Search Documents

By Donald Lindell

Safety Share ?Dad receives fryer for Christmas 2009 and makes delicious sweet potato fries ?When the oil fryer was pushed back on the stove for cooling, the back edge comes into contact with the stove top controls, unknowingly activating the cooking element, family leaves kitchen. ?Faint smell of smoke from the melting plastic alerted the family; teenager arrives first and pulls the fryer forward causing oil to spill onto hot stove and burst into flames that reach the microwave ?Teen runs for sink to grab pan of water but is stopped by Dad ?Dad opens refrigerator, grabs baking soda and pours it on fire, extinguishing flames Lessons 1.DO NOT USE WATER ON GREASE FIRE 2.Where is the baking soda in your kitchen?

May 1, 2010

By R. Holmestad, M. Gazizov, S. Wenner, R. Kaibyshev, J. K. Sunde

"Mechanical properties and microstructure of an Al-4.7Cu-0.74Mg-0.51Si-0.48Mn-0.10Cr-0.09Ti-0.02Fe (wt. %) alloy subjected to various thermomechanical processing (TMP) have been investigated and compared to conventional ageing at 170°C (designated T6). Three TMP routes involving cold deformation of solution treated samples were tested. These were (i) 3%-stretching (T8-3%), (ii) equal-channel angular pressing (ECAP) to true strain (e) of ~1 (T8-1) and (iii) ECAP to e~2 (T8-2), all with subsequent ageing at 170°C for 0-96 h. At peak age conditions, both yield stress, ultimate tensile strength and elongation-to-fracture decreased for the T8-3% state as compared to the T6 condition. Intermediate ECAP (T8-1 and T8-2) lead to significant increase in maximum yield stress, ultimate tensile strength and elongation-to-fracture. The changes in mechanical properties were related to microstructure evolution, encompassing changes in grain sizes, dislocation densities, precipitate morphology and phase fractions, which were characterised using transmission electron microscopy. Relations between TMP, precipitation behavior and contributions to different strengthening mechanisms are evaluated.INTRODUCTION Al-Cu-Mg-Si alloys are widely used as structural materials in aerospace industry due to their attractive combination of high specific strength, good fracture toughness and enhanced creep resistance. These properties are largely due to the formation of a large number of nano-sized metastable precipitates during artificial ageing (Polmear, 2006; Eskin, 2003; Gazizov, Dubina, Zhemchuzhnikova, & Kaibyshev, 2015). The precipitation behaviour in these alloys is complicated and depends among other things on Cu concentration and the Mg:Si ratio (Wolverton, 2001; Chakrabarti, & Laughlin, 2004). In general, the precipitation sequence has been presented in a prior study (Eskin, 2003) as follows:"

Jan 1, 2018

By S. Forgeron

Presentation ? Introduction ? Canadian Underground Coal Mines ? Standardization of Geological Assessment ? Geomechanics Base-line Studies of Canadian Coal Mines ? Cape Breton Development Corporation Prince Mine ? Quinsam Coal Corporation ? 2 North and 4 South Mines ? Smoky River Coal Corporation 5B-4 Mine ? Conclusions and Baseline Comparison ? Figures

May 1, 2001

By Gordon L. Kidd

The object of this paper is to show the relations of the East Coulee coal area to the near-by Willow Creek, Wayne, Rosedale, and Drumheller areas, all being parts of the Drumheller field. The word ?area? is here used in a more local sense than that employed by Dr. J. A. Allan, whose. 'area' is rather comparable with the 'mining division' in British Columbia. I have drawn freely from the published information, particularly from Dr. Allan's report on the "Geology of Drumheller Coat Field, Alberta", and from Dr. E. Stansfield's paper on " A Chemical Survey of Alberta Coals", to whom thanks are due. The Drumheller field is served by branch lines of the two principal Canadian railways. The C.N.R. traverses the district by its Goose Lake line from Calgary to Saskatoon; and the C.P.R. by a line from Calgary to Acme and then southeasterly to Drumheller, where it effects a junction with the C.N.R., over which the C.P.R. has running rights as far as Rosedale. From Rosedale, a joint line built during the summer of 1928 extends about forty miles down the Red Deer river to the mouth of Bull Pond creek. From that point the C.P .R. turns more southerly to connect with the Bassano-Empress line. The C.N.R., it is expected, will eventually proceed eastward to connect with a transcontinental line. The joint line from Rosedale down the Red Deer river opened up the Willow Creek and East Coulee areas.

