Search Documents

By G. Yan

The gas diffusion layer (GDL) is one of the most critical components of the proton exchange membrane fuel cell (PEMFC) in achieving good performance. The GDL serves as a current collector, transport media for fuel and oxidant to the catalyst layers, a support for the catalyst layer and a medium for water management. In this paper, we will discuss the modeling and experimental measurement of the reactant distribution in the GDL and to the catalyst layer. This will be done for some new and advanced engineered GDLs. Novel optical technique which correlates measured data with reactant distribution are used. This technique combined with modeling allows optimal design of engineered GDLs.

Jan 1, 2005

By X. Z. Yuan

Contamination introduced by the impurities from the feed stream can impact the PEM fuel cell performance dramatically. The presence of these unwanted trace species such as CO, H2S, NH3, can adversely affect the fuel cell functioning. It has been reported that the major impact of CO and H2S contamination on the fuel cell performance is kinetic while the effect of NH3 contamination is speculated as membrane conductivity reduction only. In this paper, a model regarding the NH3 contamination is described and the mechanism of the NH3 contamination is illuminated by the model calculations.

Jan 1, 2005

By Michael J. Beare

Requirements of both local permitting and international fundraising are forcing increasing numbers of projects in Russia and CIS to carry out dual technical studies. The principal focus of Russian mining project design is to satisfy local regulatory requirements. However, the technical documents are not generally accepted by international banks for project finance outside Russia. Similarly, international study documents are not accepted for permitting in Russia. The purpose of this paper is to compare and contrast Russian and international approaches to mine technical studies and draw conclusions from this. The Russian design and permitting system is centered around two key statutory technical documents termed the TEO Konditsy and the TEO Project. These documents are subject to regulatory approval and are broadly equivalent to the international prefeasibility study and the feasibility study respectively. A comparison of study criteria suggests similar approaches are used for the main technical disciplines in project design by the time projects are at the point of construction, but there is divergence on environmental matters where the OVOS (Russian ESIA equivalent) differs from an ESIA in some significant areas. The key differences relate to project footprint, level of technical detailed required for baseline studies, level of public consultation, consideration and disclosure of information, labour, coverage of community and social issues and the preparation of a Social and Environmental Management System (SEMS). It has been noted that the Russian Design Institutes often leave the detailed economic analysis until after the TEO Konditsy. A common problem is design teams tend to look for ?technological solutions? without due concern for project economics. The end result of this can be mines that are overcapitalized and hence sub-optimal. It can be concluded that Design Institutes have the monopoly on Russian permitting reports and this is likely to continue. Similarly, Russian institutes generally do not prepare feasibility studies to international standards and this is likely to continue to be the case. Therefore to achieve the requirement of dual technical studies, the international consultants and Russian Design Institutes will need to cooperate on a joint work program. Key issues will be to ensure the most appropriate option studies are carried out at the right stages, that project economics are considered throughout the study, and that the environmental work program covers the additional studies necessary for the ESIA.

May 1, 2009

By J. C. Mitcheson

Mr. President, Mr. Mayor, Ladies & Gentlemen: IT GIVES ME great pleasure to have the opportunity, today, to speak on behalf of all the constituent. bodies of the Common-wealth Council of Mining and Metallurgical Institutions. For the past month we delegates have been right royally entertained across the length and breadth of Canada by Provincial Governments, City Councils, and other equally generous public organizations and private corporations. On this occasion, however, the President of The Canadian Institute of Mining and Metallurgy, our good friend Dr. H. J. Fraser, has been our host at the enjoyable reception preceding this Institute Luncheon, which luncheon was sponsored by our official host, The Canadian Institute of Mining and Metallurgy, one of our .constituent bodies.

Jan 1, 1957

By J. O. G. Posada

Magnesium derived foams were prepared by using the so-called baking of powder blended precursor material method. This method comprises mixing magnesium powder with a small fraction of blowing agent (ZrH2, Cs2CO3 and CaH2) and Ni like catalyst, compacting this mix and creating a foam by heat treatment above the magnesium melting temperature. The resulting samples were characterised by microscopy, gas adsorption (BET method) and by small angle neutron scattering. Several mathematical models were used in order to determine particle size distribution, fractal dimension and total pore volume fractions.

Jan 1, 2005

Toronto 2013 Proceedings

May 1, 2013

By Jucheng Wang

Unplanned open stope dilution is a major cost factor for many mining operations, even though significant advances in empirical and analytical approaches for estimating stope dilution have been made. Many factors that influence hanging wall dilution are still either ignored or assessed in purely subjective terms. Undercutting the stope hanging wall on both the overcut and undercut development are well recognized factors which contribute to hanging wall instability and dilution. In many mines, undercutting the hanging wall breaks the integrity of the rock mass that may form along continuous foliation or bedding planes parallel to the stope hanging wall contact, reducing stability. This undercutting also increases the zone of destressed or relaxed rock that may potentially fall into the open stope as dilution. An approach is introduced for quantifying the effect of undercutting on potential stope dilution. An extensive database of stope case histories has been collected to look at dilution from Hudson Bay Mining and Smelting operations (HBMS) in Flin Flon.

