Search Documents

By L. Haavanlammi

Iron is a significant component of all copper concentrates leached in the HydroCopperTM process. The metals in the concentrate are leached in a chloride solution by oxidation with cupric ions. Copper enters into the solution as a cuprous chloro¬complex. Iron dissolves at the same time in the ferrous form, but it is immediately oxidized to the ferric state. Oxidation is effected by sparging air or oxygen into the leaching reactors. Because the pH is 1 - 2.5, ferric ion precipitates as akaganeite (T<90°C) or hematite (T> 90°C). Arsenic, antimony and the main part of the bismuth co-precipitate with iron and report to the leach residue. Cupric leaching is faster than iron oxidation; thus, leaching of low-iron concentrates (secondary copper minerals) is quicker than leaching high iron concentrates (chalcopyrite). Pyrite does not dissolve during copper leaching, but is oxidized slowly at higher redox-potentials after the copper has been leached.

Jan 1, 2006

By A. Mosqueda Martinez, L. C. Trytten, R. P. Kofluk, J. J. Budac

The Corefco ammonia leach nickel refinery treats Ni-Co mixed sulphides from the high-pressure acid leaching of Moa Bay nickel laterite. Due to the low iron content of the feed, the ammonia leach process generates a leach residue with ~10% Ni+Co. Since commissioning a leach residue pressure filtration circuit in 2002, this residue has been stockpiled, dried, and sold commercially. For several years, the residue was sold to nickel smelters overseas. In 2014, re-processing of the residue in the high-pressure acid leach was tested. Lab test work was completed showing excellent extraction of the contained nickel and cobalt, and additional beneficial effects in the high-pressure acid leach circuit. A plant test in Moa confirmed the results, and preparation for shipment of the valuable leach residue for re-processing has begun. This paper outlines the test work and results, and some commercial considerations.

Jan 1, 2015

By R. H. Schonewille

One of the many challenges in developing new metallurgical processes is choosing the best option for validating process design parameters and establishing the process operating window. Historically this has been achieved by constructing pilot or demonstration plants of considerable size and complexity, to enable integrated operation of all key process units for a significant duration. While this would appear to be the best option for minimizing technical risk, it is often impractical from a perspective of cost, schedule, resources or bulk sample acquisition. Such an undertaking can even provide a false sense of security, as the optics of running a complete scaled-down version of a commercial plant suggest a high level of process understanding, regardless of the challenges encountered during operation. Xstrata Nickel has undertaken numerous process development and improvement projects over the past 15 years to support green field project development and continuous improvement in existing operations. The approaches used have included; computer simulation, cold flow modeling, construction of pilot test units in third party facilities, commercial plant referencing and the more conventional construction of integrated test plants. Regardless of the strategy employed, the keys to success have included; managing stakeholder expectations, involving the commercial plant design engineers in the planning stage, anticipating subsequent data and sample requirements and most importantly, constructing and operating complex demonstration plants only as a last resort. This paper provides examples of various process development approaches used by Xstrata Nickel and discusses the rationale specific to each project.

Jan 1, 2011

By G. G. Li

"A dynamic ventilation-modeling package, VREX, was used to simulate the mine activities through tracking the equipment movements in underground workings and determine the airflow demand for a new production scenario in a ventilation-on-demand (VOD) system. It incorporates the mine development data from a discrete event simulation and balances the ventilation network using the CANVENT ventilation solver. A case study was performed to demonstrate the capabilities of the software, evaluate the performance of the network and determine the potential energy savings for implementing VOD in a deep mine operation.INTRODUCTIONThe ventilation cost of an underground mine can be significant—up to 50% of the mine’s energy consumption could be used to run fans and provide heat/refrigeration to meet the specified production environment for workers and equipment. The VOD system has proven to be more efficient in operating the fans and supplying the amount of air corresponding to the mine activities taking place in underground workings (Hardcastle, Kocsis, & O’Connor, 2006). In order to properly solve and evaluate the VOD system, a dynamic ventilation modeling software VREX—the ventilation rules engine has been developed to simulate the mine activities and determine the airflow demand for each production scenario within an operation period (Dasys & Cameron, 2011).VREX is a decision support tool, backed by the CANVENT mine ventilation solver (Li, Kocsis, & Hardcastle, 2009), for determining the outcomes of network configuration changes over time. The software incorporates the mine development data with ventilation modeling through the discrete event simulation (DES) performed by SimMineTM. As it simulates the air requirements for different vehicles and activities, VREX can evaluate both the performance of the ventilation system and the potential economic benefits of making operational or technological changes (Pritchard, 2010). For example, the model can be used to assess the economic and environmental impacts arising from modifying regulations to support the use of electric or lower emission vehicles. The combination of DES and ventilation modeling provides a new technology to generate the production scenarios according to mine schedules and activities and to determine the potential benefits for various levels of ventilation control, such as time interval and work shift change."

