Search Documents

By N. Sarmady, Mei Li, N. C. Parson, W. J. Poole

"The mechanical behaviour of AA6082 is a function of the extrusion conditions and in particular, the quench rate after extrusion. It is well known that precipitation of Mg-Si phases on grain boundaries during quenching can negatively affect the ductility of the alloy. In this study, AA6082 alloys containing 0.5 wt. % Mn and 0.15 wt. % Cr were direct chill (DC) cast, homogenized and then extruded to produce 3 mm x 42 mm strips. The microstructure in the as-extruded strips was unrecrystallized due to the Zener-Smith drag from the Mn/Cr dispersoids. It was shown that a solution treatment of 5 minutes at 560°C did not significantly affecting the as-extruded microstructure but if the as-extruded strip was cold rolled prior to heating, recrystallization occurred concurrently with the solution treatment. As such, 3 initial microstructures were produced, i.e. unrecrystallized and recrystallized with a grain size of 9 and 40 µm. After the solution treatment, controlled cooling experiments were conducted using the Gleeble 3500 thermomechanical simulator with cooling rates of 10, 25, 80°C/s as well as water quenched. The mechanical properties (e.g. yield stress, fracture stress and fracture strain) were determined from tensile tests for the different combinations of initial microstructure and cooling rate. The relationship between the quench rate and precipitation of Mg-Si phases on grain boundaries was examined by FEG-SEM. It was found that the yield stress decreased as the cooling rate decreased and that there was complex relationship between the fracture properties and the microstructure.INTRODUCTION As the automotive industry strives to reduce fuel consumption and CO2 emissions with the goal of reducing the environmental impact, there is a need for lighter vehicles. As a result, aluminum alloys are gaining popularity to replace steel parts as structural components. An exemplar of this is the Ford F-150 pickup truck which has an aluminum body and is ˜750 pounds lighter than the previous steel version of the vehicle. The structure includes a mix of aluminum sheet, extrusions and cast alloys. The current research is concerned with the performance of aluminum extrusions in applications such as side rails, crash tubes and other structural parts. These components experience a combination of bending, stretching and folding both during the forming of the part and in service, e.g. crash of a vehicle. There is a need to have detailed information on the influence of processing on final material performance, in particular the cooling rate after extrusion."

Jan 1, 2018

By Victor Azbe

Introduction Lime enters our daily life in many ways. Our building, chemical, agricultural, sanitary, and industrial endeavours depend on it to such a great extent that it could probably be called the most important inorganic chemical, and the extent to which it is used might be considered an index of industrial development. Industrial limes vary greatly in quality, due to internal structure and other characteristics. They may be good or bad, sensitive or slow to react. While improper manufacture may not greatly alter the appearance of the lime, it may affect its properties considerably and thus its suitability in the many processes in which lime is used. In some of the processes, one kind of lime is wanted, in others another. While the nature of the stone from which it is made has much to do with whether a lime is suitable or not, its burning and hydration are the crux of the matter. Up to not so many years ago, the knowledge of lime burning was rather imperfect and it is only relatively recently that its manufacture is approaching the state of a higher industrial art. This slow development was in part due to lime manufacture being scattered among many small concerns who, independently, either lacked the inclination or could not afford to strive for a higher technical development.

