Search Documents

By Don Welch

Pressures for change ?Land use constraints ?Project financing ?Local communities ?Environmental issues ?Sustainability requirements ?Stricter regulatory procedures ?Technical excellence ?Reduce risk ?Impacts of failure & non-compliance

May 1, 2010

By H. Wyslouzil

"The Kelsey Centrifugal Jig is a gravity separation device which utilizes the principles of the conventional mineral jigs but with the additional feature of being able to vary the apparent gravitational field. This is accomplished by utilizing the specific induced movements of the conventional jig within a centrifuge.Pilot plant trials have been underway since July 1988 to evaluate the potential applicability of this technology to various process streams at Rio Kemptville Tin.The grade/recovery relationships for samples treated in the jig were consistently better than results obtained from tables. Recoveries of more than 90% were attained at concentrating factors ranging up to 20. When compared with electrostatic separators, the jig achieved equivalent metallurgical results in a two stage process, without the expensive requirement of filtration and drying. Recoveries exceeding 96% were achieved with final concentrate grades averaging higher than 60% tin.INTRODUCTIONMineral jigs have been used for hundreds of years. Many different types have been developed, and each one has numerous variations. In recent years, the idea of applying centrifugal forces to conventional jigs has been put to practical tests and today a number of units are in commercial production. In principle, by enhancing the apparent gravitational field, it should be possible to recover finer particles by overcoming viscosity and surface effects which tend to limit existing gravity devices. In addition, it may be possible to use gravity to separate minerals with much smaller specific gravity differences."

Jan 1, 1990

By Richard Frentress, Dave Donelon, Robert Henderson, Mike Warnert

"The Round Mountain gold mine is an open-pit mining operation located 97 kilometres north of Tonopah in Nye County, Nevada. Gold has been produced from the property since 1906.Gold is currently recovered using a combination of four independent processing operations. These include a 10,000 ton per day mill, a 30,000 ton per day, crushed ore heap leach, a 150,000 ton per day, run-of-mine ore heap leach and a small high-grade gravity concentration circuit. In 2002, Round Mountain Gold Corporation produced 755,494 troy ounces of gold at a total direct operating cost of US$2.14 per ton ($193/oz).This paper presents a summary of the Round Mountain operations and discusses some of the processing innovations that have enabled the mine to profitably recover gold from a large low-grade ore body.INTRODUCTIONRound Mountain Gold Corporation is a 50/50 joint venture between Kinross Gold Corporation and Barrick Gold Corporation. Kinross acquired its ownership interest in the Round Mountain mine upon completion of combination with Echo Bay on January 31, 2003. The joint venture partners continue to support an aggressive exploration program in the vicinity of the mine in order to add reserves and extend the mine life.The Round Mountain mine currently operates a conventional open pit that is approximately 8,200 feet long, 4,900 feet wide and 980 feet deep. Mining is conducted on 34-metre benches by electric shovels and front-end loaders paired with 150, 190 and 240-ton haul trucks. Blasthole samples are collected and assayed and provide the control for ore segregation. Based upon these assays, blasted pit rock is determined to be run-of-mine Dedicated Pad ore, crushed Reusable Pad ore, high-grade ore or waste.Gold is recovered using a combination of four independent processing operations. These include run-of-mine ore heap leaching (Dedicated Pad), crushed ore heap leaching (Reusable Pad), milling and the gravity concentration circuit. Non-mineralised rock is delivered directly to the waste dumps. Low-grade ore is trucked directly to the Dedicated Pad and medium-grade ore is crushed and placed on the Reusable Pad. High-grade ore is handled in one of three ways: 1) leached on the Reusable Pad and offloaded to the mill; 2) sent directly to the gravity plant with tails reporting to the mill; or 3) sent directly to the mill or mill stockpile. The gold particle size distribution of highgrade ore determines the processing method."

Jan 1, 2005

By J. C. Escobedo, J. M. Almanza, A. Flores, Cortés. D. A.