Jan 1, 1929

By D. Satish Kumar, D. Mazumdar

"95% bulk mixing times in three different size water model ladles of a 140 T cylindrical shaped , dual plug ( located diametrically opposite at mid bath radius position) stirred, industrial ladle were determined experimentally with and without an upper buoyant phase. Based on dimensional analysis and a regression of the experimental data and, it was shown that in the inertial and gravitational force dominated flow regimes, 95% bulk mixing times for a slag-less situation can be described via:[equation]Parallel to this, a large number of experiments were also carried out in one of the water models (D=0.30m) to quantify the influence of an upper buoyant phase on mixing. These indicated that mixing time, operating variables and thermo-physical properties of the upper phase liquid can be correlated via a dimensionless relationship of the type:[equation]in which, Q is the ambient gas flow rate, L is the depth of liquid , (AL) is the slag layer thickness and 6 and t are respectively the surface tension and viscosity of the upper phase fluid The dimensional analysis, regression of experimental data as well as the adequacy of the proposed correlations are discussed in the text."

Jan 1, 2004

By M. E. Hurst

SINCE 1934 there has been a marked revival of interest in the Porcupine district, especially in the eastern portion of the area, where exploration on the property of Pamour Gold Mines has indicated the presence of extensive gold-bearing deposits. Owing to the prevalence of overburden and the limited amount of exploratory work that has been done, little information is available as yet concerning the distribution and structural relationships of the rocks in the area to the east of Porcupine lake. In order to throw some light on the structural conditions in this section, a brief discussion of the sequence and character of the formations in the better known, producing section of the camp has been included. It should be emphasized that this paper is a preliminary study and that, consequently, the conclusions expressed should not be regarded as final. The writer wishes to acknowledge his indebtedness to P. C. Benedict, whose study of the geological relationships on the Foley-O'Brien property has made possible a fuller understanding of the structure in the central portion of the area. The writer also wishes to express his appreciation of the information and facilities placed at his disposal by R. M. Macaulay and C. D. Stevenson, of Pamour Gold Mines, and by A. Bell, of Noranda Mines, Limited.

Jan 1, 1936

By H. Chaouki

The aim of this work is to simulate the forming process of a green anode. For this purpose, a nonlinear compressible viscoelastic constitutive law is presented. The concept of natural reference configuration is considered. Within an isothermal thermodynamic framework, a Helmholtz free energy is proposed to take into account the nonlinear compressible deformation process occurring between natural reference configuration and current configuration. A dissipation potential is introduced in order to characterize the irreversible aspect of compaction process. Thus, the constitutive law is formulated through two equations: 1) an expression of Cauchy stress tensor and 2) a differential equation characterizing the evolution of the natural reference configuration. Material parameters are assumed to be a function of the bulk density. This allows capturing the micro-mechanical phenomena within the chosen macroscopic approach. An experimental study based on compaction tests is carried out in order to characterize the mechanical behaviour of the anode paste. A user's material VUMAT subroutine for finite element dynamic explicit analysis has been developed and implemented in the ABAQUS commercial software. To evaluate the model predictive capability, numerical simulations of the compaction forming process of anode paste were performed. Simulation results show that the constitutive law predicts the experimental trends and gives interesting physical responses. This constitutes a first step toward making a benchmark with experimental results on the forming process of anode paste.