Jan 1, 1946

By C. T. Bischoff

Introduction Air conditioning is a term which has come into common use only during our generation. By definition, it means the positive and accurate control of temperature, humidity, movement, purity, and component constituents of the atmosphere within an enclosure. Claiming such results for Noranda's ventilation system, or for that of any other large mine, at present would be an idle boast. However, we are working toward that end with considerable success. Modern underground ventilation at Noranda dates back about six years. The later development of air conditioning is in its fourth season, but still in the experimental stage. Various ingenious methods have been devised to cool mines which, because of climatic or geological conditions or depth, are excessively warm. A few installations have been made to warm intake air during the winter months where this is necessary. However, the method currently in use at Noranda is unique in that it accomplishes both ends by one process. This method utilizes the freezing and melting of ice to equalize year-round temperatures. Mining Methods While a discussion of mining methods at Noranda is not proposed in this paper, a brief summary may be in order. The Horne mine of Noranda Mines, Limited, has been developed by six shafts, four of which are now active. The most recent, an internal shaft, extends to 6,000 feet below surface, but all of the ore mined to date has come from above the 3,000-foot level. Figure 1 shows a model of principal ore bodies. The area mined is relatively small in plan, considering its vertical extent and the tonnage per vertical foot. Most of the ore lies within an ellipse about 600 by 1,000 feet. While this has certain advantages, the mining of such massive orebodies has presented many problems.

Jan 1, 1947

By James Kear, Romain Prioul, Robert G. Jeffrey, Andrew P. Bunger, Dimitry Chuprakov

"Unconventional gas and geothermal reservoirs are typically naturally fractured and therefore the challenging problem of hydraulic fracture (HF) growth through naturally fractured rocks is an important issue especially for the development of accurate predictive HF models. This paper presents results from laboratory experiments in which HFs have been created in both sandstone and crystalline (gabbronorite) rock specimens such that they impinge either orthogonally or at an oblique angle on an unbonded, machined frictional interface. Depending on the conditions of each experiment, the fractures either cross or are blunted at the interface. The growth behavior was ascertained for these experiments based on a synthesis of the injection pressure record, active ultrasound monitoring, and direct post-experiment inspection of fractured specimens. From these experiments we observe: 1) A contrast between direct crossing and crossing with an offset for orthogonal and oblique intersection, respectively, 2) Apparent independence of crossing/blunting behavior on the friction coefficient for orthogonal intersection, 3) Dependence of the stresses required to promote crossing on the intersection angle between the HF and NF, 4) Existence of cases in which the hydraulic fracture crosses but then essentially ceases propagation such that all fluid is diverted to the interface. INTRODUCTIONHydraulic fracturing is a vital technology used to increase the productivity of oil, gas, and geothermal wells. Predicting hydraulic fracture (HF) growth is, in turn, critical to design of hydraulic fractures that grow to the desired length, accept the desired amount of proppant, and remain contained in the reservoir without unwanted height growth into surrounding layers (e.g. Economides and Nolte, 2000). The importance of HF modeling has prompted 6 decades of research during which simulators have become more efficient, more accurate, and have addressed a growing range of complexities (see review of e.g. Adachi et al., 2007).One of these complexities is the interaction between HFs and mechanical discontinuities such as natural fractures (NFs). Efforts in this area have been mainly driven by development of unconventional (i.e. low permeability) oil and gas resources because essentially all viable low permeability reservoirs, including shale gas/oil reservoirs, are naturally fractured to some degree (King, 2010). One of the most important questions for developing effective HF stimulation strategies in these reservoirs is whether the hydraulic fracture(s) is/are expected to be single-stranded or whether interaction with the NFs will lead to network-like growth. The basic building block for numerical simulators that can address this question (such as Kresse et al., 2013 and Weng et al., 2014) is whether an HF that intersects an NF will cross the NF or whether its growth will be captured by the NF so that additional fluid injection pressurizes the NF but does not generate ongoing growth of a new HF. These scenarios, including subcategories such as crossing with an offset, have been recognized for several decades (Daneshy, 1974; Warpinski and Teufel, 1987, and as recently reviewed and expanded by Chuprakov et al., 2013)."

Jan 1, 2015

By D. B. Stewart

This paper reports on an investigation undertaken to determine the exhaust gas temperatures of operating underground mining equipment. The effectiveness of platinum catalytic purifiers is discussed. From exhaust temperatures, it is concluded that LHD engines are highly loaded, haulage truck engines are moderately loaded and utility vehicle engines are lightly loaded.

