Search Documents

By Yoginder P. Chugh

This paper discusses design of sprays systems for dust control around a continuous miner (CM) in about 4.2 m (14 ft.) high mining areas with about 1.0 m to 2.0 m (3-6 ft.) of out-of-seam dilution mining. The challenges included low air volumes and velocity at the end of the line curtain, dust produced from out-of-seam dilution rock being very fine with 50% of the particles less than 10 micron, poor capture of aerosol through scrubber suction inlets, dust escaping through the sides of the loading pan in mining high areas, overloading of dust-laden air in the wet-scrubber, and dust rollback toward workers. The challenges were resolved through CFD modeling of airflows; improved line curtain installation, redesign and varying the spatial locations of spray systems as compared to low mining height areas. Water sprays on CM is the primary engineering control for dust control in coal mining. In 2010, the authors developed several spray system concepts for dust control (Chugh, Patwardhan, Gurley, & Hirschi (2009), Chugh & Gurley (2009), Chugh 2012). These included increased contact time between dust particles and water droplets, improved potential for the dust aerosol to be sucked in through suction inlets, and reduced dust-roll back to the operators and workers. CFD modeling was used to understand airflow patterns around mining areas and to identify spatial locations for sprays to minimize dust exposure of CM operator (CMO), haulage unit operator (HUO), and workers downwind of the operating CM in the last open crosscut (LOXC). Face area ventilation plays a key role in dilution and removal of dust generated by mining operations. High mining heights and large pillar sizes associated with longwall mining reduce the air volume reaching the face area to achieve good dust dilution.

Aug 1, 2013

By M. H. ElMaghraby

This paper describes the development and validation of a strategy for vibration-based online detection of faults in a particular class of machinery commonly found in industry. This machinery is defined by two basic characteristics that preclude it from the application of standard online condition monitoring approaches. The first characteristic is that the machine is in a constant state of transient operation, thus making it difficult to differentiate between changes in transducer measurements that are due to variable duty and those that are due to machine malfunction or fault. The second characteristic is the fact that the machinery involves multiple sub systems that are subject to identical and simultaneous loading, operating environments and duty cycles. An example of such machinery is a system of multiple hydraulic pumps driving a common load. The monitoring strategy presented here employs an anomaly detection scheme together with methods of signal processing and feature extraction that exploit the parallel duty arrangements of this equipment. Preliminary data is collected from a pair or motor-gearbox assemblies used in a material haulage system in the mining industry. Testing and validation was performed on a mechatronic test bench with both healthy and faulted components. Experiments were carried out to investigate how various configurations of the system were able to detect different types of faults. The results indicate that this approach is effective and merits further investigation.

May 1, 2013

By F. G. Vetsch, F. A. Ronaghan

"Introduction1N THE FALL of 1951, Peace River Allied Fort St. John No. 1 well was drilled in Lsd. 1, Section 9 Township 83, Range 18, West of the 6th Meridian, on the flats of the north side of Peace river, six miles southeast of the village of Fort St. John, B.C. During this operation, non-commercial shows gas in three zones and of oil in one zone were obtained during the drill-stem tests. Further geological study indicated that this well was on the southeastern edge of the Fort St. St. John structure.Pacific Fort St. John No. 4, drilled shortly afterwards, obtained possible commercial gas flows on drill-stem test in five zones and thus encouraged development of what has become Canada's largest multizone gas field.In general, the productive horizons in this area possess fair per-meabilities and high porosities, a combination which provides for high reserves and moderate productivities. Development to date has therefore stressed experimental techniques in drilling and completion practice to provide high deliverability wells.Data and information of a specific nature apply, in all cases, to the pools in the Fort St. John structure."

