Search Documents

By M. D. Gerst

The degree to which copper will continue to be in an integral part of the world economy in the future will depend largely on the dynamics of global economic development, the primary and secondary copper resource stock, technological change, and potential environmental constraints. We have characterized the copper cycle of 1994 for all of Earth's regions and for the planet itself (T. Graedel et al., Environmental Science & Technology, 38, 1242-1252, 2004) and recently updated that cycle to year 2000. In this paper, we compare various features of the 1994 and 2000 cycles. The three largest-using regions, Asia, Europe, and North America, all increased their absolute rate of copper use between 1994 and 2000, and all increased the per-capita rate of copper use as well. Globally, the use of copper increased by about 32%, from 11.7 to 15.3 million metric tons, while population increased by only 8%. Various changes are seen in scrap trade, finished products trade, and other parameters of the cycle. We conclude by considering how the rates of technological change and growth in demand, especially in Asia, may influence the copper cycle in the years ahead.

Jan 1, 2007

By C. Cekerevac

The paper addresses some geotechnical issues related to the construction of the Deriner dam and HEPP. Design considerations and rock stabilization measures are presented for the excavations which took place in a highly fractured and weathered rock mass prevailing on site. Particularly, the shallow excavations for the overflow spillways tunnels are discussed. These present huge openings that are 12 m wide and 18 m high in portal areas, with an overburden of approximately 20 m, for which numerical finite element analysis and structural discontinuity analysis have been performed to ensure safe excavation process and future operation.

May 1, 2009

By M. Azzaz

In this paper, we report on new mechanical tests, at high temperatures, performed with a supposed better aluminium nitride (A1N) material, containing fewer oxygen. Our purpose was twofold: (i) check whether creep resistance is modified and hopefully enhanced and (ii) determine the elementary mechanisms controlling plastic deformation through transmission electron microscopy (TEM) observations of deformed samples up 10% strain in compression at elevated temperatures (1823-1923 K) under constant stress in the range 150¬250 MPa. Stationary rates are lower by an order magnitude than those previously measured in MN with higher oxygen content. All dislocations imaged by TEM look undissociated, which clearly relates the formerly observed wide dissociation to oxygen in excess.

Jan 1, 2004

By Claude Bourgoin

"The Copra massive sulphide deposit occurs as a continuous slab of ore dipping at approximately 40 degrees within a sericite schist formation. The orebody has been delineated over a distance of more than 5,000 feet down dip. This paper is mainly concerned with the mining procedure, and particular reference will be made to the use of steel mill holes and hydraulic roof supports. The gravel backfill line, which is operated both by gravity and hydraulically, is described. The paper mentions some of the operational problems, discusses the feasibility of longwall mining and presents the information obtained from stope testing."

Jan 1, 1966

By Robert B. Parsons

"No Canadian or his family is likely to escape the effects of proposals for pension reform tabled on October 9, 1986 by Finance Minster Michael Wilson. New tax rules are proposed for Registered Retirement Savings Plans (RRSPs), company pensions, and other forms of retirement plans. Draft legislation is expected to be released in the first half of 1987.IntroductionOver two years ago on February, 15, 1984, Mark Lalonde, then Finance Minister, tabled two White Papers. The first, Action Plan for Pension Reform, proposed improvements to the public pension system and increases in the minimum pension benefits standards to be mandated by the federal government. Since then changes have been made to the Old Age Security, Guaranteed Income Supplement and Canada Pension Plan programs. Also, benefits provided under pension plans subject to the federal Pension Benefits Standards Act have been improved significantly.The companion paper, Building Better Pensions f or Canadians, proposed to standardize and, in many cases, improve retirement savings through private plans by revising the tax rule s. The tax proposals in the Notice of Ways and Means released by Finance Minister Wilson on October 9. 1986 implement, with modifications, the tax treatment of retirement savings originally proposed in the May 1985 budget in response to that second paper."

