Search Documents

By Frank Baczek, R. Q. Honaker, D. P. Patil, B. K. Parekh

Fine refuse slurry impoundment is a requirement for the coal industry to dispose the fines. Impoundment maintenance is an on going problem for the coal industry and its breakage creates environmental as well as financial problems. Deep Cone thickener technology which has been successfully applied in the alumina industry to dewater red mud was evaluated for fine refuse slurry. Preliminary obtained in a pilot-plant test showed that properly flocculated conventional thickener underflow slurry could be thickened to about 52.5 wt % solids and could replace belt filter press. The Deep Cone thickener was also found to dewater clean coal slurry to about 70 wt % solids. Further testing of the unit at other coal preparation plant is in progress.

Jan 1, 2004

"Shales play a major role in the stability of slopes, both natural and engineered. This paper attempts to provide a review of the state-of-the-art in shale slope stability. The complexities of shale terminology and classification are first reviewed followed by a brief discussion of the important physical and mechanical properties of relevance to shale slope stability. The varied mechanisms of shale slope stability are outlined and their importance highlighted by reference to international shale slope failures. Stability analysis and modelling of anisotropic rock slope masses are briefly discussed and the potential role of brittle rock fracture and damage highlighted. A short review of shale slopes in open pits is presented.INTRODUCTIONShales have been stated to form approximately 58% of sedimentary rock so it is not surprising that they are frequently encountered in both natural and engineered slopes. They represent challenging environments for slope stability due to the wide variation in their engineering properties, their changing behaviour with time due to geomorphic processes and the variation in the failure mechanisms as a function of both stratigraphy and tectonics. An extensive body of literature exists on the terminology and classification relevant to shales; it is not possible in the scope and length of the current paper to review these works in detail and the reader is referred to Farrokhrouz and Asef (2013), Bell (2000) and Goodman (1993) for detailed discussions. It is arguably the case that no universally accepted classification of shales exists today and depending on the field of application the terminology varies widely. Shales in slope stability, for the purpose of this keynote paper, are taken to include material varying in properties from weak rocks to soils and therein lies one of the most challenging aspects in shale slope characterisation for engineering purposes. They have been classified as “rock-like” or “soil-like’, (Underwood 1967) or compacted and cemented, Table 1, Yagiz (2001). Classifications have considered numerous factors including composition, cementation and a wide range of engineering properties.The propensity of shales to degrade with time due to geomorphic processes has resulted in an important aspect in their classification, that is, the attempts to incorporate slaking, durability and swelling and softening behavior through purpose developed testing methods (Gamble 1971, Morgenstern and Eigenbrod, 1974). Figures 1 and 2 show examples of terminology used to describe argillaceous materials and some proposed engineering classification schemes (Grainger 1984 and Bott 1986). Corominas (2014) provides a recent classification of argillaceous rocks and their durability relating five stages of slope deterioration to the texture of the rock on Ternary diagrams. No attempt will be made here to discuss the merits of the proposed terminology and classifications, suffice it to say, that the controversy and flux surrounding these issues is a strong indicator of the complexities in the behavior of these materials. In this paper the author will consider slope stability in the materials indicated in Table 1, Figures 1 and 2 without undue focus on terminology. At the lower strength limit of shales the engineer must design slopes using the principles of soil mechanics which may vary from the simple Mohr Coulomb plasticity constitutive criterion to modified critical state models, some even attempting to incorporate softening behaviour in the weaker clay shale materials. Given the transitional nature of shale materials several workers have treated overconsolidated clays and clay shales using concepts such as peak and residual shear strength, brittleness index and softening. Martin and Stacey (2013) provide a useful review of the importance of weak rocks in open pit mining, with mudrocks as a specific member, and note the importance of delayed failure, progressive failure and loosening in the stability of"

