Search Documents

THIS article describes the origin and details of a hydraulically operated switch to control the operation of an automatic underground pumping system. This system was installed in December, 1939, on the 2,350-foot level at No. 5 shaft of the Buffalo Ankerite mine. The pumping unit consists of an 8-stage centrifugal pump direct-connected to a 150 h .p., 2,200 volt motor. Pumping capacity is 200 gallons per minute under a 1,315-foot head and with a flooded suction. The control consists of a 200 amp., 2,200 volt oil-immersed starter with thermal overload protection, thermal protection on the pump, and a flow switch that is bypassed for 30 seconds after the pump starts. The 30-second time lag is operated by a relay mounted on the panel. There is a swing check valve in the discharge line of the pump which originally operated the flow switch by means of a connected outside lever which closed the switch as the check valve opened.

Jan 1, 1945

By J. F. Wright

Gold-bearing quartz veins and replacement chalcopyrite deposits are the two important types of metallic mineral deposits of the east central Manitoba mining district. The gold-bearing veins occur along Manigotagan valley, northwest for 25 miles from Beresford lake, and the copper deposits along Oiseau valley, between Oiseau lake and the east end of Lac du Bonnet. Lithium-bearing minerals of possible commercial value have recently been discovered in pegmatite along Winnipeg river about 10 miles east of Point du Bois. There are also prospect pits with showings of galena, sphalerite, cobaltite, pentlandite, nickeliferous pyrrhotite, arsenopyrite, pyrite, molybdenite, cassiterite, and other minerals, but the various occurrences of these minerals, as exposed, are small. The bedrock and mineral deposits of this mining district are Precambrian and resemble in many respects the formations and mip.eral occurrences of western and northern Ontario. Although prospectors visited eastern Manitoba at intervals during the last fifty years, effective prospecting did not begin until 1913 or 1914, and not until 1923 were skilfully directed, systematic explorations undertaken. It is true, that between 1913 and 1923 considerable sums were expended in a number of attempts at mining and milling the gold-quartz ore, but these enterprises failed partly through poor management or attempts to develop veins that were too small or too low-grade to be worked at a profit under the existing conditions of transportation and power supply.

Jan 1, 1925

By K. J. Aglias, M. Jeffery, J. V. Simmons, J. A. Johnston, S. G. Fityus

"Shales and mudrocks undergo weathering in the near-surface geological environment, and degradation when directly exposed at the surface. Despite having superficially similar appearances, many shales have very different degradation behaviours. For example, some shales break down readily upon exposure whilst others remain more or less intact. Further, for those shales which break down, the style of degradation can vary greatly. A phenomenon is described where fresh shale blocks that are exposed at the surface undergo rapid breakdown to a fragmented texture which then persists for relatively long times, without further breakdown to finer soil particles. This is illustrated for some coal mine waste rocks. Furthermore, this metastable fragmented texture seems to be particular to each particular type of shale. The paper presents a conceptual model for this physical breakdown of shales which accounts for the differences in fragmental texture that are observed. The importance of several factors including strength, permeability and expansive clay content are identified for their contribution to the degradation behaviour of different shales.INTRODUCTIONShales and MudrocksThe term shale is applied widely to a class of mudrocks having a range of distinctive but gradational appearances and mechanical behaviours. Mudrocks are sedimentary rocks primarily composed of silt and clay sized particles (Tucker 1982). Mudrocks form in low to very low energy environments such as flood plains, lakes and deltaic environments, where the finest detrital particles are able to settle out of suspension (Reeves et al., 2006; Stow, 2005; Tucker, 2001).Unlike coarser siliciclastic sedimentary rocks, mudrocks do not present with a wide variety of sedimentary structures and textures. The most common texture is a preferred orientation of clays and micas parallel to the bedding plane. This textural component is related to the property of fissility or the ability for such textured mudrocks to split along smooth planes that are parallel to the bedding. Another common structure is lamination, formed by variations of grain sizes and types during deposition, Massive texture describes the situation where no sedimentary structures or textures are apparent (Boggs Jr., 2009; Tucker, 2001). The term shale varies between sources and contexts, with Reeves et al. (2006) stating that a shale is a fissile mudrock, where “fissility is a property that has developed at a certain stage of weathering”."