Jan 1, 1979

By M. Palfreyman

"Most of the minerals employed in Canadian refractory production are imported; in fact, most of the refractories consumed in Canada are imported. Whereas this situation is partly due to a definite shortage of suitable raw materials, e.g., fire clays, it is possible that the potential of certain mineral deposits which could be usefully exploited has not been recognized. There are exceptions, notably magnesite and dolomite, from which refractories are produced in Canada.In many cases, known mineral deposits are located either in inaccessible areas or in areas where transportation would be a major economic factor. This paper lists some minerals and their respective known deposits which could be employed in the production of refractories, irrespective of economics."

Jan 1, 1973

By George W. Bain

Summary During the last three years the discovery of gold in the belt of volcanic and sedimentary rocks extending eastward from the Porcupine and Kirkland Lake gold-fields has caused a great deal of excitement in mining circles. The area is heavily drift covered, and every aid to the location of veins is eagerly grasped. A knowledge of the physiographic history of the area is of the utmost importance in the application of many of these aids. Evidence is presented to show that glacial erosion has lowered the general elevation very little below the pre-glacial level, and that many glacial erratics have been carried less than three miles southward. Probably a knowledge of the general geology of a: region was never more necessary to the understanding of the distribution and continuation in depth of the mineral veins than in this area. Four distinct granites occur in the region, and gold-bearing veins are genetically associated with only one of these. Two types of quartz-feldspar porphyries have been found, only one of which has any bearing on the locus of the mineral veins. Many other examples of this complexity of associations might be cited, but everyone goes to show that in most cases the economic importance of the deposits can be realized only after the regional geology is understood. A series of sandstone, limestone and shale intruded by granite lies unconformably below the Keewatin lavas. The latter are intruded by a gneissoid granite and are overlain unconformably by the thick series of Timiskaming greywackes and silts. These are intruded by carbonated syenites and syenite porphyries which have since been rendered somewhat schistose.

Jan 1, 1927

By Samuel B. Rombeger

The behavior of gold in hydrothermal systems is evaluated as a function of pH and oxygen and sulphur activities at temperatures to 250°C. Under conditions of stability of pyrite and argillic alteration as emblages, gold will be transported as bisulphide complexes. In systems containing significant amounts of arsenic, thioarsenide complexes may be important. Oxidation, dilution and reduction in sulphur activity would cause gold deposition from saturated solutions under these conditions. Gold chloride complexes will predominate under oxidized conditions where hematite or other oxides are stable and depo ition would result from increase in pH and/or reduction . Absorption and coprecipitation are po sible mechanisms of deposition for gold in certain low grade depo it . Low concentrations of gold in the transporting solution combined with the ignificant solubility of gold as bisulphide complexes, sugge t hydrothermal solutions rarely may be saturated with gold and coprecipitation with sulphides may be an important initial depositional process. Recrystallization of the sulphides in the presence of the hydrothermal solution would be re ponsible for release of gold to more table ite . Thi mechani m i supported by the close association of gold with pyrite in many hydrothermal gold deposits.