Jan 1, 2015

"HPGRs operate in a wide array of applications in mining and minerals. These range from relatively coarse crushing of copper and gold ores at one end of the spectrum to the processing of fine iron ore pellet feed and fine industrial mineral products at the other. Traditionally these circuits involve the treatment of relatively moist materials in pre-grinding circuits; using single stage HPGRs in open circuit or as a closed circuit operation with screening or partial product recycle. More recently, HPGR is increasingly deployed in dry grinding in combination with air classification. The high throughput demonstrated by larger HPGRs has stretched the application towards coarser size reduction duties for a number of new projects. At the same time, the basic principle of inter-particle crushing for generating a product with a high fines proportion gives ground to investigate applying the technology further towards finished product duties. The advantages that HPGR brings are clear. Multi Stage grinding enables energy efficient size reduction across more of the comminution circuit. Primary HPGR serves for a coarse grinding duty, whereas a secondary HPGR is geared towards generating a fine product for downstream processing or even a finished product. This publication summarizes some of the features of staged HPGR circuits and discusses some examples of operating and projected applications.INTRODUCTION In most HPGR applications, the grinding units are used as a single process stage, either in open circuit, such as for pebble crushing [Rose 2002, Westermeyer 2000, Van der Meer 2015] or in closed circuit with classification [Van der Meer 2009, 2012] or product recycling [Van der Meer 2010]. Where a higher plant capacity is required, the HPGRs are commonly installed in multiple lines in a parallel arrangement [Parker 2005, Koski 201, Vanderbeek 2006]. HPGRs can take a wide range of feed size distributions, and grind this down to a product with a high fines content. In general view, there is a limit on the size reduction range that even an HPGR can provide. Grinding down from a very coarse ore (e.g. 70-100 mm) to a very fine product (e.g. 100 microns range) is stretching the ability of a single stage HPGR circuit. Fine grinding generally requires a classification stage that returns the classifier oversize to the head of the HPGR circuit. From one point of view, it can be demonstrated that when recycling a large proportion of fines and middlings back to the HPGR feed results in an effective feed with an overrepresentation of middlings and fines, which will eventually reduce the grinding efficiency and consequently result in an increased recirculation mass flow [Van der Meer 2014]. From another point of view the large recycling mass puts a strain or even a limit on the capacity of present-day conveyor capacity."

Jan 1, 2018

By van der Meer. F. P.

High Pressure Grinding Roll (?HPGR?) technology is applied in a broadening range of minerals processing applications for relatively wet or moist materials. HPGR grinding of dry material or involving drying and air classification is more common, for example in cement manufacturing. A number of minerals processing plants are also operating with dry material, either due to process reasons, such as considerations of preceding or subsequent process stages, or as dictated by local conditions of arid areas and scarcity of water. The present world-wide expectation of decreasing availability of water supply urges us to look for alternatives that minimize water consumption. Recently established and envisaged future HPGR applications with dry ores have indicated that the technology of dry crushing and classification as practiced in cement and limestone grinding can be applied in minerals processing. Moreover, dry technology could very well be applied for generating a final fine product at sizes near or below 100 microns, as may be required for beneficiation by, for instance, flotation, magnetic separation or tank leaching. Dry HPGR grinding requires special attention in maintaining suitable process economics, when considering power input in grinding, drying and classification. In some cases, HPGR capacity and roll surface wear life may be negatively affected by a lack of moisture in the feed. This publication summarizes some of the features of, and experiences in dry HPGR applications. This includes design aspects of the classification system and discussion of the wear protection of the roll surfaces. The paper also includes examples of operational experiences of dry practices in minerals processing and cement plants.

Jan 1, 2012

By H. W. Parsons

Several low-temperature, dry chlorination processes for the treatment of sulphide minerals are reviewed, in a chronological order. These processes include the following: the Swinburne-Ashcroft, Baker-Burwell, Maim, Comstock-Wescott (Aldermac) and the Mitterburg Mining Process. Dry chlorination investigations at the Canadian Mines Branch (now CANMET) and the U.S. Bureau of Mines are discussed, as is a proposed process by the South Africa National Institute for Metallurgy. The techniques used in the process are discussed, as are the shortcomings, problems and failures of the methods.

Jan 1, 1978

By Gyan S. Rajhans

"The strategy of fibrous dust sampling is discussed, various sampiing methods are critically reviewed .and their application to coal dust is demonstrated. Fibre counting is described in detail. An attempt is made to explain the basis of determining the threshold limit value of asbestos and other dusts. The paper also discusses such dust control methods as enclosure of the process, effective local exhaust ventilation, segregation, substitution, wet processing and continuous monitoring of the return air for recirculation."

