Search Documents

By Simon C. Dominy, Alwyn E. Annels, Paul Wheeler, Suzanne P. Barr, G. Simon Camm

Narrow veins are an important world-wide source of silver, tin, uranium and particularly gold. To potential ?nanciers, this style of mineralization is viewed as high risk because of the often relatively small resource involved and high cost of estimation. In many cases diamond core drilling will not enable resource estimation beyond the inferred and indicated categories. Exploratory under-ground development is required to de?ne measured resources. The de?nition of geological and grade continuity are major factors in narrow vein assessment. A measured resource must be based on strong geological and grade continuities. Narrow veins, generally less than 3 m wide, are complex geological phenomena, which commonly display unpredictable geometry and grade distribution. Variations in structural continuity, dip, strike, width, mineralogy and speci?c gravity are common. Veins may be composite, with ore-grade mineralization restricted to a speci?c structural domain. Branches, intersections and braided zones are common features. Potentially high-grade zones are often localized within ore shoots, which are surrounded by barren/low-grade regions. Resources must be determined as closely as possible to reality and re?ect the distribution of the commodity in the rock. Estimation has three main requirements: (1) geological study to determine orebody nature;(2) estimation of tonnage and grade, and (3) the presentation of this information using a classi?cation that is clear, unambiguous and bankable. Estimation methods employed are either classical or geostatistical; however, classical methods are often used because of the dif?culties in applying geo-statistics. Grades generally show a strong positively skewed distribution testifying the presence of high-grade values. Problems exist in the applicability of cutting outlier values risking over- or under-estimation of grade. It is generally believed that where resource estimates are in error, poor geological control is usually the cause. Overestimation can lead to the closure of a mine through lost revenue and capital. An understated estimate can result in an opportunity missed for pro?t and/or greater economies of scale. De?nition of reserves involves the consideration of economic and engineering data, to decide which part of the resource is economically mineable. Geology plays a similarly important role at this stage in the assessment of likely mining method, dilution, recovery etc. Throughout resource/reserve estimation, it is crucial that the amount and quality of the data and the geologist’s experience are relevant. The impact of geological understanding on estimation is often undervalued or assumed to be of lesser importance than ?nding grades and tonnages. This paper discusses the geology of narrow vein deposits and the importance of geology in their evaluation.

Jan 1, 1997

By H. J. Burchell

"IntroductionTHE PURPOSE of this paper is to introduce the reader to rock bolting and its present application in mining.Rock bolting consists of bolting insecure rock to secure rock in order to form a safe structure. The insecure rock may be a weak beam or loose from arching or from sloughing. The material is strengthened and held in place before damage can result.Little is known of the limitations of rock bolting; to date, work has been carried on by trial-and-error, with large safety factors being used. Rock bolts have been principally used for roof support. Bolting offers a new field of support to the mining industry: it now has a permanent position as a ground control method.HistoryRock bolting is a relatively new means of support, its exact origin being unknown.Bolting has been in use at the St. Joseph Lead Company's property in Southeastern Missouri for the past twenty-six years, the first attempts having been hit-or-miss trials before a systematic attack was made. Many instances of occasional use of rock bolts have come to light .in widely separated mining camps, .some dating back forty years.The first installations were made as supplements to wooden timbering where space was restricted. The excessive costs compared to wooden timbering hindered their advancement for a number of years"

Jan 1, 1955

In order to avoid impurity problem and enhance absorption/desorption kinetics of Mg-based compounds, nanostructured Mg-based compounds were synthesized from Mg, Ni and other elemental nanoparticles produced by hydrogen plasma-metal reaction. XRD and TEM results demonstrate that homogeneous nanostructured Mg-based compounds with less impurity were successfully synthesized by this method. DSC in hydrogen atmosphere, pressure-composition isotherm and the kinetics of hydrogen adsorption/desorption were investigated at different temperatures. The results show that the nanostructured Mg-based compounds can absorb hydrogen in a high speed at a low temperature.