Jan 1, 1986

By K. Tarr

Acid-producing mine tailings are present at many active and inactive mine sites and pose an environmental liability due to the potential for acid rock drainage. Acid rock drainage originating from a tailings pile, a waste rock pile, or exposed sulfide-rich rock, can cause discoloration and turbidity in receiving waters, and the loading of ions mobilized by the acid can cause a decrease in aquatic flora and fauna, and reduction in the quality of groundwater. The primary cause of acid generation is the oxidation of sulfide minerals, predominantly pyrite and pyrrhotite. Considerable mine tailings are being stored on surface in vast tailings impoundment areas across Canada. In the tailings within this study, from the Sudbury, Ontario area, the sulfide mineral of primary concern with respect to acid generation is pyrrhotite. Different tailings types show varying and progressive degrees of oxidation correlating to their specific sulfur contents. The degree of oxidation is determined by the relative extent to which the sulfides have reacted as well as the depth of oxidation within the tailings. Natural Resources Canada, CanmetMINING is dedicated to research supporting the Green Mining Initiative, a program reducing business risks by demonstrating practices that reduce environmental impacts. In cooperation with the Canada Mining Innovation Council (CMIC), applied research aims to reduce land disturbance, waste volumes, and releases to the environment. By reutilizing tailings from vast impoundment areas as a component in backfill, the potential environmental impact would be lessened considerably, due to the reduced tonnage stored on surface long-term. From an operating perspective, there is a need for supplemental feed for backfill from time to time. The reclamation of old tailings for use in backfill is also driven by the fact that old tailings ponds may not be structurally stable, and it may be more cost effective to remove the tailings than to upgrade the impoundment structure. However it is imperative that these old tailings be fully characterized to determine their suitability for use underground, in order to ensure the long-term integrity of the resulting backfill matrix. A study was conducted to investigate the feasibility of tailings reclamation from old impoundment areas as a significant component in backfill. The materials were first physically and chemically characterized, followed by preparation of samples to determine optimal mix proportions for strength development for both paste and hydraulic fill compliance. It was found that the amount of oxidized tailings included in the backfill material had a profound effect on both the segregation and settling properties of the backfill matrix, as well as the mechanical properties of the samples. The strategies for decision-making, based on the criteria for material characterization, mining plan, and cost effectiveness are discussed.

Aug 1, 2013

By Baisheng Nie, Longlong Yang, Tao Yang, Wenjie Jia

"Gas adsorption in coal is an exothermic and physical process. Temperature might change during the dynamical process. In order to get the temperature variation of gas adsorption process, the experiment system which can test the temperature variation and analyze the thermal effect was established. Gas adsorption experiments under different conditions were done by using the test system. The results show that temperature increases during the adsorption process. It is an exothermic reaction process. Also, the temperature variation and the variation gradient increase with the increasing of equilibrium pressure. The temperature variation value is smaller if the experiment temperature is higher. The paper will provide basic experimental data for explaining gas adsorption mechanism better.INTRODUCTIONChina is the largest coal producer in the world while it also has the most serious coal mine disasters. According to the statistics, there are nearly a thousand coal mines in China including more than 110 the key state-owned mines risking to happen coal and gas outburst. Hundreds of coal and gas outburst occur each year which often causes serious casualties and economic losses (State Administration of Work Safety, 2007). With the continuing exploitation of the coal resources, the depth of the Chinese coal mines increases about 100 meters every year which causes the situation of gas accident becoming more and more serious (Xie et al., 2006).At present, the real mechanism of gas adsorption, desorption and the diffusion process in coal and the influence factor of it are not so clear. And because of the limit of prediction method and the technological level caused gas accident prevention theory and technology not so valid."

Jan 1, 2015

By H. S. Fowler

The Consolidated Mining and Smelting Company has been in the business of mining and exploration since its incorporation in 1906. The Company has reports written as early as 1890. Consequently, its files contain a very large number of reports, and also of maps, of ail descriptions. REPORTS Before describing the filing of maps, a brie{ note on our general system of filing reports will perhaps clarify the discussion. Reports of a non-periodic nature, primarily those based upon examinations by field engineers, are separated from all other data and filed in what we know as the Mine Series System. Each property on which reports are written is given a serial number, known as the Mine Series Number. This serial number is assigned at the time the first report is filed and it remains permanently identified with the property, regardless of its state of activity. Our mine series numbers now total over 5,000. The serial number for a property may be found by referring to an alphabetical index of properties. MAPS We found it necessary to divide maps into two groups: (1) Maps of properties (2) Maps of areas

Jan 1, 1944

By Tamas Kekesi, Gergo Rimaszeki, Tibor Kulcsar

The efficient purification of soldering waste material can be achieved in a single operational step by the electrolytic refining in pure hydrochloric acid - tin-chloride media. The complex formation of the ionic species may offer a beneficial level of natural inhibition. Using the PCR (periodic current reversal) technology, is efficient in affecting the morphology of the cathodic deposit. In order to optimize the process, the investigation of the solution stability and the electrode reactions is essential. The natural tendency of the Sn(II) oxidation and precipitation can be overcome by properly controlling the concentration of the main components and the ratio of Sn(IV)/Sn(II) in the electrolyte solution. Polarization curves were obtained for different concentrations tin and hydrochloric acid. Conclusions referring to the electrode reaction were derived from the overvoltage - current plots. The morphology of the deposit can be correlated with the exchange current density, also determined from the polarization curves. The cathodic current efficiency and the morphology of deposited metal are affected by the distribution of tin species and the principal electrolysis parameters.