Jan 1, 2019

By John H. Nicholls

In this paper, Imperial Oil Limited reports briefly on the drilling by contract rigs of twenty-nine slim holes in the Virden, Smiley, and Souris Valley areas. The investigations showed that slim-hole penetration rates, as a result of careful control of drilling variables, can approach those achieved with 7 7/8-inch bits. It is concluded that slim-hole drilling is acceptable for development or exploratory work. Imperial also reports on the completion techniques and equipment that have been developed on twenty-seven tubingless 2 1/2-inch casing completions. Indications are that the method is economically desirable where excessive gas or water production is not anticipated.

Jan 1, 1958

By K. G. Wheeland, K. G. Byberg

The occurrence of a secondary, dust-fuelled explosion following blasting of sulphide ores has been reported in mines in many countries, including canada, the USA, Australia and South Africa. However there has been little effort to document the events and develop effective control technology. Following a detailed investigation of an incident at the Geco Di vision of Noranda Minerals Inc. , the company held a conference of interested parties in October 1986 to review the state-of-the-art and to agree on action. '!his paper outlines the causes and effects of such explosions, the key conference points and conclusions, and subsequent information-exchange and teclmology-developrnent activities.

May 11, 1988

By Yugo Mitani, Tatsuya Kato, Chiharu Tokoro, Abdullah Al Mamun

Acid mine drainage (AMD), which is a major source of mining pollution, often contains ferric and/or ferrous ions together with several toxic elements. The ferric and ferrous ions in AMD precipitate in several mineralogical forms after neutralization, and the ferric/ferrous precipitates become the main component of the sludge generated after AMD treatment. The precipitates are also good absorbents for several toxic elements. To avoid generation of voluminous sludges and the re-dissolution of toxic elements from the sludge, it is very important to generate well-draining and efficiently adsorbing sludges by controlling the mineralogical form of the ferric/ferrous precipitates. Green rust, which is ferric and ferrous hydroxide, is a double layer hydroxide which is able to sorb several toxic elements. The green rust transforms to goethite or lepidocrocite by rapid oxidation, whereas it transforms to magnetite at ambient temperature by slow oxidation. The magnetite is also good absorbent especially for toxic cations and it makes a compact sludge due to its magnetic properties. We investigated the magnetite generation process at ambient temperature in detail. The magnetite generation process can be divided into three steps; (i) oxidation of Fe(II), (ii) Fe(II) surface complexation to Fe(III) hydroxide, and (iii) crystallization of magnetite. More magnetite can form when the oxidation rate is slower than the crystallization rate, and optimum conditions for its formation are at pH 9.5 with mild agitation. Ferrihydrite is the most common precipitate and it is able to sorb many different toxic elements. However, it drains badly and its solid/liquid separation properties are poor. We investigated the removal mechanism of several toxic elements by co-precipitation with ferrihydrite. We confirmed that the removal mechanism by co-precipitation partly involved surface precipitation when the initial ratio of toxic elements to ferric ion was high, although the main mechanism was always surface complexation. When surface precipitation occurred, highly efficient toxic element removal with ferrihydrite could be achieved.