Jan 1, 2005

By A. Warczok

The mechanisms and kinetics of copper oxidation and reduction have been investigated in small scale thermal gravimetric experiments as well as in laboratory pilot scale, packed bed reactors. With blister copper flowing gravitationally down through a packed bed of ceramic particles, counter-current to low oxygen containing combustion gases, the rate of oxidation was found to be very high due to the large surface area created. Similarly, reduction by flowing copper through a packed bed of charcoal lead to rapid de-oxidation. Based on these laboratory measurements, fundamental rate data have been obtained. Modeling of industrial sized packed bed reactors using the laboratory results, opened up the possibilities of developing a new, very intensive, continuous process for copper fire refining. The developed mathematical model together with a computer process simulator, allowed for the design of the industrial-pilot installation to be built and tested at the ENAMI Paipote smelter in Chile.

Jan 1, 2007

By E. J. Marcotte

"IntroductionDevelopments in the preparation, hydraulic transportation and placement of classified mill tailing as an effective backfill and support for mining excavations, have made feasible several advancements in mining methods that are safer and more economical. Hydraulic backfill systems have played an integral part in the development of more efficient cut-and-fill and blasthole stoping.The hydraulic transportation of tailing fill has made possible the elimination of expensive and laborious transportation, placement and spreading of gravel type fills. Also, in cut-andfill stopes, the use of hydraulically placed consolidated fill has largely eliminated the need to use extensive timbering for floors and supports, previously necessary when only gravel type, waste rock or unconsolidated tailing fill was used .Another important advantage of using mill tailing as backfill is that it decreases the need to contain a large portion of the mill solids waste in a surface disposal area and thus reduces environmental and ecological problems.Tailing Fill PropertiesConsolidated tailing fill consists of deslimed mill tailing and Portland cement. These two materials are mixed together in various proportions to form a high density slurry which is transferred underground by gravity through boreholes and pipelines. After placement underground, the water is drained off and the mixture is allowed to set. The strength of the consolidated fill is dependent on the cement content, particle size distribution and curing time. A typical tailing/ cement ratio used for bulk filling in stopes requiring vertical wall support is 30:1. Ratios ranging from 8:1 to 5: 1 are used for stope floors. High pulp densities minimize segregation and loss of cement during placement as well as reduce the amount of drainage water to be handled."

Jan 1, 1989

By John A. Hudson, Xia-Ting Feng, Joseph S. Y. Wang

Evolution over decades and progress over last five years have been made in many topics of interests to rock mechanics, geosciences, physics, and multi-disciplinary interactions in underground research laboratories and development facilities, as well as in underground energy recoveries and environmental assessments. Rock mechanics and geotechnical engineering advances are associated with quantifications of disturbed/damaged zones and rock alternation and bursting processes and creation of underground spaces and accesses associated with deepening of shafts and lengthening of tunnels. Geophysics and earth sciences advances are associated with continuing collections of seismic, electromagnetic, and gravitational data and conducting various thermal, hydrological, mechanical, chemical, and biological investigations, both separately, simultaneously, and in different coupled ways. Astroparticle and underground physics advances are associated with many long term experiments to detect rare events and needs for increasing larger and deeper halls to accommodate next generation detectors, shielings, and isolations. There are also increasing interesting in underground settings to explore multidisciplinary and inter-disciplinary sciences and technologies. Energy and environmental sciences and assessments have evolved from traditional oil and gas focuses to recent activities associated with green resources and alternative recovery/disposal strategies. The evolution and progress of these interdependent and related fields are discussed in this quadrennial Congress.

