Search Documents

By McGill Metals Processing Centre, S. Chang, L. Calzado, X. K. Cao, C. H. Hsin, M. Isac

"Due to the increasingly stringent cleanliness requirements for final steel products, there has been a growing interest in the possible use of micro-bubbles for the removal of inclusions with diameters smaller than ~50µm, present within the steel passing through a steelmaking tundish. However, several technological barriers have prevented the adoption of this technique in industry. These are related to a) the generation of micro-bubbles in liquid steel, b) the measurement of bubble size distributions, and c) the optimization of bubble injection conditions to create micro-bubbles. In the present study, a novel Aqueous Particle Sensor (APS) system was developed for the in-situ, on-line, detection of micro-bubbles in water, generated by a newly designed full-scale ladle shroud, located at McGill Metal Processing Centre (MMPC). Measurement results from the sensor were validated against bubble size data collected through a high speed camera and post-processed through the commercial software, Image J.Control variables and orthogonal experiments were designed to assess the dependence of average micro-bubble sizes and bubble size distributions on key experimental parameters. Those chosen were the air inlet flowrate, the distance of the gas injection port from the slide gate, and the number of injection ports used. The investigation demonstrated that the APS system can be successfully adapted to detect micro-bubbles up to ~800 micron diameters. Using this novel sensor, it was shown that multi-port injection using low air inlet flowrates, closer to the slide gate, were useful in forming small micro-bubbles within the flow through the ladle shroud. The results from the APS system were compared and validated against data resulting from an optical technique. INTRODUCTIONModern industry expects increasingly stringent cleanliness requirements for final cast products. Therefore, the numbers and sizes of inclusions need to be strictly controlled in steelmaking operations. Thus, the cleanliness of steel products depends on the amount, morphology and size distributions of nonmetallic inclusions in steel (Zhang L. & Thomas B., 2003). Since large, deep, tundishes provide longer nominal residence times for liquid steel passing through it to the exit SEN’s, this can provide the ideal place to separate inclusions, and bubbles can assist by removing help attach inclusions and float them to the top surface."

Jan 1, 2016

By C. H. Bertoni

"The Superior Province of the Canadian Shield is the largest gold producing area within Archean greenstone rocks in the world, with total production of over 140 million ounces of gold. One hundred and fifty-five mines have individually produced more than 8,000 ounces, although only a relatively limited number of deposits (33) produced more than one million ounces of gold. The output from these 33 deposits accounts, however, for 85% of total gold production. The majority of grades (68%) ranges between 0.10 and 0.30 ounce per ton, and there is no linear relationship between grade and tonnage.Development of new gold mines reflects the history of gold prices. However, the response to the latest increase in gold prices was not as marked. It is concluded that gold deposits are becoming increasingly more difficult to find and new exploration techniques are urgently required.IntroductionWith most of its production coming out of the Superior Province, the Canadian Shield is the largest producer of gold from Archean greenstone rock s in the world. In total gold production, the Superior Province is surpassed only by the paleo-placers of Witwatersrand and the placers of the USSR (Anhaeusser, 1976). There has been no attempt so far to compile the historical production of the Province as a whole in a single document. The aim of this work is to fill this gap, not only for the convenience of having a complete list of gold producers, but, more importantly, as a basis on which to study the tonnage and grade characteristics of these deposits."

Jan 1, 1983

By S. I. Vobnout, J. Wm. White, J. P. Olson

"Mine management now recognizes the value of computer-based truck-shovel dispatching in open pit mines. The key tangible benefits are substantial productivity increases with a given fleet of equipment or, alternately, significant reductions in equipment required to meet production quotas. In this paper, the authors review the literature, report on efficient, optimal algorithms for haul truck dispatching in real-time, and briefly discuss methods used by various mines to evaluate productivity improvements over manual methods. Actual results obtained at thirteen mining operations around the world are also presented.IntroductionModular Mining Systems manufactures, installs, and supports its computer-based DISPATCH system at mines worldwide. DISPATCH is a large scale, computer-based mine management system which controls the dispatching of all haul trucks in any open pit mine (Fig. 1). When increased production is important, DISPATCH gets the needed production increase with fewer new or recommissioned trucks. DISPATCH also helps operations meet its blending objectives while minimizing rehandle and maintaining production. Furthermore, DISPATCH includes a powerful, eventdriven simulation subsystem. With the simulator mine management can pose ""what if' situations and see the predicted effect on production"

