Search Documents

By Jerry Ran

When multiple levels are mined in open stope mining with delayed backfill, mining underneath fill is inevitable to achieve higher rate of recovery if no sill pillars are left for the purpose of fill separation or partial ground support. This is particularly true when the orebody has low reserves per unit vertical distance. Instability of the exposed fill back causes stope dilution, production delay and possible equipment damage and consequently increases the mining cost. Previous studies have concentrated on fill mat stability in cut-and-fill and stability of fill walls in open stope mining. Workers are exposed to the fill back in cut-and-fill and therefore smaller open spans are normally adopted and the fill mat is reinforced. In open stope mining openings with large spans are designed, workers are not exposed to the fill back and its stability has to be maintained by fill of sufficient strength. However, the required fill strength is normally determined by considering different modes of fill wall failure. The fill back stability is usually not analyzed in the fill design process. The lack of analysis on fill back stability for open stope mining is mainly due to difficulties in relating the fill properties to the fill and stope geometry. In this paper a simplified wedge model is adopted to analyze stability of the exposed fill back in open stope mining with consolidated backfill. The proposed method calculates the factor of safety of the fill back against shear failure under known fill and stope geometry and fill strength parameters in order to assess the fill back stability. It can also be used to determine the required fill strength with known fill and stope geometry. The proposed approach is indirectly validated by mining experience and observations at two operating mines. In addition there are many factors affecting the fill quality and stope configurations in an operating mine. These factors have to be considered in the analysis of fill back stability. This situation is highlighted by presenting an actual mining case where the fill back failed due to factors commonly encountered in mining operations.

May 1, 2003

By R. M. Kleine

In the fall of 1968, Sheridan Geophysics leased the Renzy Mine property 50 miles northwest of the town of Maniwaki, Quebec. A 500-tpd flotation mill was dismantled at Belleterre, Quebec, trucked into the mine over a winter road and re-erected during extreme winter conditions. Approximately one billion gallons of water were removed from Renzy lake to expose the orebody. A 3,000-hp diesel generating plant and a self-supporting community were set up during the early part of 1969. This was a remark-able achievement considering that most of the work, including the pouring of foundations and the draining of the lake, had to be done during the winter months. Despite this, the project was completed ahead of schedule and one million dollars below budget. The mill is now treating an average of 800 tpd.

Jan 1, 1970

By A. Hashempour, D. Javani

"Selection of an optimal bit is a critical issue in drilling engineering. Specific energy (SE) and Cost per Foot (CPF) are the most common methods for evaluation of bit efficiency and optimal bit selection. The major shortfall of both methods is that they do not directly account for geological and geomechanical parameters of formations being drilling. In this paper, results of using the two foregoing methods are compared using Formation Drillability (FD) method, which directly accounts for geological and geomechanical parameters of a formation. This method combines various geological and geomechanical parameters and yields a dimensionless parameter indicating the formation drilling hardness (drillability). Results of this study show that the amount of energy, cost and time spent for drilling a unit volume / length of an identical formation may vary in different wells. This is due to the fact that geological and geomechanical characteristics of a formation may vary among wells and even within short intervals of a single well. Therefore, an optimal bit may not be appropriately selected, if drilling and economical parameters are the only factors considered and the formation geological and geomechanical specifications are ignored.INTRODUCTIONMany authors such as Bilgesu, Al-Rashidi, Aminian, and Ameri (2000) and Clegg (2006) conducted research in the evaluation of bit performance and optimum bit selection. Almost all of them tried to establish a good relationship based on geomechanical parameters. Primary examples are the research done by Ubaldi (1999), Macini, Magagni, Da Dalt, and Valente (2007)."

Jan 1, 2015

By A. Rodriguez-Prado, R. L. Legge, W. C. Lennox

ABSTRACT It is possible to adequately describe chemical reduction of hexavalent chromium, Cr(VI), in industrial and mining wastewater in constructed wetlands by applying different kinetic models (e.g., halforder, second-order). Accounting for hydraulic transport of contaminants in reduction equations can also improve such description. The authors developed an explicit advection-dispersion bulk flow equation and applied it to model Cr(VI) reduction in laboratory wetland mesocosms. The results indicated that the model adequately described wetland exit Cr(VI) concentrations and Cr(VI) reduction, representing an improvement over the commonly used graphic method and potentially improving the wetland design.

