Search Documents

By Q. Li

"The precursor of In2O3 was prepared by hydrolysis precipitation/hydrothermal method using In(NO3)3 solution as the feed material and ammonium hydroxide as the neutralizing agent. The crystallinity, morphology and particle size of the products were characterized by SEM, XRD, BET and LPSA. The results showed that the hydrolysis product consists of an aggregate of cubic In(OH)3 particles with a short rod morphology. In the hydrothermal process, the structure, morphology and size of the particles changes through the mechanisms of Ostwald ripening and phase transition, respectively. When the hydrothermal temperature was less than 280 ?, the Ostwald ripening process took place, which changed the morphology of the particles from short rods to cuboids through dissolution-recrystallization. When the hydrothermal temperature was higher than 280 ?, the processes of Ostwald ripening and phase transition took place successively. Firstly, the morphology of the particles changed from short rods to cuboids through Ostwald ripening, and then, the phase transition from cubic In(OH)3 to orthorhombic InOOH occurred and the morphology of the particles changed from cuboids to polyhedron. INTRODUCTIONDue to its excellent electrical conductivity and optical transparency, indium tin oxide (ITO) film has been wildly used in flat-panel display, solar cell, antistatic coating and EMI shielding (Medvedovski et al., 2008). Indium oxide powder is one of the fundamental materials for preparing ITO film. Along with the development of ITO targets of both high density and large size, high quality indium oxide powders, such as single phase, nano-size, spherical morphology and mono-disperse, have been in high demand (Nakashima and Kumahara, 2002; Betz et al., 2006; Kim et al., 2007). The main preparation methods for indium tin oxide or indium oxide powders include chemical precipitation (Nam et al., 2001; Xu and Yu, 2007), melt atomizing-combustion (Chen et al., 2000) and spray pyrolysis (Ogi et al., 2009). Among them, chemical precipitation has been preferred, since it is simple, easy to control and suitable for industrial scale-up. In chemical precipitation method, indium oxide powders were prepared through the following steps: firstly, indium hydrate precursor was precipitated from an indium salt solution by neutralization using an alkali, such as ammonia; and then, indium oxide (In2O3) powders can be obtained from the precursor through calcination (Li et al., 2006), or solvothermal method (Lee and Choi, 2005), or hydrothermal processing/roasting (Xu et al., 2005; Chen and Li, 2007), respectively. However, the indium oxide powders obtained by direct roasting are polycrystalline, dispersable with a wide size distribution (Liao, 2006). The disadvantages of the solvothermal method are high cost, complicated after-treatment processes, as well as bad performances of the powders (Udawatte and Yanagisawa, 2000). Therefore, among three methods of obtaining indium oxide from the hydrolysis precursor, the hydrothermal process/roasting method is the most feasible to synthesize high quality In2O3 powder with uniform crystallinity and size (Kim et al., 2002; Zhu et al., 2004; Xu et al., 2005; Xu et al., 2005; Chen and Li, 2007; Seetha et al., 2009). However, current research on hydrothermal process-roasting method has been limited to the synthesis of a certain ITO or In2O3 powders under specific conditions. A systematic study on the phase transition, as well as the change of the morphology and size of the particles in the hydrothermal process is still missing. In this paper, the effects of hydrothermal processing on the mineralogy, morphology and size of products were investigated. The results showed that the evolution of crystal structure, morphology and size in the hydrothermal process was affected through the mechanisms of Ostwald ripening and phase transition successively. These results are novel and have guidance for improving the hydrothermal process for In2O3"

Jan 1, 2012

By J. H. Walsh

IN THE DEVELOPMENT of procedures for the separation of minerals, the choice of reagents for flotation is frequently determined by the extent to which a given mineral is wettable by water. Measurements of the contact angle of an air bubble on wet mineral surfaces are often used in the laboratory to estimate the wettability of the surface. For the results of these measurements to be reproducible, the surface of the mineral must be polished to a mirror-like smoothness and must be free from oily contamination. Elaborate procedures for preparing mineral surfaces have been developed by Wark ( 1) and Taggart (2), and these procedures have been generally accepted as adequate for their purpose. The polishing techniques, how-ever, have certain inherent disadvantages which make it impossible to assess the effects of polishing, entrained abrasive, and adsorbed gases on the wettability of the mineral surface.