Jan 1, 2015

By Murray W. Grabinsky

This paper considers thickening mine tailings to dense non-segregating slurry or paste for surface disposal. The driving motivation for this initiative is the elimination of ponds, reduction in containment dams and significant decrease in water being sent to the tailings basin. This inherently reduces risks of environmental and structural failure. Some of the engineering challenges in creating a stable stack of thickened or paste tailings are identified, and possible field and laboratory testing techniques in support of design are discussed. Finally, the integration of monitoring activities into the ongoing management of the surface disposal site is considered.

Nov 1, 2002

By Robert B. Parsons

"The Canadian tax treatment of mining operations outside Canada is not as attractive as the treatment of Canadian operations. Further, the Canadian company that invests abroad a host of complex rules. This month, Tax Notes examines some of the major Canadian tax considerations confronting the Canadian company that wants to invest abroad. IntroductionCanadian-based mining companies are investing abroad more than ever before. These foreign investments trigger a complex set of tax rules that are distinct from the rules that apply to Canadian investments. In most cases, careful tax planning is mandatory if the company's tax liabilities are to be minimized. This article summarizes the main tax considerations that need to be taken into account with respect to a mining investment outside Canada.Branch Versus SubsidiaryOne of the first questions that arises in connection with a prospective foreign investment is ""Should we invest directly (that is, in a branch operation), or should we invest through a foreign subsidiary?"". In the case of a branch operation, the Canadian company owns and operates the business directly - that is, the foreign business assets are part of the Canadian legal entity. In the case of a foreign subsidiary, the foreign business operation is owned and managed by that subsidiary. The tax treatment of a branch and a subsidiary can be quite different."

Jan 1, 1994

By Carol A. Pilon

"IntroductionRECENTLY, the Saskatchewan Research Council (Saskatoon ) marked the completion of one of its coal-related projects with the publication of the Bibliography and Index of Coal in Saskatchewan and Adjoining Provinces and States, hereafter referred to as the Bibliography and Index of Coal. Over a two-year time period, literature was surveyed and indexed and bibliographic data were compiled using a computer-assisted information retrieval system called FAMULUS. The final publication contains 1150 bibliographic references, which are cross-referenced by six indices.The project was initiated in September 1974, in support of Saskatchewan's Coal Resources Evaluation Program , an ongoing research program sponsored by the Department of Energy, Mines and Resources (Ottawa) and the Province of Saskatchewan. This program places emphasis on such areas of concern as the occurrence of deposits, chemical and physical properties, calculation of reserves and computer-assisted applications for the evaluation of lignite resources in the Province. Attention is also given to aspects of geophysical exploration, mining conditions and economics, by-products and the transporting of lignite. These are the subject areas .covered by the Bibliography and Index of Coal.The over -all objectives of the literature indexing project may be enumerated as follows: (1) to build a specialized resource library by surveying established public and specialized libraries, and commercial data bases; (2) to enter library data into the FAMULUS information retrieval system, to be used to generate bibliographies and indexes, and to retrieve information by the use of specified searching techniques; (3) to make this library data available to interested persons."

Jan 1, 1977

By Hao Zhang

Site inspection is an important component of safety management system. In current practices, the inspectors evaluate the safety condition on a construction site with the assistance of a standardised checklist. However, the checklist emphasizes on evaluating the implementation of safety management system, but provides limited task-specific check items for assessing whether the individual construction tasks are conducted under safe condition and in a safe manner. To address this issue, the research presented in this paper aims to provide safety practitioners with comprehensive and taskspecific safety information to promote effective risk identification and facilitate strategic risk control during site inspection. Specifically, this research first builds a project-specific safety information database, which stores potential risks and control measures for each construction task. The research team then develops a mobile decision support tool to retrieve information from the database and support safer decision-making on site. The tool supports users in two ways: one is to provide daily risk checklists and risk control strategies to guide step-by-step inspection alongside the project schedule; the other is to let users input any safety-related keywords during the safety inspection process and the tool returns relevant safety information by applying text mining algorithms. It is ongoing research. This paper presents an overall research framework and discusses the progress in developing safety database and data retrieval concepts. The outcome of the project will help enhance safety management practices and reduce possible risky working conditions on a construction site.