May 1, 2002

By L. Voisin, E. Díaz, V. Montenegro, W. Kracht

Grinding media is of great concern in the mining industry mainly because its consumption represents an important part of the costs during mineral processing and consequently, of the total mining business OPEX. In addition, grinding media consumption impacts directly on flotation performance through negative contamination by corrosion, affecting the pulp chemical potential, complicating the understanding and control of the process, as galvanic interactions between mineral species also occur. In addition, during the process there is also a physical consumption of the grinding media through erosion and impact. In both cases, mineralogy has an important role because pulp abrasion power, chemical reactivity, rheology, hardness and other variables depend on the minerals contained in the pulp and their interactions. In the present study, a geometallurgical and phenomenological model, which describes the grinding media consumption and its relationship with mineral hardness expressed by Bond Work Index, was obtained based on advanced mineral characterization techniques such as Hylogger3TM, X-ray diffraction, X-ray fluorescence and experimental grinding tests using a laboratory mill applied on Chilean copper pulps. The results obtained show that pH has an important effect on grinding media consumption, because corrosion varies with hydrogen ions availability. Also, mineral hardness depends on mineralogical composition, but textural analysis must be performed to have a better description of this property. Finally, minerals present in a sample define the grinding media consumption mechanism, because a sample with harder minerals and a greater value of Bond Work index is capable of protecting grinding media from impact wear, while a sample with lower hardness but with a big sulfide minerals content would be more aggressive with grinding media because corrosion is more important in this case. The geometallurgical model obtained is capable to relate the grinding time, mineral hardness, content of sulfide minerals and grinding pH to estimate the grinding media consumption.

Jan 1, 2017

By J. B. Evans

"THE OPPORTUNITY to participate in a CIM seminarconcerning the direction of mining engineer trainingis perhaps fortuitous as it comes at a time when theengineering schools which have invited inspection byCanadian Accreditation Board of the Canadian Councilof Professional Engineers are examining theirrespective curricula.Currently there exists considerable soul-searching in various engineering schools across Canada where questions such as the following are being posed.- Have we achieved the correct balance between subjects related to technical methodology and subjects devoted to conceptual planning and design?- Should we include ""applied humanities"" in our program? (Whatever ""applied humanities"" might mean!)- Should courses covering pollution control, ecology, economics, technical writing, professional conduct and ethics be offered as compulsory subjects, as electives, or not at all?- Is it a better scheme to have students complete an Arts or Science degree before entering engineering?- Do we place too much emphasis on pure mathematics and sciences with the result that insufficient time is available for instruction in the engineering applications of these subjects?- Should English expression and/ or literature be included in the engineering programs and, if so, should these subjects be presented by the English department or by English lecturers captive to the engineering school? - Is the present program directed primarily at research activities rather than preparing engineers for their future roles in industry? - Should we teach our own versions of mathematics and physics? - Do we have sufficient engineers on the faculty strength or are we overloaded with Ph.D.'s from the pure sciences? - How flexible should the program be, what should the compulsory vs elective course content be, and what freedom of choice, if any, should be given with respect to elective courses? - To what extent should students contribute to faculty decisions?- How far should we pursue computer science subjects and do we need to make our students proficient in computer programming? - How far should operations research and mathematical models be carried in the undergraduate program when the students have limited experience in the real engineering world? - Realizing that an engineer never completes his education, should the undergraduate program cover ""bare bones"" engineering and should instruction in particular disciplines be left to graduate schools and / or industry?"

Jan 1, 1972

By W. L. Stuewe

For the purpose of this paper I shall, in order to limit myself, define the words 'Maintenance' and 'Equipment' as follows: Maintenance shall mean the 'care of or 'the sustaining of equipment in as nearly perfect condition as possible. Equipment shall mean any item of a mechanical nature entering into the production of coal; it will be seen that unless one limits the use of this word it could take in administration as well as operative equipment, and include metal mines, mills and smelters, and manufacturing plants. In any industry the first consideration is the proper operation of all units entering into the production of the article manufactured or produced. I wish to quote here what a man, well known internationally in financial circles, told his operators at the time a large expansion programme was under consideration. His exact words were: "I do not care how much it is going to cost. What I want to know is how much it is going to cost to operate and maintain. It is the continuous drain for repairs that costs us the most money." The truth of this statement has been proved time and again, and many companies have found the cost of maintenance to be the balance between profit and loss-so much so that, in two instances with which the writer is familiar, the mechanical equipment was practically replaced throughout. I bring this point out here to emphasize the value and necessity of keeping abreast of the times, and obtaining maximum efficiency with the minimum outlay. Time is indeed money where delays occur due to defective or poorly kept equipment, and it is absolutely necessary to prevent machinery from becoming defective or inefficient.