Jan 1, 1970

By R. Rumpold, J. Antrekowitsch

"The continued increase of the automobile production leads to a higher platinum, palladium and rhodium (PGM) demand. Due to the high value of the PGMs the recycle of these metals from automotive catalysts is of special interest. Pyrometallurgical processes, which are only focused on the PGMs, represent the state of the art of automotive catalysts recovery. However, hydrometallurgical recycling processes offer additional recovery of other valuable metals and compounds. The method presented in this paper is based on a combination of hydrochloric acid and hydrogen peroxide to dissolve the valuable metal fraction which can be precipitated afterwards.INTRODUCTIONPlatinum and the corresponding metals from the PGM group, especially palladium and rhodium are well known as catalytic active materials. They support chemical reactions which are inhibited. This effect is used to decrease the amount of harmful compounds like hydrocarbons, carbon monoxide or nitrogen oxides in automotive exhaust gases. The generation of these toxic substances is based on incomplete combustion, which in turn is caused by non-ideal conditions in the combustion chamber. Catalytic converters minimize the harmful compounds by supporting the following Reactions 1 – 3 (Votsmeier et al., 2009).CO + ½ O2 ? CO2 (1)CnHm + (n + ¼ m) O2 ? n CO2 + ½ m H2O (2)2 NO + 2 CO ? N2 + 2 CO2 (3)Platinum and palladium are very effective for the oxidation (Reactions 1 and 2), while rhodium supports the decomposition of nitrogen oxides by carbon monoxide (Votsmeier et al., 2009). The classical three way catalyst was a platinum – rhodium combination with a Pt:Rh ratio of 5:1 (Hagelüken et al., 2005). Today the platinum, palladium and rhodium ratio is highly variable and strongly depends on the engine type as well as on the car producer. Diesel engines are operated with a super stoichiometric air addition in comparison to spark ignition systems. Therefore the exhaust gas composition and off gas temperature is different. Based on the high oxygen amount, diesel engines produce less carbon monoxide and hydrocarbons but more nitrogen oxide in contrast to gasoline engines. This leads to various requirements for the catalytic converters."

Jan 1, 2012

By Henri-Louis Jacob

Le Québec dispose de ressources en silice abondantes et diversifiées, pouvant convenir dans l'ensemble à la plupart des usages industriels. Dans les terrains Paléozoïques des BassesTerres du Saint-Laurent et des Appalaches, les ressources identifiées comprennent les grès quartzitiques purs du Croupe de Potsdam (Cambrien), exploités notamment à Saint Canut au nord de Montréal comme source de sable de silice pour l'industrie du verre; les arénites quartzitiques des Formations de Val-Brillant (Silurien moyen) et de Kamouraska (Ordovocien inférieur) exploitées dans l'est du Québec comme source de fondant métallurgique; les grès friables de la Formation de Guigues (Ordovicien) au Témiscamingue, à partir desquels on produit des sables de silice utilisés notamment en fonderie et en filtration. Dans la province structurale du Grenville, au nord du fleuve Saint-Laurent, les métaquartzites purs du Supergroupe de Grenville représentent une source importante de silice pour la production de silicium, de ferro-silicium et de carbure de silicium. Des veines et amas de quartz ont aussi été exploités un peu partout au Québec comme source de fondant métallurgique ou de silice ultra-pure pour la production de silicium métal. Quelques dépôts de sables naturels, généralement d'origine marine ou deltaïque sont finalement exploités dans la région de Montréal comme source de sable pour des usages n'exigeant pas un produit de haute pureté.

Jan 1, 2001

By George Delorme

"AbstractThe basic intention of this paper is to present, from a practical viewpoint, a thorough outline of all the sound and accepted principles connected with attaining satisfactory rope performance from multi-rope friction winders.In order to emphasize the importance of some aspects of rope maintenance, a limited amount of hoist rope theory has been included, a s it is felt that without this, some of the more critical, but nevertheless practical, aspects would perhaps pass without full appreciation of their individual merit.It is very much appreciated that many of the maintenance topics and practices discussed herein are already being observed with a high degree of skill among those already involved in modern friction winding. The hope is expressed, however, that the paper will be of additional assistance, and of particular help in introducing sound maintenance principles to those who are moving into this field of operation for the first time.Hoist RopesWITH a multi-rope friction winder system, structural upset within the hoist rope's cross section can occur if the ropes slip in the drum treads. This upset will usually appear at either end of the rope at the tangent point of the drum or deflection sheave with the respective conveyance in the normal uppermost position. This slipping action on the drum causes the outer cover of a Full Locked Coil or the strands of a stranded rope to shift, leading to structural upset. The result very often means that the ropes have to be withdrawn from service before completing their maximum service potential.The cause of any rope slipping in its tread can be associated with a discrepancy in tension of that rope between one side of the drum and the other."