Jan 1, 2016

By D. Hu, L. Matzar, J. Hampton, M. Gutierrez

Nanodarcy permeability is common in many oil- and gas-bearing formations requiring unconventional stimulation technologies, such as hydraulic fracturing (HF), which can connect the isolated hydrocarbon-rich pores with a wellbore through induced fracture networks. Even though a dense induced fracture network is capable of accessing economic amounts of hydrocarbons, much of the rock between and very close to the fracture network is still un-accessed and contains extremely low permeability. Inducing fracture networks into brittle rock can create large amounts of micro failures in surrounding regions that are not connected to the wellbore, as can be seen in Fig. 1(a) from the very wide acoustic emissions (AEs) cloud associated with a narrow fracture generation. It is possible in certain types of rock to increase the effective matrix permeability in localized regions based on the damage associated with the surrounding hydraulic fractures and subsequent high stress concentrations along localized pre-existing potential failure zones. To study this problem, laboratory HF tests were performed at true-triaxial stress state in brittle crystalline rock while monitoring AEs. The AE associated with HF was analyzed for source parameters using the moment tensor inversion method called Simplified Green’s Functions for Moment Tensor Analysis (SiGMA). Using the moment tensor for each individual AE event, the mode of failure was determined. Crack slip directions and crack face normal directions were also found, along with the relative volume of individual micro failures as well as a damage parameter. The associated source parameters were used to classify differing regions of damage in the sample induced from HF and correlate these regions of differing damage to the effective drainage region. Shown in Fig. 1(b) is a near-wellbore (NWB) region that contained three times larger average relative volumetric deformation of individual tensile AE events than the average tensile AE event volume from the entire sample. Because of the large difference in micro fracture volumetric deformation for the NWB region compared to the entire sample, predictions of HF induced damage must be included in reservoir drainage predictions.

Jan 1, 2015

"In developing a backfill system handling tailings feed to and from the storage silo, it is necessary to establish a slurry laboratory to develop the technology and silo design criteria. This paper presents the principles involved in such development and the importance of testing principles for optimizing the slurry system. Evaluation procedure based on experiments is applicable to a wide range of materials and allows silo design by scaling up the data gained from model tests. Silo simulation has been successful to design and operation, so becomes an effective approach to backfill applications. IntroductionThe silo is a device comprising specialized equipment and operating with related procedures for storing and handling the mill rejects as backfill slurry. It provides a steady supply of the solids slurry, prepared at desired pulp density under the continuous feed conditions. Because the silo system is designed to accomplish specific objectives when dealing with a particular mill tailings slurry, it is necessary to characterize certain slurry properties, behaviour of the solids slurry and understand the silo performance to establish design criteria. Bench-scale, pilot-scale and dewafull- scale experiments were employed in developing the load-storage-discharge system, and routine procedures are now available for pre-design testing. Silo model experiments and full-scale tests were conducted to define the design parameters and evaluate the silo performance. A silo can be designed by scaling up the silo model geometry and data obtained during tests.Since the early 1960s, silo backfill systems have been widely established. The shape and size of the silo and the operation procedure, as practised, all appear to be relevant to successful operation. Understanding the basic material properties and behaviour of solids slurry retained in the silo will help perfect the silo design, operation procedure and, consequently, improve the silo performance."

Jan 1, 1997

By J. Visman

"SummaryThis paper is presented as part of a programme to show the steps taken by industry and others interested in supplying a solid fuel of constant quality to 'satisfy a consuming market. The paper deals with the general principles underlying quality control in coal preparation plants, namely, constant quality and close adherance to acceptance limits. It also describes how control of ash content is ""generally hampered by the problem of coal sampling .and the long duration of the ash analysis and how these difficulties may be overcome.Quality control can be effected in several ways. Thorough blending wll reduce variations appreciably, except those of long trend. The latter can be detected by automatic sampling and quick ash analysis. At present, under favourable conditions, a system of half-hourly ash determinations with an accuracy of 0.5 to 1.0 per cent can be realized, to the effect that trends with a 'wave length' of more than two hours cu be eliminated within the limits of accuracy of the ash figures. The general solution of the problem is a combination of blending, accurate sampling, quick ash determination, and statistical analysis of the pattern of ash distribution.The use of statistical methods of analysis, such as the t test and F test, is •discussed at some length in order to emphasize the importance of the correct evaluation of observational data if there is to be confidence in the validity of test results.General ConsiderationsCOAL, as a fuel, is too cheap for a long haul across the country. The limiting distance depends on the price of the local competitive fuels, and, as the price depends to a great extent on quality, so does quality, to the same extent, command the market."

