Search Documents

By Fathi Habashi

"Hydrochloric acid (HCl), although more expensive than sulfuric, find uses as a leaching agent in reactions involving iron oxide. The reason for this substitution was the discovery that oxyhydrolysis of ferrous chloride by which HCl can be recycled economically. This avoided the pollution of the environment by ferrous sulfate. It was found further that the rate of leaching of sulfides is faster when HCl is used as compared with sulfuric apparently due to the formation of aqueous chlorine. In case of refractory gold ores, HCl leaching under pressure avoids the use of cyanide solution since gold chloride is produced which can be recovered by standard methods. Hydrochloric acid find also uses in the leaching of scheelite and apatite but its use in leaching clay and anorthosite is questionable.INTRODUCTION Sulfuric acid is the cheapest acid and is used as a leaching agent in many hydrometallurgical processes. However, hydrochloric acid (HCl), although more expensive since it is prepared by reaction of sulfuric with sodium chloride, has replaced sulfuric acid in many reactions involving iron oxide. It replaced sulfuric acid for the first time in 1960s in pickling of steel because of pollution problems (Habashi, 2000). Ferrous chloride produced in pickling can be economically decomposed to ferric oxide and HCl according to:2FeCl2 + 2H2O + 1/2O2 ? Fe2O3 + 4HCl (1)which also shows that the acid can be regenerated but ferrous sulfate cannot be economically decomposed to recover sulfuric acid for recycle. Since then, HCl has been used in many leaching processes. Hydrochloric acid is a corrosive acid and is usually handled in rubber-lined equipment. REGENERATION OF HYDROCHLORIC ACID Regeneration of HCl is conducted in fluidized bed or in spray roaster Fluidized bed oxyhydrolysis In a fluidized bed, ferrous chloride solution is introduced onto a bed of hot ferric oxide where heating is provided by the hot fluidizing combustion gases (Figure 1). The solution is fed on top of the bed of oxides. The liquid feed wets the outer layer of the hot oxide particles and is quickly evaporated to form a layer of new solid oxide on top of the existing oxide, thereby producing dense homogeneous particles."

Jan 1, 2017

By W. Lamb

Feed Preparation ? Five primary parameters affect the screening efficiency ? Ore characteristics ? Operational characteristics ? Screen characteristics ? Water addition and washing ? System design

Apr 1, 2005

By G. W. Diehl, G. A. Griffiths

"Gentlemen, one week ago, I attended the University of Minnesota's Annual Symposium on Mining, in Duluth. A good part of this symposium was dedicated to mill linings of rubber.At this symposium, three mining companies published results from long time full scale tests with rubber linings in mills at four different mines. These were the Republic and Empire Mines of Cleveland Cliffs Iron Company, the Groveland Mine of Hanna Mining Company and the Eagle Mountain Mine of Kaiser Steel Corporation. These papers will be printed in due time and I will not endeavour to relate their full contents, let me only say that in three of the plants, the linings were found to be very economical compared wi.th steel, and that these three are converting over completely to rubber linings, while the fourth, Empire Mine, reported no economical results as far as the shell lining goes, whereas the grates showed promise of becoming economical. The authors of the Cleveland Cliff's paper, however, stated that design improvements in the rubber lining possibly could result in an economical lining also for Empire Mine.That rubber linings in mills, in most cases, show better wear life than steel linings, is known by most of the audience. But, one thing that has not before been disclosed by the endusers is the effect of rubber linings on the grinding economy. All three papers mentioned above reported no change in capacity or grind and two of them reported a decrease in power consumption per ton ground. Hanna Mining reported an average decrease over a three year period for one mill of over 10%. This, of course, puts the economy of a rubber lining in a completely new light. Finally, a point of interest at this meeting was that all three papers emphasized the design aspect, Thus the industry has acknowledged what I believe to be a very important fact - the design of a lining is often more important than the material it is made of."