Jan 1, 1993

By T. Lamb, T. Aston

"The Gays River Mine is located within a complex hydrological regime and underground mining environment. Early in the mine history, the operation was' affected by an inability to control mine water inflows. More recently, the reopened mine operation had been unable to maintain consistent drainage of groundwater to the mine workings and sustain low groundwater levels.In 1992, a series of investigations were completed, which in part Were funded under the Canada-Nova Scotia Mineral Development Agreement. The studies undertaken included: hydrochemical and drainhole well screen assessments, an air photo study of sinkhole features, numerical modelling studies and a major piezometer installation and overburden soil study. The results indicate that the water draining to the underground workings is comprised of two distinct components: precipitation over the drawdown cone catchment area and seepage from the nearby Gays River. In addition, a third ""balance"" component was' also found, which represents uncertainties in the areal extent of the drawdown cone and river seepage components.After outlining the history of the groundwater problems experienced at the Gays River Mine, this paper examines the various studies undertaken during 1991-1992 and concludes that control of groundwater levels in the mine area is achievable. A number of recommendations are also proposed for future study ."

Jan 1, 1993

By J. R. Morris

"A hoisting plant design should satisfy two basic requirements:1. to provide the necessary materials handling capacity, including ventilation where applicable, while meeting the requirements of good practice and, as a minimum, government regulation; and2. to optimize the economics of the project. Selection of hoisting equipment to meet the first objective is a complex but logical engineering process. The necessary calculations of payloads, accelerations, speeds, rope strength, hoist size, and power requirements are very readily carried out on computers or programmable calculators. A variety of hoist options can be quickly examined to assess the effects of changes in design parameters.Meeting the second requirement involves balancing the costs of various hoist arrangements and shaft designs, together with the time cost effects of differing shaft sinking rates and potential advances to be gained by concurrent level development. The proposed mine layout is significant here, as is the possibility of future shaft deepening and/or production increase. The availability of used equipment may be significant, both as regards first cost and delivery time. The factors are interactive, with their relative effects .varying from project to project. This paper sets out the primary factors to be considered."

Jan 1, 1990

By H. Stocker, C. E. Makepeace

"This paper presents the statistical analyses of several sets of data acquired in several programs of sampling of radon daughters in uranium mines. The measurements were taken over periods of days or weeks for given locations or location occupations within these mines. Because the sampling applies to specific intervals of time and specific locations, a method is suggested f or the eventual application of a monitoring program which would be suitable on an annual basis for these locations. The present data and analyses thereof are not justifiably applicable to a monitoring regimen on an annualbasis, without a number of additional assumptions.The aim of the present analyses of concentration measurements is the determination of the minimum number of measurements required to achieve an annual radon daughter exposure estimate, for individual workers, having an error no greater than 50% at the 95% confidence level. The criterion of accuracy is taken from a statement in the American National Standard, Radiation Protection in Uranium Mines (ANSI NI3.8-I973), and is currently used, in somewhat modified form, as a guide to uranium mining licensees in Canada. Uncertainties associated with occupancy time are ignored in the present analysis. IntroductionOne of the principal aims of any scheme of radiation protection is that of improving the accuracy of exposure estimation for workers. The example presented here is from the area of radon daughter exposure estimation for uranium miners. The conventional means of estimating workers' exposures is grab sampling of radon daughter concentrations combined with occupancy time weighting in the various work and travel locations. Uncertainties exist in each of these components, and in an environment of highly variable radon daughter concentrations (such as an active uranium mine) one is always uncertain as to the representativeness of the grab sample (compared to the average concentration) unless a sophisticated monitoring scheme has been implemented based on previous experience in such an environment.Improvements in the accuracy and precision of employee radon daughter exposure records depend, primarily, on three factors;"