Jan 1, 2011

By F. Logsch, H. Pempel, J. Markowski, P. Ay

"Due to the European Directive 2000/53/EC on end-of-life-vehicles, from 2015 on more than 95% of car materials have to be recycled. In order to recycle the materials back into the economic cycle, it is necessary to produce products with high quality and purity.Plastic components in cars, which are coated with metals by vapour deposition or electroplating, have a wide circulation (e.g., as cladding panel or trim strip for interiors and exteriors). In the end-of-lifevehicle recycling process, these plastic-metal composites are not considered in usual technologies (car shredder) and are not separated from Automotive Shredder Residue. These parts can be separated by optical or HF-detection sorting and then introduced to a specific treatment.Experiments with a specially developed bioleaching configuration showed that the thin coatings, which consist mainly of copper, nickel and chromium, can be removed efficiently from the polymer base materials by a bioleaching solution with Acidothiobacillus ferrooxidans as a leaching agent. The solution used was produced in special fermenters with a 9K-nutrient salt media. During the bioleaching process at 35°C maximum temperature, most of the copper is dissolved and the other metals accumulate as metal sludge. The bacterial cultures based on A. ferrooxidans are robust and resilient.After a 48-hour bioleaching period while the composites were stirred regularly with ventilation, the plastic particles were completely free from metallic coatings. The metal components are separated for further use: undissolved components (mainly Ni and Cr) are separated by decantation of the solution; dissolved copper recovey is carried out by cementation of copper. The cementated solid contains ~98% Cu, along with small amounts of other metals.With the bioleaching process, good separation and re-utilization of the metallic coatings is possible. The cleaned plastic parts were prepared by compounding for new applications with injectionmoulding."

Jan 1, 2016

By V. F. Kozyrev, L. B. Tsymbulov, L. Sh. Tsemekhman, A. N. Golov

Gipronickel Institute, JS has developed a new process and equipment for melting copper raw material in a two-zone Vaniukov furnace resulting in the production of white matte and low-grade slag in terms of copper content. Tests on processing copper nickelcontaining ore from Norilsk (Cu - 17 %), Ni - 3 %) were conducted in Vaniukov pilot furnace (total area 11.4m2) of Severonickel Combine. The amount of the processed material was about 11 thousand tons. Principal results of pilot testing are presented.

Jan 1, 2007

By Charles Camsell

At the Annual General Meeting of the Institute in 1924. I endeavoured to present the position held by the mineral industries in the commercial life of this country. The facts and figures were presented at that time in a detached way. Since then, however, I have made some attempt to analyze them in order to determine the causes for that position and to draw some conclusions as to the future of the mining industry. As everyone knows, our trade figures are very often used in political discussion, especially in discussion of tariff policy. It would be entirely out of order for me to say anything touching the tariff issue and I want to have it clearly understood that, in my opinion, the material I am about to present contains not a single statement or conclusion which anyone would be warranted in using as an argument for either a lower or a higher tariff or for tariff changes of any kind. As a starting point, let me re-state, very sketchily, Canada's general situation in external trade. In the last calendar year, 1924, we sold Canadian merchandise of all kinds to other countries to the value of $1,045,000,000 in round figures. Our purchases abroad reached about $893,000,000. Thus our sales exceeded our purchases by roughly $152,000,000. In other words, we had what is known as a 'favourable balance of trade' - one of the biggest favourable balances we have ever had in our history. The proceeds of our sales of Canadian products enabled us to meet the bills for all our purchases of foreign commodities and, in addition, placed a large surplus to our credit with which to offset our interest charges and other obligations abroad.

Jan 1, 1925

By Joseph Carlston

With environmental regulations continuing to restrict the discharge of phosphorus from wastewater treatment facilities, traditional methods of phosphorus removal are proving inadequate. To achieve the phosphorus control necessary, a new coagulant used for phosphorus removal, cerium chloride, has been studied in several municipal and industrial wastewater treatment facilities that must meet a phosphorus discharge limit of 0.5 mg/L or lower. These studies demonstrated the high phosphorus removal capabilities of cerium chloride, with the results illustrating the ability for cerium chloride to reduce phosphorus to low concentrations in the effluent using a lower volume of product as compared to traditional coagulants, such as ferric chloride. This reduction is due to the unique ability of cerium chloride to remove phosphorus as cerium phosphate, whereas iron- and aluminum-based coagulants rely on adsorption and co-precipitation.