Secondary aluminum dross, which has been exposed for several years to atmospheric conditions, was characterized using chemical analysis, X-ray diffraction, optical and scanning electronic microscopy, and energy-dispersive spectroscopy. Based on the characterization, a method to purify the solids is presented. This method starts with the washing of the dross in boiling water to eliminate the soluble compounds like Na and K, followed by the physical separation of the metallic aluminum by milling and screening. Finally, an acid lixiviation process is applied using three different acid solutions, HCl, HNO3, and H2SO4. The best results were obtained using HCl. The main insoluble components of the dross after lixiviation were Al, SiO2, and Al2O3. MgAl2O4, AlN, Si, and Na2Al22O3·2H20 species were also found. Based on the alumina content, the solid product could be suitable as a raw material in the manufacture of castable refractories or metal matrix composites.

Jan 1, 2005

By Paul Hosford, Tim Haldane

"The paper describes the fast-track development of the project from feasibility study through to detailed design and construction, highlighting the process adaptations for handling sticky ore and water management in a tropical environment, and subsequent commissioning and operating experience of the mine. The paper discusses the geological setting, the environmental and socioeconomic considerations in developing and operating a mining operation in an underdeveloped country and the logistical challenges involved in bringing a large capital investment into Central America.INTRODUCTIONGlamis Gold Ltd. acquired the San Martin project in Honduras as a result of its merger with Mar-West Resources in late 1998. Despite the prevailing low gold price environment at the time of acquisition, Glamis anticipated rapid development of the San Martin project due to the quality of the deposit and other positive factors.Following favorable exploration and permitting activities in the first half of 1999, Glamis prepared a Feasibility study. In October 1999, Glamis decided to proceed with the development of the project and selected Hatch to provide the engineering, procurement and construction management services for the project. The San Martin project was in full-scale commercial operation approximately 14 months after the receipt of Board approval, and by July 2001 the San Martin project was operating at approximately 150% of its feasibility design capacity."

Jan 1, 2002

By A. J. Williams

"Conventional base metal milling practice normally consists of crushing, grinding and cyclone classification followed by flotation. It is the authors' belief that the commencement of flotation after cyclone classification leads to inferior metallurgical results and that implementation of flotation of grinding mill discharges can result in increased recovery due to reduced overgrinding, reduced activation of contaminating minerals and improved dewatering circuit results due to the production of coarser concentrates.The concept of recovering minerals from the discharge of grinding mills is not new! Gold concentrators have utilized jigs and flotation cells while iron ore plants have employed magnetic separators to recover gold and magnetite respectively from the discharge of grinding mills. More recently, a Reichert cone has been used to recover sulphide and oxide base metal minerals from screened rod mill discharge. 1To the authors' knowledge, the first application of flotation of base metal minerals from the discharge of a production plant grinding mill was at the Lake Dufault concentrator of Corpor'1tion Falcon bridge Copper. Located 10 miles north of Noranda, Quebec the Lake Dufault concentrator commenced operations in August, 1964.The installation of flot11tion cells in the Lake Dufault grinding circuit proved so successful that an identical system was installed in the Manibridge concentrator of Falconbridge Nickel Mines Limited. Located 90 miles southwest of Thompson, Manitoba the Mamibridge concentrator commenced operations in June, 1971 and due to exhaustion of economic ore reserves discontinued production in May 1977."