Jan 1, 1970

By Robert B. Parsons

"During hard times, the focus on tax issues makes a slight change in direction. Mining companies contemplate the tax treatment of transactions and circumstances which are the product of a difficult financial environment. Some of these issues are discussed in this month's edition of Tax Notes.Every industrial sector in Canada is undergoing a major restructuring of some form, and the mining industry is not an exception. The longest recession since the Great Depression continues to affect the economy. Mining firms seek to bring their debt/equity ratios into line, and try to replenish depleted retained earnings by selling assets. This month, Tax Notes briefly examines some of the tax issues which are generally encountered during the course of such a restructuring process.Debt SettlementOne question which commonly arises during hard times concerns the tax treatment of a "" gain "" realized by a debtor on the settlement of a debt. Consider, for example, a simple situation where a creditor wants to protect itself from further losses, and makes a deal with the mining company to accept a cash payment of $8 million in full settlement of a $10 million loan. In financial terms, the debtor has made a $2 million gain on the settlement of the debt. What is the tax treatment of that gain?The Income Tax Act (the Act) contains provisions in section 80 of the Act and in section 5400 of the Income Tax Regulations which deal specifically with this question. First of all, it is noted that the $2 million gain is not brought directly into income for tax purposes. However, as indicated below, the gain could affect the debtor's income indirectly to the extent that certain of the debtor's tax pools must be reduced by the amount of the gain."

Jan 1, 1993

By A. Henk, C. M. Aruffo, K. Fischer

"Geomechanical reservoir modeling offers a valuable tool to predict tectonic stresses, in particular the local perturbations in orientation and/or magnitude which occur at lithological boundaries and faults. The paper presents a workflow for building and calibrating such geomechanical models. The numerical simulations are based on the Finite Element method and can range from field-scale models to smaller, highly detailed submodels of specific fault blocks. The approach considers the reservoir-specific characteristics with respect to subsurface geometry (lithostratigraphic boundaries, faults), mechanical properties and ambient stress field. During the subsequent calibration stage calculated stresses are compared to stress data actually observed in borehole data. Poorly constrained input parameters are iteratively modified within reasonable limits until a satisfactory fit between calculated and measured stresses is achieved. This validated model can then be used for stress predictions between wells and in undrilled parts of the reservoir, respectively. The workflow is applied to two case studies - a large gas field in Northern Germany and a CO2 sequestration project in Australia – to test and illustrate its practical value. INTRODUCTIONDetailed knowledge of the tectonic stress field is crucial for the optimal exploration and use not only of conventional and unconventional hydrocarbon reservoirs, but also for deep geothermal reservoirs, carbon capture and storage (CCS) projects as well as underground mining and nuclear waste repositories. Any reliable stress prediction is hindered by the observation that the magnitude and orientation of the stress field can vary significantly – not only in time, but also in space. Such spatial stress variations comprise all scales, i.e., from the scale of lithospheric plates down to the grain-scale. On the reservoir- and fault blockscale, the local stress field can be influenced by faults and different mechanical properties of lithologies (Sassi & Faure, 1997). The resulting variations in stress magnitude and/or stress orientation are commonly referred to as stress perturbations and give rise to a unique, reservoir-specific stress pattern (Yale, 2003). Thereby, local stress fields can deviate by up to 90° in orientation and several tenth of Megapascal (MPa) in magnitude from regional trends."

Jan 1, 2015

By Emmanuel Henry

Hanging wall deformation monitoring at the Kiruna Mine is a major concern for Luossavaara- Kiirunavaara AB (LKAB) since underground production is deepening towards the Kiruna Town. In the quest for more effective monitoring techniques, LKAB decided to evaluate satellite-borne Synthetic Aperture Radar (SAR) interferometry?s ability to monitor ground subsidence by generating continuous deformation maps from satellite radar images. While adopted by other geoscience-related industries, SAR interferometry is still relatively untested in the Mining industry. This paper describes how subsidence is actually monitored on the Kiruna Mine?s hanging wall and gives an insight on SAR interferometry?s principle. The encouraging results are discussed as well as the technique?s benefits (continuous deformation mapping, low cost, fast, etc) and limitations (sensitivity to snow and vegetation cover).

