Search Documents

By N. M. Soonawala

Detailed regional geophysical and geochemical surveys, ground surveys and drilling were undertaken to follow-up the federal-provincial Uranium Reconnaissance Program (URP) over the 27,OOO-km2 Kasmere-Munroe area in northwestern Manitoba. An analysis of the URP data showed a fair correlation between the regional airborne radiometric results and lake-bottom geochemical results, both of which also correlated with the regional geology. More detailed surveys defined anomalies with greater precision within the broad zones outlined by the URP. The ground follow-up indicated that URP anomalies can be caused by varying degrees of uranium concentration in the rocks. Mineralization of interest was found in leucogranites at several locations within the survey area. Anomalous uranium concentrations were also found in coarse pegmatites and Hudsonian granitic intrusions. It can be concluded that large-scale regional surveys can be followed up in relatively short periods of time to yield meaningful results if a properly planned exploration sequence is employed, each stage of which successively narrows the area of interest.

Jan 1, 1979

By C. A. Young, H-H. Huang, L. G. Twidwell

Solid particles, especially oxides/hydroxides, develop an electrical charge on their surface when submerged in aqueous solution. Parks was able to relate PZC (point of zero charge) of an oxide to its minimum solubility and isoelectric point. Dzombak has compiled an extensive database for adsorption reactions on ferrihydrite surfaces using the double layer theory. The equilibrium calculational program, STABCAL has been used to extend the considerations of Parks and Stumm. The PZC for many hydroxides, complex oxides, and non-oxides have been investigated and the results are reported in the literature. Removal of arsenic and metals by adsorption on ferrihydrite as the substrate has been computed using ST ABCAL and the computational results are compared to experimental data. Absorbents other than ferrihydrite such as aluminum hydroxide are also discussed.

Jan 1, 2005

By D. Warkentin, M. Tomlinson, A. Nacu

"This study focuses on comparing the “blinding” effectiveness of various organic additives as part of a general review of using organic additives to mitigate preg-robbing and improve gold recovery during cyanide leaching of carbonaceous gold ores. The laboratory results compared the impact of various organic additives on the prevention of gold adsorption using both activated carbon and ore samples containing carbonaceous matter, generally referred to as total carbonaceous matter (TCM). Although several organic reagents were found to have a significant blinding effect on activated carbon, these results did not translate into increased gold leaching efficiencies with actual ore samples.INTRODUCTION Preg-robbing refractory ores, which contain carbonaceous matter, have been problematic in cyanide plants for many years. In industry, preg-robbing by carbonaceous matter may be mitigated using various techniques including flotation, to remove the carbonaceous matter; addition of blinding agents, to passivate the carbon surface and prevent adsorption of gold cyanide complex; roasting, to partially or fully destroy the carbonaceous matter; chemical oxidation (Abotsi & Osseo-Asare, 1986); pressure oxidation; or microbial deactivation (Dunne, Staunton, & Afewu, 2013). Carbon-in-Leach and Resin-in-Leach are also used as process alternatives in which activated carbon or resins are used to compete with the carbonaceous matter for gold cyanide adsorption. For highly preg-robbing ores, thiosulphate leaching may be considered as an alternative to conventional cyanide chemistry (Baláz, et al., 2000). Natural carbonaceous matter is composed mainly of hydrocarbons, organic acids, and graphitic/amorphous elemental carbon. Natural elemental carbon that behaves as activated carbon is considered to be the main reason for preg-robbing, although the true nature of this phenomenon is not fully understood (Tan, Feng, Lukey, & van Deventer, 2005). In general, the hydrocarbon fraction is assumed to have negligible interaction with gold, while organic acids, such as humic acids, may form complexes with gold, inhibiting its extraction in cyanide solutions. Organic reagents have been used for blinding carbonaceous matter in gold ores prior to cyanidation. Abotsi & Osseo-Asare (1987) tested various organic compounds, with two possible effects in mind. First, the organic compounds were expected to adsorb onto the surface of the solids as anionic/cationic species; the resulting electrostatic interactions between the Au(CN)2- anion and the negatively/positively charged surface would inhibit/enhance the gold uptake. Second, the organic reagents were expected to coat the surface of the carbonaceous component in the ore, limiting the available adsorption sites and reducing gold losses. Optimal reagent dosage depends on ore mineralogy, maturity and surface area of the carbo"