Jan 1, 1984

By M. G. Dellow, D. W. Hendriks

"In early 1988 the decision was made by Noranda Minerals Inc. to install pressure filters at the GECO mill to replace the vacuum disk filters and bunker-C fired rotary kiln dryers. Two filters were installed, one for copper concentrate and one for zinc concentrate. Completion of the project was scheduled for the third quarter of 1989. The filters were made operational in October 1989. Some work remains to be done yet on loadout conveyors for total project completion. Capital expenditures for the project have been approximately $2,700,000 to date. The paper describes the selection criteria for the filter, the installation, startup and associated problems.1. INTRODUCTIONThe filter model chosen for the project was the Verti-Press model VP-50-6(7) (Figures1 ,2 and 3) by Filtra Systems of Farmington Michigan, USA. The decision to purchase the Filtra Systems filter was based on gaining familiarity with a different, mechanically simpler pressure filter than the Larox design and to a lesser extent a necessity for repairs to the the disc filter, rotary kiln dryer system used at the GECO operation for its' copper and zinc concentrates. The fact that it is manufactured in North America was an important consideration. The same basic principles of pressure filtration as the Larox machine are used but the implementation is quite different and somewhat simplified with some interesting innovations. 2 filters were installed to allow direct and immediate comparison of the same machine on both fine and coarse materials. Copper concentrate is reground for cleaning on the flotation circuit while zinc is not. Screen analysis of composited samples of concentrates for 1988 indicated that expected copper concentrate would be approximately 66% minus 400 mesh and zinc 50% minus 400 mesh (Tables 1 & 2).The filter is composed of six horizontal chamber module layered vertically and held together in a frame by 1 O large bolts; torqued down to 4000 ft-lbs. 6 individual belts are used; each with its own drive system. The belts themselves are of a 3 piece design with a filter cloth portion, a support belt and a rubberized intermediate portion. They are held together with steel clipper lacings. A basic description (1) of the filter operation is as follows. ""The horizontal filler chamber is closed by hydraulically pressurizing seals across each end of the filter chamber to 200 psi. The feed pump then pumps slurry into the filter chamber. Suspended solids are retained on the filter belt and the filtered solution drains into a lower drip tray and flows from the filter by gravity. At the end of the filtration or feed cycle, a rubber diaphragm in the filter chamber is pressurized hydraulically to 100 psi pressure. This removes all free liquid from the filter chamber and the filter cake. After the diaphragms are retracted the filter cake is blown with compressed air to remove any residual cake moisture. The seals are then retracted and the belt is advanced to discharge the filter cakes. During the cake discharge the belts are washed with a spray header located at the drive end of the filter. The belt assemblies move one (1) complete revolution during the cake discharge cycle. The cycle automatically repeats until the filter is shut down by the operator."

Jan 1, 1990

By Ken Hester, Bruce Arthur

"Introduction""Pebble milling"" is a term used to describe secondary grinding done with rock pebbles rather than steel balls or other steel or metal shapes. This paper discusses pebble milling with particular attention being paid to uranium grinding circuits.Pebble milling is typically employed:a. where the cost of steel balls becomes exorbitant, as may be the case in an isolated area.b. where the extra steel added from steel ball consumption may be detrimental to further processing.c. where the over-all economics favour the use of pebbles rather than ball.Pebble milling differs from autogenous and semi-autogenous grinding in that a sized product has been removed from some part of the primary comminution circuit, and it is this sized product which is added as grinding media to the pebble milling stage. The pebbles do not necessarily have to be produced from the ore- ""foreign"" pebbles can be used. Also, pebble milling generally refers to grinding from a fine size, below about 6 mesh (3360 micron), with relatively small media, that is, secondary grinding. In South Africa, however, primary pebble mills are sometimes used to grind crusher house product, and thus function in place of rod mills. Pebbles for this service are large and heavy as they must weigh as much as balls used in similar service.The first large applications of pebble milling were in South Africa(n. ""Tube milling"" with pebbles started in 1904. The tube mill was simply a tumbling mill with a length to diameter ratio over two. A ""typical"" early tube mill was 5.5 ft. (1.7 m) in diameter and 16 ft. (4.9 m) in length. Diameters increased steadily. King(n mentions 8-ft. (2.4 m) units in his 1949 book. By 1961, the largest units discussed by Jackson('' were 12ft. (3. 7 m) in diameter."

Jan 1, 1989

By Alan D. Curtis

A standard planning block model for Phelps Dodge North America Operations has been developed to improve mine planning efficiency and performance in a skill starved environment. The model saves time on software management and training, consolidates data and standard information/output, enhances evaluation and strategic process, and improves communication between sites.