May 1, 2003

By A. Rahimi

Refractory castables based on alumina-silicate aggregates are commonly used in casting wheel components and launders. In this research the recycling process of waste magnesia chrome bricks for production of refractory castable lining for launders and casting wheel ladles at Iranian Sarcheshmeh copper complex (I.S.C.C.) is discussed. The smelting plant of ISCC consumes 4,000 tons refractory materials and produces 2,000 tons waste refractories annually. In order to reduce the environmental pollutions and gain the economical advantages, the recycling of waste refractories proved to be a solution [1]. In ISCC, 800 tons alumina or alumina-silicate refractory castables are used for linings of anode furnace ladles and launders annually [2]. In the present work, the spent bricks from reverberatory, converter and anode furnaces were analyzed in term of microstructural changes from hot zone to the cold end to evaluate the changes in texture and chemical composition. Different formulations based on recycled magnesia chrome aggregates and various particle size distribution and cement content were tested. Economic recycled magnesia chrome refractory mixture was prepared after crushing and sizing the non-deteriorated regions of wasted bricks. After evaluation of physical and mechanical properties of samples, one ton of refractory castable was prepared and successfully installed in the casting wheel ladles.

Jan 1, 2007

By A. R. Laplante

"In this paper, the performance of the Knelson Concentrator and of the batch and continuous Falcon Concentrators are compared. The units are based on different operating principles, and as such they perform quite differently. The Knelson yields very high free gold recoveries over a wide size range of both the recovered and rejected species. It is ineffective in recovering very fine ( <15 µm) or flaky gold, as encountered in flotation feeds, concentrates or tails. It is the: preferred unit for gold recovery from grinding circuits. The batch Falcon is effective in the fine range, typically less than 37 µm for gold. Its recovery zone is quickly saturated when there is significant heavies in the feed. It works best as a pre-concentration unit. The continuous Falcon is a versatile unit which is capable of recovering fine heavies (density down to 5 g/cm3 ), especially from coarser gangue. INTRODUCTIONThe purpose of this presentation is to describe the mode of operation of two Canadian centrifugal concentrators, the Knelson and Falcon. It is hoped that it will prove informative to prospective users in the selection, testing and optimization for applications of either machine. The work is based on testwork both in Canadian mills and at McGill. I am indebted to many colleagues at these locations. Appropriate references will be made to articles further describing the work, either already in the open literature or in preparation.Although this work is meant to be more practical than scholarly, it is appropriate to begin by considering how the two units achieve selective recovery. This will become useful in establishing a suitable testing methodology, which will then be described, and interpreting typical results. In the last section I will attempt to define appropriate applications for the two units. This is a thankless task, as I am likely to miss some applications or to make projections based on partial results, as much of the work is still in progress. In deference to the reader and both manufacturers, areas where reasonable doubt still remains will be identified."

Jan 1, 1993

By V. I. Peresypkin, A. Y. Lein, N. S. Bortnikov, Yu. A. Bogdanov

"Abstract - The lipid component in hydrothermal deposits of the Logachev vent field, at 14°45_N of the Mid-Atlantic Ridge (MAR) and Broken Spur vent field, at 29°N of the MAR, was studied. Biochemical, gas chromatographic (GS), and molecular mass methods (GC-MS) research established the mixed nature of the organic matter (OM) including phytoplanktonogenous, chemosynthesized lipids, and lipids of questionable origin. Specific local conditions around the sulfide ores of the black smokers (absence of free oxygen and presence of reduced copper, which prevents OM degradation) facilitate the preservation of biogenic material, including bacteria. The main differences between the lipid compositions of the hydrothermal deposits of these two vent fields relate to the variable nature of hydrothermal circulation systems.At the 14°45_N vent field, high-temperature hydrothermal fields are forming due to the reaction of sea water with upper mantle ultrabasic rocks during serpentinization (a deep hydrothermal circulation system). High pressure and temperature (>400°C), a reducing environment and the presence of various metal oxides are favorable for the abiogenic synthesis of CH4 and oil hydrocarbons (HC). At the Broken Spur vent field, hydrothermal deposits are forming above axial crust magma chambers due to the interaction of sea water and basalts (an axial hydrothermal circulation system). Abiogenic synthesis of HC also occurs in this situation, but to a considerably lesser extent."