Jan 1, 1954

By M. D. Evans

"Note: The views expressed herein are those of the author, not of the Government of CanadaThe mining industry has a significant opportunity to capitalize on past learnings to build better social relationships. The industry’s relationship with society is critical and under pressure. Rising levels of public opposition and social conflict are already having material impacts on operations around the world. The industry has an opportunity to shape the future direction of this social engagement, build public trust, and proactively respond to a material risk to operations, but first it needs to better understand the nature of the challenges and the urgency of addressing them.RÉSUMÉ L’industrie minière a actuellement une excellente occasion de tirer profit de ses expériences antérieures pour établir de meilleures relations sociales. Les relations entre l’industrie et la société sont critiques et elles subissent de grandes pressions. L’escalade de l’opposition par le public et les conflits sociaux ont déjà des impacts physiques sur les opérations partout à travers le monde. L’industrie a l’occasion de façonner la future direction de son engagement social, d’accroître la confiance du public et de répondre de manière proactive à un risque matériel aux exploitations, mais elle doit tout d’abord mieux comprendre la nature des défis et l’urgence de les traiter."

Jan 1, 2015

By C. H. Hopper, D. R. Derry, H. S. McGowan

"The property of Matachewan Consolidated Mines is in the Matachewan area on the west side of Montreal river. It lies in the western extension of the Kirkland Lake sedimentary belt. The first discovery of gold on the property was made by S. Otisse, in 1916. The property was taken over by Ventures, Limited, in 1933 and production commenced in late 1934. To date (December 31st, 1947) it has amounted to 2,308,800 tons, from which gold and silver to the value of $9,567,600 has been recovered. The mill is currently treating 650 tons of ore a day.GENERAL GEOLOGYThe deposits lie close to the south contact of a belt of sediments striking in a general east-west direction. The sediments, presumed to be of Timiskaming age, consist of light buff arkose and greywacke, containing small pebbles. The Keewatin volcanic rocks to the south are andesites or basalts with cuff and agglomerate bands developed especially near the contact with the sediments. The lavas and sediments are overlain by relatively flat-lying sediments of the Cobalt series to the south and west of the mine, but these later sediments are not involved in the mineralization under discussion. The Keewatin lavas and Timiskaming sediments are intruded by dykes and lenses of red syenite porphyry that have approximately the same strike and dip as the invaded rocks. Later diabase dykes, apparently post-ore, run in a north-south direction and cut all rocks except the Cobalt series.OREBODIESThe gold-bearing mineralization forms bodies of two different types: (1) Within the volcanic rocks irregular orebodies with limited vertical extent. These consist of a series of flat-dipping quartz stringers and adjacent lavas and /or cuffs fractured, bleached, and mineralized with pyrite and gold. They are higher grade than the second type (average about 0.16 oz. gold a ton) and formed the main source of ore for the first 5 years of production. They are described in more detail than can be given here in an article by C. H. Hopper (4). More recent work on deeper levels has failed so far to find orebodies of comparable grade, though low-grade mineralization of a similar type does occur on the projected rake of the main group of the 'basalt type' of orebodies."

Jan 1, 1954

By A. Klingberg, M. Svensson, N. Smolko Schwarzmayr

"Removal of silicates and carbonates from sedimentary phosphate ores by the use of new synthetic collector/formulations was investigated in a comparative study with traditionally used collector systems as references. In the direct carbonate flotation the new formulations showed higher efficiency, contributed to an improved balance of P2O5 recovery and P2O5 enrichment in the recovered material. Efficiency of the new formulations containing synthetic surfactants was 1.5–2 times better than potassium salt of fatty acid sulfonate based formulations that are traditionally used for that purpose. The new formulations also provided up to 7% increase in P2O5 recovery at the same P2O5 grade. The new synthetic collectors for removal of silicates showed extremely good selectivity towards silica bearing minerals. The selectivity factor for the flotation tests when new formulations were used was 32–52 and for the flotation tests with the traditional collectors: 20–32. The ratio between distribution of an amount of silicates (as SiO2) and distribution of phosphate in the froth (waste) is defined as the selectivity factor. The new formulations provided more than 2% decrease of the amount of SiO2 at the same P2O5 recovery.INTRODUCTIONPopulation growth and decrease of arable land are the main reasons for constant increase of consumption of apatite (phosphate ore) in the fertilization field (Lannefors, Gorochovceva, Klingberg, Lima, & Gustafsson, 2015). Fertilizers play a key role for farmers to produce more with less land. The phosphate component of the fertilizer is vital for producing healthy and large amount of crop. As a result the demand for phosphate rock is growing.The largest producers of phosphate rock are the Unites States, Morocco, Tunisia, China, Russia, and Brazil. The term “phosphate ore” includes all phosphate-bearing minerals and rocks, but only two of them are of industrial interest: apatite (igneous origin) and sedimentary phosphate (Peres, Araujo, El-Shall, Zhang, & Abdel-Khalek, 2007). The majority of the world’s phosphate deposits are of the sedimentary type. There are two different types of sedimentary phosphates: siliceous and carbonaceous which are categorized based on gangue minerals (such as quartz, carbonates, mica, and clay)."