Jan 1, 1987

By J. Stachulak

In recent years more emphasis has been placed on the control of nitrogen dioxide (NO2) emissions from mining diesel equipment. Worldwide, diesel engine regulations to control emission and protect the environment are also driving the development of the diesel engine technology to reduce oxides of nitrogen NOx (Nitric oxide, NO + NO2). NOx are toxic gases produced in mines during the operation of diesel equipment. Most of the diesel equipment used in underground operations are equipped with Diesel Oxidization Catalysts (DOCs) designed to reduce carbon monoxide (CO) and hydrocarbons (HC). The effects of DOCs on NO2 production from diesel powered equipment is not well understood. DOCs do not alter NOx concentration, but may promote the oxidization of engine exhaust NO to the more toxic NO2, thus increasing the undesirable NO2 exposure of workers in the mine environment. In 2012, the ACGIH reduced the NO2 TLV concentration value from 3 ppm to 0.2 ppm. Vale and CanmetMINING have been involved in several research projects to reduce diesel emissions exposure to workers. One aspect of the current program is to determine the effects of in-use DOCs on NO2 production. Several in-use DOCs taken from mining equipment were selected for testing in the laboratory using ISO 8178-C1 and mine LHD transient test cycles. The paper presents the laboratory test results and effects of DOCs on NO2 production. The results indicate significant reductions in CO concentration, by over 77%, while increases in NO2 varied from 46% to 315% based on the ISO 8178-C1 8-mode steady state test cycle. The mine LHD transient test cycle showed the same pattern, although the magnitude of CO reduction was less. Consequently, it is recommended the use of only those DOCs that have been properly evaluated and shown not to significantly increase NO2 emission in the environment be used on mine equipment.

Aug 1, 2013

By C. Doyle, D. M. Hoffman, C. Díaz, J. Hrepic, W. J. Koshut, R. H. Hanewald

"Recently, lining life of the INMETCO submerged arc furnace has been dramatically extended from an average of eleven months in the 1980s to a current record of 34 months. This paper summarizes test work and operating results describing the development and establishment of slag parameters that reduce corrosion of the magnesite-chrome refractory lining.The desired slag parameters are now maintained by utilizing waste streams as slag additives. This paper also discusses the successful evaluation of a rebonded-fused-grain magnesite- chrome refractory as a lower cost, more thermo-mechanically forgiving alternative to a fused-cast magnesite-chrome refractory that had been the refractory of choice in previous years at INMETCO.IntroductionSince 1978, INMETCO, a wholly owned subsidiary of INCO Limited, has been well known for recycling by-products from the production of stainless steel, namely, EAF bag- house dust, mill scale and grinding swarf. INMETCO operates the only smelter in North America dedicated to the recovery of nickel, chromium, and iron from hazardous and nonhazardous waste. The process was developed in the research laboratories of INCO. In recent years, the process has been successfully modified to accept a wider variety of other specialty steel waste streams including: spent pickling solutions, pickling and waste water treatment filter cakes, acid scale, carbon brick, spent bag-house bags, torch cutter dust, spent dolomitic and chromium-bearing refractories, and rechargeable nickel-cadmium batteries."

Jan 1, 1997

By The Staff

"IntroductionThe published information concerning treatment of uranium ores has been very limited as far as Canadian ores are concerned. Such information has dealt mainly with refining processes for concentrates or rich ores, designed to recover radium rather than uranium; these methods could not be economically applied to low-grade ores.The purpose of this paper is to describe treatment possibilities for some of the .ores that have been treated at the Mines Branch, and .to show how the character of these ores influences methods and results.What is a Uranium Ore?Prospecting for uranium has been extremely active during the past two years and a great many occurrences of radioactive minerals have been recorded. Such prospecting has been based to a large extent on the use of the Geiger counter in the fie1d. This equipment is an invaluable aid when the results are properly interpreted.Most definitely, indications of high radioactivity do not always prove the presence of a valuable orebody. First we have to determine:(1) Is the radioactivity due to uranium or to thorium. There is no immediate market for thorium.(2) Can the uranium in the ore be economically recovered.Chemical analysis is the most exact method of determining uranium content, but a fair estimate of the uranium, and also of the thorium, content can be made from the difference in gamma and beta activity. The Mines Branch guards against misinterpretation by determining both beta and gamma activities and, if more than a minor amount of thorium is indicated, then a Chemical analysis is made."