Jan 1, 2015

By Roger J. Goodman, Don Riva

"IntroductionCrows Nest Resources Limited (CNRL), a wholly-owned subsidiary of Shell Canada Resources Limited, is nearing completion of its first coal project, located in southeastern British Columbia. CNRL shipped over 700,000 tonnes of thermal coal to foreign markets in 1982. With the completion of the metallurgical coal plant in December, 1982, shipments of both thermal and metallurgical coal will increase substantially in 1983 and will approach the anticipated operating capacity of 3.0 million tonnes in 1985. The Line Creek Mine lies some 25 kilometres north of Sparwood in southeast British Columbia (Fig. 1). The open-pit mine is located on top of Line Creek Ridge, with coal being hauled 16 km to the thermal and metallurgical coal preparation plants, situated adjacent to the already existing Canadian Pacific Railway. Most of the coal is moved by 108 car unit trains by CP Rail to coal ports in Vancouver, where it is loaded onto vessels destined for overseas markets. Some smaller scale car load shipments are moved by rail to contiguous markets in the Pacific Northwest. History The southeastern British Columbia area, known as the East Kootenays, is steeped in a rich coal mining heritage, dating back to the latter part of the nineteenth century. Predecessors of Crows Nest Resources Limited were instrumental in developing the rich coal reserves in the area. In 1887, William Fernie, a pioneer-cum-prospector recognized the potential of coal deposits in the East Kootenays. Spurred by the relentless push west of the Canadian Pacific Railway through the Crows Nest Pass area, Fernie recognized that it was just a matter of time before the steam locomotives provided him with his required market. That time arrived in 1897 when Fernie helped to form the Crows Nest Pass Coal Company and coal mining commenced at Coal Creek, near his namesake town of Fernie. During its almost 70-year history, this company produced over 48 million tonnes of steam coal and 8 million tonnes of coking coal. In 1965, the Crows Nest Pass Coal Company was re-named Crows Nest Industries, to better reflect its expanded interests into forest products, and it is the latter company which Shell Canada Resources Limited acquired in 1978. The extensive coal resources of Shell, in both Alberta and British Columbia, were rationalized into one group with the birth of Crows Nest Resources Limited to manage and develop the coal holdings."

Jan 1, 1985

By Jean-François Dorion

In an underground mine rock reinforcement elements and surface support units are often exposed to conditions that make them susceptible to corrosion. These unfavourable conditions include high relative humidity, the presence of dust and various other particles in the atmosphere, splashing of water and gases from blasting and diesel equipment. The corrosion of support systems is often associated with a loss in capacity that can be a major safety and economic concern in underground mines. A support system is composed of several components such as bolts, mesh, plate, retaining nut, cable ties. Every individual component can deteriorate due to atmospheric or aqueous corrosion and consequently can damage the integrity of the support system. This paper reports the results of a 5-yr study on the loss in capacity of individual support and reinforcement components at selected underground hard rock mines. As part of this investigation corrosion coupons were installed at selected locations at participating mines. A number of these coupons were recovered at regular time intervals and analysed for any signs of corrosion and subsequently tested to quantify any loss in capacity. The testing of the corrosion coupons was complemented by similar tests on recovered mesh and friction bolt specimens from the site. The collected data have provided useful insights on the factors that contribute to the corrosion of support systems. This knowledge can aid in the selection of appropriate support strategies and a reliable assessment of the predicted useful life of a support system and the need for rehabilitation.

Jun 1, 2012

By E. E. Cudby

"FOLLOWING the Leduc discovery •by Imperial Oil in 1947, The California Standard Company began to acquire land in the area immediately west of Edmonton and in line with the Leduc reef trend (Figure 1).The California Standard Winter-burn Province No. 1 in Lsd. 10, Section 4, Township 53, Range 25, West 4th, which was spudded, on the basis of a seismic anomaly, in December, 1949, failed to find reef. This well was located on the eastern .edge of a large land block which California Standard and Imperial Oil had pooled as a joint venture, with California Standard a:s the operator (Figure 2).The culmination •of an extensive exploration and land aquisition programme was the drilling of the California Standard-Acheson Province No. 1 well .in Lsd. 13, Section 2, Township 53, Range 26, West 4th. On August 24th, 1950, a drill stem test was run in the D-3 zone which had been encountered at 4,969 feet, and a flow rate of 702 barrels per day •of 36° gravity oil was obtained. Just previously, Imperial Oil had completed a similar programme in the Stony Plain Reserve with the swabbing-in of Imperial Stony Plain No. 1. These two discoveries set off a drilling programme to determine the extent and value of the oil accumulation.Subsequent drilling of wells some successful .and others not by several other companies as well as California Standard bias, .to date, still left much to be determined as to the approximate delineation of the productive limits of the Ache-son-Stony Plain area. However, to August 31st, 1951, there were twenty-one D-3 producers north of the reserve and three in the Stony Plain Reserve."

