sediments have two main sources: 1) those that are created in situ from dissolved components and 2) those that are washed into the ocean in solid phases from the continents, atmosphere, space and interior of the Earth. Many particles as they sink through the water column reaches the seabed and are known as pelagic sediments with terrigenous, biogenic, authigenic, and cosmogenic components. Among the minerals found in the terrigenous fraction of pelagic sediments are quartz, clay minerals, feldspar, micas, ferromagnesians, and the biogenic fraction with remains of siliceous organisms, such as, radiolarian and diatoms. The chemical nature of marine sediments is controlled by the contribution of particulate matter derived from various sources with varying compositions for the fixing of elements during deposition and the compositional changes carried out within the sediments during diagenesis. In the last decade there have been several studies on the mineralogical composition of seabed sediments, suspended particulate materials and cores, together with paleontological and geochemical data are used for paleoclimatic and paleoenvironmental reconstructions, analyze changes in sea level, stratigraphic correlations and identify past and present sources of sediment and terrigenous input pathways and to describe the current ocean mass (Martins et al., 2001, Oliveira et al., 1998). There is also a scientific and economic interest in the authigenic fraction of pelagic sediments formed from other materials for polymetallic nodules. The study of sediments associated with polymetallic nodules helps to know the genesis, evolution and occurrence of these deposits (De Koven et al., 2003, Dubinin et al., 2008).

Jan 1, 2011

By Andrea Koschinsky, Sophie Paul

"INTRODUCTIONOnce again deep-sea mining has been receiving a lot of attention in recent years. Industrial and political advancements also call for environmental baseline studies and analyses to aid the development of standards and monitoring protocols. As part of the EU research project “JPI Oceans: Ecological Aspects of Deep-Sea Mining”, the RV Sonne cruise SO242 to the Peru Basin revisited the DISCOL area that had been artificially disturbed in 1989. This offered the unique opportunity to study a deep-sea site 26 years after a disturbance similar to manganese nodule mining had been carried out (Figure 1). A comparison of a variety of undisturbed and disturbed sites shed light on the re-establishment of a geochemical equilibrium and a range of baseline values. This information can help to inform standard development for monitoring and mining purposes.Heavy metal data and its applicationResearch findingsDuring the cruise, disturbed and undisturbed surface sediment was sampled. The pore water analyses show that the 26 years old disturbance is not visible in the metal profiles and that the pore water reaches equilibrium through diffusive fluxes relatively quickly. The sediment, however, shows some differences between disturbed and undisturbed sites in the upper 20 cm, even after 26 years. Lower concentrations in the usually manganese-oxide rich top layer, variations and “unnatural” peaks in the manganese profiles, for example, suggest removal or mixing of the top layer (Figure 2)."

Jan 1, 2017

By Valcana Stoyanova

Deep-sea mining of polymetallic nodules are expected to produce serious impact on benthic ecosystem due to removal of nodules, sediments and associated fauna by means of collector, and subsequently, by the resettlement of sediment plume which may affect seabed biota outside mining tracks through blanketing, smothering and feeding interruption. The scale and magnitude of the exact impact of commercial operations is not known at present, but its assessment strongly required acquisition of the adequate environmental baseline information. During the past two decades, IOM carried out a total of 20 research cruises in the eastern part of Clarion-Clipperton Zone (CCZ) with purpose to obtain essential data and information on polymetallic nodules and to prepare for future development their deposits. Whilst evaluating the nodule coverage at particular station from both seafloor photographs and box-core recoveries it was ascertain that the ground-truth data plotted against the photo data indicated substantial differences between two methods. Understanding of this phenomenon has not only the methodology meaning related to the efficiency of the using photoprofiling techniques during exploration of nodules, but also it could be of environmental importance because the similarity between natural sediment blanketing occurrence in studied area and expected re-deposition and blanketing of sediments which will be disturbed during mining operations.