Jan 1, 1957

By Eric D. Marks

Fatalities resulting from ground workers colliding with objects and construction equipment accounted for approximately 18% of the total construction fatalities experienced in 2010. Current injury and fatality measuring methods have proven to be inadequate due to their use of passive measures of safety rather than a more active approach, such as the use of leading indicator data (also called near misses) of hazardous proximity situations between ground workers and heavy equipment on construction sites. The objectives are to create and evaluate the effectiveness of a reliable algorithm for collecting and analyzing the resulting leading indicator data from hazardous proximity situations. Numerous experiments emulating typical interactions between workers-on-foot and heavy equipment are used to evaluate the proximity sensing and detection technology. Safety leading indicator data (also called near misses) generated by the proximity sensing and detection technology during the experimental trials are used to create and assess the resulting algorithm. Results from the experiments indicate that leading indicator data generated from these systems can be processed and analyzed to identify hazardous proximity situations and incidents on construction sites.

Aug 1, 2013

By A. Iizuka

This study was aimed at separating and recovering arsenic, antimony, and tin from refining byproducts generated in a nonferrous smelter. The target byproduct was a silicate slag containing the above elements. The silicate structure of the slag was destroyed by alkali roasting, which then enabled leaching of arsenic, antimony and tin in solution effectively. Arsenic was selectively leached out by hot water after alkali roasting of the slag, while remained antimony and tin in the residue were leached out by a hot hydrochloric acid solution. However, when the solid-liquid ratio in the leaching solution was increased, hydrous gelatinous silica (gel-like silica) was formed during the hydrochloric acid treatment and filtration became difficult. Therefore, high temperature and high pressure leaching was attempted to improve the filterability of the silica leaching residue. In the high temperature and high pressure treatment, the hydrous gel-like silica was transformed into easily filterable aggregated silica, and thus, filtration became easy. By investigating the neutralization and sulfurization treatment for the obtained hydrochloric acid leachate (second leachate), it was possible to separate antimony and tin. INTRODUCTION This study aims to separate arsenic and recover valuable metals such as antimony and tin from refining byproducts generated in a nonferrous smelter. The target smelting byproduct is antimony-containing slag in this study. In many cases, alkali roasting was adopted as pretreatment for extraction and recovering valuable metals from smelting residues and wastes (Rao, 2006). For antimony-containing slag in this study, one effective method for separating arsenic is to convert arsenic to sodium arsenate (Na3AsO4) by roasting with a sodium compound and then to remove arsenic by hot water leaching. In addition, by alkali roasting, the silicate structure of the slag is destroyed, and effectively alkalizing tin and antimony is accomplished. Then, precipitating and recovering tin and antimony leached into the acid solution are considered possible by sulfurization and neutralization treatments. In this research, we conducted basic studies on the following. 1) Destruction of silicate structure in slag by alkali roasting and leachability of arsenic. 2) Conversion of hydrous gelatinous silica to aggregated silica by hydrochloric acid treatment of residues after arsenic leaching under high temperature and high pressure, as well as leachability of antimony and tin. 3) Separation and recovery of antimony and tin by sulfurization and neutralization treatments of hydrochloric acid leachate. These topics of investigation can support to consider the separation and recovery process of arsenic, antimony, and tin from antimony containing slag.