Jan 1, 1977

By R. A. Price

The base of the biozone of Olenellus is accepted as the most universally applicable criterion for defining the base of the Cambrian System. The use of this definitive criterion is restricted by important practical considerations. In the southeastern Canadian Cordillera this zone appears to truncate the basal ortho-quartzite of a west to east marine -transgression. This transgression began in Interior British Columbia in the Late Proterozoic and terminated in the region of the present Rockies in the Late Waucobian. Most of the material deposited by the transgressing sea originated in the eastern positive element 'Laurentia' and was transported over the intervening low Proterozoic-Windermere erosion surface. The configuration of the advancing shoreline and the distribution of the sediments were controlled by the tectonic activity of positive elements in northwestern Montana (Montania) and in the Fairmont Hot Springs-Radium area of British Columbia.

Jan 1, 1956

By J. P. Sims

Abstract - Ultramafic to mafic igneous intrusions of the Las Aguilas district form part of a belt of generally mafic plutonic bodies within medium- and high-grade early Paleozoic metamorphic rocks in the southern Sierras Pampeanas region, Province of San Luis. The intrusions host the largest known nickel sulfide resource in Argentina and contain significant Cu, Co and PGE mineralization (2.2 Mt at 0.5% Ni, 0.5% Cu, 0.035% Co). Sulfides at Las Aguilas Este, one of two principal mineralized zones, are hosted by a body comprising subvertically dipping units of predominantly orthopyroxenite and melanorite cumulate, with lesser dunite, harzburgite, norite, leuconorite, and amphibolite. The units are zoned horizontally from ultramafic to mafic compositions, representing primary magmatic zonation away from an original base or side of the intrusion. Intercumulus nettextured and disseminated aggregates of pyrrhotite-chalcopyrite-pentlandite are concentrated in the peridotitic zones and extend into melanorite. Whole rock major and trace element compositions, and olivine chemistry, indicate that the parent magma was gabbroic/basaltic with 100 (Mg/Mg+Fe) near 59, and resembles tholeiitic magmas generated in subduction-related arc, or back-arc settings. Unusually aluminous Cr-bearing spinel is compositionally similar to those in some synorogenic mafic/ultramafic plutons in magmatic arc settings. Relatively Ni-depleted olivines and low Cu/Pd ratios are indicative of magmatic sulfide segregation early in the crystallization of the magma. Early orthopyroxene saturation and virtual lack of clinopyroxene, in conjunction with sulfur isotope values up to +6.6 ‰, spinel compositions, and presence of graphite, phlogopite and magmatic hornblende, all attest to probable crustal contamination of the parent magma. Assimilation of crustal sulfur may have been crucial in the early attainment of sulfide saturation and resultant formation of magmatic Ni-Cu sulfide mineralization. Fabrics, textures and mineralogy of the intrusions and country rocks and U-Pb zircon dating indicate syntectonic-synmetamorphic emplacement at 478±6 Ma during the Famatinian (Ordovician) orogeny. Minor to locally significant recrystallization and deformation of mafic-ultramafic rocks and redistribution of sulfides and PGE occurred during and following the Famatinian orogeny. The Las Aguilas intrusion is one of several tholeiitic mafic-ultramafic intrusive complexes within an Ordovician arc - back-arc system in the Sierras Pampeanas. Aeromagnetic datasets and regional mapping suggest there is further potential for intrusion-hosted Ni-Cu mineralization along this eroded magmatic arc.