Jan 1, 1952

By Leiting Yue, Peng Ren, Yu Shen, Zhihong Liu, Haibao Shao, Longgong Xia, Feng Yu

The Kennecott-Outotec Flash Converting technology has been proven as an advanced and mature process in 5 individual plants during the past 2 decades. High grade copper matte (65–72%) produced in the flash smelting, or other smelting technologies is granulated to 3-5mm granules in a water torrent, and further crushed to fine powder (≈50µm) and dried to contain less than 0.3% H2O. Oxygen enriched air, together with fine copper matte powder and lime flux are injected into the reaction shaft by a matte burner. The copper making and slag making reactions will happen in very short time and distance during the particle falling and settling. However, industrial practice has found negative effects caused by sodium contamination. Na is introduced in the copper matte granulating process, and appears as Na2SO4 on particle surface. When Na content was high, scaling problems in the boiler will be worse, and the processing air will be blocked by the growing accretion around the matte burner, and as-produced blister copper is always high in S and O. In this present study, an industrial matte sample was used in the experimental work. Na was introduced into the matte powder by Na2SO4 solution soaking. The burning behaviour of the doped copper matte powder has been investigated as a function of the impurity concentration and processing temperature. Morphology and composition of these samples explained how Na2SO4 converts and reacts in the oxidizing atmosphere, and how they or their converting species influence the burning behaviour of matte particles. Cross-sections of as-prepared samples were analyzed with SEM-EDS, and the reaction mechanism has been carefully interpreted. Results from the present study can benefit both academic and industrial people. INTRODUCTION "Flash Converting" technology was developed jointly by Kennecott Utah Copper Smelter and Outotec (Finland) OY in 1992. The first industrialization of the technology was in Utah Smelter in 1995. Since 2006, it has been successfully applied in Xiangguang Copper, Tongling Jinguan Copper Branch, Fangchengang Jinchuan Copper, and Ningde Southeast Copper. The technology has also been further developed in those smelters. At present, roughly 2 million tons blister copper is produced annually through the Kennecott-Outotec Flash Converting technology, accounting for more than 10% of global primary copper production. The technology has advantages of high efficiency, high sulfur capture rate, good in environmental issues, mature equipment supporting, high automatic control level, low comprehensive energy consumption and flexible connection with the smelting unit, which make the technology to be one of the best choices in investing a new large-scale copper smelter or updating an old copper project in the world.

Jan 1, 2019

By T. Abu Leil

A new class of ternary Mg-Sn-Ca alloys is being developed to address the dual demands of corrosion and creep resistance at service temperatures. While tin has proven to enhance the corrosion resistance, calcium is expected to significantly increase their creep resistance of binary magnesium alloys. Their effects in ternary magnesium alloys are not yet known. The series of alloys studied has Sn and Ca in the ranges 3-6% and 1¬2%, respectively. The results indicate that these alloys have two-phase structures with CaMgSn phase dispersed in a matrix that is predominantly a solid solution of magnesium. The corrosion behavior of these alloys has been investigated by means of salt spray tests and potentio-dynamic measurements. Creep behavior of these alloys was measured at a temperature of 135 C under an applied compressive stress of 85 MPa. Scanning Electron Microscopy with Energy Dispersive X-ray facility and X-ray Diffraction techniques were used to characterize the microstructures. The results indicate the prospect of designing alloys that can provide optimum combinations of corrosion and creep resistance by adjusting the relative compositions of Sn and Ca in the system.