Jan 1, 2019

By T. W. Wlodek

"AbstractThe results of research into the fatigue properties of SAE 1080 carbon steel and nickel-chromium-molylbdenum steel for mining drill rods are analysed and described in detail.The effect of water corrosion on the fatigue strength of drill rods of these two steels in the as-rolled condition has ,been investigated and the beneficial influence of shot-peening on their dry and water-corrosion fatigue strengths determined by employing the method developed previously (1).Eight S-N curves for as-rolled and shot-peened mining drill rods under both dry and water corrosion conditions have been derived and their shape and relative position are discussed. The main features relating to field performance of the drill rods are analysed.Purpose of Research and Outline of ProgrammeDRILLING holes in rock and ore by means of drill rods attached to a pneumatic drill is a basic procedure required in mining operations. Detonation of explosives placed in these holes is at present the only practical method of breaking down the rock and ore.A drilling rod is supported by its bit end in the drilled rock. Its shank end, fixed in the drilling machine, transmits impact energy to the cutting edges of the bit. On the field performance of the drill rod depend a number of basic mining operations such as sinking, drifting, and stoping. The drill rod is there-fore regarded as one of the most important tools used in the mining industry."

Jan 1, 1952

By H. Marquis

The present paper consists of a survey of the literature on the problems of abrasion and wear of metals and materials by suspended matter. This problem is a very general one in industry, and is especially notice-able in the operation of cyclones and other types of dust collectors. The problem of abrasive dust in corrosive gas environments, such as commonly encountered in metallurgical industries, is particularly severe. Very little work has been done in the study of this type of abrasive wear, especially at high temperatures. However, a general review is presented here of all the work published on related subjects, such as that involving sand erosion in turbines and water wheels and the effect of temperature on friction wear. Topics in this paper include: blasting wear by sand, quartz, limestone, silicon carbide and other refractory particles; methods of investigation; effects of velocity, temperature and *Canadian Armament Research and Development Establishment, Valcarter, P.Q. angle of attack; correlation between indentation hardness, scratch hard-ness and resistance to abrasion; the effect of protective coatings; resistance of various metals; etc.

Jan 1, 1962

By A. Takala, H. Cline, D. Girard

"This article describes the project development and successful implementation of a particle sorter at the Kensington mine. The Kensington underground gold mine and associated milling facilities are located within the Berners Bay Mining District on the east side of Lynn Canal about 45 miles north-northwest of Juneau, Alaska. The paper describes the project from concept, through the development phase, including test work confirming feasibility, to a discussion of operational data and includes shared experiences from operation and maintenance. The project has proven successful in recovering gold that was previously lost to the waste dump and has already resulted in a positive return on investment. The payback was achieved in less than one year.INTRODUCTION The first paragraphs of this paper describe Coeur Mining and the Kensington Mine, its history, geology, mining operation and mill. The second part of this paper gives a quick introduction to sensor-based sorting in general and X-ray transmission sorting (XRT) in particular. This article does not cover costs or economic impacts apart from the pay-back period for the investment at Kensington. Interested readers find more in information on this in the literature (Kleine & Wotruba, 2010; Robben, 2013). Since the publication about XRT sorting at TGME in Pilgrim’s Rest (Kleine, Riedel, Ketelhodt, & Murray, 2010), this is the first time that a comprehensive data set on gold ore sorting using XRT is published. Following chapters highlight the aim of the project for Coeur Kensington, project development through testing and operation before concluding. ABOUT COEUR MINING’S KENSINGTON OPERATION Coeur Mining is the largest U.S.-based silver producer and a significant gold producer with five precious metals mines in the Americas employing approximately 2,100 people. Coeur produces from its wholly owned operations: the Palmarejo silver-gold mine in Mexico, the San Bartolomé silver mine in Bolivia, the Rochester silver-gold mine in Nevada, the Kensington gold mine in Alaska, and the Wharf gold mine in South Dakota. The Company also has a non-operating interest in the Endeavor mine in Australia in addition to royalties on the Cerro Bayo mine in Chile, the El Gallo complex in Mexico, the Zaruma mine in Ecuador, and the Correnso mine in New Zealand. In addition, the Company has two silver-gold feasibility stage projects—the La Preciosa project in Mexico and the Joaquin project in Argentina. The Company also conducts ongoing exploration activities in Alaska, Argentina, Bolivia, Mexico, and Nevada. The Company owns strategic investment positions in several silver and gold development companies with projects in North and South America."