Jan 1, 2016

By H. G. Stephenson, C. W. Gregory

"This article describes the methods used for pillar extraction in the Wilson Seam at Canmore Mines, Alberta. The Wilson Seam is extremely gassy and varies in thickness between 7 and 30 ft, with an average of 12 ft. The gradient varies from 5 to 30 degrees, with an average of 15 degrees. The seam was developed using Lee Norse miners to form pillars which the company intended to extract using the same machines. Before pillar extraction commenced, an abandoned and inaccessible mine 160 ft above the Wilson had to be drained of 360 million gallons of water. When this was done pillar extraction commenced. Conditions in the mine slowly deteriorated and after 6 months the decision to withdraw the continuous miners was taken. Slusher hoists were installed to replace the continuous miners, with the result that roof conditions and safety steadily improved."

Jan 1, 1972

By C. A. Pickles, D. K. Xia

"In the last few decades, microwave energy has been widely employed in food processing, rubber and plastics curing, and in ceramic sintering. Recently, the application of micro waves as an energy source in extractive metallurgy has received considerable attention from a number of researchers. During the period from the mid-1960s to about 1988, the majority of the research was focussed on the behaviour of materials in microwave radiation. These research activities will continue to be important, since fundamental data on the interaction of microwaves with materials are vital for the successful application of the technology. Since1990, a number of potential applications of microwave processing have been investigated.These include: pretreatment of ores and concentrates, leaching, reduction, preheating of refractories, heating of slags and waste treatment. In this paper, the interaction of micro -waves with materials of interest in extractive metallurgy are reviewed and potential applications are discussed.IntroductionMicrowaves were first used in 1946 for the heating of materials, shortly after radar equipment was invented during the second world war. It was evident that microwaves were very effective for heating water and the technology was quickly adopted for drying and cooking. Since the introduction of the first microwave oven by Raytheon in 1952, many millions of domestic microwave ovens have been sold annually (National Research Council,1994; Atomic Energy of Canada and Voss Associates Engineering, 1990).In extractive metallurgy, microwaves are in the early stages of development (National Research Council, 1994; Atomic Energy of Canada and Voss Associates, 1990; McGill and Walkiewicz, 1987; Bradhurst and Worner, 1990;Peng et al., 1993). However, there are several reasons for the growing interest in the use of this technology in the field of metals extraction. These include the following potential advantages of microwaves: (1) rapid and selective heating of materials; (2) reactions can be catalyzed because the heating occurs on a molecular or atomic level; (3) clean and controllable energy source; (4) the gas volume is reduced and the atmosphere can be controlled as there are no gaseous combustion products; (5) the material is heated internally in comparison to external heating with conventional methods; (6)the temperature of the refractory can be minimized; and (7) the working environment is improved."

Jan 1, 1997

By J. A. Allan

"The history of the development and application of controlled recirculation systems in U.K. collieries is traced and the theory behind such systems briefly examined. Specific applications for dealing with dust and dust/heat problems in headings, for which practical experience is currently available, are described. Consideration is given to the special features which these systems introduce in the underground situation and to the essential safeguards which are required for their safe use.IntroductionRecirculation of air is a commonly used technique in genera l ventilation and air conditioning practice, but has always been regarded with some suspicion for mining applications. This is perfectly understandable in view o f the hazardous conditions which can occur with dangerous forms of recirculation in mines. However, certain controlled recirculation techniques can offer advantages, particularly in the field s of dust and climate control in headings, provided that they are designed, Installed an d managed with full comprehension o f all aspects of the system and always bearing in mind that from the point of view of serious firedamp ignition risk, headings are potentially the most hazardous places in coal mines.BackgroundProbably the first recorded use of deliberate recirculation in British collieries was reported by Lawton in 1933. This researcher described trials, undertaken under the auspices of a national committee on ""The Control of Atmospheric Conditions in Hot and Deep Mines"", involving attempts to increase the velocity, and thereby the cooling power on hot faces, by means of simple recirculation systems using fans and ducts delivering recirculated air in the opposite direction to the normal face airflow. No significant cooling advantage was obtained and there is no subsequent record of this work being continued. During the discussion on this paper, there was considerable disbelief that fire damp percentages had not increased significantly when air was recirculated, but apparently no attempt was made to establish why this should be. It is of interest to note that J. Ivon Graham, one of the contributors, recommended that recirculation should be tried in stone headings for the control o f dust, as he believed that ""there may be scope for recirculation and filtration of the air under certain circumstances in such headings"". This idea was not developed for another forty years."