Jan 1, 2006

By G. G. W. Thom, A. A. F. Schuldt

At The Steel Company of Canada, Limited, iron oxide dust from the basic oxygen open hearths is being collected by means of electrostatic precipitators. The utilization of this dust, which has been hampered by the presence of zinc and lead oxides and sulphur compounds, is made possible by direct reduction in a rotary kiln. The description of the dust collection system and the results of kiln tests are presented.

Jan 1, 1966

By K. van Warmerdam, M. Pearson, C. Kember, D. McMullen, M. Thayer, C. Ugarenko

In July 2012, Hatch Ltd. and Air Products & Chemicals Inc. completed construction and commissioning of a 4000 tpd O2 cryogenic air separation unit (ASU) for Barrick Gold’s Pueblo Viejo Project located in central Dominican Republic. The ASU produces high pressure gaseous oxygen, which is used for the oxidation of refractory sulphide ore within the pressure oxidation (POX) circuit. As a result of the project’s remote location and tropical climate, many challenges were faced over the course of construction, commissioning and start-up of the ASU. These challenges included adequate preservation of equipment due to dusty and humid site conditions, final assembly and erection of the cryogenic distillation columns on site, limited spare parts inventory/availability, and an unfinished power source for plant commissioning. This paper discusses the steps taken by Hatch and Air Products to successfully design, construct, commission and start up the largest stand-alone ASU plant for a POX application in the metallurgical industry.

Jan 1, 2014

By C. Van Den Heuvel, C. B. Van Buuren

BIOX® has been successfully demonstrated over the past 2 decades for the recovery of gold from refractory sulphide concentrates. To date 12 successful BIOX® plants have been installed in 8 countries spanning 4 continents with the 13th installation currently nearing completion in the Philippines. In 2010 BIOMIN introduced the ASTER™ process for improved water balances in commercial BIOX® applications by supporting tightening environmental legislation on water usage and availability in both arid and tropical regions. Previously, a common challenge for BIOX® plants was the inability to recycle thiocyanate containing water due to the low tolerance of the organisms. ASTER™, a biological thiocyanate and cyanide destruction process, renders a non-toxic solution for re-use in BIOX®. Two commercial ASTER™ plants are in operation with the 3rd ASTER™ plant under construction in the Philippines. A 3rd BIOMIN technology, specifically developed for double refractory ores is available for implementation. The HiTeCC process has shown considerable success on ores where competition from disseminated carbon has rendered ineffective gold recoveries. Through HiTeCC, gold is desorbed from the carbonaceous matter by manipulating the ionic strength and temperature of conventionally treated CIL product. One Australian commercial plant utilises HiTeCC while a 2nd installation is set for commissioning 4th Quarter 2014. BIOMIN’s premier solutions for refractory gold processing are described herein.

Jan 1, 2014

By J. Paraszczak

ABSTRACT Diesel-powered loaders are a pillar of modern underground metal mining. As these mines are getting deeper and hotter and the emission regulations stricter, ventilation costs are soaring, affecting production cost. Also, the cost of diesel fuel is expected to rise. These may make the use of diesel engines more problematic. Electric load-haul-dump machines (LHDs) are an interesting alternative. This paper compares features and performance of diesel and electric, cable-powered LHDs. It overviews equipment offerings, and compares, analyzes and discusses technical parameters, operational problems and cost issues. The paper gives some conclusions about electric LHD applicability and performance, indicates possible applications, and suggests further research work.

Jan 1, 2013

By Enzo Palumbo, Joël P. T. Kapusta, François Larouche

In light of the rapid deployment of bottom blowing smelting in China over the last ten years, one has to wonder why it has taken the copper industry so long to adopt ultra-high oxygen enrichment via Savard-Lee type injectors. As early as 1976, Kellogg and Henderson suggested, in their landmark paper on energy usage in the copper industry, that ‘maximum use of oxygen enrichment of process air’ was one of seven ‘energy saving features’ for copper matte smelting and converting. Yet today, shrouded injection and high oxygen enrichment has not been implemented in copper bath smelting outside China and Vietnam. In this paper, the authors explore the reasons why bath smelting processes such as the Noranda Reactor and the Teniente Converter still operate around 40% oxygen enrichment, while the bottom blowing SKS/BBS process typically runs at 65 to 75% oxygen, with all three processes producing white metal. Are there fundamental metallurgical explanations for this striking difference beyond the long-standing skepticism towards high oxygen shrouded injection and its perceived high implementation cost?