Jan 1, 2014

By R. Burns, A. I. A. Salama, M. W. Mikhail

"Large amounts of oil sand tailings are produced in the Fort McMurray area, including sand, clays, and misplaced bitumen. The objective of the present study (as part of the overall engineered tailings program) is to select and evaluate the role of hydrocyclones in removing most of the solids from the tailings slurry and producing an underflow product containing about 75% solids.Multistage cyclones were evaluated in pilot plant tests. Slurry feeds with different percents solids and increasing ratios of superfines (–44 µm) were used in testing multistage cyclone circuits. A two-stage Linatex separator circuit gave high recovery to the underflow of 98.8% to 99.6% by mass with the desired high solids content in the underflow of 73% to 75% by mass. Changes in feed solids content (20% to 50%) had little or no influence on cyclone underflow recovery and solids content. The keys to achieving such results were the apex control mechanism and operation at relatively low feed pressure (<60 kPa for 23 cm F cyclone) when the feed solids content was high. Increasing superfines above 7% by mass in the feed resulted in a significant reduction in the recovery to the underflow, probably due to the heavy medium generated by excessive amounts of clays in the cyclone. Pilot plant results were better than those predicted by available cyclone simulation models in terms of recovery and solids concentration in the underflow.Increasing cyclone diameter from 23 cm for the Linatex separator to 51 cm for the Krebs cyclone appears to have little or no effect on size cutpoint."

Jan 1, 1997

By Steven D. Botts

The Antamina project, owned by BHP Billiton Plc, Mitsubishi Corporation, Noranda Inc., and Teck Cominco Ltd. , is a $2.3 billion copper/zinc project, located in the Ancash Department in Perú. The project consists of an open pit mine, a 70,000 ton per day concentrator, a 302 Km. long concentrate pipeline, port facilities, a new access road, power line, and town site. The project is designed to produce up to 1.5 million tonnes per year of copper and zinc concentrates over a 23-year project life, and will be the third largest producer of zinc and the seventh largest producer of copper in the world. This mega project is the largest mining investment in the country and, during its construction stage, was the most important construction project worldwide. On May 28th, 2001, Antamina commenced testing operations and four months later, it reached commercial production. Antamina was officially inaugurated on November 14th, 2001 by Peruvian president Alejandro Toledo. The construction stage of the project generated 8,000 direct jobs, with a peak of 10,000 employees, and 30,000 indirect jobs. The permanent workforce consists of approximately 1650 employees, the vast majority of which are Peruvian Nationals; around 30% of whom came from the department of Ancash where the deposit is located. Approximately 5,800 indirect jobs will be generated from the project. Independent sources state that Antamina will increase the Peruvian mining exports by 30% and Peruvian GDP by 1.4% within its first year of full operation in 2002. Since winning the privatization bid for the project in 1996, the company has implemented a successful approach to community development and environmental protection based on sustainable development principals. Throughout the development of the project, a number of initiatives have been undertaken to ensure full involvement of the local populations in community development activities and the company?s environmental program. Due to its size, difficult logistics, cultural considerations and financial aspects, the project has faced a number of unique challenges in the area of environmental protection and management of community interaction. Antamina has been innovative in its approach to these issues, and as a result, has set new standards in Perú for environmental and community management, and sustainable development.

May 1, 2002

By Georges Houlachi, Akram Alfantazi, Maysam Mohammadi

Manganese ions in zinc electrowinning electrolytes form a protective MnO2 layer that ultimately decreases Pb contamination in the zinc product. In this study, the effect of dissolved Mn2+ on the electrochemical performance of Pb, Pb-Ca and composite Pb-MnO2 anodes was investigated. The properties of the MnO2 layer formed on these anodes were studied and compared. Potentiodynamic polarization and cyclic voltammetry experiments were performed in 180 g L-1 sulphuric acid to study the electrochemical reactions occurring on the anodes. The anodes were subjected to galvanostatic polarization at 50 mA cm-2. The morphology and uniformity of the MnO2 layer on the anodes were examined using scanning electron microscopy (SEM). Experimental results revealed that the MnO2 layer formed on the composite anode was more compact and uniform compared to that formed on the Pb and Pb-Ca anode. It was also observed that the cell mud formation rate, and consequently manganese ions consumption, depended on the anode type. Although initial formation of the MnO2 layer decreased the oxygen evolution overpotential, its growth might negatively affect electrocatalytic activity of the anodes.