Jan 1, 2019

By Robin Perry, Claude Bazin

"Discrete transfer functions which use the grinding circuit feed tonnage to predict mass flowrates at reagent addition points in a flotation circuit were calibrated using a dynamic grinding/flotation circuit simulator. Predicted mass flow values are multiplied by reagent addition ratios to obtain actual reagent flow. The transfer functions are currently integrated into the distributed control system of Les Mines Selbaie.IntroductionThe development of adequate tools for the control of flotation processes is a continuous challenge. Since the early 1970s there have been numerous publications dealing with practical aspect of control of flotation processes. Most plants use a combination of feedback and feedforward controls to reduce the effect of the following flotation process disturbances (McKee, 1991):• changes in throughput;• changes in feed grade;• changes in particle floatability (size, liberation, surface oxidation ... ); and • deliberate changes of setpoint;Feedforward control manipulates variables such as reagent and/or air flow rate to attenuate the effect of disturbances such as changes of feed rate and mineral content. The feed forward strategy is driven by measurements of these disturbances. Feedback control is used to maintain process variables to targeted set-points of concentrate or tails grades. The feedback control action is driven by deviation from the set-point, caused by a deliberate change of set-point or disturbances.This paper proposes a method to improve feed forward control schemes by the addition of a simple model for solids transportation. The feedforward strategy considered in this paper is the ratio type, in which the manipulated variable is changed according to a predefmed ratio between this variable and the measured disturbance. A typical example is the ratio of the reagent addition to mass flow of ore.The paper reviews the state of the art in feed forward control strategy applied to flotation processes and describes the method used for predicting mass flow rates. The last section shows an application of the method in the Les Mines Selbaie flotation circuit."

Jan 1, 1994

By Juergen Antrekowitsch, Stefan Steinlechner

"Waelz oxide from steel mill dust recycling is usually sold to the primary zinc industry, where it is first charged to the roasters to eliminate the remaining fluorides and chlorides. This limits the overall amount of secondary materials which can be used because of different operating problems in the roasters. Another option, in the case where the halides are low, would be direct leaching with low or medium concentrated sulphuric acid. Unfortunately, because of the carryover of some steel mill dust, iron is also present in the Waelz oxide, reaching contents up to 5 wt.%. Since the objective is to treat the solution more or less directly by electrowinning, with only a few simple preliminary purification steps, iron in the solution is a very important factor. Various trials have been done to investigate the dissolution behavior of the iron contained in the Waelz oxide. Although the zinc extraction should reach a maximum, all other elements, especially iron, should be low. This paper describes the results of our research in this area and offers possible options for Waelz oxide utilization. There is also a focus on how other elements, present in the material, influence the dissolution behaviour of zinc and iron, and whether a loss of zinc is unavoidable, if low iron dissolution is required.INTRODUCTION One of the most important secondary zinc resources is the zinc oxide originating from steel mill dust recycling. For the treatment of high zinc containing steel mill dusts, the Waelz kiln process is the so called “best available technology” and it dominates the industry, with roughly a 90% market share. The product Waelz oxide contains mostly zinc oxide, but it also contains lead compounds and halides due to evaporation with the zinc. In addition, it contains iron and some slag compounds due to mechanical carry-over. The presence of halides limits the use of the material as an alternative concentrate for primary zinc electrowinning. Such halides can be reduced to a certain extent by washing and/or solvent extraction (see following chapter). Although lead is not troublesome and theoretically represents a second recoverable valuable metal, iron is unwanted and causes additional problems during leaching. Even though Waelz oxide is generally a highly welcome input material in primary zinc metallurgy, due to its high zinc content, it still contains halides, and in the majority of cases, the oxide must first be treated in a roasting process. Different circumstances, like accretion formation because of the lead and halogen compounds as well as unwanted cooling effects in the roaster, limit the amount of Waelz oxide which can be substituted for the primary concentrate. Another, even more limiting factor, is the allowable concentrations of chlorides and fluorides in zinc electrowinning, the last step in the primary zinc processing route (Ruetten, 2011)."

Jan 1, 2016

By A. Bendada, P. Servais, X. P. Maldague, C. Ibarra-Castanedo, C. Mohr

Infrared (IR) thermography is a nondestructive, non-contact and non-intrusive technique that allows the fast inspection of large and complex structures with limited accessibility. Pulsed thermography is particularly interesting for the inspection of aerospace materials such as composites given that, after submitting the specimen surface to a thermal front, the most common types of subsurface discontinuities (e.g. porosity, de laminations, dis bonds, fiber breakage and inclusions) can be detected with an IR camera as regions showing abnormal temperature patterns. We present first the case of an aircraft door with water ingress and surface repairs on its honey comb structure. We also highlight the advantages and limitations of thermography for the inspection of aircraft composite parts, such as edge flaps, rotor blades and speed breaks. Finally, we expose some results from a Kevlar® non-planar specimen with Teflon® inclusions at different depths and locations.