Jan 1, 1950

About Barrick Paste Backfill at Barrick Goldstrike Rodeo Paste Plant Cyclone Lab Testing Challenges and Lessons Learned Future Barrick Projects

May 1, 2013

By Thomas J. Ferree

"IntroductionThe objective of this chapter is to provide important criteria relating to the operation and maintenance of spiral concentrators and Reichert cones, so that optimum performance can be achieved and maintained in a mill circuit. Little space will be devoted to the theory of the forces of separation or the technical details of the devices, as that in(ormation is available from other sources. The discussions in this chapter will be presented in a manner that should be interesting and useful to anyone who may be exposed to these methods of gravity separation. It is most important for the reader to understand that each application of the equipment should be considered on its own merit, as no two suites of minerals respond exactly alike in mineral processing circuits. The information herein should be useful as a guide toward increasing the metallurgical efficiency of the processes, irrespective of the type of minerals being concentrated.It is highly recommended that certain tools be made available to the personnel responsible for metallurgical performance of the spirals and cones; these include a set of standard type laboratory screens, a medium quality petrographic microscope, and a vanning plaque or gold pan. These devices, when used in conjunction with a basic understanding of the mill circuit, provide immediate knowledge on the characteristics of any sample in the mill circuit. The information gained by visual evaluation of sized fractions of products can solve many of the basic problems of mineral beneficiation, and at the same time increase the interest of the non-technical personnel associated with the plant operation. There are many problems associated with obtaining satisfactory performance from a mill operation. Many of the problems have to be solved using a technical approach. Some of the problems, however, can be solved with practical knowledge and common sense. It is hoped this chapter can provide a guide to both techniques."

Jan 1, 1989

By Lloyd Buckingham

Barrick Gold Corporation (Barrick) has undertaken innovative methods of evaluating and improving the performance of grinding mills in several of its operations around the world. The results have been positive with some of the mines showing more than 20% net energy improvement leading to more than 43,000 tonnes per year reduction in CO2 emissions in four of the operations reviewed.

Jan 1, 2012

By Nabeel Khan

Annual oil production from the Canadian Oil Sands in Northern Alberta has been rising for several decades, and more ore and overburden are excavated each year from an increasing number of open pit mines. Overburden meeting certain specifications will be used to dam tailings and fill open pits, but the remaining material must be stored in overburden storage structures (OBSS). Well-designed overburden storage structures are more stable and cost less in the short- and long-term. The purpose of this paper is to explore OBSS designs that will be stable yet economical in the short- and long-term. The geological background of the site is briefly discussed, including the effect of each of the main geologic layers (recently deposited till and muskeg, Clearwater Formation clay shales, McMurray Formation oil sands, and the Devonian limestone) on the slope stability of the OBSS. Cost is considered in the analysis when balancing between minimizing costs (steeper slopes) and acceptable factors of safety (flatter slopes), all the while considering the financial consequences of failure. Potential failure planes are identified and probabilistic analysis is conducted on the critical failure surface. The variations in the factor of safety caused by varying pore water pressure, friction angle, and cohesion, are plotted and discussed.

Jun 1, 2012

By R. Holmwood, M. Faris, P. Holloway, M. Collins

Sulphuric acid addition is a major driver of the economics in the processing of nickel laterite ores by high pressure acid leaching (HPAL). Understanding the optimal acid addition rate is essential for the success of any HPAL operation, and this is especially true at Ambatovy, where the composition of the feed tends to vary significantly on a day-to-day basis. Most studies on the effect of acid on nickel extraction in HPAL have used laboratory testwork as their basis. Although these studies are invaluable in assessing the economics of a new project, they are limited by the range of ore composition that can be tested and the differences between the operation of the laboratory equipment and the commercial plant. To enable optimization of the acid addition at Ambatovy, operating data from the HPAL operation were obtained using OSISoft’s PI system and the data from several periods were examined to develop relationships between acid addition and nickel extraction. The initial relationships from 2014 focused on the acid required to achieve a target nickel extraction of 95%, with aluminum and magnesium in ore and feed slurry solids content as the major variables. As Ambatovy ramped up through 2015 and 2016, the calculated acid requirement was further refined to address the effects of HPAL temperature and retention time, and the oxidizing/reducing characteristics of the ore, and to generate acid requirement relationships as a function of ranges of nickel extraction. These relationships supported raising the target nickel extraction to 96% and enabled the development of an economic model between acid addition and nickel extraction.