Jan 1, 2011

By A. E. Flynn

THERE is at the present time a revived interest in amalgamation, due to the number of mines starting up, usually on high-grade ore, and utilizing this relatively cheap and convenient means of recovering gold, more especially in their initial stages of production. The marked increased use of the amalgamation process has revealed a dearth of amalgamators and there is no doubt the art of amalgamation has stood still for a generation or two and is not readily applicable to the modern practice of milling gold ores. Mill operators of long experience are learning the art for the first time and are giving it intelligent study, and considerable testing and research work is now being undertaken Most millmen consider amalgamation a simple process, and so it is when we have a clean ore with coarse gold, specially when stamps are used for crushing. In treating Nova Scotia ores by stamps and amalgamation, recoveries of 95 to 97 per cent are common and easily obtained. So-called 'under-water feed' is almost universally used in Nova Scotia and is quite beneficial. The water is supplied through jets between the dies and below the die surface and maintains this space as a live trap which catches the gold particles before they are overground and spoilt for amalgamation. With this method, the portion of gold recovered in the battery is higher than usual and often amounts to 80 per cent of the total gold in the ore, the remaining 20 per cent being caught on the plate. As a continuous amalgamator, the simple plate cannot be excelled. Some of the modern devices having moving or covered and not very accessible plates, which cannot be readily inspected and dressed to keep them in condition, do not give the best results in service. An exception might be drawn in the case of amalgamation of very heavy ore or concentrate which would bank up unless the plate is carried at such a steep inclination as to weep mercury. Difficulties in stamp-mill amalgamation are encountered when acid water is used or when grease is present. Also, certain sulphides and graphitic and talcose ores give trouble, resulting in poor gold recovery and high mer-cury loss. The older literature on gold milling deals with the common troubles of this type and the old-time amalgamator was well able to take care of day-by-day difficulties. When the difficulties were unsurmountable, the ore was classed as 'refractory' and other processes were used.

Jan 1, 1939

By Gordon S. Farnham

THIS paper summarizes the results of investigations carried out at Sydney Mines, N.S., and at Ottawa, following the disaster at Princess colliery, December 6th, 1938. The Honourable Minister of Mines for Nova Scotia appointed A. E. Cameron special investigator to enquire into and report upon the cause of the rope failure. Public hearings were held in Sydney Mines and evidence taken from many witnesses. The site of the accident was examined in detail and investigations made of the rope layout and colliery practice. At the request of the special investigator, the Department of Mines and Resources, Ottawa, kindly undertook technical and scientific examination of the broken ends of the rope. These investigations were carried out in the Metallurgical Laboratories of the Department of Mines and Resources, under the supervision of G. S. Farnham, Metallurgist for the Department. Valuable assistance in interpretation of many features of the investigation was received from other sources. Acknowledgment is due to Messrs. Stuewe, McCall, and Gordon, and other members of the staff of the Dominion Steel & Coal Corporation; to Messrs. Morrison and Scott, and other members of District 26, United Mine Workers of America; and to Messrs. Timm, Parsons, Haycock, Haanell, and other members of the staff of the Department of Mines and Resources, Ottawa, for helpful ad vice and technical assistance in assembly of information, and preparation of material and interpretation of evidence obtained.