Jan 1, 1980

By T. Alan O'Hara

"Annual mining revenue can be computed by formulae relating metal prices, smelting schedules, concentrate grade and recovery to known ore grade and an assessment of core samples. Operating costs at different daily tonnages are related to orebody shape, mining method, milling process and general plant services. Capital costs are related to sizing of mining equipment, mine development, plant-site topography, climate and accessibility, plant services and personnel housing. IntroductionA crude guide to the average 1978 cost of mine projects is shown in Figure 1, but the costs of many mine projects have differed widely from the graphed average costs of $800,000 T0.6 for underground mine/mill projects and $400,000 T 0.6 for low-grade open-pit mine/mill projects.High mine project costs and high operating costs are characteristic of open-pit mines with high stripping ratios, underground mines with thin orebodies, mills with complex metallurgy, and projects located in isolated regions with severe climate, mountainous topography, and lacking access to existing roads, towns and electric power. When none of these adverse conditions prevailed, the mine project cost was typically much less than the graphed average cost. Virtually all the conditions likely to cause high capital and operating costs are known from knowledge of the local topography, climate or accessibility, or can be assessed by tests on core samples, as soon as the orebody has been outlined by drilling .A more accurate estimate of over-all project capital cost and operating cost can be made from a summation of items of cost after judging the effect of specific local conditions on each item of capital and operating cost. This paper offers guides in judging the effect of local conditions on the sizing and 1978 cost of specific items of capital cost and operating cost and operating cost of mine projects. When the specific items of capital cost and operating cost are totaled and measured against expected net revenue and taxes over the life of the mine using the net-present-value or discount-cash-flow methods, the result should show whether the mine project development is clearly feasible, doubtfully feasible or clearly uneconomic. If the development of the mine project is clearly feasible, or probably feasible, a detailed feasibility study by experienced consulting engineers should be commissioned before any financial commitments are made; but if project development appears to be uneconomic, the time and cost of a detailed feasibility study is not warranted."

Jan 1, 1980

By J. B. Hinzer, J. D. Harvey

"Noranda's Lyon Lake property in the Sturgeon Lake area of Northwestern Ontario was staked by Mattagami Lake Mines Limited in May 1969 to cover airborne Input anomalies. Subsequent ground geophysical and diamond drilling programs resulted in the disco very of the Boundary Extension, Lake and Creek ore zones. As of December 31, 1978, ore reserves were estimated at 3,945,000 tons assaying 6.53 per cent Zn, 1.24 per cent Cu, 0.63 per cent Pb, 3.42 oz/ton Ag and 0.010 oz/ton Au.These deposits are hosted within the South Sturgeon Lake volcanic pile of Archean age, which consists of several cycles of basic intermediate and felsic volcanic materials overlain by a sedimentary iron formation and built upon a plutonic base (Franklin , ' 1975). The top 50 m of the second felsic cycle, according to mine terminolo gy, contains the mineralization within Quartzphenocryst- bearing felsic lapilli tuff and underlying thin discontinuous graphitic sediments and altered coarse pyroclastics. The basal andesitic member of the overlying cycle forms the hanging wall to the ore deposits.Although there is no alteration pipe below the deposits, the coarse footwall rocks are permeated by chlorite, garnet, carbonate, iron sulphide and magnetitie-bearing veins intensifying from west to east.Immediate host rocks are alkali depleted and MnO, FeO, Zn and Cu enriched compared to Goodwin's (1972) average Archean rhyolites. Bedded pyrite-pyrrhotite-chalcopyrite lenses with sphalerite-rich tops are underlain by weakly developed stringer mineralization.Traversing eastward from the Lake Zone to the Creek Zone and toward the Sturgeon Lake Mine deposit, more rapid facies changes, more pronounced chloritic and carbonate alteration, the presence ofgarnets, greater MnO, FeO, CaO and Ag abundances, and increasing Zn/Cu and MnO/FeO ratios are apparent."