Jan 1, 1999

By H. Clare Horwood

"In the Red Lake area in northwestern Ontario the relationships between general structures and structures containing ore deposits are among the most unusual and most interesting of any in the Precambrian Shield. The more important orebodies, which are in the central-eastern part of the area, occur in a variety of rocks on the northeastern, eastern, or southeastern sides of a series of granite stocks. Other deposits in the western part of the camp also are structurally associated with granite masses .The relationships were determined in the course of general and detailed geological mapping by detailed analyses of the fracture patterns in the rocks adjacent to the orebodies. In every case it was found that the structures containing the ore were produced by compressive stresses from the direction of intrusion of the granite masses( 2).The Red Lake area lies in the Patricia part of the district of Kenora and is accessible by boat from Hudson or by airplane from Kenora, Sioux Lookout, or Winnipeg. A road from Vermilion lake, on highway No. 17, was opened in August, 1947.The first discoveries of mineralization in the area that proved to be of economic importance were made in 1925 by Lorne Howey and George McNeely for Haileybury interests and by Ray Howey and W. F. Morgan for Mcintyre-Porcupine Mines, Limited. Both prospecting ventures were organized because of information presented by Bruce(l) in his map and report for the Ontario Department of Mines. The discoveries, which were both along the same structure, a quartz porphyry dyke, later developed into the Howey and Hasaga gold mines. Other discoveries were made at intervals as a result of prospecting and development work on ground staked for its location."

Jan 1, 1954

By A. Poor Zaeif Doost

With columns being installed in rougher section at Miduk Copper Complex, the rougher feed mainly reports to rougher-scavenger cells. To evaluate the efficiency of regrinding circuit, we conducted flotation experiments on samples of the feed and the products of the regrinding circuit. The grade difference of these products at 85% recovery was considered as the efficiency index. Results show that, with weight recovery of the rougher-scavengers the efficiency of the circuit increases. Exclusion of the rougher-scavenger concentrate from the feed to the regrinding circuit, resulted in an increase in the efficiency index from 10.12 to 17.6%.

Jan 1, 2012

By J. C. Ingles

"A new technique is in the process of revolutionizing inorganic chemical analysis. Galled atomic absorption spectrophotometry, it combines the use of a special light source, a flame, and the equipment of conventional spectrophotometry, to provide a quick, reasonably accurate method for the determination of a large number of elements.This paper outlines the principles on which it is based, describes the commercial instrumentation"" available for exploiting it, and. summarizes current applications in process metallurgy."

Jan 1, 1966

By H. D. B. Wilson, W C. Brisbin

The Thompson-Moak Lake nickel belt lies along the root of a Precambrian mountain range of the island-arc or alpine type. This range coin-. cides with the boundary between the Superior and Churchill blocks of the Canadian Precambrian shield. The nickeliferous peridotites and nickel ores occur along a negative gravity strip, which also coincides with strong thrust faulting and the axis of greatest deformation of the mountain range. Similar structures and highly nickeliferous peridotites occur in present-day island arcs. Much of the belt is covered by Paleozoic rocks, but a length of 270 miles may be explored by present-day methods. Nickel deposits have been located along 60 miles of the belt. The length of the favorable structure and the size of the known deposits suggest that this will be one of the world's major nickel regions. The regional gravity anomalies, which consist of a branching negative strip bordered by two positive strips, are best explained by major warps of a crust consisting of a granitic and basaltic layer. The ore deposit