Jan 1, 2011

By U. Schwarz-Schampera, P. Stoffers

The main characteristics of the 2545 km Tonga-Kermadec subduction system are the subduction of the Pacific Plate and its sedimentary cover in the Tonga-Kermadec trench and the extension and rifting of the lithosphere behind the active island arc in the Lau basin - Havre Trough back-arc systems. The subduction of the Louisville Seamount chain at 25.6°S affects the tectonic and volcanic system and separates the island arc into the Tonga arc and the Kermadec arc, respectively. To the west, a Miocene island arc is represented by the Lau-Colville ridge. The crustal extension between the Lau-Colville and the Tonga-Kermadec ridge started at about 6 Ma, and induced their separation and the onset of the southward rifting since about 5 Ma. Characteristics of the Tonga-Kermadec arc system include (i) the fourthfold decrease of the subduction rate from 24 cm/a in northern Tonga to 6 cm/a in the southern Kermadec trench, mainly north of 23.5°S; (ii) the development from fast spreading in the Lau basin (16 cm/a) to slow rifting (2 cm/a) in the southern Havre Trough with the transition from spreading to rifting at 23.5°S; (iii) variations in the composition and the volume of the subducting sediments and rocks (detritus from the Samoan hotspot at the northern Tonga arc; the aseismic Louisville ridge at the southern Tonga arc; increasing terrigenous sediments from New Zealand at the southern Kermadec arc); (iv) a number of active volcanic centers younger than 1 Ma and characterized by significant shallow submarine hydrothermal systems.

Aug 24, 2006

By P. Mikhailik

Recently, characterized by fast development high- and nano-technology, demand for rare and trace metals has increased. One of such metals is gallium. Gallium compounds, mainly GaAs, are used in medicine, to manufacture optoelectronic devices, microwave techniques, devices of solar power and infrared optics, etc. The basic gallium industrial deposits are known only on land. There are bauxites (50 ppm), nepheline rocks and ores (36-38 ppm, minerals concentrators are nepheline and sodalite), Zn-Pb-Cu ores (5000-12000 ppm, minerals concentrators are gallite, germanite, sphalerite, bornite), sulphide-polymetallic and Pb-Zn ores (10-32 ppm, minerals concentrators sphalerite, chalcopyrite) (Vershkovskya et al., 1998). High concentration of gallium are observed in hydrothermal massive sulphides of a Mid-Okinawa Trough (The South Chinese Sea) and Sujo seamount (The Philippine Sea) (Noguchi et al., 2007). As it is known, deep-sea massive sulphides and associated Fe-Mn crusts are products of hydrothermal fluid discharge. High-temperature massive sulphides precipitation are the first, and low-temperature Fe-Mn crusts deposition is the last process of hydrothermal mineralization (Cronan, 1982). Hydrogenic crusts and nodules of the World ocean are characterized by low concentration of Ga, close to clarke (19 ppm) (Kobaltbogatye.., 2002). Hydrogenic crusts from the Sea of Okhotsk are exception, because Ga concentrations are exceeded clarke in 3,5 times (Mikhailik, et al., 2009). Complex studying of Fe-Mn crusts from deep-sea basins volcanic seamounts of the Sea of Japan has shown their hydrothermal-sedimentary genesis (Mikhailik, 2009). High gallium concentration (up to 850 ppm) was established in these crusts by ICP-MS (Agilent 7500C). Microprobe research (JXA-8100) of samples Fe-Mn crusts has not revealed the gallium minerals concentrators. It suggests that, gallium in Fe-Mn crusts of the Sea of Japan is sorb substance.

Jan 1, 2010

By Robert M. Owen

The reconstruction of ocean history has been a major focus of marine research over the past decade. A significant outcome of these investigations is the recognition that certain types of marine mineral deposits are linked to regional to global scale changes in ocean composition and climate conditions. Manganese-bearing deposits are of particular interest in this regard because changes in their occurrence, distribution and/or composition are responsive to both biochemical and geological factors. Analyses of such deposits whose formation spans critical age/epoch boundaries thus provide clues concerning the interplay of different process during anomalous periods in Earth history. Recent studies demonstrating this deposit - event - process relationship include: (1) Changes in the bulk chemical composition of ferromanganese crusts during the Late Miocene-Early-Pliocene (-7-3 Ma) that coincide with a period of enhanced biological productivity in the eastern equatorial Pacific upwelling zone; (2) The formation of large statiform manganese deposits at the Cenornanian- Turonian Boundary (-92 Ma) in association with widespread oceanic anoxia; and (3) Increased deposition of hydrothermal precipitates caused by tectonic reorganizations at the Paleocene - Eocene boundary (-55 Ma) that resulted in global-scale changes in atmospheric and oceanic circulation and climate.