Jan 1, 1981

By Kurt D. Mitchell

"This paper discusses general application for A C variable frequency drives in the mining industry. A review of induction motors characteristics, adjustable frequency controller fundamentals, and three commonly used controllers is presented. General application guidelines for the three different types of controllers; variable voltage input , current source input and pulse width modulated are then reviewed in detail, and an example of the economic benefit of this technology is discussed. IntroductionSoon after static DC variable speed drives were well established in industry, a need for static AC variable speed drives was seen. The first technical papers describing possible systems appeared in the mid-1960s, with commercially available units arriving in the early 1970s. Without exception, static AC drives are substantially more complex than their DC counterparts, but they have some very desirable properties. As compared to DC motors, AC motors are less costly, physically smaller, more reliable, require less maintenance , easily sealed, have good load regulation, are able to run at higher operating voltages, and have little danger of over-speed runaway . These properties are particularly desirable in explosion-proof, submersible or difficult accessibility applications.Variable speed AC drives are now a proven technology. available in packages from Sub-horsepower to hundreds of horsepower, from 115VAC to 4160 VAC. This paper covers the principles of operation of three common types of controllers, application criteria, motor consideration and finally an example of how an AC variable speed drive can pay for itself in terms of energy savings."

Jan 1, 1986

By Chas. L. Emery

"The laws of rock mechanics apply equally well to all rock structures, and open pits are not exceptions. The concepts and some arguments about the emphasis to be placed on various aspects of open-pit design are discussed in this article.RocksROCK can be described as a granular material consisting of grains and glue. The grains may be fragments of other rocks or polycrystalline aggregates. The glue may be ferruginous, calcareous, argillaceous, siliceous or other material connecting the grains. In a crystal intergrowth, the outer layers of the crystals in contact with each other may be considered to act as a glue. Water may be a glue in clay or a grain in a crystal structure. Air and other fluids or gases are grains if they occupy spaces in a granular mass. Such grains are functional either chemically or mechanically or both."

Jan 1, 1966

By M. S. Badollet

Introduction Very little fundamental research has been done on asbestos fibre to cake maximum advantage of its properties and to determine in what commercial products it can best be utilized. For the research chemist who is associated with asbestos development work, a thorough study of mineralogical information on asbestos deposits would furnish reliable information on the rock formations and the mineral impurities closely associated with the asbestos. Furthermore, ?he must have an intimate knowledge of the uses of the fibre in various products so that he can visualize the importance of the fibre and the role it plays in industry. Some of the properties of asbestos fibres such as strength, composition, length, harshness or softness, and mineral associates are of considerable importance to the manufacturer because they are responsible for many production difficulties. Fibre Strength It has been known for some time chat asbestos filaments have considerable tensile strength. These strengths have been referred to merely as 'weak' to 'very strong'. Not until recently have numerical values been applied to the strengths of asbestos fibres. But today we can take a thin fibre filament and mount it between two holders and apply a gradually increasing load or pull until the fibre breaks. By measuring the cross sectional area of the filament and the amount of load applied, we can calculate the tensile strength of the fibre in terms of pounds per square inch. This type of test is slow and rather difficult, but the fundamental data obtained furnish important basic information that can be applied to mechanical processing equipment and to certain asbestos products.