Jan 1, 1999

By G. Mousavian, R. Bagheri, N. Dalili

Polypropylene (PP) and its composites have an increasing use in automobile and domestic industries. Since the published results on strain rate effect on yield behavior do not match, and there is a high attention paid for effect of nanometeric fillers on deformation behavior of composites, in this research the strain rate effect on yield behavior of PP and the effect of nanometeric fillers on deformation behavior of PP have been studied. Microscopic observations and tensile tests in different strain rates on neat PP samples and on samples filled with 5, 10 and 15 %wt have been used. A dramatic change in behavior for the modulus and post-yield slope curves when the strain rate is between 0.0433-0.05 s-1 has been observed. Microscopic observations on PP indicate a change in deformation mechanism from shear yield to crazing at the same strain rate that the change in behavior of curves occurs. It has been observed that in PP nanocomposites with higher amount of calcium carbonate, fracture in early stages of deformation occurs in lower strain rates. In other words for a fixed stain rate there is a critical filler percentage such that if the filler percentage is higher then early-stage fracture will occur. Similarly for a fixed filler percentage there is a critical strain rate and in higher strain rates early fracture will occur. The critical stain rate will decrease as the filler percentage increases and vice versa.

Jan 1, 2006

By Zhang. L.

Ordered intermetallic PtSb had been synthesized by arc-melted and then sintering treatment. The electro-oxidation of formic acid on PtSb was investigated at room temperature by cyclic voltammetry and chronoamperometry. The results are compared to those at a polycrystalline platinum electrode surface. It was found that PtSb intermetallic was catalytically more active than pure platinum according to the onset potential and current density. XRD and XPS technologies had been used to investigate the crystal structure and electron effect. We think formic acid decomposition on PtSb favors the reactive intermediate route and is not very much affected by the CO intermediate as compared to Pt.

Jan 1, 2005

By M. L. Jeremic

Altered and unaltered coal from the Star-Key Mine near Edmonton, Alberta has been tested under compression and under tension. The test results showed that altered coal samples have an appreciably lower strength than unaltered coal. Altered coal samples do not give a linear load-displacement curve, peak strengths are poorly defined and yielding is observed over a range of loads, so the material can be regarded as relatively plastic. However, unaltered coal samples produce a linear loading curve with a high tangential modulus and an easily distinguished peak strength at which there is a sudden brittle failure. These findings lead to important differences in the theoretical design of ribs and pillars in underground mines in the two coal types. The substantial differences in the strength properties and behaviour of the two types of coal are governed by a higher intensity of cracks in the weathered coal. Two causes of the additional cracking can be suggested-subaerial weathering and subterranean weathering of the coal.

Jan 1, 1979

By T. Boyd, K. McTaggart, J. Qiu

"Hudbay Minerals’ Flin Flon process plant produces a copper concentrate and zinc concentrate from the three ores it processes: 777, Reed and Lalor. Unlike many Cu-Zn ores, the average Zn: Cu ratio in feed is around 2:1, whereas, in many Cu-Zn separation plants the Zn: Cu feed grade is substantially higher than 2:1. The lower Zn: Cu in plant feed is a challenge for limiting Zn recovery to the Cu concentrate. While total recoveries of Cu and Zn at Flin Flon are very good; selectivity is the key challenge and small changes in ore or plant, can result in quite variable Zn recovery to Cu concentrate, and accordingly, Zn recovery to Zn concentrate. Magnetic conditioning has been shown to be selective between the two paramagnetic minerals chalcopyrite and sphalerite. Statistical testing of magnetic conditioning was undertaken at Flin Flon with the objective of increasing Cu recovery to Cu concentrate without increasing the Zn recovery to Cu concentrate - in effect increasing Cu-Zn selectivity. This has been achieved elsewhere with magnetic conditioning with the probable mechanism being an increase in fine chalcopyrite recovery, and a reduction in entrained, ultrafine, non-activated sphalerite to Cu concentrate. The results did indeed show an increase in Cu recovery to Cu concentrate of 0.8% to high confidence, but the decrease in Zn recovery to Cu concentrate was not to high confidence. This is effectively an increase in Cu: Zn selectivity in the Cu circuit – higher Cu recovery with no change in Zn recovery. However, while there was an increase of 1% in Zn recovery to Zn concentrate with magnetic conditioning, the variability in this parameter meant that this increase, though larger in magnitude than the Cu result, was not to high confidence."

Jan 1, 2019

In the last five years, new iron ore pellet plants have been built with significantly reduced air pollution levels compared to the older generation of plants. European and American pollution controls are more stringent that in China and Brazil. The recent American plants have successfully employed circulating fluidized beds for sulfur control, baghouses for particulate control, activated carbon injection for mercury and a new design of specialized low-NOx burners.