Jan 1, 1939

By P. Kobylin, K. Haavanlammi, K. Valkama

"Base metals and precious metals can be recovered from a nickel matte or nickel concentrate using the Outotec nickel chloride leaching process. The raw material is leached with hydrochloric acid and the metals are recovered by solvent extraction, where ammonia is used to control the pH. Ammonium chloride is regenerated to ammonia and the side product of this step is calcium chloride solution. The regeneration utilizes either calcium oxide or calcium hydroxide. The calcium chloride solution is used to convert sulfuric acid into a hydrochloric acid solution while producing pure gypsum as a side product. The regeneration and reuse of ammonia and hydrochloric acid in this process will have a positive impact, from the point of view of both operating costs and environmental sustainability. This paper concentrates on the test work and technical concept development performed by Outotec to implement and develop chemical regeneration and recycling into a vital part of the nickel chloride leaching process.INTRODUCTION According to a nickel market analysis, the nickel market is expected to grow in the future. Main driver for this growth is the increase in stainless steel consumption as the living standards are equalizing globally. The expected increase in the amount of electrical cars and the need for nickel in the batteries of electrical cars also gives potential for the increased need for nickel in near future. At the moment the use of nickel in nickel-cobalt-manganese (NCM) and nickel-cobalt-aluminium (NCA) Li-ion batteries is in the range of 14 ktpa. It is estimated to increase to the level of 90 ktpa by 2025. In every era of the nickel industry, Outotec has been constantly developing new processes to create environmentally sustainable and economically viable processing routes. The Outotec® Nickel Matte Chloride Leaching process is a great example of a process that is flexible regarding raw material and could also treat nickel raw materials that are difficult for smelters. Outotec’s main options for pyrometallurgical nickel treatment include the Outotec® Direct Nickel Flash Smelting process (DON) and the Outotec® Ausmelt TSL process. The DON process is operated in Boliden Harjavalta Nickel Smelter in Finland. Ausmelt process is in use for example in Daye nonferrous plant in China. In the Outotec® Direct Nickel Flash Smelting Process, a sulphide nickel concentrate is processed in an Outotec Flash Smelting Furnace (FSF). Producing concentrates and processing them by Outotec Direct Nickel Flash Smelting to matte followed by hydrometallurgical refining offers a reliable route from concentrate to product. In the DON process, high-grade matte with low Fe content is produced in the FSF and the valuable metals in the slag are recovered in an electric furnace (EF). The Outotec® Ausmelt TSL process can use a large variety of raw materials (concentrates, secondary material and scrap metal) as feed. Fuel and oxygen are injected into the furnace through TSL (Top Submerged Lance) and this enables efficient smelting. Both Flash Smelting and TSL plants produce nickel mattes, which can be refined with Outotec hydrometallurgical processes."

Jan 1, 2017

By Pedram Sahba

In today?s emerging economy, pooling resources is a growing trend to reduce overall system costs. Two important resources of every maintenance department are repair shops and spare parts. In this work, we consider a system consisting of mine drills at multiple areas in a mine. In each area, a number of identical drills are operational. When a failure occurs, the defective component should be repaired in a designated repair shop. The failed component can be replaced immediately if a spare part is available. Otherwise, the drill is down until a component is repaired and put back into service. In this paper, the effect of pooling resources is examined, and the conditions under which it is beneficial to pool the resources are investigated. In addition, determining the optimal number of stand-by units, equipment or spare parts, in each case is of interest.