Jan 1, 2017

By C. S. Ha, H. S. Choi, D. Y. Shin

POSCO installed a new 100 ton oxygen bottom-blown converter in 2013 for the development of new steelmaking process named as PS-BOP which is reading POSCO-Saarstahl Basic Oxygen Process. This process was developed by the collaboration research between POSCO and Saarstahl AG in Germany that is based on substantial increase of CO post combustion in a converter by blowing hot air from the top of converter. The collaboration research has been finished successfully in November 2013 with 17% decrease in hot metal ratio (HMR) when hot air was blown from the top of the oxygen bottom-blown converter. After the collaboration research the converter has been tried to be operated as oxygen top and bottom-blown converter to reduce bottom wear and to decrease production cost with increased use of low cost Fe source by the help of increased CO post combustion. The presentation includes experience on the start up of oxygen bottom-blown converter, HMR reduction trials with hot air top blowing and transition from oxygen bottom-blown to top and bottom-blown converter operation.

Jan 1, 2015

By A. Warczok, C. M. Diaz, A. Bergman, T. Utigard, M. Barati

The world wide consumption of energy is steadily increasing and by 2030 it is forecasted to grow by another 50%, leading to mounting political and economic pressures. For any pyrometallurgical operation, it is therefore paramount to investigate and implement methods to decrease the use of energy. In the pyrometallurgical processing of steel, copper, nickel and other high temperature metals, a large amount of energy is lost in hot off-gases, molten slags, mattes and molten metals. Most of this energy is generally lost during the cooling and solidification steps with very little focus on energy recovery or reuse. In this paper we will quantify how much energy is contained in the various slag streams, then review previous attempts and methods employed to recover some of this energy, and finally evaluate some novel technologies that could potentially be employed.

Jan 1, 2011

By J. W. Reynolds

Use of crushed waste rock recovered by sink-float separation from normal ore production for backfill is an established procedure at Commco's Sulhvan mme, Kimberley, British Columbia. Need for a safe method of placement in voids which were difficult to reach by gravity methods led to a co-operative venture with Radmark Engineering Ltd. in the development of a workable pneumatic transportation system for rock material. This paper reviews work done to date in a current program, and includes comments on the nature of the fill so placed, options for cementing such fill, implications for other aspects of mining and references to other applications of the system by other organizations who exchanged experiences with the Sullivan mine staff during the five-year period reviewed.

Jan 1, 1972

By Q. Li, X. -L. Lei

Accompanying global energy shortage and high energy prices, shale gas has been the focus of exploration and it has attracted great attention from both academia and industry. The combination of horizontal drilling and hydraulic fracturing enables the extraction of huge quantities of shale gas from impermeable shale formations. During the process of hydraulic fracturing, great amounts of water, sand and chemicals must be injected into the shale formation at a high pressure, which may trigger seismicity. Such events could occur due to the presence of faults or the reactivation of these potential faults. Shale is the main component of source rock in the Sichuan Basin, China, and has the greatest contribution to the natural gas of the basin. In order to investigate the fracturing mechanism of shale in the Sichuan Basin, China, a series of rock fracture tests under triaxial compression were carried out in the laboratory in order to investigate the hydraulic fracturing behavior in relation to the seismicity. Based on the high multichannel waveform recording system, the detailed spatio-temporal distribution of acoustic emission due to micro-cracking was used to examine the deformation and fracture behavior of shale. In addition, the effects of confining pressure on the deformation and fracture in shale under triaxial compression by acoustic emission monitoring and X-ray computed tomography were discussed in the paper. The experimental results indicate that the shale samples demonstrate brittle fracture behavior. The confining pressure has a great effect on the complexity of the fracture planes and the spatial distribution of acoustic emissions, but few contributions to the location of the major hydraulic fracturing plane. The foliation of shale plays a dominant role in the rupture process and the geometry of the major hydraulic fracturing plane. The high confining pressure increases the strength and restrains the deformation of shale during compression process. These results shed some light on the understanding of onset of hydraulic fracture initiation not only for shale gas exploration and production, but also for CO2 geological storage and underground energy storage.