Jan 1, 1948

By D. F. Scott

"DEFINITION OF THE REGION AND ITS BOUNDARIESTHE REGION of Western Canada covered by this re-port lies between the Precambrian rocks of the Canadian Shield and the structurally deformed rocks of the eastern Cordillera, extending northward from the international border to the 60th parallel. It is some 487,000 square miles in area, with a total sedimentary fill of about 535,000 cubic miles0>. It includes parts of the prairie provinces of Manitoba, Saskatchewan and Alberta and the northeast corner of British Columbia and forms part of the geological region known as the Interior Platform, commonly referred to as the Western Canada Sedimentary Basin. The bedrock comprises carbonates and evaporites of Paleozoic age that lie on Precambrian crystalline rocks and are over-lain by a relatively thick blanket of Mesozoic and Tertiary elastic rocks. The nearly flat-lying bedrock, covered by a thick mantle of glacial drift, forms the Interior Plains physiographic province."

Jan 1, 1970

By J. E. Dutrizac

A pyritic Zn-Pb-Cu ore waspercolation leached with acidified ferric sulphate solutions; zinc and copper were leached, lead was oxidized, but not dissolved, and pyrtte was essentially unattacked. High zinc extractions were achieved after a few months leaching, and substantial zinc solution concentrations could be produced by recycle of the oxidized solution. The leaching rate was generally controlled by the transport of the ferric sulphate oxidant. Zinc extractions increased with increasingferric ion concentration or flow rate, but were essentially independent of the concentrations of sulphuric acid, ferrous sulphate, cupric sulphate or chloride ion. The leaching rates were insensitive to the height of the ore column once a minimum height had been exceeded (0.8-1.0 m). Elemental sulphur was the principal sulphidic reaction product, but variations in the ratio of sulphur to sulphate produced anomalous temperature effects.

Jan 1, 1979

By Jean-Yve Tremblay, Michel Prud'homme

"Industrial minerals include a group of more than fifty minerals which are marketed into almost all the sectors of industry; they are the backbone of many manufacturing industries. Table I shows major end-uses for industrial minerals in manufacturing sectors. At Energy, Mines and Resources, industrial minerals are divided in three major categories: (I) agro chemicals and chemicals, (2) construction mineral s, and (3) ceramics and specialty minerals. A listing of the major groups of minerals is shown in Table 2. Agro-chemicals and chemicals are sold on the basis of their chemical content and purity. Construction minerals or structural minerals are distinguished by their performance as low cost and bulky commodities. Ceramics and specialty minerals are performance-specific and are sold for their property on imparting functions on end-products. Industrial minerals have unique characteristics that are useful in many stages of processing; from crushed size to micronized fillers a single mineral ca n serve a broad range of industries because of its intrinsic properties."

Jan 1, 1988

By James D. Bliss, David M. Sutphin

"On the basis of differences derived from genetic, descriptive, and grade-tonnage data, graphite deposits are classified here into three deposit types: disseminated flake, amorphous (microcrystalline), or graphite veins. Descriptive models have been constructed for each of these deposit types, and grade-tonnage models are constructed for disseminated flake and amorphous deposit types. Grade and tonnage data are used also to construct grade-tonnage models that assist in predicting the size and grade of undiscovered graphite deposits. The median tonnage and carbon grade of disseminated flake deposits are 240 000 tonnes and 9% carbon and for amorphous deposits, 130 000 tonnes and 40% carbon. The differences in grade between disseminated flake and amorphous deposit types are statistically significant, whereas the differences in amount of contained carbon are not .IntroductionIndustrial minerals, including mineral construction materials such as sand, gravel, and crushed stone, have historically exceeded metals in global production value. Today, industrial minerals are being used in new and sophisticated ways in response to the late 1980s emerging information- and service-based economies' requirements for less metal and more industrial minerals . Natural graphite is an example of one such mine ral that has been known since ancient times, and is now finding new applications. Graphite was first used as an industrial mineral in Bavaria in 1400 A.D. where it was an important component of crucibles. Traditionally, natural graphite has been used in heavy industries. New applications, such as development of carbon-magnesite bricks a decade ago and the current advancement of alumina/graphite refractories, are increasing its graphite use. Other new uses for natural graphite, such as the use of graphite powder as a thermal blanket for the continuous casting o f steel (Northern Miner, 1987) and the addition of expanded graphite to polyurethane foam where it acts as a flame retardant (Industrial Minerals, 1987), are increasing the demand for this mineral. To meet future demand for graphite and other industrial minerals, knowledge of the characteristics of the deposit types in which they are found is important. A further look at the deposit types for graphite and at construction of descriptive and grade-tonnage models is warranted .The graphite industry recognizes three basic types of graphite , distinguished primarily on the basis of grain size: crystalline flake, lump and chip, and amorphous. These naturally occurring forms of graphite are products of metamorphism and are found in schists of various types, gneisses, and marbles. Temperatures of at [east 400°C are thought to be required for graphite formation (Landis, 1971). Synthetic graphite, also known as artificial or manufactured graphite, is a man-made carbon product and offers higher purity and lower crystallinity than natural graphite. Several authors have written about graphite's unique physical and chemical properties and the uses for individual types of graphite (Krauss et 01., 1988; Graffin, 1983; and Harben and Bate s, 1984)."