Jan 1, 1930

By Stuart J. Schofield

Introduction The study of the ore deposits of British Columbia is one of fascinating interest not only from a scientific but also from a commercial standpoint and certain wide problems in connection therewith have interested me for some years. Several of these problems have been set forth in papers presented before this Institute on previous occasions. In 1918 it was pointed out that the commercial ore deposits of British Columbia, with one exception, were associated with the granodiorite batholiths of upper Jurassic age. This was followed, in 1922, by a discussion of the ore deposits of British Columbia in which the mineral belts of the province were defined and named, showing a zonal arrangement of ores in which the Pacific coast deposits are characterized by the presence of copper, while the interior belt is marked by the presence of silver, lead, and gold. Methods Of Investigation In reading various reports on the economic geology of British Columbia one is struck with the fact that the mineral veins may be arranged as a system and further examination will show that such a system follows two main directions, one northeasterly and the other northwesterly, both related in origin to the same force.

Jan 1, 1925

By Kenneth L. Graham

Horizontal directional drilling from existing underground workings will greatly reduce, if not replace, surface exploration drilling. Diminishing ore reserves along with increasing difficulty in acquiring access and permitting of drilling surface holes requires a change in procedure. The length and direction of the required long holes is site specific, but once determined could be quickly mobilized. Data would be available for a much more timely evaluation without any surface disturbance and required reclamation issues. Preplanned directional drilling from underground will also provide an evaluation of already inconsistent uranium deposits located under surface terrain that is inaccessible to surface drilling.

Aug 1, 2010

By Mauro Chiesa

An Overview on the Presentation A.The Markets ?Mining Industry ?Capital Markets ?A Six-Cell Matrix of Strategic Options B.De-Risking The Mining Assets ?The Value-Added ?The Assets: Current and in Development ?The Feasibility Study C.(Questions, and answers) Post-Crunch: Some Maxims ?Three Metal Market Models No Longer Prevail ?New models are uncharted: ?be prepared?(ref: Lord B-Powell). ?Capital markets are pricey & uncertain: be your own financier first ?focus on value and on cash-flow (not oz, lbs, tonnes, LOMs, etc) ?Know your banker/financier(and it should know mining) ?In the past, it was ?know your borrower? ?It?s a buyer?s market that wants the ?right deal?: so cast a big net: ?Data must be current, concise and consistent ?3rdparty validation of feasibility work is now a ?passport? ?The risk matrix, with de-risking, is as important as the ?math?

May 1, 2011

By Joey R. Kish, Shooka Mahboubi, Hatem S. Zurob, Gianluigi A. Botton

The kinetics of the Cr2O3-based scale oxidation and volatilization were studied in the presence of water vapour (H2O). A commercial Cr2O3-based scale forming Type 310S stainless steel was examined at the ambient pressure (0.1 MPa) and 550ºC in relatively low and high H2O containing environments of air- 10% H2O and air- 70% H2O, respectively. The increase in the partial pressure of H2O (pH2O) from 10% to 70% resulted in transition of the oxidation and volatilization kinetics from the parabolic rate law for air-10% H2O to the paralinear rate law for air-70% H2O. The kinetics transition was attributed to the increase in the Cr loss rate from the base scale after coupons exposure in air- 70% H2O. The significant role of the Mn alloying element in the base scale protectiveness was also discussed in the context of the Cr2O3-based scale stability.

Jan 1, 2017

By B. D. Frater

Geometallurgy or process mineralogy is an integrated part of the scoping, pre-feasibility and feasibility phases of a project as well as an existing operation. A well planned and executed geometallurgical testwork programme during the early phases, will result in a more accurate decision making process during the selection phase. The better this integration between geological, mining and metallurgical data gathering during the early phases, the more accurate the predictions will be with regards to throughput and recovery during modelling and process and equipment selection in later phases. This will enhance and improve the mine and process scheduling and subsequent NPV. Geometallurgical information gathered during plant operation and testwork can for example be used to statistically model the pit optimisation, plant throughput and optimise the plant for certain feed material (characterised by statistical models).