Jan 1, 1961

By H. L. Cameron

Introduction Since the beginning of gold mining in Nova Scotia in the year 1860, the biggest problem o the mine operators has been to find and follow the ore zones in the narrow quartz veins. It was early recognized that all veins were not gold bearing and that, in those that were, the commercial ore was confined to limited zones. A large number of geologists and mining engineers have been interested enough to give time and thought to the problem, but, until the last four or five years preceding World War II, they were handicapped by lack of exact data from mining operations. The necessary data could only be obtained by daily checking of underground operations. Such daily checks were instituted at a number of mines during the period 1935-40 and, in every case, were successful in delimiting the ore zone or zones for the particular mine. The present paper deals with the results of this work as applied to practical ore finding. It is an attempt at extrapolation, from observations in the four districts with which the writer is personally familiar, co other districts in which similar conditions or structures are reported.

Jan 1, 1947

By M. A. Perras, H. A. Kasani, G. Walton

The development of an underground repository for the storage of spent nuclear fuel relies on a multi-barrier system to isolate the used fuel from the environment – ultimately, the biosphere. These barriers include engineered copper and steal canisters, dense bentonite, and the natural rock as well. In order to reduce the potential flow pathway along the excavation induced damage zone, various slots perpendicular to the excavation axis have been proposed. These slots are called cut-off seals and generally are filled with bentonite as it has high swelling potential and very low permeability. Many different geometries have been proposed, but clear guidelines on the selection of the optimum geometry have yet to be developed. In order to assess the optimum geometry, three shapes have been selected for this numerical study, including a trapezoid, a triangle, and a thin rectangular slot. The cut-offs were modelled for a conceptual shaft constructed in the Queenston Formation from Ontario over a stress to strength ratio that has been found at many underground research laboratories. It was found that the excavation of a triangular and thin slot cut-off had the smallest increase in the damage as quantified based on the extensile volumetric strain within the plastic yield zone. Both shapes showed an increase in the damaged zone by 13 cm at a stress to strength ratio of 2.75. The trapezoidal cut-off damage zone increased by 20 cm at the same stress to strength ratio. Further study is required to better define the optimum cut-off shape for wider variety of conditions and other geological formations.

Jan 1, 2020

By 000-900-009-492

The flotation has been and is still the most widely used mineral concentration method. Because of its complexity, the flotation process required the development of robust control strategies which was facilitated by the introduction of on-line sensing instruments such as x-ray fluorescence (XRF) on stream analyzer (OSA), gamma density gauges and electromagnetic flowmeters. The interest in developing control strategies has persisted because the benefits to be gained in terms of improved metallurgical performance are substantial. As the flotation control becomes more and more difficult due to the emergence of low grade and complex ore cases, other control strategies have to be introduced. Froth based control is one of the emerging useful control strategy This paper will focus on the state of the art in the on-line froth characterization as obtained by numerical image analysis. The technology of machine vision provides a novel solution to several of the problems encountered in conventional flotation systems for monitoring and control, and constitutes a powerful tool for the investigation and interpretation of the effect of various flotation parameters as driven for the froth phases. Copyright @2001CIM

May 1, 2001

By H. Wotruba, L. von Ketelhodt, M. Kowalzcyk, M. Robben

ABSTRACT Decreasing reserves, water shortages, increasing energy costs, and environmental and social constraints are challenges to the gold mining industry that must be met with innovative machines and methods. This paper introduces the principles of sensor-based sorting and installations that demonstrate the technical and financial viability of the method. The scenarios discussed highlight the potential and advantages of this dry processing technology that requires little infrastructure. Case studies are presented for different ore types using optical- and X-ray transmission–based sorting. Current research is discussed in terms of the potential of near-infrared spectroscopy and X-ray fluorescence sorting for gold applications.