May 1, 2007

By T. Warren, R. Pender

"Significant strides have been made during the past decade to integrate the traditionally separate administrative functions of financial management, materials management and maintenance management.In 1983, Key Lake Mining Corporation (KLMC) brought on-stream one of the most technologically advanced mining operations in North America. There was a requirement to support this new facility with state-of-the-art management information systems.This paper will discuss the development and evolution of the corporation's computerized information systems with specific emphasis on the utilization of computer systems to assist maintenance personnel in performing their work activities:Note: In August of 1989, the administration and operation of the Key Lake Mine was assumed by CAMECO - A Canadian Mining and Energy Corporation.IntroductionThe Key Lake Mining Corporation was incorporated in 1979 and operates a $500 million uranium mining and milling complex located in northern Saskatchewan.The feasibility study and environmental impact statements for the Key Lake Mine were submitted in 1979and in August of 1981, following a public inquiry, approval to proceed with construction was granted. Ore processing commenced in October of 1983 and during 1984 a total of 10.4 million pounds of uranium oxide (U3O8) was produced. In 1987, an annual production of 13.5 million pounds was achieved clearly establishing Key Lake Mining Corporation as the world's leading producer of uranium oxide. Current ore resources are expected to extend production of the Key Lake facility into the year 2000."

Jan 1, 1990

By Bruce Jago, Joe Zhou, Chris Martin

"From the perspective of metallurgical processing, gold ores can be classified into free-milling and refractory ores. Their extractive metallurgy are largely driven by mineralogical factors such as: gold particle size, association with other minerals, coatings and rimmings, presence of cyanicides, oxygen consumers and preg-robbers, presence of refractory gold minerals and locking of submicroscopic gold in sulfide mineral structure etc. Gold process mineralogy helps address issues and problems related to gold ore processing. It provides useful information on process selection, flowsheet development, recovery improvement and reagent consumption optimization. By combining classic mineralogical techniques, modern instrumental analysis and diagnostic metallurgy, the mineralogist is able to balance the various types of gold occurrence in an ore. This paper will provide a broad review of gold process mineralogy and the techniques available, and use case studies to describe how they can be used together, to provide the complete picture of gold process mineralogy in an ore. Examples will be used where applicable.INTRODUCTIONSince the early 1980’s, a great deal of work has been done in the characterization of gold ores, particularly refractory ores (Gasparrini, 1983; Wang, 1984; Hausen, 1985; Haines, 1986; Henley, 1989; Chryssoulis et al., 1990; Wang et al., 1992, 1994; Kojonen, 1999; Simon et al., 1999; Hong et al., 2000; Pals et al, 2003). Process mineralogy has come into its own as a respected inter-discipline in the fields of mineralogy and metallurgy – a subject that occupies an important place in both research and industry. As the free-milling gold ores are being depleted and more refractory ores are being discovered and processed, gold process mineralogy receives more and more attention from both the mineralogist and metallurgist as it helps to solve various problems encountered during gold ore processing. Steadily rising gold prices are also stimulating the need for gold process mineralogy due to the increasing demand for and production of the yellow metal. At SGS Lakefield Research, gold process mineralogy studies are conducted routinely on all types of gold ores and mill products to assist in a wide variety of metallurgical projects. This paper will briefly discuss the gold ore types and gold mineralogy, review the common mineralogical factors affecting gold extractive metallurgy and the techniques available to gold process mineralogy, introduce the procedure employed at SGS Lakefield Researc"

Jan 1, 2004

By Jacques Ouellet, Ferri Hassani

"Within the mining industry paste backfill technology has evolved over the last two decades. This technology aims at producing safe and cost effective backfill of high strength. When used as cemented backfill underground the usual practice in the mining operations was to consider the backfill as a component under the production engineer responsibility. With its growing use in various site conditions some problems were encountered. Over time the mechanical characteristics of paste backfill could deteriorate. Investigations on these problems brought an increased understanding of paste backfill chemistry. Effectively, paste backfill is produced with tailings slurry having sometimes very complex chemistry and mineralogy. The bonding agents can be sensitive to the chemistry of these slurries. Today, a new understanding of the complex chemical reactions involved in cementing paste backfill is derived from concrete research literature. Cemented paste backfill is a manufactured product and as thus all steps involved in its making must be looked at. Both the processing engineers and mining engineers need to be involved. The proposed paper will go over the various developments and new understanding gained over the years on paste backfill chemistry. The authors had the opportunity to work with various Canadian mines that implemented paste backfill in their operations. Chemical alterations case study will serve to illustrate the importance of a good understanding of cement and paste chemistry. The authors will then conclude on research orientations needed to bring a more efficient use of paste backfill technology. The crucial role of the processing engineers in the paste backfill manufacturing will be discussed.INTRODUCTIONPaste backfill is usually prepared from a mixture of solids and water containing at least 15% particles smaller than 20 microns with the addition of binders for mechanical strength. Historically, tailings had been classified to extract the fines and only the coarse part was placed underground as sand slurry. Paste fill was researched in the last three decades to enable mining operations to use all the tailings, including fines, in backfill. The outcome of the early studies showed that paste fill provides high strength but due to preparation complexities and transportation problems is expensive. A greater understanding of the transportation mechanisms and advances in dewatering technology in recent years has resulted in more practical use of paste backfill."