Jan 1, 1952

By Nathaniel S. Scott

Caland Ore Company Limited, a subsidiary of Inland Steel Company of Chicago, Illinois, leased an iron ore deposit from Steep Rock Iron Mines Limited on January 1, 1953.. This deposit lay underneath a lake and was covered with 161,000,000 cubic yards of Jake bottom material, mainly silt. Removal of this material was done on a contract dredging basis. This contract was divided into a plant phase and an operating phase. The plant phase consisted of supplying two cutter-type suction dredges, each with two booster pumps in the discharge lines. All six pumps were centrifugal, had 36" discharges and were powered by 10,000 horsepower electric motors. Peak demand was 59,157 kilowatts. One hundred and forty miles of steel tower line were built to bring power to the site. The balance of the plant consisted of tugs, 12 miles of discharge line, varying from 36" diameter to 42" diameter and attendant land-based equipment. A number of interesting dams were constructed

Jan 1, 1961

By K. B. Han, S. Winkler, M. J. Benoit, M. J. Worswick

"Automotive heat exchangers are fabricated by forming multi-layered aluminum (Al) alloy brazing sheets into the desired geometry and subsequently passing the assembly through a furnace for brazing. As manufacturers seek to use thinner gauge and higher strength sheet to reduce vehicle weight, forming of the Al alloy sheets has become a challenge. Warm forming has previously proven to allay these forming concerns, but no consideration was given to the effect of increasing the forming temperature on brazing. Recently, it was shown that annealed sheet was more susceptible to the detrimental phenomenon of liquid film migration (LFM) during brazing if formed above 150°C, while work hardened sheets showed no increased susceptibility to LFM with increasing forming temperature, up to 250°C. In the current study, the brazing performance of simulated battery cooling plates was investigated. The plates were fabricated both from fully annealed and work hardened sheets. Brazing was assessed by microstructural evolution during a brazing cycle. The post-brazed microstructure varied with strain and forming temperature in plates made from annealed sheets, while no variation in microstructure with location or forming temperature was observed in plates formed from work hardened sheets.INTRODUCTION Since the 1970’s, one common method of fabricating automotive heat exchangers has been by forming multi-layered aluminum (Al) alloy sheets, and subsequently brazing the formed components together in a controlled atmosphere furnace. The Al alloy sheets used are comprised of at least two Al alloys roll bonded together, but can consist of additional layers, depending on the application; at minimum, the sheets are comprised of a core and clad layer. The core layer, often an AA3xxx alloy, remains solid throughout processing and provides strength to the assembly. The clad layer is always one of the AA4xxx series alloys which, due to their high silicon (Si) content, have a melting temperature range well below that of the core alloy. When the sheet is passed through the brazing furnace, the clad alloy melts to provide the brazed joint filler metal throughout the assembly, while the core alloy remains solid. In order to achieve cost and weight savings, heat exchanger fabricators have used Al alloy sheets with reduced thickness. However, deformation and brazing of these increasingly thin components remains a concern (Zhao & Woods, 2013). Furthermore, springback has been observed after forming sheets of higher initial strength (i.e. work hardened conditions), leading to flatness issues of formed components. Consequently, the ability to form high quality brazed joints is difficult in components formed from higher strength brazing sheets."

Jan 1, 2018

By Thomas G. Madgwick

Introduction Development of oil and gas is still centred in the Province of Alberta, much as it was when C. C. Ross read a paper on this subject three years ago at the Annual General Meeting in Montreal; but so far as gas is concerned, its early production in Saskatchewan seems now assured. The three years that have elapsed since Mr. Ross&apos; paper have witnessed a growth in the world&apos;s production of oil that has created a potential supply out of all proportion to the demand for petroleum products, and one that has resisted the most energetic efforts of the industry entirely to control. The natural result has been very much to retard the active prospecting of new structures in the Prairie Provinces with any immediate view to oil production, although the same factor has not hindered the search for gas to the same extent. One consequence has been to divert the attention of organized oil operators from wildcat drilling to more detailed geological investigation than had hitherto been customary, sometimes accompanied by test drilling with a view to the elucidation of geological structure rather than to the immediate development of production which at the present is not needed. Nevertheless, in spite of the growth of this phase of oil prospecting - which the writer would be the last not to welcome as a very real blessing and of far greater value than indiscriminate wildcat drilling in either the complex structures of the foothills or the simpler but largely concealed formations of the plains- it is most satisfactory to have to record that in these three years the growth of production both of naphtha and the heavier crude-oil has kept pace with the by no means inconsiderable growth in the production and utilization of natural gas.

Jan 1, 1929

By L. E. Djingheuzian

ANON-CATARACTING (N-C) ball mill is so operated that the balls are not thrown in-ward at the top of their paths. The result is to maintain, in the mill, a quiescent pool in which classification will occur at a limiting size corresponding to the pulp density. N-C operation is produced by effecting proper relationship among mill speed, ball diameter, volume of ball load, and pulp density. Such operation is typified by the primary ball-mill operation of the Tennessee Copper Company, Copper-hill, Tenn., and the Cleveland Cliff Iron Company, near Ishpeming, Mich.