Jan 1, 1983

By R. Llewellyn

"Wear damage is responsible for very high maintenance costs and significant production losses in the oil sands industry of northern Alberta.It affects all areas of operations and involves a panoply of wear mechanisms from low stress sliding abrasion at extremely frigid temperatures during winter mining, to elevated temperature erosion/corrosion in processes where bitumen is converted to lighter hydrocarbon products.There is no universal panacea to defend against such diverse attack and a wide selection of resistant materials and systems is employed. These range from relatively soft rubbers which rely on their elastic properties for their protective capability, to some of the hardest ceramics and cermets which are currently available commercially.Details are presented of the characteristics and forms of the variety of wear materials being used and how they relate to the requirements of their areas of application. The review focuses on the practices followed at Syncrude Canada Ltd., which is the larger of the two commercial oil sands plants."

Jan 1, 1997

By P. C. Benedict

Introduction and Summary The Northern Empire mine is a mile east of Beardmore, and 100 miles northeast of Port Arthur, district of Thunder Bay, Ontario. Production started in March, 1934, and terminated in September, 1941. During this period, the mill treated 425,866 tons of ore, from which 153,103 ounces of gold were recovered. The lowest level from which ore was mined was the 1900, but considerable drifting was performed on the 2075 level and 800 feet on the 2415, the deepest level. The following description of the geology of the mine is recorded by the senior author but is based on the observations and complementary mapping of both authors. The vein strikes about N.72°E. and has an average dip of 80°S. (Figure 1). In stoped sections, the quartz averaged about two feet wide. On the 1725 level it was drifted on continuously for more than 7,000 feet, but in the mine as a whole practically no commercial ore was found beyond points 1,400 feet west and 1,800 feet east of the shaft. Conspicuous wall-rock alteration extended throughout this section but not much beyond its limits. There was some splitting of the vein and widening of the alteration halo on the lower levels. The average general colour of the quartz changes with depth. It may be generalized, from top to bottom, as light grey to dark grey to brownish. The brownish quartz first appeared near the bottom of the ore.

Jan 1, 1947

By L. H. Shang

The 319 Al-Si alloy is one of the most prominently used aluminium-based alloys in motor vehicle and engine applications, Microporosity present in 319 alloy castings reduces the load bearing capacity of the castings, The quantitative prediction of microporosity levels in Al-Si castings has been a subject of much interest for several years. In this research a new criteria function, tf 1,98 R13° (tf: local solidification time, R: cooling rate) was developed by multiple regression analyses, correlating thermal data from simulation studies to experimentally obtained microporosity values. This new criteria function gives a general prediction of microporosity in 319 Al-Si castings.

Jan 1, 2005

By Gaoming Wang

Outline 1. The Gangdese porphyry Cu-Mo belt 1.1 Regional geological background 1.2 Cu-Mo-bearing porphyries 1.3 Mineralization and alteration 2. Dating methods and results 2.1 Qulong porphyry 2.2 other porphyries 3. Geodynamic implications 4. Conclusions 5. Acknowledgements