Jan 1, 1990

By C. Desmeules

"Carbon addition in the oxide pelletizing process is a big concern at the Sidbec-Normines pelletizing plant since 1976.Laboratory pot-grate testing carried out before the initial start-up of the Port-Cartier plant indicated that the nominal pelletizing grate capacity could be increased by fifteen per cent with a suitable carbon addition. Also an improved induration cycle offered the possibility of a significant energy reduction within the process with no adverse effect on pellet quality. A one-month plant scale program duplicated the lab test results and confirmed the anticipated cost saving by using these techniques. Since March 1980, Sidbec-Normines used coke addition as a current operation.This paper reviews briefly earlier laboratory and in-plant test work carried out to investigate the effects of adding carbon materials to the Fire Lake hematite concentrate, and presents operation techniques and plant results of carbon addition in the Port -Cattier pellet plant.IntroductionThe Sidbec-Normines pelletizing plant at Port-Cartier, Quebec, is designed to produce six million ton s per year of oxide pellet s. It is a Dravo-built two-line plant; one line to produce three million s tons per year of blast furnace grade pellets averaging 5.5 per cent silica, and another line of three million ton s to produce direct reduction grade pellets of about 2.0 percent silica.The laboratory pot-grate test program was conducted in 1977 at the British Steel Corporation Research Laboratories in England, with the assistance of J .E. Appleby, consultant to British Steel Corporation (overseas services) Limited.The purpose of that test program was to determine the optimum energy saving cycle and to study the physical and metallurgical effects on blast furnace and direct reduction pellets."

Jan 1, 1983

By M. Leroux, J. A. Finch

"Sizing below 38 µm (400 mesh) is an increasing requirement in mill testing laboratories. The Cyclosizer is gaining wide acceptance in this role. A recent alternative is to use electro-formed sieves (micro-sieves), which are available with openings down to 5 µm. The advantage of micro-sieving is a cut size which is independent of mineral density, easier retention of the fi nest fraction and reduced purchase cost. A simple method of microsieving using an ultrasonic bath, which performs readily to 10 µm, is described.A systematic study of Cyclosizing and micro-sieving is reported for three samples; silica, copper oxide and a lead concentrate. Micro-sieving gave comparable results. Comparison with a standard sizing method, the Sedigraph 5000D, revealed misplaced material in each fraction by both methods. The range for micro-sieving was from 20% to 60% depending on the sieve and material; for the Cyclosizer it was a consistent 40-50% for all cones and all materials. The Cyclosizer can be sensitive to feed mass and particle size for dense materials. It is recommended that for minerals of specific gravity greater than 5, no more than 35 g of -38 µm be used.The disadvantage of micro-sieving is that it requires continuous operator attention and sieving time depends on sample mass. To fractionate 35 g-as used on the Cyclosizer and considered at reasonable mass for mill testing purposes-through 25-, 15- and 10-µm sieves requires about 80 minutes.IntroductionParticle size has a pronounced influence on mineral separation processes. Consequently, the measurement of particle size plays an important part in mill testing. By far the most common method is by screening. This, however, is usually limited to 38 µm (400 mesh) or occasionally 25 µm (500 mesh). Increasingly, mineral products are becoming finer than this limit and consequently finer sizing methods are required."