Aug 1, 2013

By K. Kim

"All milling operations would like to achieve the best possible recovery in combination with the highest achievable throughput. Unfortunately, many operations have problems with low recovery, low throughput or both. In the majority of these cases investigated by the author, the solutions to improve recovery and throughput were simple. The solutions did not include implementation of new technology or major capital, but rather a return to fundamentals. In most cases, problems occurred because the operation was not following their own operating procedures, because the design of the circuit was changed without adequate change management or understanding of the implications of changes, or because basic metallurgical measurements and control were not taken or ignored. In this paper, examples of these problems and their solutions derived from long and varied experience will be discussed. The objective of this presentation is to provide the milling operator with practical and readily implementable solutions to common milling issues to improve throughput and recovery.INTRODUCTION Mill operations can be evaluated by many operating parameters, but the two best indicators are recovery and throughput. These two parameters summarize the wellbeing of an operation. The grade to the mill is also a good indicator, but this is usually controlled by the mine. The best recovery and throughput are achieved through a team work involving operators, maintenance workers and metallurgical staff. The milling operations include many unit operations, such as crushing, grinding, flotation, leaching, carbon in leach, Merrill Crowe, roaster, autoclave and refinery. The tools available to the operations are plant design, process measurements, assays, metallurgical balance, and operating strategy. Twelve real life examples of improvements of recovery and throughput are presented in this paper. EXAMPLE 1: CRUSHING CIRCUIT WITHOUT FINE ORE BIN At this operation plant throughput could not be maintained at a high rate because feed to the mill became coarse during the day. The cone crusher was feeding the ball mill directly. As the day wore on, the gap on the cone crusher would slowly increase, which would cause the product size to increase. This would increase the re-circulating load on the ball mill. The throughput would decrease accordingly. Furthermore, the throughput would decrease more with high frequency of maintenance on the cone crusher."

Jan 1, 2019

By William James Kempson

This paper discusses ore handling systems in shafts. These are considered from the loading facility at shaft bottom all the way through to the discharge mechanism in the headframe. These systems will be discussed from the following perspective: i. Intrinsic safety of the systems ii. The efficacy of the systems to perform consistently iii. The maintainability of the systems iv. Overall system cycle times Particular emphasis is placed on the following specific areas: 1. The Shaft Bottom Loading Facilities The various shaft loading systems currently in use are discussed, the selection parameters surrounding these are quantified and the specific selection criteria are outlined. 2. The Various Skip Configurations In this section the various skip configurations in use around the world will be described and the specific design details associated with these will be highlighted. The advantages and disadvantages of these systems will be compared and the overall efficacy of these will be discussed. 3. The effect of the loading and skip configurations on the Load Cycle Times. The overall cycle time which can be achieved by a shaft system is strongly dependant by the speed and efficiency with which the ore can be loaded and transported out of the mine. The potential of the various systems to be optimized will be discussed. The emphasis of this paper is to highlight the lessons which have been learned with respect to ore transport system design and provide a common basis against which these can be compared in future applications.

May 1, 2013

By J. A. Ressinger

"The purpose of this paper is to discuss some of the differences between various methods of excavating and loading as they relate to mining operations. The intent is not to provide ""pat"" answers, but instead to raise some questions and set forth some reasonable guidelines.Specifically, the paper deals with the differences and relative merits of power shovels versus rubber-tired front-end loaders - or, carrying this further, comparing what could be called ""stationary"" loading or excavating devices to ""mobile"" types."