Jan 1, 2014

By J. Costigan, C. Corless

In 1997, damage as a result of Castrol R40 entering the INCO pressure carbonyl plant carrier gas stream was becoming increasingly severe. The oil in the gas stream was adversely affecting both equipment availability and process control resulting in rising unit costs. The main source of the Castrol R40 was determined to be the carrier gas and low pressure gas blowers. Plant personnel initiated a plan to prevent the Castrol R40 from entering the carrier gas stream by replacing the mechanical shaft seals with Ferrofluidics seals on these blowers. The following paper details a brief case history of the Castrol R40 in the carrier gas including impact on the plant. This will be followed by a technical discussion of the new sealing arrangement that was developed by plant personnel, Roots Blower and Ferrofluidics. Lastly, this paper will update the status of the blower upgrade project and document the results to date.

Jan 1, 2000

By Hang Zhao, Xinping Li, Pingan Wu, Yi Luo

The deep-buried rock surrounding the Jinping II Hydro-power Station was taken as the engineering background. Using model specimens of classified rock materials to simulate fractured rock mass under high in-situ stress conditions, the test about acoustic propagation law on single fracture model of specimen under different pressures and different angles were carried out. The variation of p-wave velocity in fractured rock mass and axial stress-strain relationship in the whole test procedure was also studied. Based on damage mechanics principle and the acoustic wave propagation in cracked rock mass, comparative study on damage constitutive relation of fractured rock mass under high in-situ stress in consideration of equivalent strain and equivalent energy was performed. As the results showed, with the change of axial stress level under constant confining pressure, the change in wave velocity can be divided into three stages: slow increase (small variation in amplitude), rapid reduce (large variation in amplitude ) and accelerate reduction. When the confining pressure is constant, the maximum p-wave velocity and the peak strength of specimens increases with the decrease of the crack angle. When the crack angle is constant, the maximum p-wave velocity and the peak strength of specimens increases with the increase of confining pressure.It is identified that the theoretical calculation results of constitutive relation about elasto-plastic damage model containing variable wave velocity in the fractured rock mass is consistent with the model test results.Therefore,the constitutive relation can provide reasonable suggestions for engineering practice.

Jan 1, 2015

By C. J. Li, J. L. Feng

In the present study we focuses on developing the poroelasticity model that deals with adsorptioninduced permeability change mostly occurred in porous media constituted several phases such as coal. The underlying pressure induced by adsorption is obtained by Virial expansion form, which is substantially founded on statistical physics. The corresponding thermodynamic pressure applying on the pore surface is then used to detail the pore pressure and further to evaluate the macroscopic volumetric strain and the porosity. In the process of physical adsorption, the adsorbed phase is in thermodynamic equilibrium with the gas phase regardless of pore size, and the corresponding chemical potentials are all equal. The relationship between surface strain and volumetric strain is derived under infinitesimal deformation conditions to gain an explicit formulation of pore surface area with respect to volumetric strain and porosity. After the formulation of surface stress modified by the Langmuir isothermal adsorption is derived, the differential micromechanical constitutive equations of porous media are obtained. By supposing that the ratio of current permeability to initial is equal to the cubic ratio of current porosity to initial porosity, the differential equations for permeability change is consequently derived. The numerical simulations by the present model for permeability change of coal induced by adsorption of CO2 and CH4, respectively, are presented under confined stress conditions. The predictions from the model are good in agreement with the experimental data of sorption-induced permeability change of coals in the literature.

Jan 1, 2015

By Xiang Li, Xibing Li

It is paramount that the stability of rock slopes be correctly accounted for under diverse operating and environmental conditions. Owing to different sources of uncertainty entailed in such stability problems, conventional deterministic approach through the calculation of a factor of safety (FOS) cannot reflect quantified uncertainties explicitly and sufficiently. Thus it is highly desirable to invoke the reliability approach to consider uncertainties in a systematic manner. Nowadays, the current design standards have an increasing tendency to ensure rock slope stability by pre-defining a target reliability index (or target probability of failure), viz., the reliability level of a rock slope is pre-set as a target to be satisfied. In such a situation and considering the fact that the FOS used as an indicator of slope performance still has a very wide acceptance, we focus on proposing an inverse-reliability-based methodology which aims at developing a two-fold indicator strategy, i.e., using the FOS and reliability together to deal with slope stability problems. The basic idea behind it is to utilize a so-called inverse first-order reliability method (IFORM) to directly calibrate the FOS provided the target reliability index has been given. In this way, the calibration scheme relating the FOS can be rationally done by not only incorporating uncertainties, but also satisfying a desired level of the prescribed reliability. Based on this, to make the IFORM computationally feasible and also reduce its computational cost, we introduce the response surface method (RSM) to generate a surrogate for the FOS-based limit state function (LSF), considering the lengthy and complicated form of the FOS in some recognized methods (e.g., within the framework of limit equilibrium). Distinguished from the existing RSMs that potential inadequacies may arise, we present an RSM based on a hybrid approach combining support vector machine (SVM; used as a regression technique) and uniform design (UD; pertaining to experimental design). Using a representative example of rock slope stability problem, we demonstrate the feasibility and validity of the developed methodology, during which the associated sensitivity study and further discussion are also performed. By dint of such a methodology, we can establish a link between the conventional deterministic approach and the reliability approach, where a logical and realistic framework is provided, for cases achieving the specified reliability, to assist in selecting the FOS which remains adequate for rock slope stability even in the face of uncertainty.