May 1, 2004

By Claude Gosselin

En 1995, la Compagnie minière Québec Cartier a mis de l'avant un projet de recherche sur la modélisation de l'écoulement des gaz pour ses fours de frittage à l'usine de bouletage de Port-Cartier. Cette démarche s'inscrivait dans un large processus de collaboration avec l'Université Laval et le Consortium de Recherche Minérale (COREM). L'usine de bouletage possède deux fours de frittage d'une capacité moyenne de 600 tonnes/heure pour chacun des fours. Les fours de frittage sont des systèmes complexes d'échange de chaleur qui fonctionnent à contre-courant (le débit de boulettes versus les débits de gaz). Pour rencontrer les spécifications reliées aux propriétés mécaniques des boulettes, le processus de fabrication requiert des mesures et un contrôle des systèmes très précis. L'information fournie par plus de 70 capteurs (pression, température, puissance, vitesse, hauteur de lit, position de volet....) est utilisée pour manipuler une vitesse de grille, cinq ventilateurs et neuf zones de brûleurs. Malheureusement, les variables qui influencent fortement les mécanismes de frittage, c'est-à-dire les débits de gaz dans les différentes zones du four ainsi que la masse de boulettes qui circulent ne sont pas mesurées. Une méthode est donc proposée pour une estimation en ligne de ces variables. La méthode est basée sur un arrangement de 65 équations reliant pressions, températures et débits de gaz dans les conduites, les ventilateurs, les sections du lit et les fuites (Gosselin, 1998). Pour des raisons de simplification de cet article, seul un sous-système du four sera présenté. Les techniques de réconciliation des données reliées à la conservation de la matière et de l'énergie montrent que la mesure en ligne du débit de boulettes mène à l'estimation des débits de gaz et apporte des avantages intéressants pour le contrôle des variables stratégiques des fours.

May 1, 2001

By J. Ouellet

The authors participated in a study for a new mine shaft in Saskatchewan?s Athabasca Basin where ground freezing is desired to reduce water inflows. Constraints were imposed on the design in terms of permissible water leakage (less than 10 m3 / hour) inside the shaft. Since the shaft goes through highly permeable formations, water control measures had to be incorporated into the design. Ground freezing was selected as the most reliable and proven method for the sinking and a hydrostatic liner design was implemented. While exploring various technological options available for providing a fully hydrostatic liner, the authors came up with a new design concept that offers a more cost effective solution while meeting all the design constraints. The new liner concept is a composite design using concrete and a sprayed-on membrane system. A proof of concept program comprising laboratory testing and field testing was successfully implemented. This paper presents the innovative liner design, as well as the adapted sinking methodology, developed for this type of project. The new concept offers a new cost effective high performance hydrostatic mine shaft liner comparing favorably with traditional methods. RESUME: Les auteurs ont réalisé une étude pour un nouveau puits de mine dans le Bassin de l?Athabasca en Saskatchewan. Des limites sévères sont imposées sur le design en terme de volume d?infiltration d?eau acceptable (moins de 10 m3 / heure). Comme ce puits de mine traverse des formations très perméables la congélation des terrains a été sélectionnée, une méthode éprouvée et fiable. Un design hydrostatique a été choisi pour le revêtement du puits. Dans le processus de design, les différentes technologies disponibles ont été étudiées. Les auteurs ont développé un nouveau concept de revêtement composite offrant un rapport performance/prix plus avantageux que les technologies conventionnelles. Le nouveau design proposé est composé de béton et d?une membrane projetée. Un programme expérimental a été réalisé pour démontrer la faisabilité du concept. Cet article présente le nouveau concept ainsi que la méthodologie de fonçage de puits adaptée. Ce concept innovateur offre un revêtement hydrostatique performant à un cout avantageux par rapport aux techniques de construction utilisées jusqu'à maintenant.