Jan 1, 2014

By W. E. Hale

An area of about 7,000 square miles within the eastern part of the Grenville Sub-province is underlain chiefly by granitic gneisses. There are, however, some exposures of mafic rocks which warrant further investigation, and some attractive structures, particularly basins, which deserve additional economic consideration. T HIS paper describes in a very general fashion the economic and geological features of an area of about 7,000 square miles on the north shore of the Gulf of St. Lawrence in the eastern part of the Grenville Sub-province (Figure 1). The scarcity of published geological data on this part of the Cana-dian Shield (DePuyjalon, 1899 and Longley, 1944) justifies the presentation of these tentative results. It should be appreciated, however, that the information which follows was acquired in a rapid reconnaissance designed specifically to out-line what might be interpreted as favourable geological environments for the occurrence of economic minerals, rather than to produce an authoritative analysis of the geological history of the region.

Jan 1, 1962

By E. R. Rivenbark

"The coal handling plant represents an investment of about $100 million in coal handling and storage equipment. The coal receiving is done by a continuous ship unloader that can handle ships in the 60 000 T range at Q rate of 1750 /ph. A unique feature in the system is a stacker/reclaimer unit which will work inside a dome storage structure. The coal for the unit will include any low sulphur coal that can be delivered by sea at an economical price blended with New Brunswick high sulphur coal.ThE flue gas scrubber is a wet limestone system capable of 95% SO2 removal. The scrubber will utilize about 150 000 tonnes of limestone per year and will produce commercial grade gypsum by the forced oxidization method.IntroductionWith the need for new generating capacity being required, New Brunswick Power reviewed, in 1985, its options for the next unit. The study indicated that the most attractive option for New Brunswick Power would be a coal-fired unit capable of receiving imported coal at a sea port. The site selection process resulted in three site options being considered.The existing Coleson Cove and Dalhousie sites, and the Belledune site were considered. To meet load distribution needs, it was then decided that the unit had to be located in the northern section of the province, thus eliminating the Coleson Cove site. The Belledune site was selected because it had the capacity to have additional units added where as the Dalhousie site would have only been able to accommodate one unit"

Jan 1, 1994

By H. Houali

Corrosion is an electrochemical process that causes degradation and deterioration of various steel works (pipelines, drains, cisterns) whether they are buried, immersed, or not. Worldwide, we estimate that corrosion destroys a quarter of the annual production of steel at a rate of 5 tons per second. Several techniques are used to protect against corrosion. Among these processes, Cathodic protection, which is regarded as the best technique to assure the protection of steel, works against this phenomenon. This is achieved either by a system of reactive anodes, or by the technique of impressed current protection or other techniques. Before any installation of cathodic protection, a preliminary study and pre-evaluation of certain parameters must be made. In the present work, we will present an example of dimensioning of an installation of cathodic protection by imposed current of a pipeline using solar energy, where we discuss the following items: ? Evolutions of the potential as well as current along the pipeline and their respective expressions deduced from the laws known as telegraphists; ? Range of protection (potential of protection along the pipeline); ? Influence of the isolation resistance of the coating on the range of protection; Effect of the aging of the coating and its influence on the current of protection