Jan 1, 2015

By Joseph J. Larry

In hard siliceous sandstone strata overlying coal seams, roof bolting is often the bottleneck in the coal production cycle. In the past, these strata have been drilled by pneumatically operated stopers. Although slow drilling is cumbersome and uncomfortably noisy, the stoper was the most effective drill in these harder strata. However, because of the (U.S.) Coal Mining Safety Act, which limits noise levels for operating drills, FMC Mining Equipment developed the water-through-the-drill-steel method of drilling high-compressive-strength strata. Although water-through-the-drill steel had been developed earlier, the real impact of wet drilling techniques surfaced when the dual-boom roof drilling machines were installed at the Virginia-Pocahontas Division, Keen Mountain, Virginia, in 1974. This paper covers some of the technical details of the water-through- the-drill-steel design and its application.

Jan 1, 1979

By S. Xu

Magnesium alloy AM50 is of interest to automotive cradle application because of it excellent castability and good ductility. In this work, microstructure and mechanical properties of both low pressure die cast (LPDC) and high pressure die cast (HPDC) AM50 test bars are characterized. Microstructure was examined using optical microscope, scanning electron microscope (SEM) and transmission electron microscope (TEM). Phase identifications were performed using energy dispersive x-ray spectrometer (EDS) and TEM diffraction. It has been found that LPDC produces much coarser microstructure than HPDC. At the same time, the HPDC samples are more heterogeneous in microstructure and composition close to grain boundaries. Particles with various dimensions and morphologies of two different intermetallic phases, Mg17A112 and A18Mn5, were found in all the samples. Mechanical tests were performed under conditions similar to those related to an engine cradle application. LPDC samples show lower strength but better creep resistance than HPDC mainly due to the difference in grain sizes and grain boundary microstructure between LPDC and HPDC. Creep curves are well described by the empirical Andrade equation. Tensile-compressive yield and creep asymmetries were found in AM50, i.e. better deformation resistance in tension than in compression. The average yield asymmetry ratio for all the samples is 0.87. Microstructural examinations on the samples tested in tension, compression and creep showed that the deformation mechanisms in AM50 were slip plus twining at temperatures up to 125°C. The examinations indicate the important role of twining in the asymmetry phenomenon. The creep results indicate that dynamic precipitation of the Mg17A112 phase during testing is not the mechanism directly responsible for the creep asymmetry in AM50.

Jan 1, 2004

By D. Pérez Escobar

Multiphase steels are quite sensitive to hydrogen embrittlement. Laboratory tests to evaluate this often use electrochemical, charging to introduce hydrogen into the sample, but damage purely caused by hydrogen charging has to be avoided. A ferrite-bainite steel, was charged using various conditions to identify when surface blisters occurred. Samples were also checked for internal, damage by electron microscopy. This study was repeated for three other multiphase steels and pure iron. An HSLA steel, was found to be more resistant whereas pure iron was quite susceptible to internal, hydrogen damage. For al, industrial, steels, cracks concentrated in the middle of the sample were attributed to inclusions and segregations, inherent to production.

Jan 1, 2010

By G. M. Carr-Harris

"THE SUBJECT of permanent molding has received a great deal of attention in the technical press as illustrated by the many excellent articles in the bibliography which follows. In general, this covers the period 1940-1958 and is merely representative of what is available. Numbers in •brackets refer to items in the bibliography.It may be desirable at the outset to give a few definitions covering those terms directly related to this subject. The following is a definition of permanent-mold casting as given by J. W. Meier in a paper, ""The Non-Ferrous Metals and Alloys"", read before the Ottawa Valley Chapt.er of the American Society for Metals:""Permanent Mold Casting is used where a large number of castings of the same part are required and higher mechanical properties, greater density and closer tolerances are essential. Since metallic mold s are very expensive, the number of castings must be sufficient to, defray, at least partially, the added expense. Molds are usually made from a good quality cast iron, 1but other mold materials, such as the aluminum and copper alloys, graphite, ceramics, etc., are being used in certain cases. Important factors in permanent mold casting are the mold temperature; the proper mold dressing; and, as in all other casting methods, the mold geometry, that is to say, the design of spruces, gates, risers and vents""."

Jan 1, 1960