Jan 1, 2015

By F. J. Hrach, S. A. Gasiorowski, J. D. Bittner

"Separation Technologies, LLC (ST) has developed a processing system based on triboelectric charging and electrostatic separation that provides the mineral processing industry a means to beneficiate fine materials with an entirely dry technology. In contrast to the other available electrostatic separation processes that are typically limited to particles greater than 75 µm in size, the ST belt separator is ideally suited for separation of very fine (<1 µm) to moderately coarse (500 µm) materials with very high throughputs.. The technology has been also successfully applied to the beneficiation of a variety of minerals including calcium carbonates, talc, and potash. TECHNOLOGY OVERVIEWThe ST separator utilizes electrical charge differences between materials produced by surface contact or triboelectric charging. When two materials are in contact, material with a higher affinity for electrons gains electrons and thus charges negative, while material with lower electron affinity charges positive. This contact exchange of charge is universally observed for all materials, at times causing electrostatic nuisances that are a problem in some industries. Electron affinity is dependent on the chemical composition of the particle surface and will result in substantial differential charging of materials in a mixture of discrete particles of different composition.In the ST separator (Figures 1 and 2), material is fed into the thin gap 0.9 – 1.5 cm (0.35 -0.6 in.) between two parallel planar electrodes. The particles are triboelectrically charged by interparticle contact. For example, in the case of coal combustion fly ash, a mixture of carbon particles and mineral particles, the positively charged carbon and the negatively charged mineral are attracted to opposite electrodes. The particles are then swept up by a continuous moving open-mesh belt and conveyed in opposite directions. The belt moves the particles adjacent to each electrode toward opposite ends of the separator. The electric field need only move the particles a tiny fraction of a centimeter to move a particle from a left-moving to a right-moving stream. The counter current flow of the separating particles and continual triboelectric charging by carbon-mineral collisions provides for a multistage separation and results in excellent purity and recovery in a single-pass unit. The high belt speed also enables very high throughputs, up to 40 tonnes per hour on a single separator. By controlling various process parameters, such as belt speed, feed point, electrode gap and feed rate, the ST process produces low carbon fly ash at carbon contents of 2 % ± 0.5% from feed fly ashes ranging in carbon from 4% to over 30%."

Jan 1, 2012

By H. C. Cooke

"The Eustis mine, which was discovered in 1865, lies about 6 miles southwest of the city of Sherbrooke, Quebec, in lots 2, 3, and 4, range 9, Ascot tp. The mine was operated almost continuously from 1865 to 1937, under vanous owners.The ore was pyrite with varying amounts of chalcopyrite, a small amount of zinc blende and galena, and a low content in gold and silver. Parts of it ran quite high in copper, but the mine average would probably have been between 3 and 4 per cent. The high percentage of pyrite made it profitable to separate the ore into a copper concentrate and a pyrite concentrate. The latter was shipped away for manufacturing sulphuric acid, or was treated in a plant erected in 1887 at Capelton by the Nichols Chemical Company.The ore is a replacement of mica schist, which in turn was formed by the shearing of rhyolite flows. Ore also replaces the 'green rock', a term locally applied to carbonatized mica schists. The ore contained numerous 'horses' and smaller fragments of country rock, in all stages of replacement, ranging from those whose character was quite distinct to those whose ancestry could only be detected by an indefinite banding preserved in the sulphides."

Jan 1, 1954