Jan 1, 2005

By G. E. Bogin, C. Strebinger, J. F. Brune

"Evidence shows that methane gas emanates from the mined-out area or gob of a longwall coal mine and can travel towards the working face, posing an explosion risk. Since the gob consists of varying levels of compacted rock, many researchers have modeled fluid flow through the gob as a Darcy-type porous media with a specified porosity and permeability. When studying methane gas explosions near the gob fringe, the Darcy flow assumption may not be applicable to describe the methane flame interaction with the gob. Computational fluid dynamic studies were performed modeling methane flame propagation across a simulated gob which was modeled as both a Darcy porous medium and as discrete rock objects with varying sphericity. Modeling the gob as a Darcy porous medium results in unrealistic methane flame propagation since the porous media assumption does not consider any differences in rock size and/or distribution. Additionally, the porous media model does not allow for ignition within and subsequent flame propagation through the porous medium, which must be modeled to understand the potential for methane gas explosions in the gob area. Modeling the gob as discrete rock objects produces more realistic methane flame dynamics and agrees with experimental observations. Modeling results show flame propagation across circles, hexagons, and squares, meant to represent rock rubble in the gob, produce different levels of turbulence which affects methane flame propagation velocity. This research demonstrates that modeling methane gas explosions in a longwall coal mine environment, specifically near the gob area, requires modeling obstacles, such as rock rubble, as discrete physical objects to capture the complex coupling of fluid dynamics, thermodynamics, and heat transfer. INTRODUCTION Although there are methods to mitigating methane accumulations in a longwall coal mine, explosive gas zones (EGZs) of methane and air may exist and pose an explosion risk to nearby miners and equipment (Brune, 2014) (Karacan, Ruiz, Cote, & Phipps, 2011). In the event of an explosion, the resulting methane flame and pressure wave can be catastrophic as evidenced by the Upper Big Branch explosion in 2010 that killed 29 miners (Page, et al., 2011). Since the mining process is transient, it is difficult to determine exactly where these EGZs exist, but investigative reports show in many cases, these EGZs can be near the working face, behind the shields, or within the gob area (Brune, 2014) (McKinney, et al., 2001). Additionally, miners have recounted seeing flames moving back and forth within the gob and under the roof supports (McKinney, et al., 2001) and in other cases, anecdotal evidence of hearing small pressure pops deep within the gob area (Brune, 2014)."

Jan 1, 2019

By Joseph H. Harris

Shebandowan Mine presents a unique opportunity for the mining industry to demonstrate its willingness and ability to use electrical energy effectively. The mine is a typical 250D-ton/day operation supplied by a i5-MVA power transformer. it is a recent, up-to-date design and operates on a four-day/week, two-shift/day basis. The paper outlines an energy profile based on historical data. It accurately describes the individual and total energy input For: (1) production and non-productive junctions; (2) production and down-time periods; (3) peak and average activity levels; and (4) principal energy utilization equipment. A comparison is then made of production data to electrical data, and production and electrical data to design data. The paper concludes that energy management has an important benefit for the mining industry by assisting in maintaining a competitive operation through reduced costs and fewer production slow-downs in the event of energy shortages.

Jan 1, 1979

By G. Mucsi, J. Faitli, K. Bohács

"The authors developed an online tube rheometer to supplement a Netzsch MiniCer (Netzsch GmbH, Germany) stirred media mill in order to monitor online the rheological characteristics of the suspension and therefore the result of grinding during the process. Previously it was demonstrated that the above measuring system was working appropriately based on the preliminary tests. The product related stress model was applied for the evaluation of the grinding results. It was found that the suspension concentration and the change of the material properties during grinding, consequently the rheology strongly affects the grinding result, i.e. specific surface area, median particle size as well as specific grinding energy. The tested model limestone – water suspensions behaved Newtonian initially, then after a given grinding time their properties had changed and they become Bingham plastic. INTRODUCTIONStirred media milling now is a common practice to produce fine and ultrafine granular materials for different purposes. With an increasing demand of ultrafine powders for industries (Kwade, 1999), wet and dry ultrafine grinding has been increasingly used in various fields, such as minerals (Mucsi, Rácz, & Mádai, 2013)(Rácz, 2014), ceramic materials (Becker & Schwedes, 1999), pigments (Ohenoja, Illikainen, & Niinimäki, 2013), chemical products (Baláž et al., 2013), microorganisms (Kwade & Schwedes, 2002) and pharmaceutics (Afolabi, Akinlabi, & Bilgili, 2014). It is well known that suspension rheology affects the wet comminution of materials (He, Wang, & Forssberg, 2006a). The rheological behaviour of the suspension containing the ground particles might indicate the level of interparticle interaction or aggregation and therefore it is an important variable factor of the process control (Muster & Prestidge, 1995). The influence of the rheological behaviour of mineral suspensions on their grindability has attracted more and more interests and attention, especially on ultrafine grinding performance (He, Wang, & Forssberg, 2006b) (Bernhardt et al., 1999). However, there are still many issues concerning the machine and the process for the different applications. When grinding is effective and the particle size range decreases significantly, the circulating suspension is becoming typically non-Newtonian. The changed rheological behaviour and the increasing rheological material parameters can negatively affect the grinding efficiency; therefore it is an important issue. Ultrafine stirred media milling as well as solid-liquid two phase flow have been studied for a long time at the Institute of Raw Materials Preparation and Environmental Processing of the University of Miskolc. Regarding ultrafine grinding the research is focusing on the description of materials’ grindability (energetic aspects) both in wet and dry circumstances (Mucsi et al., 2013; Rácz, 2014). Concerning rheology, the three measuring pipes tube rheometer was developed decades ago (Faitli & Gombköto, 2015). So far many different solid materials from all over the world had been tested in this rheometer (Faitli & Gombköto, 2015). Main aim of these tests was to gain basic data for large scale hydraulic transport applications. Among the many stirred media mills there is a Netzsch MiniCer mill at the Institute. It was reasonable to combine the two fields together, and the goal of the research presented in this paper is to develop an online tube rheometer for the Netzsch mill and to carry out grinding and rheological testing simultaneously."