Jan 1, 1958

By K. Trapani

"The study undertaken aims to investigate an ice stope heating and cooling system for its potential to be implemented in sub-arctic mines, as a low carbon alternative to conventional natural gas and refrigeration chiller systems. Its performance was simulated for a years’ worth of data, taking into consideration hourly temperature data. Results showed that to supply the required heating and cooling loads, the ice stope system had to supplement its heating with natural heating. The techno-economic performance of this system was compared to that of a conventional heating and cooling system in a mine, with the ice stope thermal storage system hawing the lowest annuitized cost and significantly lower carbon emissions.INTRODUCTIONConventional heating and cooling, in a mine is implemented using natural gas heaters and chiller refrigeration systems respectively. This results in a significant portion of energy consumption in underground mines attributable to ventilation (De Souza, 2015), including the conditioning of the air to ensure that temperatures do not exceed work comfort standards (ACGIH, 2011). Especially at depth where heat could become a significant issue. An ice stope thermal storage, using ice as the storage medium is being proposed as an alternative to provide the heating and cooling—with the ice creation resulting in heating and the ice melting providing the cooling required. A techno-economic investigation of the two systems is undertaken to identify the capital and operating costs for the two systems, and to assess the ice stope’s potential to be considered a low cost and carbon solution for heating and cooling of mines in sub-arctic climates.NATURAL STORAGE SYSTEM – CONCEPT DEVELOPMENTThe concept for the natural storage system is developed from the ice stope at Frood-Stobie Mine, ON, Canada (Stachulak, 1991). The ice stope was developed for mine air heating, with the heating occurring by spraying warm return service water onto the cold intake air—resulting in the air temperature increasing and ice being created in the stope. In summer this ice was melted by passing warm air on top of it, resulting in slight cooling of the air but no significant temperature difference which could allow effective cooling. A schematic of the Frood-Stobie Mine ice stope is provided in Figure 1."

Jan 1, 2019

By P. Schmidt, M. Hopf

Water-cooled parts of submerged arc furnaces are potentially dangerous, especially if molten matte or slag contacts the water. Explosion hazards and metal run-outs generate high costs for production loss and repairs - not mentioning the possible loss of human life. This paper reports about practical results of wear measurement on intensive water-cooled tap-holes and spray-cooled side walls. On the one hand an embedding technology has been developed, that is used e.g. in water-cooled copper tap blocks or copper side wall coolers. Second the application of the sensor installation on the inner side of a water-cooled steel shell will be discussed. The fibre-optic sensor is fed through a specially arranged piping system and measures numerous temperatures over its entire length. By using the thermal conductivity of the installed refractory materials the lining thickness is calculated. The practical installation of the sensors will be discussed and the results of the wear measurement will be compared to the theoretical FEM calculations. The highly sensitive and accurate temperature measurement, as well as the recalculation of the impact of differences in the cooling water temperature, allows the exact determination of the remaining lining thickness. The discussed technologies offer efficient and safe monitoring of tap-holes, side walls and other endangered parts of pyro-metallurgical smelters.

Jan 1, 2015

By D. N. Thurston

Luscar Stereo commenced construction of the mine at Coal Valley, Alberta, in August, 1976. It is designed to produce approximately 2.5 million clean short tons of steam coal annually - 2.0 million tons per year being committed to Ontario Hydro and 0.5 million tons per year being committed to Neptune Terminals for sale on the export market. The project involves constructing a heavy-media coal preparation plant, erecting a 42-cubic-yard dragline, constructing a shop/office complex, and developing three surface mining zones and associated facilities. As there were no existing facilities in the Coal Valley area, it was necessary to establish access roads, an airstrip, temporary utilities, fuel supplies, a construction camp, rail upgrading and communication services.