Jan 1, 2002

By George A. Lawrence, J. C. McHardy

"Field operating experience with an improved flotation mechanism for handling various flotation applications is covered in this paper. Some aspects of designing flotation machines are also presented. Operating data from extensive testing of commercial size equipment under actual plant operating conditions in the following applications is detailed:1. Copper Flotation2. Fine Coal Flotation3. Base Metal Sulfide FlotationDesign features, design improvements, modifications tested, and overall performance data are reviewed. Some mecl1anical performance data as well as metallurgical performance results are presented. Some comparisons with conventional flotation equipment are reported in this paper.Flotation sizing theories are reviewed and an actual equipment selection ex2.mple is presented. Scale-up criteria used for developing large cells are briefly covered.The paper concludes with a brief review of anticipated future flotation equipment design needs. IntroductionThe mining/milling industry is faced with increasing pressure to cut costs while maintaining product quality and indeed, in some instances, expanding production. For copper, nickel, iron, molybdenum, lead and zinc sulphides, coal, phosphate and some other minerals;, flotation remains the primary method of concentration and recovery of the valuable mineral away from the gangue. Cost reduction in flotation can be broadly focused on two areas:1. Flotation Chemicals2. Flotation Equipment"

Jan 1, 1985

By M. J. Fairweather, Keith Lee, Naseem Mian

"The initial metallurgical response of the lead flotation circuit at Cominco Alaska's Red Dog Mine was substantially below feasibility expectations. A program of diagnostic mineralogical analysis pointed the way to a number of process improvements, including simplification of the flow sheet and installation of a large flotation column as a lead cleaner. A diagnostic mineralogical analysis of the improved circuit shows that inadvertent activation of both sphalerite and pyrite has been substantially reduced, resulting in significant improvements in metallurgical performance. Directions for further improvements to the circuit performance are suggested by the recent analysis.IntroductionRed Dog is a high-grade, sedimentary exhalative (sedex) deposit with relatively simple mineralogy. The primary non-sulphide gangue minerals are quartz and barite, with minor barium carbonate (witherite). The iron sulphate minerals, siderotil, rosenite and copiapite occur variably throughout the deposit. Mineral texture is variable ranging from liberated sphalerite grains visible to the naked eye to intergrowths, particularly between sphalerite and galena, to less than ten microns. Both pyrite and marcasite are present. To date no enhanced reactivity of marcasite has been observed. For this discussion, ""pyrite"" will be used to refer to both iron sulphide minerals. In common with other sedex deposits, Red Dog contains organic and sulphur impurities."

Jan 1, 1997

By R. O. Burt

"Gravity Concentration, the oldest form of Mineral Processing, remains of major importance to the Industry. Current applications of Gravity Concentration are briefly examined.The Paper details one approach to the development of a Gravity Concentration Plant, from laboratory and mineralogical techniques, through Pilot Plant testing, where applicable, to the actual design of the plant.INTRODUCTIONGravity Concentration, once the major method of concentrating minerals has, for much of the twentieth century been regarded, like the dodo bird, as obsolete. However, in more recent years it is enjoying something of a renaissance, and is once again being treated as a useful, economic alternative in the Mineral Processing Engineers' arsenal.An indication of the broad application of gravity concentration is the variety of minerals presently recovered. A list is given in Table 1; this list is not exhaustive."