Jan 1, 2006

By T. J. Bruce, G. E. Agar, R. Stratton-Crawley

"A technique by which the design of a flotation circuit may be optimized is described and examples of the application of this methodology are given.Three interrelated criteria are defined and the application of these criteria to the selection of the optimum residence time for each stage of a flotation circuit is demonstrated. The criteria are:(1) Add no material to the concentrate that is lower in grade than the feed to that separation stage.(2) Maximize the difference in recovery between the desired mineral and the gangue.(3) Maximize the separation efficiency.Three independent systems were examined experimentally and it was shown that application of any of the criteria yielded similar results.It was demonstrated how the application of rate measurements (Criterion #2) could lead to the selection of a set of optimized times for several stages in a flotation circuit and that these could in turn be used to simulate the results of a locked cycle test. The predictions were checked against the experimental results from a locked cycle test and there was substantial agreement between the predicted and observed results."

Jan 1, 1980

By R. D. Brown

Higher employer costs and increased employee benefits will result from the current sweeping revisions of the un-employment insurance system now receiving consideration before Parliament. The new legislation, the Un-employment Insurance Act, 1971, will substantially increase the unemployment insurance costs of many employers through an increase in the level of employer contributions -generally, employer contributions will go to 1.4 times employee costs -as well as by extending coverage to many classes of employees now exempt. Under the new legislation, executives, technicians, teachers, institutional workers and others will be covered, and eligible for the higher benefits which it provides. For the first time, absence from work because of illness or accident may qualify individuals for unemployment insurance benefits.

Jan 1, 1971

By Sandra L. Mesa-Espitia, Gretchen T. Lapidus

Gold present in arsenopyrite matrices is refractory and requires highly oxidative pretreatments in order to obtain acceptable degrees of extraction. However, these release many byproducts that are harmful to the environment. In the present work, a high-grade arsenopyritic ore was pretreated with different solutions, containing hydroxide ion, EDTA, oxalic, tartaric, or citric acids, to improve gold extractions in a posterior leaching step. The pretreatments were carried out at room temperature for 24 hours with a respective ligand concentration of 0.25 M. Once completed, the residue was leached in a thiosulfate solution to quantify the effect of the pretreatment on gold extraction. Only 29% of the gold content was leached, with very slow kinetics, in the untreated mineral. However, after pretreatment with tartaric or citric acid, the kinetics improved, although the percentage of gold extraction only reached 42-45%. The highest gold recovery, with very rapid kinetics, was found with the oxalic acid or the hydroxyl ion pretreatment (70 and 62%), respectively, but also corresponded to the most arsenic co-dissolution.

Jan 1, 2014

By Rene Klymowsky, Norbert Patzelt, Egbert Burchardt, Johann Knecht

"The challenge of ""ore bodies getting steadily harder and lower in grade"" was brought to light during the first oil crisis in the 70's. Shortly afterwards, HPGRs appeared on the scene with the promise of saving energy. This combined with developments in wear protection for the rolls ushered in a period of trade-off studies that considered the HPGR as an option to improve project economics or to even make projects feasible at all.Since then, applications of HPGRs at Cerro Verde (Freeport), PTFI Grasberg (Freeport), Mogalakwena (Anglo Platinum), Tarkwa (Goldfields), Boddington (Newmont), Penasquito (Goldcorp), and others have contributed to the creation of a formidable basket of operating experience. Collected through years of successful operation, this information has been used to validate design criteria, scale-up factors and establishing a clearer picture of what ""to do"" and what ""not to do"".This paper compares results from various mining operations using HPGRs in their processing plants. Some of the lessons learnt in different operating environments are reviewed in order to support proper implementation and operation of HPGR's. Some of the development programs that have been initiated to improve wear life of the tyres and to reduce overall operating costs are reviewed. It is timely to summarize today’s experience and analyse its implications for existing and new operations"