Jan 1, 2016

The Silvermines area of north County Tipperary in Ireland has experienced mining activity for over a thousand years, with lead, zinc, copper, barite and sulphur being extracted from a series of Carboniferous limestones. The last mine to operate in the area was closed in 1993. A legacy of contamination and derelict surface structures remain. Following the death of cattle in the vicinity in 1999, a governmental Inter-Agency Group was established to conduct an investigation. The ?Silvermines Rehabilitation Project? resulted, and included a proposal for the development of a Mine Waste Management Facility (MWMF) to act as a repository for waste materials from problematic sites across the area. The nature of the setting supported an effective solution from both a cost and performance perspective; and with limited maintenance requirements. Locating the MWMF where most wastes were identified would help minimise handling and relocation of materials. This position coincided with an area of artesian groundwater pressures. The resulting MWMF design consisted of a perimeter engineered embankment with the crest elevation designed to just exceed the groundwater piezometric surface. The base would remain unlined and groundwater permitted to rise up into and saturate the contained in-situ tailings deposits and imported mine wastes. The proposed system thus benefited from the ?wet cover? approach to minimising further oxidation of wastes and metal leaching, but without the usual accompanying outward hydraulic gradient and leachate management issues. A sub cap drainage layer with downstream outlet was incorporated to prevent any possibility of hydraulic rupture following an unexpected rise in groundwater heads. Leakage rates from the MWMF were deemed to essentially be driven by surface infiltration rates alone (characteristic of a ?dry cover? approach), with the proposed composite capping system simulated to perform at an infiltration rate of less than 1 mm per year. A toe drain was incorporated with the perimeter containment system, and this collection together with diverted neighbouring drainage was directed under gravity to a dedicated Passive Treatment System (PTS). Overall, effluent water quality from the PTS has been predicted to reflect an annual mass metals removal in the order of 95% below baseline.

Aug 1, 2013

By S. S. Teal, W. W. Weber

"AS THE TITLE implies, this paper will deal with the unusual rather than the standard practices as employed . at the property of North Rankin Nickel Mines, Limited. Fortunately •the mining, with the exception of permafrost conditions, and the milling practices, are the normal approaches dictated by the size, type, and character of the orebody. The unusual aspects are linked directly or indirectly to the isolated location and are •principally ancillary requirements or services covering a broad range from climate to supplies and from finance to entertainment. It is our intent to cover the more salient points of interest together with a brief description of the general operation.To understand the primary motivation of the mine, it must be made clear that North Rankin was conceived as a foothold in the Canadian North, that region embracing 40 per cent of the Dominion which ex-tends north of the commercial tree-line and which includes nearly 50 per cent of the Precambrian Shield, our mainstay of Canadian mining. Secondly, this project was born in an atmosphere of premium sales in the nickel markets, assuring a rapid pay-back of the heavy •capital expenditures. And finally, it has •been coddled through the stark reality of a competitive metal market with the hope and trust that the experiences and achievements will lead over the bill to a bigger and better mine in this virgin territory. This is the briefest story of the mine's history, but it pays tribute to the many people who, in thirty years since .discovery, have championed this project."