Jan 1, 2017

By Paul L. Broughton

"IntroductionThe coal deposits, all of lignite rank, of economic interest in Saskatchewan are associated with the Ravenscrag Formation (Paleocene). Several Cretaceous formations have less significant lignite accumulations (Broughton, Irvine and W'hitaker, 1974). The Swan River Group (lower Cretaceous) and Judith River Formation (upper Cretaceous) have the only coalbearing strata in the shallow subsurface of central Saskatchewan. The Swan River Group coalfield is relatively small and underlies only 15 sq km of the surface approximately 40 km south of La Ronge, Saskatchewan. An estimated 36 billion short tons are within 45 m of the surface. No reserve estimates are known to have been calculated for the coal-bearing Judith River Formation exposed at the surface in the vicinity of the South Saskatchewan River valley in west-central Saskatchewan. Although no coalfields have been delineated, lignite beds up to 1.8 m thick have been intersected in test holes. The coal-bearing upper Cretaceous and lower Tertiary strata of the northern Williston Basin extends the full width of southern Saskatchewan for 650 km, and from the United States border 120 km north to 50° latitude (Fig. 1). Only the coalfields of the Ravenscrag Formation, because of their economic interest, will be considered further. There are four major coalfields. They are, from east to west: Estevan, Willow Bunch, Wood Mountain and Shaunavon (Cypress) coalfields. Cumulative lignite seam thickness for each basin is 10 -15 m (Figs. 2 and 3). The origin of each coal basin, resource calculations, seam stratigraphy, and mining activity are discussed. Regional Setting The Williston Basin is an ellipsoidal depression in the Precambrian basement, centered in western North Dakota and marginal to the exposed craton of northern Saskatchewan and central Manitoba (Fig. 1). The sediments of the basin range from Cambrian to Pleistocene in age and have a maximum known thickness of 4614 min western North Dakota. A maximum of 3200 m is recorded in southern Saskatchewan. Most structural deformation is late Cretaceous to early Tertiary (Paleocene) in age, coinciding with the Laramide Orogeny. The pre-Laramide Williston Basin, with a depocenter near Williston, North Dakota, began developing during the middle Ordovician, or possibly earlier."

Jan 1, 1985

By W. A. Lang

COAL of sub-bituminous rank underlies much of the plains area of Alberta. This coal is geo-logically young, and occurs in Belly River and Edmonton strata of Up-per Cretaceous age. Generally, the seams are flat-lying, but in some areas they may dip as much as 5 degrees. The overburden, composed mainly of glacial clays and sand-stones, may vary in depth from a few feet to several thousand feet. Recovery of the coal has 'been by drift, slope, and shaft underground mines, and by open-pit stripping operations. Production has been obtained from a large number of mines, most of which have been relatively small and with preparation equipment limited to a loading tipple with screening facilities, and a picking belt where high-ash materials can be removed from the larger sizes. The coal has been sold for domestic and industrial space-heating, for production of process steam, and for power generation. In re-cent years competition from natural gas, propane, and oil has seriously interfered with the production and marketing of sub-bituminous coal, especially with the disposal of the smaller sizes at a realistic price.

Jan 1, 1958

By D. K. Matlock, D. J. Hamre, J. G. Speer

Ultrafine ferrite (UFF) grains may be produced in surface layers of plate steels using controlled intermediate cooling followed by deformation. Experiments were conducted using a 0.12 C - 1.26 Mn steel on a Gleeble 1500 hot deformation simulator. Taguchi designed experiments were used to evaluate prior austenite grain size, intermediate cooling rate, intermediate cooling temperature, intermediate hold time and amount of reduction in order to observe the effects of variables and their interactions on the final microstructure while minimizing the number of required test runs. Evaluation of resulting microstructures and mechanical properties revealed a preferred thermal and mechanical history for developing ultrafine microstructures in surface layers of plate steels. Application of the fundamental concepts of phase transformations to industrial plate rolling is considered.