Jan 1, 2017

Polymer electrolyte membrane (PEM) fuel cell has increasingly become the potential choice of zero-emission power source for portable, mobile and stationary co¬generation applications. However, technical barriers need to be overcome before its widespread commercialization; cost reduction and performance improvement including reliability are the two key areas, that can be realized through better cell/stack design and improved understanding of the transport processes occurring inside the individual cells and stacks. In this presentation, we will provide an overview of various cell/stack models that are available in the literature, their strength and weakness, and then present a comprehensive multi-species, multi-phase and multi-dimensional formulation of a single PEM fuel cell, with consistent and systematic formulation for all the regions involved, including the solid bipolar plates, gas flow channels, the electrode backing layers, the catalyst layers and the electrolyte membrane. Such a detailed approach allows us to extract sufficient information to the analysis of a stack of PEM fuel cells. Stack model will be presented that investigates the various stack designs and flow configurations, and the optimal stack design based on the present study will be described. Also some innovative cell/stack designs will be featured.

Jan 1, 2005

By Deborah McCombe

"By now, most geologists and engineers in the Canadian mining industry are familiar with National Instrument 43101 Standards of Disclosure for Mineral Projects (NI 43-101) and the Canadian Institute of Mining, Metallurgy and Petroleum (CIM) Definition Standards for Mineral Resources and Mineral Reserves, which are incorporated by reference in NI 43-101. In recent years, significant progress has also been made in establishing standard reporting practices internationally that recognize the globalization of the industry and enable investors to compare projects anywhere in the world and make informed investment decisions. This article is part of a series that will summarize the background and development of international resource and reserve reporting standards by the Committee for Mineral Reserves International Reporting Standards (CRIRSCO), highlight its current activities and provide insight into international mineral reserve and resource reporting issues. CRIRSCO was formerly the Mineral Definitions Working Group of the Council of Mining and Metallurgical Institutions (CMMI), an organization representing professional bodies in all of the major mining and mining investment countries. In 2002, CMMI disbanded and CRIRSCO continued as a volunteer committee with limited funding from those professional bodies and increasingly from other sources, such as mining companies and regulatory bodies. CRIRSCO was adopted as a Task Force of the International Council of Mining and Metals (ICMM) in 2007. The ICMM is an influential industry body representing all of the major mining companies and many junior companies through its associated members, such as the Minerals Council of Australia, the Chamber of Mines of South Africa and the Prospectors and Developers Association of Canada. CRIRSCO now has funding to pursue its objectives."

Jan 1, 2003

By D. Xia

Pt-Bi intermetallic Nanoparticles was prepared by the polymer-anchor method. The electron micrographs shows that the dimensions of particles sharply distribute in the range of about 3-6 nm. The elemental ratio of Pt/Bi in the bimetallic particles is estimated by the electron probe microanalysis method. Pt-Bi intermetallic Nanoparticles shows a higher activity for the ORR than pure Pt. No significant dependence of the oxidation currents on the rotating speed of the electrode could be observed in the presence of methanol. This clearly indicates that the Pt-Bi is inactive to methanol.

Jan 1, 2005

By S. Burling

Australia has a number of uranium deposits, but they vary significantly in their mineralogy, grade and textural characteristics. Therefore, information from traditional (or conventional) sources regarding the fundamentals of leaching the uranium and gangue minerals is not always applicable when studying particular ores. Empirical studies on particular ores can be effective in understanding leach systems and can lead to improvements in process design, but there remains a lack of fundamental understanding which is necessary for ongoing process optimisation as ore bodies continue to vary. ANSTO Minerals has undertaken a program of work to address some of the fundamental questions of uranium leaching, including the unexpected impact for some ore types of leaching at high oxidation potential.

Aug 1, 2010

By Richardson A. H.

"IntroductionSafety and training in the mineral industry will always be issues that are hotly debated and discussed.The nature of the mining industry, where people and equipment work in close quarters deep below the earth's surface, attracts a great deal of public attention and concern, especially in the areas of safety and related training activities. This concern has been carried over into the mineral processingsector which is, of course, a vital part of the mining industry.It is therefore imperative that mining people closely examine the policies, procedures and programs presently in place to determine if they meet the needs of the industry and its employees. Everyone stands to benefit: the companies, employees and the mineral industry as an important segment of the Canadian economy.Phrases such as ""Safety First"", ""Safety is Number One"", have a role to play in industrial safety programs but in reality are a shallow approach to the magnitude of the challenge. An industry must produce its products in a cost-effective way, with good employee relations. None of these objectives can be successfully achieved unless accompanied by good safety performance. Accidents both on and off the job result in very poor efficiency, high costs and poor employee relations.This chapter, Safety and Training, outlines those major areas that the author believes are necessary components for an industrial safety, health and training program, but are not all inclusive. More will surely be added as additional problem areas requiring attention are identified. The major sections discussed are: Development and Implementation of a Safety Program; Occupational Health; Training; and Audit Procedures.The author has drawn on his experience as both a mill superintendent, mine manager and superintendent of safety, health and training. The approach developed at loco Metals Manitoba Division is frequently used in this paper with examples and excerpts to better illustrate the subject, but does not represent the full scope of programs in place in the Division."

Jan 1, 1989