Jan 1, 2012

Presentation Overview ?? Project Setting ? Project Context ? Challenges ?? Managing Commitments ?? Project Update ?? Maximizing Aboriginal Economic Participation in Resource Development PROJECT SETTING ?? Developed on the traditional lands of the Labrador Inuit, and the Labrador Innu ?? Courts have held that Aboriginal peoples in Canada possess special rights to traditional lands ?? Rights can include requiring resource developers to enter into Impacts and Benefits Agreements ?? Development agreement with Newfoundland and Labrador was required

May 1, 2004

By J. Bouchard, R. del Villar, A. Vazirizadeh

"Industrial flotation is a continuous and often multistage process, where particles of a given mineral species (usually the targeted one), present in different sizes, encounter a large amount of gas bubbles (normally air) to produce mineral–bubble aggregates, which are removed from the flotation device (cell or column) as a valuable product (concentrate). The bubble content inside the cell is characterized by the prevailing hydrodynamic conditions (known as gas dispersion variables), which in turn are known to influence the flotation performance. Although most researchers and practitioners agree that the relationship between the hydrodynamic variables and flotation performance exists, the lack of an adequate method foronline measuring the average bubble diameter has prevented such studies.The aim of this study is to apply appropriate hydrodynamic variables for flotation kinetic modeling (as a key feature of flotation performance) for a given introduced particle size distribution (PSD). In this regard, experiments were conducted in a laboratory flotation column (5.6 cm internal diameter for a total height of 650 cm), and mixtures of quartz (hydrophilic gangue) and talc (naturally hydrophobic mineral), classified in four different size fractions. The correlation between the flotation rate constant and given hydrodynamic variables were analyzed. Results suggest that the relative importance of hydrodynamic variables for flotation rate modeling depends on the PSD. Finally the suggested hydrodynamic variables for each of the various particle size-classes considered were used to produce single variable models for the flotation rate constant. INTRODUCTIONIndependently of the prevailing flotation conditions, the mechanisms for bubble-particle aggregation and the residence time of the phases inside the device must also be considered. In this regard, one of the most used approaches to represent the overall flotation process is as a pseudo-chemical reaction between a particle and a bubble, whose rate (at a given time) is proportional to the amount of remaining floatable species. The proportionating constant is called the kinetic constant or the flotation rate constant."

Jan 1, 2016

By Roland B. Hoag, Roger G. Webber

Sulphate concentration in groundwater is a good measure of the extent of oxidation of sulphides, provided that sulphide minerals are the primary source of the sulphate. A study was conducted near the Eustis Mine in Quebec to determine where and how the sulphate in groundwaters originated. Atmospheric precipitation is the only source of sulphate other than oxidation of sulphides, and in this study area it is equal to 0.01,. millimole per litre. The oxidation of sulphides can be divided into subsurface oxidation (mainly inorganic processes) and surface oxidation (including both organic and inorganic processes) . The maximum sulphate concentration due to subsurface oxidation of sulphides depends on the solubility of 0 2 in water and is 0.25 millimole per litre. Surface oxidation is, therefore, responsible for any amount greater than atmospheric plus subsurface contributions (0.29 millimole per litre). Surface inorganic oxidation occurs in waters with a pH greater than 15 and is controlled by the kinetics of the oxidation processes. Organic (bacterial) surface oxidation is dominant only in acid (pH< 1.5) waters. The bacterial action accelerates the oxidation of sulphides, and large quanttties of sulphate may be introduced into solution.

Jan 1, 1976

By D. Chakravarty, B. Samanta, D. Ghosh

Autonomous robots are useful for 3D underground mine mapping to avoid human exposure to hazardous spaces. To prepare a precise mine map, a self-navigating robot must navigate an arduous path, avoiding obstacles and sensing the environment. A prototype laboratory-scale robot was built and evaluated through a mock-up in a test mine gallery. It was outfitted with a 2D laser scanner, a stereo camera for obstacle avoidance, and a high-precision, laser-based imaging and digitizing system for collecting 3D point cloud data. Various algorithms were used for scan matching to facilitate simultaneous localization of the robot for mapping.