Jan 1, 2004

By A. M. Simons

Cyanide destruction by Caro’s acid is one process commonly employed by gold operations to meet regulatory requirements and/or the International Cyanide Management Code compliance for weak acid dissociable (WAD) cyanide in cyanidation tails or waste water from such operations. Typically smallscale bench tests to evaluate and assess the suitability of the Caro’s acid destruction process are conducted. Additionally, the experimental procedure used during these preliminary investigations may also differ from that implemented at the full-scale. This paper presents the results from a fundamental investigation of the Caro’s acid process to establish a more detailed understanding of the impact that the experimental procedure has on the destruction of cyanide. In particular, it was found that the control of pH was important to avoid copper(I) cyanide precipitation at low pH and maximise WAD cyanide destruction. Residual peroxide in the preparation of Caro’s acid has the potential for subsequent cyanide destruction and could be exploited.

Jan 1, 2014

By Robb. V. M., F. Walraven, L. J. Robb

"Abstract -The old Albert Silver Mine is a polymetallic deposit comprising concentrations of Cu­ Pb-Zn-Ag-U-F within a set of sub-parallel quartz-hematite veins which occur within the fine-grained apical phase of the 2050 Ma old A-type Bushveld granites. Mineralization occurs as an early pyrite­ chalcopyrite-arsenopyrite-galena-sphalerite-(argentiferous) tetrahedrite paragenesis followed by a later, more oxidized assemblage comprising chlorite-hematite-fluorite-pitchblende. Accumulation of metals appears to have taken place at the interface between a coarse-grained porphyritic granite and an overlying fine-grained phase: veins occur in the latter and represent leakage of magmatic fluids from the differentiated, water-saturated, subjacent granite.Mineralization processes in the Bushveld granites are believed to be related to long-lived circulation of dominantly magmatic fluids stimulated by the high heat productive capacity of the host rocks. Endo- and exogranitic tin-tungsten and base metal mineralization formed during an evolving hydrothermal system that lasted for several hundred million years, forming innumerable small- to medium­ scale polymetallic deposits. At the Albert Silver Mine, unroofing of the cover sequences at circa 1600 Mato 1700 Ma resulted in the incursion of lower-temperature, high-f02 meteoric fluids which remobilized the earlier sulfides and introduced the paragenetically late U-F mineralization ."

Jan 1, 1994

By J. P. Weiler

The increasing use of high-pressure die-cast magnesium alloys in the automobile industry requires a better understanding of the mechanical properties, the microstructure, and particularly, the relationship between these two. The goal of this study is to first understand the microstructural features which control the mechanical properties observed from an AM6OB magnesium alloy, and second, to be able to predict the local mechanical properties based on microstructural features encountered in different areas of the die-cast component. The two main tools used in this study are spherical indentation testing, used on local areas of the die-cast magnesium alloy AM6OB to detect changes in microstructure and mechanical properties, and X-ray tomography, used to non-destructively investigate the internal porosity in a sample. The results from these tests are then used to predict the local mechanical properties such as the yield stress, the strain-hardening characteristics, and the fracture properties of the AM6OB component.

Jan 1, 2006

By Jaeheon Lee, Junmo Ahn, Doyun Shin

"Many alternative leaching systems including bacterial leaching have been introduced to avoid passivation on the surface of chalcopyrite and to increase the leaching efficiency of copper from chalcopyrite. Recently, glycine, one of the simplest amino acids, has been emerging as an efficient and environmental-friendly lixiviant to recover copper. In the present study, an alkaline glycine–peroxide lixiviant system was used to leach copper from chalcopyrite concentrate and the leaching mechanisms were also investigated by a suite of kinetic studies under different conditions. The chalcopyrite concentrate contains 28.8% copper with 30.8% sulfide sulfur. The effect of concentration of glycine and hydrogen peroxide of the leaching solution was investigated. Glycine concentration was varied from 0.5 to 1.0 M and the hydrogen peroxide concentration was changed between 3 to 5%. Leaching time and pulp density were also varied. Hydrogen peroxide is an oxidant of the system and the leaching efficiency with periodic additions of the peroxide was also studied. A mineralogical study was performed using XRD and SEM. To investigate the surface of the residue materials, XPS was used to see if any passivating layer was formed during the leaching. Detailed results from mineralogical, chemical, and metallurgical studies will be presented and discussed.INTRODUCTION The greatest global resource of copper is low-grade chalcopyrite and heap bioleaching may be the only economic option for its processing. However, formation of a passivating layer on the surface of chalcopyrite slows down the oxidation reaction and reduces the efficiency of the process."