Jan 1, 1959

By N. Parnian

"Carryover of caustic soda (NaOH) in the steam path caused catastrophic failure of superheater 304H stainless steel tubes in a steam generator and led to an unexpected shutdown after just five months of continuous service of petrochemical following the start of production. The cause of the failure was studied, with a focus on the formation of sigma phase in the weld joint and effect of caustic embrittlement on stress corrosion cracking (SCC). The cracks were examined at the seam weld, heat affected zone (HAZ), and Ubend areas. Hardness was measured for the base metal, HAZ, and weld metal, and microstructures were examined using optical microscopy and scanning electron microscopy (SEM). Crack initiation is attributed to gouging on the precipitated carbide at the HAZ and also the formation of sigma phase in the weld metal, as shown by energy dispersive X-ray (EDX) analysis. In addition, cracking was propagated by caustic embrittlement because of residual stresses and hammering. Finally, the characteristic feature of fracture was illustrated by SEM fractography, and consists mostly of intergranular SCC and some quasicleavage transgranular. INTRODUCTIONThree key factors are needed for the initiation and propagation of intergranular stress corrosion cracking (IGSCC): a susceptible material, a corrosive environment, and sufficient stress. Although austenitic stainless steels are susceptible to sensitization and IGSCC, they are widely used in boiler and superheater tubes because of their high corrosion resistance, high oxidation resistance, acceptable mechanical characteristics at elevated temperatures, and low cost.Sodium hydroxide is injected to neutralize acidic constituents in the steam path, but caustic can concentrate in boiler tubes and attack the surface metal (known as gouging) even traces of caustic in the steam can deposit on surfaces and cause local concentrations of several percent (ASM handbook, 1992). Not only sensitized grains but also sigma phase formed in the weld metal can initiate caustic cracking. In this research, the cause of the failure of 304H stainless steel superheater tubes in a methanol petrochemical plant in Iran was studied with a focus on the effects of caustic embrittlement on IGSCC."

Jan 1, 2012

By Sergio Cattalanl, Francis Chartrand

"The geology and origins of volcanogenic massive sulfide (VMS) deposits in the Abitibi belt of northwestern Quebec have been the subject of discussion since the discovery of the Horne orebodies in Noranda in 1923.The present Noranda version of the VMS model characterizes the ideal deposit as a stratabound, base-metal accumulation that is in close spatial relationship with hydrothermal alteration and stockwork zones, felsic lava domes, coarse phreatic-pyroclastic breccias, and subvolcanic intrusions that characterize vent- and proximal{acies submarine volcanic environments. Deposits tend to occur in a favorable stratigraphic interval within a mining camp, and this is well-documented in the Rouyn-Noranda and Matagami camps.However, in recent years many VMS deposits have been shown to deviate from the ideal Noranda-type. For example, the Ansi/ deposit is characterized by sulphide-bearing alteration zones that extend far above the massive sulfide lenses, and by abundant magnetite immediately underlying massive sulfide. The Horne deposit appears to lack the typical chloritic alteration pipe underlying the massive sulfide lenses, as well as laterally-equivalent exhalite horizons. The Horne and Quemont deposits, besides being the two giants of the camp, are particularly rich in gold, whereas others, such as WaiteAmulet and Millenbach, have low gold values. Finally, some deposits in the Noranda camp, such as the Ansil, Corbet and Mobrun mines, are outside the favorable stratigraphic interval. Therefore, it would appear that part of the key to renewing base metal reserves in northwestern Quebec is the use of evolving descriptive-genetic models that incorporate geological variations like those cited above."