Jan 1, 1972

By Lorrie Fava

Two needs in the mining industry, to enable overall process improvements, are open systems and network connectivity in underground mines. The Pando project, a collaboration between Symboticware, Vale and Xstrata Nickel, and supported by CEMI, addresses these issues, and leverages the solution platform to deliver intelligent applications. An open system is one that uses publicly available standards for its key interfaces. Vendor-neutrality and ease of information flow are two main benefits that result from the use of open systems. By facilitating the interoperability of systems, open systems allow information to be available when and where it is needed for decision support. Network connectivity in underground mines is typically limited, with hotspots in strategically chosen areas that are relatively static. Mobile equipment moving through a mining work cycle experiences intermittent connectivity; in this situation, seamless remote equipment monitoring is impossible. The Pando project establishes an open technology platform, adhering to the IREDES and OPC UA standards. It enables the collection and integration of information generated by mobile equipment? seamlessly while there is a network connection, and as a store-and-forward gateway to manage intermittent connectivity. The platform capabilities are leveraged to support embedded intelligent applications. This open platform, the SymBot, is a rugged hardware and software device. The platform complies with open standards for industrial automation and systems interoperability. The SymBot platform is capable of providing advanced real-time decision support at the device level, and is designed to be remotely configurable. Applications being developed through the Pando project include engine monitoring, a dynamic load weighing system, machine location monitoring and automated activity monitoring including production and maintenance reporting.

Oct 1, 2010

By T. D. Chatwin

While new jobs and taxes are major incentives for support of mining, stakeholders must also be assured that current jobs, resources and environment will be protected. Mining companies can help achieve stakeholder support by frankly addressing Acid Rock Drainage CARD) issues. To prevent ARD, miners must begin early in the mine life-cycle to develop an ARD management plan and integrate it into the mining operation. As this proactive preventative program is initiated, mining companies also need to engage and collaborate with stakeholders to insure that their expectations and needs are met. Stakeholder engagement is enhanced as mining companies emphasizes the value of clean and available water for current and future generations.

Jan 1, 2011

By Simon P. Fricker

Gold drugs have been used for the treatment of rheumatoid arthritis since the mid 20th century as disease-modifying antirheumatic drugs (DMARD) class. Methotrexate is often the preferred DMARD, and with the advent of new therapies gold drugs are now used infrequently. Since the introduction of auranofin in 1985 there has been no new clinically approved gold drug. In spite of this apparent lack of progress there has been a great deal of interest in the use of gold compounds for cancer therapy and early promising indications were achieved with a gold phosphine complex [Au(dppe)2]Cl. This compound was not entered for clinical trials, however, due to problems with cardiotoxicity highlighted during pre-clinical toxicology studies. Gold(III) is isoelectronic (d8) with platinum(II) and likewise forms square planar complexes. It is therefore tempting to speculate that such complexes would have similar antitumor activity to cisplatin. In order to stabilise the gold(III) oxidation cycloaurated complexes were synthesised with a single mononegative bidentate ligand, damp, (2-[(dimethylamino)methyl]phenyl), and two monodentate anionic ligands e.g. Cl or acetate. The damp ligand forms part of a five-membered chelate ring. The monodentate ligands are readily hydrolysed and are available for substitution. These compounds had limited anti-tumor activity in in vivo against human tumor xenografts. Mechanistic studies indicated that these compounds had a different mechanism of action to cisplatin. An alternative molecular target for these compounds is biologically important thiol-containing molecules such as the cysteine protease cathepsin B. Modifications were made to the Au(III) damp structure to give compounds with a six-membered chelate ring. These compounds were shown to be inhibitors of cathepsin B. Compounds were also tested for cytotoxicity against a panel of human tumor cell lines. Three compounds were selected for further evaluation against a human colon tumor xenograft. The compounds showed modest anti-tumor activity but with no marked improvement over the parent Au(III)damp complexes. Initial indications are that Au(III) compounds targeted against disease-specific thiol-containing biological molecules have potential as drugs, particularly for cancer. However, further work is required to produce a target-specific drug with a suitable pharmacological activity and toxicity profile.