Jan 1, 2017

By Olanrewaju A. Ojo, Xu Wang, Jian Xin Dong, Lina Zhang, Jerzy A. Szpunar

"The influence of crystallographic orientation on the pitting corrosion behavior of Ni-Fe-Cr alloy 028 was studied by a combination of X-ray diffraction (XRD), electron backscatter diffraction (EBSD), potentiodynamic polarization technique and atomic force microscopy (AFM). The results show that there is anisotropy of pitting corrosion that strongly depends on crystallographic orientation of surface planes. The distribution of pits frequency in standard stereographic triangle shows that the crystallographic planes close to {100} are more prone to pitting corrosion compared to planes of {110} and {111}. The calculation of surface energy (001) and (111) shows that the planes of high packing density of atoms have low surface energy with concomitant strong resistance to pitting corrosion. A correlation function between crystallographic orientation and pitting corrosion susceptibility suggests a method not only to predict the pitting resistance of a known textured materials, but also to improve corrosion resistance by controlling materials texture.INTRODUCTIONNickel-iron-chromium(Ni-Fe-Cr) alloys are widely used in various industries and engineering sectors due to their combination of good mechanical properties and high corrosion resistance(Hibner, 2001; Thomas, 2006; Ghosh, 2005).Ni-Fe-Cr alloy 028 (alloy 028)has such important characteristics worth mentioning. Alloy 028 contains high amounts of nickel, copper and molybdenum which improve its resistant to corrosion attack in reducing medium, and presence of high level of chromium makes it more resistant to oxidizing species. Moreover, alloy 028 is less expensive because of higher amount of iron compared to other similar alloys. Currently, alloy 028 is manufactured as evaporator tubes applied in the phosphoric acid production; production tubing and casing used in deep and sour gas wells; heat exchangers employed in nuclear power plants, and seawater-carrying piping and seawater-cooled heat exchangers (Bankiewicz, 2012; Kivisäkk, 2003; Gómez, 2003; Xian, 2012; Bellezze, 2004)"

Jan 1, 2017

By K. S. Coley, M. A. Rhamdhani, G. A. Brooks

Interfacial phenomena in high temperature reactions such as between iron alloy and slag is well documented but not fully understood. It is believed that a gradient of oxygen concentration plays an important role to the occurrence of such phenomena. This article describes the results from the continuation of the study of interfacial phenomena between Fe-Al alloy droplets and CaO-SiO2-Al2O3 slag. Materials characterization techniques involving microscopic observations, depth profiling, bulk, point analysis and were carried out. The roles of oxygen as well as other factors that contribute to the interfacial phenomena were evaluated. The results and their implications to steelmaking will be discussed.

Jan 1, 2004

By E. Swartzman

This paper presents a general re-view of the various methods of briquetting coals, with and without the aid of a binder, with special reference to the production of a suitable briquette from Nova Scotia 'fines' for re-blending with industrial coal. From the economic and technical viewpoints, either small stoker-sized briquettes made with about 4 per cent asphalt in standard low-pressure double-roll presses, or briquettes made without binder in high-pressure double-roll presses, appear to be the most reasonable solution at present.