Jan 1, 1990

By Glenville A. Collins

IN 1932, Horace Onyett at Oroville, California, built a practical floating washing plant along the general lines as now known, using a 24 in. by 12 ft. trammel; it was fed with a ½ yard dragline bucket, rated then at 200 yards per day. Onyett dubbed his plant a 'Doodlebug' which name has clung to this type of operation ever since. In general, the 'Doodlebug' dredge is the outgrowth of the depression of 1929, wherein many dirt contractors had surplus idle equipment and a few of them ventured to use it for placer mining. Many such plants were impractical and poorly designed and adapted often to locations not suited to the purpose. However out of the general idea came refinements until today dragline dredging has a very definite place in the gold production of the world. Many of the early operators, being mainly contractors without mining experience or technical knowledge of gold saving, geology, or mechanical design, naturally went through stages of trial and error until a workable unit became standard practice. Credit should be given Bodenson Iron Works of San Francisco, who did a notable job of pioneering and building of floating washing plants; also, to Lord and Bishop, contractors of Sacramento, who were among the early operators, and to several others who built and rebuilt their plants until the weak spots were strengthened to take the beating required, and yet deliver a high degree of efficiency.

Jan 1, 1945

By C. Edwards

ABSTRACT: Milling operations in northern Saskatchewan’s Athabasca Basin have produced uranium continuously since 1975. During that period, the Athabasca Basin has been one of the world’s premier uranium camps, yielding more than 660 million lb (299,370,964 kg) of U3O8. In this paper, the author describes former and current milling operations and discusses why and how the milling process has changed and developed over the past 35 years. The author’s considerations for the future of uranium extraction in the Athabasca Basin conclude the paper.

Jan 1, 2012

By M. Kreuh

Crystalline Mg(OH)Cl and amorphous Mg2(OH)3C1 were successfully isolated from a hydrolyzed molten salt electrolyte sample in this work, It was found that the chemical form and crystallinity of the hydroxylchloride were controlled by the cooling rate of the molten sample when it was taken. Crystalline Mg(OH)Cl could only be obtained by cooling the molten electrolyte sample at a rate not faster than 0.6 °C/min, Upon more rapid cooling, the hydroxylchloride species precipitated as Mg2(OH)3Cl, The behavior of these solid hydroxylchlorides when contacted with fresh and non-hydrolyzed molten electrolyte at 550°C was also examined, It was found that the Mg(OH)Cl rapidly dissolved in the hot electrolyte and did not decompose into MgO at that temperature as would be expected from the literature, The dissolution rate of solid Mg2(OH)3Cl was found to be so slow by comparison that it resulted in the complete decomposition into MgO which thereafter was incorporated into the electrolyte as a suspended solid phase rather than dissolution.

Jan 1, 2004

By J. M. Hollicky

The economical processing of wet and sour natural gas presents a problem due to the seasonal demand for natural gas. The plants must be sized to handle the peak loads but may only operate at half capacity on the average, in which case the sales value of sulphur and hydro-carbon liquid by-products cannot support the operating and capital costs of the plant. This must result in an increased price for the gas. This problem was solved by Pacific Petroleums and Westcoast Transmission in the design of their pipeline and plant facilities now operating in the Peace River area, where there are both wet and dry gas fields. By .building a plant to process sufficient wet gas to pro-vide the base load requirement, and by drawing on the dry gas fields for peak loads, an optimum economic operation was ?possible. The sulphur, L.P.G., and gasoline produced not only are able to support the operating and capital costs of the pro-cessing plant, but were instrumental in the sharp drop in retail prices of these commodities in the area. The sour gas and condensate is gathered from the fields in the area and transmitted in a two-phase gathering system to the gas processing plant at Taylor, B.C. The condenrnte is knocked out in inlet scrubbers. Hydrogen sulphide and carbon dioxide are removed in an amine scrubbing unit. The hydrogen sulphide is stripped from the amine and is sent to the Jefferson Lake Sulphur Company's plant which produces sulphur by the partial oxidation of the hydrogen sulphide. The natural gas, now sweet, is processed in an absorption unit to recover additional liquids, before being de-hydrated to remove water. It is then sent to Westcoast's main c8mpression station. The condensate recovered in the inlet scrubbers and the liquid re-covered in the absorption unit are fractionated to remove fuel gas, used in the plant, and to produce pro-pane, butane, and naphtha. The pro-pane and butane are scrubbed with caustic soda to remove hydrogen sulphide. The naphtha is treated with hydrogen in a unifiner unit to re-move sulphur compounds completely, and is split into a light and heavy naphtha. The heavy naphtha is .catalytically reformed to produce a high-octane blending-component. These fractions are blended with components produced from crude oil at the Dawson Creek refinery to produce a high-quality balanced gasoline with special attention being paid to volatility for ease of starting, warm up, and engine cleanliness, and octane for power and ?performance.