Jan 1, 2015

By Lars A. Bergstrom

High-voltage direct -current transmission is a relatively new technology. The successful development and operation of AC/DC converters, capable of handling large power blocks, have made HVDC transmission generally accepted by utility engineer s and planners around the world. HVDC technology still has significant development potential and, as a result, it is expected that equipment costs will escalate at a substantially slower rate than those of conventional AC equipment. This development will also result in still more compact terminal stations. This paper reviews two modern HVDC installations. In Zaire in Africa. a 1700-km overhead DC line rated at 500 kv, will supply power to the copper mining district in the Shaba region. Another HVDC link connects Norway and Denmark through a submarine cable rated at 250 kv. This is the longest HVDC cable in the world, 127 km, and the water depth , maximum 530 m, is also much greater than for any previous similar cable. The reasons for selecting HVDC are discussed, and the design and layouts are presented.

Jan 1, 1978

By C. A. Hardie, G. F. Leichtle, J. A. Finch, J. A. Watson

"The recycling of wastepaper has become an important and common process worldwide. Techniques similar to those used in the mineral processing industry are used to produce high quality recycled fibres for use in newsprint. The mineral processing group at McGill University, in conjunction with the Pulp and Paper industry (Mechanical and Chemi-mechanical Wood Pulp Network), has adapted one of these techniques, column flotation, for the purpose of deinking wastepaper. This article describes the typical process of recycling wastepaper from a mineral processing point of view. It also presents results from McGill University’s flotation column test work at a Québec wastepaper recycling facility. IntroductionThe recycling of wastepaper has become an important and common process worldwide, including Canada which is now the world’s largest importer of wastepaper (CPPA, 1996). Much of the current drive to increase the utilization rate of recovered paper is a reaction to the solid-waste disposal problem that faces many Canadian and United States municipalities. The real problem in the disposal of solid waste is not the absolute amount of garbage that must be disposed of each year, but this amount in relation to available disposal capacity.Environmental restrictions on the creation of new landfill sites and incinerators (the two main options for disposal of municipal solid waste) have tightened the demand/supply balance in the solid waste disposal market. This shrinking availability of waste disposal sites in the face of increasing population with greater disposal requirements defines the Developed World’s solid waste crisis. Not only are there fewer disposal sites available, but the costs of using them is skyrocketing. These factors have increased government regulations mandating recycled paper content in newsprint. Conservation and environmental issues make the current drive for wastepaper recycling a real issue and business opportunity."

Jan 1, 1999

By Iain G. Bruce

The need to improve supply reliability while improving our environmental record during the past half decade of low metal prices has required the mining industry to prioritise expenditures. Quantitative Risk Assessments using third party reviewers and specialist risk management teams have assisted in identifying hazards that can both disrupt supply and impact the receiving environment. Graphical displays using risk ellipses can simplify the presentation of the results in a Probability-Consequence (PC) graph. Development of risk acceptability envelopes using readily available financial data superimposed onto the same PC space assists management to prioritise their risks and focus on risk reduction measures. Development of this system and examples of the successful implementation of the system from several recent projects are described.

May 1, 2003

By Bird. M.

As the Cadia mill was the first 40ft diameter SAG mill, commissioned in 1998, its performance, liner and discharge design attracted considerable international attention. Twelve years on, the liner design and the control philosophy are being readdressed to further improve the mill?s performance. A comprehensive series of 3D liner scans, over life of the liner, have been used to calibrate liner mass loss and progressive changes in the liner profile. This data is being used to provide true charge mass and mill filling, plus progressive trajectory profiles over life of liner. This information, along with measures of mill performance over liner life, is being used to select the optimal operating conditions as the liner wears, and hopes to inform future liner design.

Jan 1, 2012