Jan 1, 1959

By David Thomas, Charles Harper, Brian Watters

The Star-Waddy Lakes area lies withjn the northeasterly-trending early- to mjd-Proterozoic volcanoseilimentary-pl utoruc belt referred to as the La Range Domllin. In the area investigated the domajn is composed of the Central Metavolcaruc Belt which is bordered by metasedimentary belts of the Crew Lake and MacLean Lake Belts to the northwest and southeast respectively. The boundaries between the Central Metavolcanic Belt and the flanking belts are generally marked by prominent zones of shearing. The volcanosed imentary succession is intruded by a variety of ultramafic to felsic plutons which, on the basis of lithology, field relations and geochronology, can be broadly subdivided into three groups or episodes. These are: a) an 'early' (ea. 1866 Ma), possibly subvolcanic, episode marked by composite intrusions ranging from gabbro-diorite to granite, b) an 'intermediate' (ea. 1854 Ma) plutonic event distinguished by more homogeneous felsic intru ions ; and c) a 'later' (ea. 1835 Ma) event characterized by leucocratic quartz-rich grani te intrusions. The La Range Domain has undergone polyphase deformation with a strongly developed northeast-trending structural grain. Large scale folding is manjfested by large regional sy nforms, arcuate and triangular patterns associated with many of the plutons and by tight to isoclinal folds within the adjacent metasedimentary belts. Inhomogeneous strain characterizes much of the Star-Waddy Lakes area. With strain gradients being typically very steep, zones of high strain consisting of zones of extreme extensional fabrics, discrete shearing, as well as broader zones of cataclasis and structural slicing, are often juxtaposed with areas of relatively minimal deformation . Dilation structures tend to favour these zones of highly contrasting strain. Late, brittle fractures, faults and shear zones are widespread and appear to be particularly important as loci for gold mineralization. Metan1orphic mineral assemblages indicate that upper greenschist to middle amphibolite facies conditions were attained. Geological and geochenucal evidence indicates that the Central Metavolcanic Belt evolved in an island arc environment. Metavolcanic rocks from both the Waddy and Star Lakes areas display similar characteristics on variation diagrams (e.g. AFM and the Jensen cation plot) in that the dominant trend is calc-alkaline with some basic to intermediate types having a mildly tholeiitic character. A few samples from the southern end of Lower Waddy lake display komatiitic to basaltic-komatiitic afl'injties. The relatively immobile minor and trace elements (e.g. Ti , Zr, Nb, Y, Cr) provide reliable characterization of the metavolcanics, particularly of the basalts, which have highly distinctive trace element properties. Geochemical patterns for the basalts are similar to those for modem volcanic arc basalts. Low initial 87Sr/86Sr ratios (0.7017 - 0.7019) are consistent with a subduction-related origin for the volcanics. The major plutons have chemical properties typical of volcanic arc granites and are largely calc-alkaline in character, showing little chemical variation from the volcanics.

Jan 1, 1986

By S. Nafisi

Permanent mould casting may be regarded as a near net shape manufacturing process where simple to very complex shaped engineering components are fabricated with high degree of precision in a metallic mould, In this group, High Pressure Die Casting (HPDC), have attracted more attention because of its production rate, where both liquid and semisolid metals (SSM) can be cast with high degree of precision and versatility. The SEED process, Swirled Enthalpy Equilibration Device, the new process for semi solid metals slurry production route, consists of two steps: The initial step involves extracting specified amount of heat from the molten metal to generate liquid-solid slurry, i.e, mushy structure, followed by drainage of remaining liquid to produce a compact free standing feedstock for rheocasting operation. In this paper, microstructural evolution during the process and some initial casting results of automotive components an also reported.

Jan 1, 2005

By Jean G. Fortin

The manufacturers' proposed technology has been a key factor in selecting production, mobile and fixed equipment in order to achieve the targets set in our 2026 mining plan. This paper will present an overview of the most recent technologies adopted by Québec Cartier Mining Company for communications, power supply, dewatering, drilling, loading, hauling and processing. All these new technologies contribute to the improvement of our day to day operations while operating with a state of the art asset reliability program.

May 1, 2007

By M. F. Goudge

BRUCITE associated with highly metamorphosed Precambrian limestone was discovered in the vicinity of Rutherglen in northern Ontario by the writer during field work on the limestones of that district in 1937, and later was identified in similar limestone at Bryson and Wakefield, Quebec. The brucite occurs as granules disseminated through the limestone (Figure 1) and comprises from 20 to 35 per cent of the rock. Such rocks may be referred to as predazzites or pencatites, depending on the proportions of the constituent minerals. In this paper, however, the general term brucitic limestone is used to designate limestone containing brucite. In none of the deposits does the magnesia content of the rock approach that of magnesite, and in the deposits near Bryson and Wakefield the magnesia content is only that of dolomite. Therefore, without some method of concentrating the brucite, the deposits would be of little or no more value as a source of magnesia than is ordinary pure dolomite, which is abundant in many parts of Canada. Investigations in the laboratories of the Bureau of Mines have, however, resulted in the development of a method whereby, from certain of the deposits, pure calcined brucite, or magnesia, in granular form can be obtained, apparently at a cost that will enable it to compete in eastern Canada with imported magnesia. The granular magnesia so obtained appears to be highly suitable for use in basic refractories, for making magnesium metal, and for various other purposes for which magnesia is commonly used. Prospecting in the neighbourhoods of the original discoveries has resulted in a number of other deposits being found in each of the three areas, and there is now apparently available s1.dficient brucitic limestone of a grade that will lend itself to commercial exploitation to supply for many years a large part of the present and prospective Canadian market for magnesia and its products. Furthermore, it is expected that additional deposits will be discovered as prospectors and others become more familiar with the appearance of brucitic limestone.

Jan 1, 1940