Oct 1, 2003

Cambior has been involved in the Guiana Shield since 1990, first in Guyana and then in Suriname starting in 1994. This paper presents the history of Omai Gold Mines Limited in Guyana, where commercial production started in 1993 after an investment of US $150 million. In 1995, the mine was expanded in order to increase the milling capacity to 21,000 tonnes per day. After ten years of production, approximately 3 million ounces of gold have been produced. Building on this experience, Cambior became involved in Suriname with the Rosebel Project. A US $95 million pre-production program started in the fourth quarter of 2002, and the mine should be in commercial production early in 2004.

May 1, 2003

By Alfred W. G. Wilson

THE ultimate purpose of the Chemical Manufacturer is to produce consumer products which can be sold to customers. Such production and sales can be continued only if the operations yield a profit to the manufacturer and if the products meet the requirements o the consumer--bath parties to the transaction must be satisfied. There are vast numbers of consumer products, made by chemical pro-cesses. The production of some of these ultimate products may involve the use of several intermediate chemicals, applications of few or many different processes, and the utilization, somewhere in the series of operations, of a variety of raw materials. On the other hand, some ultimate products have a very simple chemical history between raw materials and end products. There are no chemical products in use which are completely independent of the mineral industry. For many, the association is direct and obvious; for others, it may be indirect and even obscure. Analyses of the process and raw-material ancestry of a very large number of consumer products would suggest that many products are derived from Industrial Mineral products directly, that there are many in which the connection is indirect, and that there are only a few products with which industrial minerals are not in some way or other associated. The vast majority of the more important chemical products, and especially the basic chemicals from which other products are made, are directly dependent for their production upon Industrial Minerals or their derivatives. In the preceding part of this paper, for each raw material mentioned some references have been made to the leading chemical products based on this material. This, however, is only part of the story, because in most cases the consumer product can be made from any special raw material mentioned only by the use of other materials or chemicals made from them. The production of consumer chemicals is really possible only through an intricate interlocking of processes, materials, and apparatus.

Jan 1, 1940

By M. Moghadami

Design and construction of underground openings are associated with many uncertainties with regard to input data. In the construction process of underground openings various levels of risks exist and these affect the safety and profitability of the project. The development of underground openings can be broadly categorized into three major phases of data collection, design, and construction. A significant level of uncertainty is associated with some of the key parameters involved in the aforementioned development phases. Moreover, it is very difficult to evaluate and quantify the effects of uncertainties on the underground project construction process. Additionally, the interactions between important risk elements are typically not well understood. The intention of this study is to develop a general risk model for underground opening projects located in soils and weak rock masses. The goal of the research is to identify and quantify important geotechnical risk elements. Moreover, a weighting procedure will be proposed for the identified risk elements. Finally, all important risk elements will be assembled into a general model with emphasis on geotechnical parameters. The final objective of this study is to apply the proposed model to a real underground project scenario and verify it for actual field conditions. The proposed model, once calibrated properly, will provide a useful support tool for the decision making process.

Aug 1, 2013

By M. A. Keogh

This paper reviews the physical properties that make low-density polyethylene the most practical and economical material for launder• fabrication in the majority of mine and mill applications. The basic design features and use of other launcher• materials are also discussed.

Jan 1, 1976

By Shoma Sinha, Nirmal K. Sinha

Deformation in a material at any temperature is known to consist of two major components - a reversible (elastic) part and an irreversible part (often called plastic). What is not universally known is the fact that at high temperatures greater than about 0.4Tm, where Tm, is the melting point in Kelvin, the reversible part includes not only elastic but also a delayed elastic (recoverable but time dependent) component. A very simple computational model is presented here for a constant-strain stress relaxation test (SRT) on the basis of a three-component constant-stress rheological equation derived from strain relaxation and recovery test (SRRT) data. It is shown that the rapid stress reduction during the early periods of relaxation when the stresses are high is governed primarily by delayed elasticity irrespective of the imposed strain level. This is in contradiction to the popular concept prevailing today. The asymptotic approach to a quasi-stable stress rate at longer times and lower stresses is, however, controlled by viscous flow (power-law creep). The validity of the theory is examined by comparing the predictions with experimental results obtained for a titanium-base alloy Ti-6246 at 0.45Tm.