Jan 1, 2014

By Denilson Coutinho, Euler Soares, Paulo de Tarso, Jordana Ferreira, John R. Goode, Andreas Sprecher, Alexandre Rocha

The Serra Verde Project is located in the northern part of Goiás state, Brazil, and comprises 49 mineral claims covering an area of 69,814 ha. The Serra Verde deposit is a rare earth element (REE) enriched weathered granite comparable to the weathered granite, or ionic-clay, deposits found in southeastern China. The Mineral Reserves of the Serra Verde Project total 388 Mt (Measured and Indicated) at an average grade of 1,484 ppm of REE oxide (REO). Several hundred agitated leach and column leach tests have confirmed recovery of about 40 to 55% of the REE, except for Ce, using simple desorption techniques. Present plans call for a heap leach operation followed by precipitation of impurities and precipitation of a pure REE carbonate suitable for refining and separation. The project plan includes initial production of 5,000 t/a of REO, with a high content of heavy and critical REO, rising to 10,000 t/a of REO. This production rate will be obtained by mining of the Mineral Reserves over a 22-year mine life at an initial rate of 6 Mt/a for the first four years with the mining rate thereafter increasing as required by grade and production targets.

Jan 1, 2014

By V. F. Hollister

Four conditions are commonly accepted as being needed for the development of native sulphur deposits in sedimentary rocks : (1) ample sulphate-bearing evaporite, normally anhydritic; (2) proximity to petroleum deposits; (3) a hydrodynamic system of communication between these two; (4) a stratigraphic or structural trap to prevent escape of the sulphur and sulphur -bearing reaction products. When any of these requisites are absent, apparently no significant residual bio-epigenetic sulphur deposit will form. These requirements are, however, satisfied in some areas, which include both the Triassic and Devonian evaporites of northeastern British Columbia.

Jan 1, 1977

By D. Mills, W. J. Brantina

"Mechanical and magnetic characteristics of ferromagnetic materials were investigated by a pulsed ultra-sonic technique. Two instruments, the Ultrasonic Attenuation Comparator (Sperry) and the standard type Reflectoscope (Sperry) were used for measurements of the attenuation of the ultrasonic pulse. The effects of elastic tensile and compressive stresses on the attenuation of annealed and cold worked material are described. In addition, the effects of plastic de-formation, relaxation and aging processes and different ultrasonic test frequencies are reported. The results for Armco iron, SAE 1020 steel, SAE 4340 steel and AISI 420 stainless steel are shown. Under the test conditions, the attenuation was found to be largely a sum of two components; a ""dislocation"" component associated with the losses accompanying the oscillations of dislocation line segments and a ""ferromagnetic"" component associated with the microeddy currents generated by magnetic domain wall oscillations. Either of these components might be dominant depending on the nature of the particular specimen and the test conditions. Finally, the possibilities of using ultrasonics in residual stress determinations, in fatigue studies and in the study of the ductile-brittle transition in ferrous materials, are briefly discussed."

Jan 1, 1960

By N. Plint, M. Potgieter

The Anglo Platinum Mogalakwena North concentrator was one of the first three hard rock mineral processing applications to utilise a HPGR circuit in preference to a SAG milling circuit. This was driven by the extreme competence of the ore that had given rise to throughput issues on the original South Plant. Despite more than adequate capacity and performance of the individual comminution units, the circuit has struggled to obtain full design capacity. A thorough review of the integrated performance of the circuit revealed a wide range of bottlenecks and underutilised parts of the circuit arising from design issues. Interestingly, the major opportunities lie in materials handling issues and mismatch of loads about the circuit. This paper presents the high-level outcomes and the associated opportunities, and is pertinent to all HPGR circuit designs.

Jan 1, 2012

By Werner W. Scholz

A corrosion-resistant lining is, quite often, selected on the merits of its corrosion resistance only. This paper demonstrates the effects of temperature, pressure, weather, design aspects and variances of physical properties within the scope of the generic designation of a corrosion-resistant material or materials. The base for the study is a rubber- and brick-lined steel vessel, with unchanged chemical conditions. Graphs and sketches illustrate the various effects of physical influences on the selected lining specifications.

Jan 1, 1979