Jan 1, 2015

By M. S. Badollet

"IntroductionASBESTOS FLOATS may be defined briefly as blends of air-borne particles of fibrous asbestos and dusts produced during the milling stages and collected by Cottrell precipitators, dust sheds, or bag-houses.The various grades of asbestos floats on the market contain fibrous asbestos particles ranging in length from microscopic to approximately 1/4-inch. The fines or dusts present in the floats are from 40 microns to 2 microns or less in cross-section.Airborne asbestos particles are of diverse length because they are collected at numerous places in the mill. There are: (1) dusts removed from dry rock storage bins, (2) dusts removed from rock and fiber screens, (3) particles from the tops of collectors, and (4) fines removed by suction from the processing equipment. Sometimes the airborne particles are kept segregated, so that there is a partial separation by gravity. This is accomplished by a series of dust chambers enclosed in a long, rectangular building. The longest and heaviest particles fall nearest to the air flow entrance, the smallest at a point farthest away and nearest the exit. Sometimes the air from the dust chamber building is passed through a series of bag-houses or electric :precipitators ,to collect the extremely fine particles which normally escape to the atmosphere."

Jan 1, 1952

By W. N. Roman

This paper will examine the challenges involved in ventilating and cooling South African mines, with particular emphasis on solutions to the issues of heat (generally associated with depth), mechanization and energy efficiency. Comparisons will be made with other international mining areas. Some of the deepest mines in the world are to be found in the South African goldfields. The Mponeng mine is approaching 4,000 m below surface, with virgin rock temperatures (VRT) of between 60°C and 70°C. Mining at these depths has only been possible with the use of large refrigeration plants supplying cold air, water and ice to the workings. In the Bushveld Igneous Complex, where most of South Africa?s platinum mines are located, similar VRTs are being experienced at significantly shallower depths. This is due to the different geothermal properties of the host rock between the two areas. Existing mines are being forced to go deeper and new underground mines are being planned and constructed in other areas with widely differing thermal conditions. South African metal mining has traditionally been labour intensive for historical reasons as well as for the narrow tabular nature of many ore bodies. Due to cost pressures and labour problems, some mines have been investigating the possibility of using mechanized equipment, both diesel and electric, to increase production and to improve efficiency. Studies have been carried out to determine the effect of the additional equipment on the overall ventilation system and some of the conclusions are discussed. The use of diesel equipment adds heat and pollutants to the ventilation air but, although electrical equipment has a lesser effect on the ventilation systems, it is generally less favoured due to claims of lower flexibility/manoeuvrability. Mechanization holds the promise of more concentrated mining activities but, with higher localized ventilation and cooling needs. Systems which will control the provision of air and cooling more effectively are required and are being implemented. In the 1990s and early 2000s, the South African economy experienced significant growth which was not matched by the growth in infrastructure. Consequently, at present there is a shortage of electricity generation capacity which affects large industrial consumers, including mines. Increasing levels of heat and mechanization will require more electrical energy for ventilation and cooling. There are many initiatives underway to save power or to shift consumption to periods of national low demand and these will be described.

Aug 1, 2013

By A. R. Pasieka, J. C. Wilson

"Compressed air still remains an essential source of power in underground hardrock mining. As a power medium it has a high convenience factor, although, in many cases, it is expensive to generate and maintain. Until new methods of breaking rock and/ or satisfactory alternatives to air-driven rock drills are developed, compressed air is indispensable. It is essential to utilize this source of power to a maximum by keeping all pneumatic tools supplied with air in adequate quantity and at optimum pressure.In search of the optimum operating air pressure, con-trolled drilling tests were undertaken at dynamic pressures ranging from 90 to 140 psi.Test results show the effect of increasing air pressure on: the performance of various jackleg drills at varying pressures, the life cost of drill steels and TC bits, and drilling efficiency at varying pressures. From the fore-going, a criterion is proposed for selecting efficient rock drills, and, also, optimum air pressure at each mine can be determined for its particular conditions."

Jan 1, 1966