May 1, 2013

By S. Demetrio

China has a traditional segment of Copper Smelters with its own Chinese technology, typically small in size from 20.000 to 50.000 tCu/a, and they are responsible for the processing and production of more than 600,000 tonnes of blister copper per year. For occidental experts, like one of the authors, it is not so easy to believe that they are profitable, because the size and the use of old Blast Furnaces, but they are with simple and effective production lines. The authors are convinced that China has a good alternative to improve theses old copper production lines with small innovative changes in its process arrangement, jumping to higher level technology, more efficient in production, productivity and cost, assuring copper as a raw material for the country and its high speed development. The key to improve that the traditional Chinese Copper Smelter is white metal as an extra raw material as a first step doubling the copper production from raw materials and the complete replacement of concentrates by white metal (WM) in a second step increasing it four times or more as the final goal. It is not so difficult nor expensive to make it happen, but there are a couple of questions for implementing this innovation in the copper smelter industry: 1 - Will the old fashioned mentality be open to this new direction for China being the biggest copper consumer on one side, and the biggest copper Primary Producers on the other hand? and 2 - Will they be open to follow this "win-win" strategic way for both ends of the copper market? We don't know if anybody will take up the challenge to improve it but our responsibility as a consulting expert and a university professor is to put the alternative on table for others to decide whether to implement it.

Jan 1, 2007

By Beaumier. M., J. -P. Lalonde

"Les réultats obtenus dans les sols sur quatorze aires d'essai et six cheminements régionaux dans I'A bitibi-Témiscamingue indiquent clairement qu'il existe des variations régionales importantes dans les teneurs en éléments traces de l'horizon A1 formé sur l’épais recouvrement glacio-lacustre de cette région. Les anomalies obtenues correspondent à celles qui ont été décelées lors de précédents levés des eaux souterraines et du till de base.Selon les critères d'évaluation utilisés, treize des quatorze aires d'essai ressortent comme anomales dans Ie contexte abitibien; dix de celles-ci sont tres anomales. Ceci suggère fortement qu'un levé régional de sols, fondé sur une approche multi-éléments, identifierait entre 70 et 90 % des cibles géochimiques reconnues par des échantillonnages en profondeur. Les résultats d'un échantillonnage systématique effectué sur une région de 1000km2 viennent aussi appuyer cette hypothèse. Conséquemment, les sols formes sur les sédiments glacio-lacustres sont un médium très utile pour inventorier de grandes regions recouvertes par ce typ e de sédiments.L 'horizon A1 est Ie plus utile pour ce type de levé parce qu'i1 est facil e d échantillonner, qu 'it assure une plus grande constance du typ e de matériel échantillonne et qu'il contient des teneurs accrues.De multiples mécanismes de dispersion géochimique ont joué des rôles d 'importance variable pendant et après la mise en place des sédiments glacio-Iacustres. Les plus importants sont la pression hydrostatique, la diffusion chimique et électrochimique ainsi que la bio-accumulation. Si on veut progresser dans la connaissance de ce milieu complexe, on devra adopter une approche plus systemique tenant compte de I'interaction des mécanismes agissant dans l'environnement global avant, durant et apres Ie depôt du mort-terrain."

Jan 1, 1984

By J. D. Wright

This paper describes current milling practice at Endako Mines Ltd., a molybdenum producer in central British Columbia. The various steps in the crushing, grinding and flotation of the ore are outlined, with emphasis on the metallurgy of the latter operation. Tailings disposal and concentrate assaying methods are also described.

Jan 1, 1969

By J. Paturaud, A. G. Villemiane, J. Y. Buffiere, D. Fabregue, M. Perrier

In this work, a detailed characterization of the cyclic damage mechanisms on duty in car heat exchangers has been carried out in order to improve their reliability. The material which consists in very thin (<0.3 mm thick) sheets formed of 3 co-rolled aluminum alloys (4045 /3916/ 4045) has been brazed in order to obtain metallurgical and surface conditions representative of those of the real components. Fatigue tests at constant stress amplitude have been performed at room temperature and 120°C in order i) to characterize the cyclic resistance of the studied materials and ii) to study the effect of temperature on the fatigue damage mechanism. The mechanisms leading to failure have been identified from post mortem fractographic analysis. The Wohler curves obtained show that, contrary to common structural Al alloys, this type of thin sheet brazed multi material can be cycled for several hundred thousand cycles at very high stress level (> ~ 80 % of the tensile strength). This behaviour is analysed with respect to the microstructure resulting from the brazing process and the low number of grains present in the sample thickness (around 5 grains).

Jan 1, 2015