Jun 1, 2012

By Jiuhua Xu, Shuiku Jia, Weiren Sun

"Abstract -The Jinqingding gold deposit, situated in the east Jiaodong Peninsula of Shandong province, is typical of the pyrite-quartz vein gold deposits in the Muping-Rushan gold belt of China . The gold deposit is controlled by a great NNE fracture zone and is composed of several lenticular orebodies within the fracture zone occurring in the Kunyushan granite massif. The Kunyushan granite massif was formed by the replacement of the Archean Jiaodong group.The main minerals associated with gold are pyrite, chalcopyrite, galena and sphalerite; the gangue minerals are dominated by quartz, sericite, microcline and calcite. The mineralizing event can be divided into four stages: (1) pyrite-quartz; (2) quartz-pyrite; (3) siderite-polymetallic sulfides; and (4) calcite-quartz. Gold occurs mainly as native gold and electrum in stage 1 and stage II. There are some evident differences between pyrite from major stages of gold mineralization and that from minor stages; these include differences in crystal forms, size and composition of fluid inclusions.Wallrock alterations consist of sericitization, silicification, pyritization and potash-feldspar alteration. Five alteration zones can be distinguished from unaltered granite (zone 0) to vein lodes (zone IV). Au and Ag increase rapidly from zone 0 to zone IV, Cu increases continuously, while Pb and Zn increase slowly. R-type geological factor analysis indicates that the Au, Ag, Cu, Pb and Zn bear a close relationship to wallrock alteration."

Jan 1, 1994

By C. Tasker

Introduction In the Early part of 1930 the Ontario Research Foundation was asked by the Minister of Mines, the Hon. Charles McCrea, K.C., M.P.P., to undertake a technical and economic investigation of the Northern Ontario lignite deposit. This investigation has been under way since June, 1930, and has necessitated considerable work at the deposit, in the laboratories of the Foundation, and at test plants in Europe. All the work has been carried out in active co-operation with the Provincial Department of Mines, the Deputy Minister, Mr. T. F. Sutherland, and several of his technical colleagues being associated with members of the staff of the Foundation on the Advisory Committee, which has met at frequent intervals to co-ordinate and direct the various lines of research. An interim report was made to the Minister of Mines by the Director of the Foundation, Dr. H. B. Speakman, at the end of December, 1932, and is at present under consideration by the Minister. This report deals with the extent and character of the deposit, the methods and costs of mining, and the methods and costs of processing raw lignite, the characteristics of certain lignite products, and the technology and economics of present fuel utilization by railways, industry, and domestic users in northern Ontario. It is not the purpose of the author to discuss in this paper either the geology of the deposit or the economics of the mining, processing, and utilization of lignite, but rather to deal briefly with some of the technical problems investigated by the Foundation during the study of the characteristics and methods of utilization of Northern Ontario lignite. Some mention, however, of the work carried out to define the extent of the deposit is a prerequisite to any discussion of the nature of the lignite.

Jan 1, 1933

By Torsten Zeller

Due to the increasing worldwide demand for raw materials and the resulting rise in commodity prices more expensive processing that is able to utilize complex ores becomes economically viable. This and increasing ecological awareness is why the interest in recycling and urban mining is steadily growing in Germany. In addition to that; landfills do also contain elements, which were not targeted over the period, when they were being accumulated. Examples are rare earths, indium, gallium, cadmium, arsenic, selenium and tellurium. Also copper, zinc and lead, the target components of ancient mining, can be obtained due to more effective processing and smelting technologies. Funding by the German Federal Ministry for Education and Research, entitled "r³ ? Strategic Metals and Minerals ? Innovative Technologies for Resource Efficiency" also indicates the high level of strategic interest. It is against this background that the research project "Exploitation of the Raw Material Potential of Mining and Metallurgical Tips in Respect of Sustainability as Exemplified in the West Harz Mountains (ROBEHA)" has been implemented. A major concern of this project is the possible transfer of results to landfills in other areas. Therefore the development of an expert system based on the innovative processing methods and a method manual for urban mining are the central components of the investigation. This will provide an important contribution to the cost optimization of ensuing urban mining projects. To ensure the success of landfill mining projects it is necessary to record the composition and quality of the deposits accurately. Also the environmental impact caused by landfill mining and changes in the natural and cultural landscape will be considered in a multicriteria evaluation method. Depending on their origin the tips are divided into the categories mining, processing, and smelting. The content of a landfill and thus the economic potential in terms of urban mining is dependent on the type and composition of the deposits (host rock, gangue, and ore mineral), the available processing and smelting technology, and the target components at the time of mining. Zinc, for example, was not been processed until the 19th century, when it gained attention as being material of economic importance. After such knowledge about a landfill is obtained the decision for further investigations can be made. For a total of 158 landfills in the Harz Mountains, both the volume and the approximate contents of copper, zinc, and lead has been estimated for the different types of tips within past research projects. Based on the prices of the London Metal Exchange (LME) and a euro/dollar exchange rate of 0.76 (as of 03/05/2012) and assuming a minimum density of ? ? 1.5 t/m³ a average value of 1.6 billion ? in copper, zinc, and lead can be obtained. Although only these three metals are considered in this first estimate, it demonstrates the potential of landfill mining and the need for further research. KEYWORDS Urban Mining,