Jan 1, 2013

By R. C. Wallace

In the early explorations of the Northwest, the search for minerals played a not inconsiderable part. The first episode had its disillusioning sequel. Sir Martin Frobisher, in 1576, sailed up that bay in Baffin land now known as Frobisher bay, thinking that he had the coast of Asia on his right hand. He brought back from this expedition a piece of &apos;black earth&apos; from Hall island, from which an alchemist by coaxing nature, or his own conscience, obtained gold. A second expedition of three ships was fitted out in 1577, and a third of fifteen ships in 1578. The ships were loaded with this &apos;black earth&apos;, which on subsequent investigation was found to be worthless, and interest in minerals for the time being ceased. In 1612 Hall and Baffin went in search of a gold mine near the Arctic circle on the west coast of Greenland, reported to be worked by the Danes. They found old workings, but no ore. To come nearer the Hudson Bay area, it is noteworthy that the charter granted by Charles II to the Hudson Bay Company in 1670, as a result of the explorations of Radisson and Groseillers, was given "-in consideration for their having at their own cost and charges undertaken an expedition to Hudson bay in the northeast parts of America, for the discovery of a new passage to the South sea, and for the finding of some trade for furs, minerals and other considerable commodities, and of their already having made by their undertakings such discoveries as did encourage them to proceed farther in pursuance of the said design, by means whereof there might probably arise great advantage to the King and his Kingdom - ".

Jan 1, 1925

By M. Seyed Ahmadi

This study investigates the role of nitrogen gas injection in the dissolution rate of Si into liquid Al. A unique revolving liquid metal tank was used, with a capacity of 50 kg of liquid Al. Experiments without gas injection have shown that the dissolution of Si increases as the bath superheat and the tangential velocity of the liquid Al increase. When injecting nitrogen gas at flow rates between 0-5 lit/min in the vicinity of the solid Si, results so far clearly show greater dissolution. In addition, results on the role of the gas flow rate relative to the position of the nozzle are presented and analyzed.

Jan 1, 2011

By N. P. Hristov, L. V. Kuzev

"A simulation study of the fill factor of a drum mill was conducted using two types of grinding media: balls and tetraballpebs. Each medium was composed of equal number of grinding bodies having equal weight but different shape. The difference was in the density of the two grinding media.Standard spherical grinding bodies (balls), which were used in practice, and equivalent (by weight) grinding bodies in the shape of spheroidal tetrahedrons (tetraballpebs) were studied. The simulation was conducted in a module of a 1.2 m diameter drum mill, whose length exceeded twice the diameter of the corresponding grinding body. The grinding balls had a few percent (3 to 6) higher fill factor than the grinding tetraballpebs in the same shell.Vertical sections of the grinding medium were taken across the studied shell module along its axis. They showed the location of each grinding body in the fill volume. Defects in the packing of the grinding bodies and the contacts between them and with the inner surface of the shell were also show. Differences in the contact points of the balls and the tetraballpebs were noted. For the tetraballpebs, we observed contacts both between the spherical surfaces and with the edges and vertices of the grinding bodies.The topography of the grinding media is shown visually.INTRODUCTIONThe grinding balls have been studied extensively. It is the traditional grinding medium in ore processing industry. The parameter characterising the grinding medium is its density. It is the mass of the grinding medium per unit of volume. The parameter may have a range of values. It depends on:• The physical properties of the material they are made of;• The shape of the grinding body;• The dimensions of the body;• Size distribution of the grinding bodies in the grinding media.In comminution, the fill factor of the mill shell is the process parameter that is representative of the grinding medium. Some publications have indicated the disadvantages of ball grinding. For example, Wu, Xiang, Glen, and Duan (2008) note in the analysis of the mechanism of grinding that the balls are not the best grinding media and disadvantages include among others:• Easy over-grinding resulting from the point contact between the balls;• Attrition surface is the smallest in the grinding media;• Poor selective exposure of minerals resulting from the accidental and often significantly more powerful impact on the feed;• The grinding efficiency drops as the fineness of grind is increased;In the Handbook of mineral processing, Polkin (1950) noted that the shape of the grinding bodies determines the volume of the void spaces therein and therefore the shape affects the grinding efficiency per unit of volume of the grinding medium."

Jan 1, 2016