Jan 1, 2004

By Kevin J. Melong

"Redpath Canada Limited and joint venture partner Thyssen Mining and Construction Canada have recently completed the sinking of the Scissors Creek service in Saskatchewan through its joint owned company, Associated Mining Construction (AMC). The Scissors Creek service shaft was sunk at Nutrien’s Rocanville mine. The following paper outlines the shaft sinking plant and the methodology related to sinking and shaft lining. KEYWORDS Hydraulic shaft jumbo, Hydraulic shaft mucker, Potash shaft sinking, Shaft lining, Sinking galloway INTRODUCTION The sinking and lining of shafts at mines to access mineral deposits has always been one of the great mining challenges for owners, engineers and contractors. Over the course of history in Canadian mining, the sinking of potash shafts through the notorious Blairmore formation of Saskatchewan has proved to be some of the most challenging shaft sinking projects on record. There is no doubt that today’s shaft sinking business demands the utmost in safety performance while delivering projects within schedule and budget. Given these requisites, Redpath and TMCC (executed under the joint venture company, Associated Mining Construction or AMC), were taxed with developing the shaft sinking system to deliver this program in the safest and cost effective manner, with due regard to schedule and quality. Traditionally the potash shafts sunk in Saskatchewan involved a significant level of manual labour, owing to the methodology of excavation by means of chipping the frozen shaft sections with hand held pneumatic machines, and manually placing tubbing segments or steel liners of the shaft lining system. Most certainly, the AMC team wanted to make a step change from those earlier sinking programs and develop systems for sinking this potash shaft that removed the high level of manual work, thus making this project inherently safer, while endeavoring to sink more efficiently. With that in mind, the team embarked on a design program to improve its overall shaft sinking systems without the requirement for excessive capital and methodology flexibility to adapt to potential changing conditions expected to be encountered during shaft sinking. This was especially important should the new approach be met with less than expected success, and retrofitting of the system was required. The concepts were developed to provide for a much improved work environment, while easing the manual labour burden on the workers with innovative equipment and approach to the work."

Jan 1, 2019

By Euler De Souza

"The uninterrupted operation of a ventilation system is critical to ensure the mine meets its scheduled production and, as important, is vital to the health and safety of all personnel working underground. Those operating the mine ventilation system must have fundamental engineering training in the art of fluid dynamics and have a good comprehension and control of the mine ventilation network. Ventilation management by untrained and inexperienced personnel may result in serious consequences when the system becomes ineffective. This paper shares observations and experiences pertinent to the occurrence of upset conditions as a result of the improper design and operation of mine ventilation systems. A series of real life case studies are presented to describe disruptions to mine ventilation systems and the gradual deterioration of system operational efficiencies leading to eventual failure. Special focus is given to mistakes made and on the resulting serious consequences. The case studies also demonstrate how each upset condition was resolved, permitting the mines to safely resume production activities.INTRODUCTIONThe ventilation of operating mines is a continuously changing and evolving system; upset conditions will occasionally occur, but should be promptly resolved in order for the system to function properly, according to design, and in compliance.Those designing, managing or operating the mine ventilation system must have pertinent training and have a good understanding of fundamental ventilation concepts to be able to devise and implement engineering solutions to day-to-day challenges. Realistically, the operator must also have extensive practical experience and be able to effectively apply operating procedures, design criteria and ‘best practices’. They must be able to, on a daily basis, evaluate the mine ventilation system, determine and locate any problems, understand the causes of each problem, find a solution, and promptly and efficiently correct those problems.Ten case studies are presented to demonstrate how fundamental design or operational mistakes can lead to adverse conditions or to catastrophic consequences, how detailed on-site engineering assessments can be employed and how simple, low cost, engineering solutions can be implemented to successfully resolve the issues and return the ventilation system to compliance, permitting the mines to safely resume production activities."

Jan 1, 2019