Jan 1, 1995

By Robert G. Ditchburn, Cornel E. J. de Ronde, Bernard J. Barry

The age of mineralization, its mode of formation, the time elapsed to amass an economic deposit, its capacity for sustainable extraction and, ultimately, its grade and tonnage, are key aspects in the economic viability of volcanic massive sulphide (VMS) deposits (Ditchburn et al, 2004). Radiometric dating methods applied at GNS Science have been recently refined with the purpose of efficiently determining the ages of seafloor VMS mineralization along active intraoceanic arcs. These developments include: determining the longevity of seafloor hydrothermal systems, details of individual chimney and massive sulfide mound growth, and insights into deep-seated processes, such as the transfer of elements from magmas to their overlying hydrothermal systems. In our pursuit to better understand seafloor hydrothermal systems along intraoceanic arcs, we have thus far compiled age information for three volcanic centres of the Kermadec arc (South Pacific) and one of the Mariana arc (NW Pacific).

By Michael W. Milner

Cold Ocean Placers: Polar storms, interstadial littorals and crustal adjustments. Polar storms with consistent strong winds in the Southern, Antarctic Ocean are responsible for placer deposits on both the east and west coasts of Australia, on the west coast of New Zealand, as well as on the coasts of South America and Africa. Arctic winds, confined by both land and ice, generate similar placers in Labrador and Greenland as well as on the coasts of Scotland, Norway, Hudson's Bay, Nome, Goodnews Bay, Kamchatka and the north coast of Siberia. Tasman and Labrador seas have several parallels to Newfoundland, including north-south polar waterways, young spreading ocean floors, and youthful coastal escarpments with glaciated coasts. Black sand beds in beach deposits on the modern and Pleistocene transgression strandlines, skewed to the distal ends of beaches, and set into either bedrock or sediment fill, are the locus of the light-heavy mineral placers with titanium, zirconium and rare earth elements; chromium; iron; and tin. Gold and platinum group elements are the ultra heavy minerals at one end of the spectrum and tend occur in proximal placers generated, either directly from bedrock sources, or as minor by-products in distal light-heavy mineral placers. Diamonds are unusual in that the value is only in the larger stones, despite the formation of beach sand and aeolian placers in the littoral zone, and the sites of concentration are in very high energy bedrock traps, on terraces that are mined to depths of 100 metres below sealevel.

Jan 1, 1995

By P. Mikhailik

Recently, characterized by fast development high- and nano-technology, demand for rare and trace metals has increased. One of such metals is gallium. Gallium compounds, mainly GaAs, are used in medicine, to manufacture optoelectronic devices, microwave techniques, devices of solar power and infrared optics, etc. The basic gallium industrial deposits are known only on land. There are bauxites (50 ppm), nepheline rocks and ores (36-38 ppm, minerals concentrators are nepheline and sodalite), Zn-Pb-Cu ores (5000-12000 ppm, minerals concentrators are gallite, germanite, sphalerite, bornite), sulphide-polymetallic and Pb-Zn ores (10-32 ppm, minerals concentrators sphalerite, chalcopyrite) (Vershkovskya et al., 1998). High concentration of gallium are observed in hydrothermal massive sulphides of a Mid-Okinawa Trough (The South Chinese Sea) and Sujo seamount (The Philippine Sea) (Noguchi et al., 2007). As it is known, deep-sea massive sulphides and associated Fe-Mn crusts are products of hydrothermal fluid discharge. High-temperature massive sulphides precipitation are the first, and low-temperature Fe-Mn crusts deposition is the last process of hydrothermal mineralization (Cronan, 1982). Hydrogenic crusts and nodules of the World ocean are characterized by low concentration of Ga, close to clarke (19 ppm) (Kobaltbogatye.., 2002). Hydrogenic crusts from the Sea of Okhotsk are exception, because Ga concentrations are exceeded clarke in 3,5 times (Mikhailik, et al., 2009). Complex studying of Fe-Mn crusts from deep-sea basins volcanic seamounts of the Sea of Japan has shown their hydrothermal-sedimentary genesis (Mikhailik, 2009). High gallium concentration (up to 850 ppm) was established in these crusts by ICP-MS (Agilent 7500C). Microprobe research (JXA-8100) of samples Fe-Mn crusts has not revealed the gallium minerals concentrators. It suggests that, gallium in Fe-Mn crusts of the Sea of Japan is sorb substance.

Jan 1, 2010