Jan 1, 1978

By G. Velarde

Agglomeration has as main objective to form a uniform and highly permeable heap for leaching. An inaccurate dosage of moisture during agglomeration leads directly to poor agglomerate quality and segregation of particle sizes during stacking. This causes a heterogeneous distribution of the leach solution inside the heap which invisibly and practically permanently affects the recovery. Unfortunately, only when this becomes serious and the mineral contains an excess amount of fine particles and/or clays then the poor permeability of the pile becomes obvious. This paper is based on the experience of Minera Cerro Verde in the development and application of a quantitative method to control moisture during agglomeration. As the amount of fine particles/clays varies, the quantity of moisture has to be altered in real time. The measurement of agglomerate electrical conductivity is used for it. This concept is based on the sharp change seen in conductivity when the mineral passes its absorption limit. A liquid conductive film then begins to form over the surface of the particles, which leads to the formation of agglomerates through liquid bridges, which are also electrical bridges. Moisture is adjusted to reproduce a value of conductivity established previously and is the guiding parameter. Moreover, moisture amount added to reach this conductivity parameter provides information about the fines/clays relative content for best leaching management.

Jan 1, 2004

By W. L. Nelson

The orebodies at Copper Mounta1n lie along and within a few hundred feet of the contact of an intrusive stock of gabbro with a series of bedded volcanic rocks of the Nicola formation. These. orebodies are all entirely within the volcanic series but in many cases the centre line of the orebody at depth is directly under the gabbro contact at the surface, due to a slight overhang of the gabbro. The gabbro and volcanic rocks are cut by a number of faults and fault zones which did not materially affect early mining operations, but, as undeground openings increased in size, the faults became more important factors in determining mining methods and procedure. Caving methods were adopted to take advantage of ground weakness in fault zones, and the effect of ground subsidence which resulted from the division of the ground 1nto large, independent blocks by faulting had to be considered in planning the sequence of mining of certain ore blocks. The faults have been divided into two classes: the longitudinal system and the cross faults, or &apos;breaks&apos; as they are termed locally. In addition to the two classes of faults, the zones of parallel ore fracture also control mining procedure, but to a lesser degree, in regard to caving or ground subsidence. A third structural feature which influences mining procedure is the mine dyke system. The longitudinal or main fault system roughly parallels the gab? bro contact and is made up of a number of branches and auxiliary fractures. The main fault itself is essentially vertical, but there are a number of branches and fractures on each side of it which, though parallel m strike, may dip as flat as 50 degrees toward or away from the main fault. The full width of the main fault system has not been determined, but it is known to extend beyond the zone of mine workings. A marked schistosity follows the main fault and both schistosity and chloritic alteration have been noticed along the secondary faults of this system. Several prominent orebodies lie along the main fault and its branches. The influence of the main fault system on mining is probably related more to subsidence than to actual cavi.ng, although it is effective in both.

Jan 1, 1950

By C. Villaseca, F. Penna, R. Villarroel

Acid mist is the undesired result of copper electro-winning (EW) process, generating a contaminated and hazardous environment in the working areas, as well as promoting high corrosion conditions for structures and equipment in the EW tank-house due to the buoyancy of sulfuric acid in aerosol form. Likewise, organic entrainments that occasionally occur in this process contaminate the cathodes, as well as increasing the risk of fire. LateralVex® and LateralFlow® are technologies that effectively and efficiently solve these problems, without affecting the usual activities of the operators, thus presenting a significant distinction with respect to other technologies that seek to solve these problems. Minera Antucoya, an AMSA group company, which produces 80,000 tons of electrolytic Cu per year, decided to install both technologies for its EW tank-house, LateralVex® in commercial cells and LateralFlow® in scavenger cells to keep both the acid mist and the organic entrainments under control. This paper presents the effects of applying these technologies in Minera Antucoya’s electro-winning plant, the challenges addressed, the difficulties encountered, the problems and opportunities that their implementation involved, as well as the surprising results obtained at the time of measuring the acid mist— less than one hundred’s part of the Allowed Weighted Limit—in samples taken with the plant operating at maximum current capacity. Additionally, the paper includes some of the improvements identified during the period, more than 3 years, in which these technologies have been in operation in Minera Antucoya. INTRODUCTION Electrowinning is the most used electro-chemical process in the hydrometallurgical industry for the recovery of highly pure metallic copper as its final product, which is formed in previous stages in an aqueous medium that goes through a selective process using organic solvents to separate impurities and concentrate the metal in a sulfuric acid solution. In the last stage, this solution goes through a process in which high- density current at a low voltage is applied, so that the metal in the solution will deposit in solid state on a plate, usually a stainless-steel plate. This last process involves the generation of other sub-products due to the electro-chemical dissociation of the electrolyte’s components, or to the addition of chemical additives, or due to specific physical conditions or lack of controls during the operation.

Jan 1, 2019