Jan 1, 1984

By R. B. Barlow, J. A. C. Fortescue

Originally developed for use in mineral exploration, regional geochemical mapping based on stream (and lake) sediment sampling is showing broader application in other areas of the earth sciences and in environmental science. The purpose of this paper is to focus attention on the role of regional geochemical mapping in relation to geological and environmental studies. This is achieved using a descriptive equation for the chemical composition of a stream-sediment sample and then relating it to the use of successive approximations in geochemical and environmental investigations. The procedure is further qualified with reference to time and process in the formation of regional geochemical patterns. Examples are included of studies based on stream sediments related to bedrock geology, surficial geology, ecology and man's effect on the geochemistry of the environment. The range of applications of regional geochemical mapping in earth and environmental studies is outlined and some conclusions drawn regarding the future development of geochemical mapping under Canadian conditions.

Jan 1, 1980

Certain information contained herein regarding Champion Minerals Inc., including management?s assessment of future plans and operations, may constitute forward-looking statements under applicable securities law and necessarily involve risks, including but not limited to risks associated with mining exploration, operating costs, production costs, volatility of share prices, currency fluctuations, imprecision of resource and reserve estimates, environmental risks and ability to access sufficient capital from internal and external sources. As a consequence, actual results may differ materially from those anticipated in any forward looking statements. Plans, intentions or expectations disclosed in any forward-looking statements or information should not be read as guarantees of future results or events, and will not necessarily be accurate indications of whether or when or by which such results or events will be achieved. Except as required by law, Champion Minerals Inc., expressly disclaims any intention and undertakes no obligation to update any forward looking statements or information as conditions change. The historical mineral resources mentioned are strictly historical in nature and are non-compliant to National Instrument 43-101 mineral resources and mineral reserves standards, and should therefore not be relied upon. A qualified person has not done sufficient work to upgrade or classify the historical mineral resources as current National Instrument NI-43-101 compliant.

May 1, 2011

By P. Tolvanen, A. Jalili

"When hard times strike in the mining cycle, sites tighten their belts and focus on lowering their unit costs. Lower unit costs can be achieved by reducing expenditure, increasing production, or by a combination of both. Faced with these requirements, site personnel must turn to areas where they can focus their effort for maximum return. For many sites, both in Canada and overseas, focusing on improving flotation cell maintenance is one of the areas where gains can be made for minimum outlay. Due to resource limitations and/or lack of equipment understanding, maintenance on many sites is only conducted on a reactive basis, once equipment fails. This paper will promote the idea that mineral processors should become more familiar with their equipment so they can ensure that the plant’s ability to produce is not compromised. By better understanding the flotation equipment and ensuring the critical components are maintained, it should be possible to unlock value in an operation. Flotation equipment inspections will be discussed in detail, including key items to look for during these inspections. Potential approaches for predicting wear and change-out time for flotation equipment components will be also demonstrated. An example of one approach used at a South African nickel site will be given.INTRODUCTIONWith metal prices decreasing and operating costs rising, concentrator operators are looking for ways to improve their bottom line. Lower unit costs can be achieved by reducing expenditure, increasing production, or by a combination of both. To meet the expectation of shareholders, mineral processors must turn to areas where they can get the best return for their efforts. One area where there is a large opportunity for improvement is in the maintenance of flotation equipment.On many mine sites, both domestically and around the world, it is quite common to see the philosophy applied of repairing equipment only once it has failed. Though some sites have advanced enterprise management systems and monitoring programs, in the authors’ experience, the decision on flotation equipment maintenance is rarely made on a proactive basis. Two common trends that are evident in the mining industry are that operations are under pressure to keep the plant producing, and maintenance managers generally have very strict budget targets to meet. In addition to these factors, few sites have a good understanding of the financial implications of running with worn or broken flotation equipment. Knights, Jullian and Jofre (2006) summarize this situation well, stating that the lack of correlation between some commonly used maintenance performance measures and key business drivers can lead to maintenance being seen only as a cost center (that needs to be reduced) rather than a tool for productivity improvement."