Aug 1, 2013

By J. Stiksma, J. Dennett, R. Kalanchey, J. Ji, M. Collins, T. Chan, R. Berezowsky

A pilot plant campaign has been conducted by Sherritt Technologies in support of Eldorado Gold Corporation’s evaluation of pressure oxidation technology for the treatment of refractory gold concentrates from the Certej deposit in Romania. Four separate concentrates, containing 3.5 to 5.4 g/t Au, 13.0 to 14.5% S2- and 12.0 to 32.5 g/t Ag, were tested in the eight-day campaign. The major gold-bearing mineral was pyrite. Preliminary batch tests indicated that gold extraction from the oxidized concentrates in subsequent cyanide leaching was adversely affected by the presence of organic carbon in the pressure oxidation feed when chloride in solution was at an elevated level. As such, the process conditions that were tested during the pilot plant operation were selected to either counteract the negative impact of the organic carbon, or to deactivate it during pressure oxidation. Both process routes proved feasible, yielding gold extraction of 95 to 98% in cyanide leaching of the oxidized concentrates. Silver extraction was typically in the range of 80 to 90%, provided that the oxidized concentrates were also processed in a lime boil step prior to cyanide leaching.

Jan 1, 2014

By John Shirokoff, Ladan Khaksar

"Cyclic polarization technique and also potentiodynamic measurements were applied to study corrosion behavior of 13% chromium steels in chloride containing environment. Potentiodynamic measurements were performed at 25 and 75 °C with 0, 10 and 20 g/l NaCl in 0.01 M hydrochloric acid solution. At the same time, the significant pitting parameters such as corrosion potential (Ecorr), pitting potential (Epit), protection potential (Epro) and passive current (Ipass) of cyclic polarization curves with various NaCl concentration were analyzed and compared to describe the corrosion behavior of 13% chromium stainless steel. Surface measurement techniques such as SEM and EDS were used for morphology and analysis of corrosion products. The results showed that both temperature and Cl- concentration had significant effects on corrosion behavior of 13% chromium stainless steel in acidic solution.INTRODUCTION Of all the corrosion resistant alloys (CRA) used in oil and gas developments, martensitic stainless steels (MSS) are some of the most common ones these days. These steels not only have the advantages of normal steels: high strength, cost-effective, easy to manufacture, available in a wide variety of product forms, but they also have good CO2 corrosion resistance at higher temperatures as a result of their 11% minimum chromium content. One of the most common types of MSS used in the oil and gas industry is 13% chromium steel. NACE and API standards both reference several different varieties of 13% chromium steels for use in oil and gas projects(“Corrosion Resistant High Cr Steel for Oil and Gas Wells,” 2013). All types of 13% chromium steels have about 12 to 14% chromium and other minor alloying additions, and can be placed into two general groups: conventional and modified. Conventional 13% Cr steels (13Cr) are those most common in oil and gas, some of which are CA6NM (UNS J91150), AISI 410(UNS S41000), and AISI 420 (UNS S42000). These alloys have excellent corrosion resistance when compared to carbon steels up to about 300°F (150°C) and are used for a variety of wellhead, tubular, and downhole components however they have very limited resistance to cracking in H2S (Vallourec Group, 2015). Modified 13% Cr (M13Cr) steels came from the need for increased corrosion resistance at higher temperatures, increased H2S cracking resistance, and increased yield strength above 85 ksi (586 Mpa) primarily for tubular goods and other downhole equipment. These features were developed by taking a conventional 13Cr steel and adding nickel (Ni), molybdenum (Mo), copper (Cu), and other alloying elements. M13Cr provides better corrosion resistance than 13Cr up to about 350°F (177°C), yield strengths up to 110 ksi (758 Mpa), and also improved H2S cracking resistance(“Corrosion Resistant High Cr Steel for Oil and Gas Wells,” 2013)."

Jan 1, 2017