Jan 1, 1982

The 2-4D window shown above is the base startup window which allows you to begin a new project. ??Setting up the project is the first step ??The next step is to setup the properties to be used in this project

Feb 1, 2008

By Kri Inwood

"IntroductionIn 1879, when the Dominion government initiated its controversial program of industrial promotion, iron smelting in Canada was limited to one company producing coke iron on the mainland of Nov a Scotia and three small charcoal blast furnaces in Quebec. There was no steel production. By the eve of the first great war, iron and steel were being produced in very large quantities, the companies active in 1879 had disappeared and new centres of integrated iron and rolled steel production at Hamilton, Sydney and Sault Ste. Marie had come to resemble the industry as we know it today.The most dramatic change was that at Sydney, Nova Scotia, where in the early 1900s, two steelmaking companies established works. The Sydney developments have been explained as the result of resource discovery and technical change. W.J. Donald, in his authoritative account of the Canadian iron and steel industry, observes:""The most rapid growth of the Canadian iron and steel industry has occured since 1897... The remarkable growth has been caused largely by the new conditions of the industry. The discovery and use of Newfoundland ores, together with the availability of Cape Breton coal, has made the Nova Scotia industry not only possible but profitable ... It is a safe conclusion that the Canadian industry would not have been an important one, had it not been for the discovery of the Michipicoten and especially the Wabana (Newfoundland) ores""Donald also argues that metallurgical progress had been necessary to render the ores valuable,""Newfoundland ores ... contain a considerable amount of phosphorus, and were made available for steel-making by recent inventions.""The purpose of this paper is to re-examine Donald's story. It will be argued that the origin of steel -making at Sydney is somewhat more complicated than Donald has indicated. The difficulty with Newfoundland ore extended beyond its phosphorus content and a resolution required more than the basic open hearth furnace identified by Donald. Moreover metallurgical change was only one of several developments necessary to induce industrial investment at Sydney. Surprisingly, however, the discovery of iron ore in the late nineteenth century does not appear to be part of the explanation."

Jan 1, 1983

By P. K. Kaiser, S. Maloney, S. Yazici

"This paper focusses on the strength or capacity of cable bolts and introduces a new perspective for cable bolt design by demonstrating that mining-induced stress changes may affect cables in a detrimental manner. The concept underlying a novel cable bolt pull-out resistanceor bond capacity model is described and its practical significance is demonstrated by application to a simple two dimensional scenario of a fall-of-ground.A number of practical implications emerging from the application of this model are discussed to provide guidance to ground control personnel jar improving cable bolt support systems in mining applications. These include cable layout optimization, use of cable pre-reinforcements, assessment of embedment length requirements, need for plated cables (or straps), use of bird-caged cables (or buttons), and grout quality issues.IntroductionDuring the last decade, cable bolting has become a standard support technique in mining for handling wide spans, reinforcing are passes, preventing or reducing dilution of ore in marginally stable stopes, and for many other rock support need s.In its infancy, many deficiencies in cable bolt supports resulted from improper installation techniques and, in particular, grout quality control problems and the use of empty breather tubes (Goris, 1990). The development of special grout pumps and fail proof placement procedures (Oliver, 1992; Bourchier and O'Flaherty, 1992) have eliminated many of these early problems. Nevertheless, there are still situations where cables seem to lose their capacity during mining, and in these cases the cables do not provide the expected and needed ground support. In some instances, cables perform extremely well, whereas in others the same support layout and quality of support installation seem to be insufficient, allowing falls-of-ground or progressive cavings to occur."

Jan 1, 1992