Jan 1, 1958

By K. Scalise, M. Teixeira, K. C. Kocsis, J. Parrish

"This paper aims to introduce and discuss a newly developed algorithm, which can be uploaded on smart watches and other mobile devices to inform and protect underground personnel working in hot and humid environments. Using this algorithm, the metabolic rate (M) of a worker can be determined in “real-time”. In addition, besides warning signs and alarm signals emitted by the smart watch, the algorithm has the ability to determine work-rest time periods based on the worker’s physiological parameters (e.g. age, height, weight, gender) and the climatic parameters (Td, Tw, flow velocity). This paper also investigates whether a re-designed auxiliary ventilation system can provide appropriate work conditions in the production stopes. INTRODUCTION An underground environment with high temperature and humidity conditions generated from various heat and moisture sources can significantly affect the thermoregulation processes of the human body. This can lead to heat-related illnesses such as heat rash, heat cramps, heat exhaustion, and heat stroke. Heat stroke is a serious illness that carries a high risk of fatality, if the underground workers are not immediately treated and the climatic conditions are not corrected (McPherson, 1993). There are two methods used to control the climatic conditions in underground mines: (1) Using ventilation and cooling systems to reduce the thermal stress on the mine workers, and (2) Reducing the heat transferred to the ventilating air from major sources such as: strata, auto-compression, mining equipment, groundwater, blasting, etc. The heat from strata and auto-compression is transferred to the ventilating air at varying degrees, based on factors such as the virgin rock temperature (VRT), the thermal properties of the surrounding rock formations, and the surface air temperature. However, the use of mining equipment and blasting processes can be managed to reduce their contribution to the mines’ overall heat load. To provide appropriate work conditions, selecting the most suitable cooling method depends on the level of heat to be removed, the location of the problem areas, and economic constraints (Brake & Bates, 2002; McPherson, 1993). Because every mine is unique, it is essential to monitor the climatic conditions to select the most appropriate method of cooling. A majority of the time, simply adjusting or re-designing the auxiliary ventilation system can efficiently remove the heat and dilute the contaminants. This may involve moving the ducting system, changing the size of the duct, changing the size of the auxiliary fan, or switching from forcing to an exhausting fan arrangement. If the required air volumes are higher than the existing primary ventilation system can supply, other measures may need to be taken to increase the airflow delivery. This may include regulating the flow in some areas of the mine to increase airflow to the desired area, adding booster fans, or replacing the primary fans."

Jan 1, 2019

By A. Ashrafi

The electrochemical deposition of polypyrrole coating on different pretreated aluminum-alloy 7075 substrates was carried out using cyclic voltammetry, The pretreatment of specimens consisted of mechanical polishing and/or electrochemical etching, In the latter case, an aqueous solution of phosphoric acid and ethanol was used, The electrodeposition solution was 0,25 M pyrrole and 0,1 M oxalic acid in double-distilled water, The cyclic voltammetry scan rate used was 700mv/s, Morphology of the coatings was examined using scanning electron microscope (SEM), Using the Tafel experiment, corrosion resistance of the coated substrates was investigated in 0.1 M NaC1 solutions, Results obtained revealed that electropolymerization of polypyrrole on 7075 aluminum alloy would increase the resistance against corrosion in 0,1M NaC1 solution, Also it was observed that, compared with mechanical polishing, electroetching pretreatment would be more effective.

Jan 1, 2005