Jan 1, 2015

By Tim Edwards, Richard Triglavcanin, Ian Arbuthnot, Darren Colwell, Brad Garraway, Ken Roberts

"In the mineral processing industries, there is an increasing need to design thickeners which are able to produce high density underflows usually referred to as “paste”.The behaviour of a flocculated suspension in compression needs to be well understood in order to arrive at a reliable thickener tank configuration (i.e. diameter, cone angle and depth) for a required paste result.As a suspension approaches paste consistency, it’s fluid characteristics change markedly. It develops a high yield stress, and may have an increased tendency to form agglomerates, which lead to a phenomenon known as “rotating beds”, “donuts”, or “islands”. These characteristics present challenges to the designer of the rake mechanism.The subject paper addresses the requirements for designing a paste thickener, covering the following topics:o Testwork for thickener sizingo Design of rake mechanismso Suspension rheology and effect on designo Case studiesTESTWORK AND SIZING FOR PASTE THICKENERSThickening slurries to the maximum possible density (paste) is becoming increasingly common. Applications such as Autoclave feed thickeners, paste backfill and some counter current washing (CCD) circuits are all examples of potential paste thickening applications. The principle of paste thickeners is that the compression zone is much deeper than on either high rate (HRT) or high compression (HCT) units; generally 3 metres or more. As the compression zone gets deeper, theunderflow density for a given flux rate (tph/m2) increases, as a result of two factors:1. Longer bed settling time. Settling flocs move relative to one another and release interstitial fluid when they are in compression. Increasing bed residence time achieves higher density underflow as more fluid is removed.2. The nett weight of the bed creates a compressive force on the settling flocs. This force increases with depth, so that the flocs at the bottom of the bed experience the highest compressive force. This represents the driving force to expel interstitial fluid and hence increase bed density."

Jan 1, 2005

By Otto Engel

"A multipurpose program for a hand-held programmable TJ-59 calculator and PC-100C printer facilitates the evaluation of various mineral processing tests and the calculation of mass and metal balances. Its application is demonstrated by some example problems. Detailed user instructions are given for each application.IntroductionThe program listed in Appendix I is written for a programmable Texas Instruments TI-591 PC-100C calculator I printer combination. The program is applicable for the evaluation of:1) screen analyses;2) flotation test s; and3) mass and metal balances.Each application is demonstrated by an example problem and corresponding detailed user instructions. The ""measured"" data in the examples are fictitious and do not represent a real operation.The steps in using the program are the same for each of the three types of application, viz.:1. Enter the number of product fractions and press ""A"".2. Enter the measured weights (0) of each fraction and press ""RIS"" each time. After the last fraction has been entered, the printer automatical1y displays the total weight.3. Press ""B"" to calculate the weight distribution (Y). Once ""B"" is pressed, the printer automatically displays the weight distribution of all fractions.4. If the accumulated weight distribution (EV) is also needed, press ""RIS"". The printer now displays these data. This step is optional and may be bypassed.5. Press ""2nd A"" to prepare for entering of the measured metal assay (M).6. Enter the measured metal assays of each fraction and press ""RIS"" each time. If analytical data exist for more than one metal, each data set has to be entered separately in one sequence.7. Press ""C"" to determine the ""calculated"" head assay (MA) of all fractions.8. Press ""RIS"" to calculate the metal distribution (R). Once ""RI S"" is pressed, the printer automatically displays the metal distribution of all fractions. This operation is optinal and may be bypassed if desired.9. Again press ""RIS"" to obtain the accumulated metal distribution (ER). This operation is optional and may be bypassed.10. Press ""D"" to calculate the gangue distribution in the concentrate (W). One ""D"" is pressed, the printer automatically displays the data for all fractions. This operation is optional and may be bypassed.11. Press ""RIS"" to obtain the accumulated gangue distribution (EW). This operation is optional and ma y be bypassed.12. For more than one metal, press ""E"" to clear the memory for storing the assays of the next. Then press ""2nd A"" and start entering the assays of the next metal as described previously (6 to 11). Steps 5 to 12 may be repeated as many times as desired."

Jan 1, 1982