Search Documents

By H. J. McQueen

Pressure welding is a solid state joining technique that depends on bringing the parts into sufficiently close contact that inter-atomic bonds are achieved. Pressing is more effective at elevated temperatures where plastic flow causes the asperities to collapse; improved application conditions are derived from hot-work research to clarify temperature and strain rate dependence of hot strength and ductility. The substructure evolution systematically studied in hot working to determine dynamic recovery or recrystallization is applied to clarifying that developed in welding. The various processes are affected differently by work-piece geometry and final shape requirements. In addition to pre-cleaning of the surfaces, the plastic flow helps disperse the remaining oxide layers as was originally exemplified in blacksmith hot forging of layered sword blades and in bellldie welding of wrought iron tubes. The presentation critically compares the utility for various materials and configurations of simple pressure, ultrasonic application, diffusion, explosive, rotary and linear friction and friction-stir processes. Diffusion bonding (primarily Ti) with light cleaning, low pressure, little distortion in protective furnace atmosphere contrasts strongly with the heavy upsetting in friction welding, or complex alloy mingling and substructure variations in friction stir joints.

Jan 1, 2011

By J. E. Williamson

Introduction 1. Factors on Which the Design of the Roaster Plant was Based The roasting operation at Lake Shore, it was realized from the outset, would be profitable only if costs and losses could be reduced to a low figure. It was absolutely imperative that the operation should be self roasting over the whole range of tonnages and sulphur grades which might obtain during the life of the mine. The roasting operation could not bear the cost in fuel and labour of even a partially fired roast. To meet this requirement, it was necessary to resort to additional insulation in the construction of the roaster and to provide a more flexible means of rabble cooling than the conventional water jacket (see p. 31). A second basic consideration was that of handling a wet, putty-like concentrate. The operating costs of a drier ruled out the possibility of drying the charge before feeding it to the roaster. Moreover, the dusting which would result from charging a dry product virtually all -40 micron (325 mesh) in size would seriously handicap the use of a dryer. Dust lubrication (p. 3S) due to the back-mixing action of the Edwards rabbles, and the use of a Sullivan slapper ( p. 27) on the concentrate filter, completely solved the problem of handling the roast feed. The third consideration was the reduction of dusting to a sufficiently low point that a Cottrell or other dust collecting system was unnecessary. The Edwards roaster when properly supervised, it is believed, can be operated to give the minimum possible dusting. At Lake Shore, the evidence has been that less than 1 per cent dusting occurs at any time and that the greater part of the dust produced is recovered either in the spray tower or in the dust chambers.

Jan 1, 1947

By Alice H. Zhu

Belt conveyors are widely used in materials handling industries. The bulk materials which can be transported include ores, coal, earth, grain, limestone, wood chips, fertilizer components such as potash and many others. Along with the new technology development and enhanced industrial automation requirements, belt conveyor instrumentation has also been modernized to improve conveyor availability and performance. Traditionally, belt conveyors are equipped with emergency pull cord switches to shut the conveyor down, misalignment switches to signal the belt offline condition, speed sensors to detect the belt slippage, and level switches to prevent material plugging in the discharge chute. Belt rip detectors are also normally provided for long belt conveyors. As a rule, equipment condition monitoring is not automated at most operating facilities, but is performed manually by maintenance staff via time-based surveillance. The new generation of condition monitoring instrumentation and control equipment can be successfully utilized to design a reliable, cost-effective, and centralized monitoring system, capable of monitoring a wide variety of mechanical equipment. The implementation of the condition monitoring automated system can provide continual monitoring of the plant equipment to ensure safe operation of the equipment to its required capacity. Any abnormal behavior of the motors, gear reducers and pulleys can be analyzed, alarmed, and recorded immediately, so problems can be detected and resolved before critical components failure. Therefore, the current trend is to provide the belt conveyors with condition monitoring system in addition to the traditional instrumentation, where temperature probes and vibration sensors can be installed on motors, gear reducers and all pulleys. Another innovative development is a three-in-one type belt rip detector which combines laser, tray and cord type detection together to ensure a prompt belt tear indication. The purpose of this paper is to present the latest development of belt conveyor instrumentation and introduce the application of newly developed instruments.

Nov 1, 2011

By A. R. Miller, M. C. Bétournay, D. L. Barnes

"A number of successful proof-of-concept projects have been carried out to replace conventional power application, such as diesel and rechargeable batteries, in underground mine vehicles. This has led to the development and testing of the world’s first fuel cell production vehicle, a mine locomotive. A fuel cell loader is being built and tested.This paper provides an insight into other projects that are being carried out. Some are related to further underground applications, and some to further research, such as refueling options, power plant durability, and vehicle automation.Also outlined is an evaluation of the overall mining applications and advantages this technology can bring to underground mining, including the facilitation of automation and tele-remote operation."

Jan 1, 2003

By John C. Taylor

A resource document, prepared for the Royal Commission on the Health and Safety of Workers in Mines, which outlines aspects of occupational health and safety in the Canadian metallurgical industry has been expanded to provide examples of some practical solutions. General process descriptions are provided in conjunction with some of the major potential hazards associated with each step. Emissions to the working environment, particularly around converters, are discussed. Newer metallurgical processes, the role of automation and other advances in the metallurgical industry are described with respect to their impact on the work place. The role of staff and unit employees in providing safe working conditions in the complex metallurgical plant of today is outlined and the need for close cooperation within the human sector emphasized. The technology is available and is being applied to integrate the complex process requirements with realistic regulations to control emissions and provide a safe, healthy environment in metallurgical plants.

Jan 1, 1978

By C. H. Lee, K. Adham, D. Lemieux, J. P. Mai, A. M. S. Hussein, S. Francey

Copper concentrates contain an increasing amount of arsenic, as the older sources of cleaner ores are depleted. At the same time, the market-determined price penalties on arsenic rich concentrates are rising due to limited arsenic treatment capacity at smelters and increasingly stringent environmental emissions limits, necessitating arsenic removal from the copper concentrates. Heating the concentrate to about 700°C can remove significant amounts of arsenic (as elemental and/or sulfide); however, it is important to achieve that removal economically and with due consideration to post-roasting arsenic (toxic waste) treatment. A comparison is made among different roasting options (kilns, multi-hearths and fluid beds) to qualify their potential application to arsenic roasting of copper concentrates. Both direct and indirect methods of heating as well as inert, air and oxygen atmosphere options are considered. Technology comparisons are made with respect to the roaster’s operation, its off-gas treatment and arsenic stabilization. INTRODUCTION In the last twenty years, the arsenic content in globally produced copper concentrates have risen steadily due to the depletion of cleaner ores and the increase in complex concentrate production. Smelter contracts typically limit arsenic to less than 0.5wt%, with a penalty paid per unit of additional arsenic and other contaminants such as antimony. While penalties can vary, they can be on the order of $70/dry metric tonne of concentrate per 1% of arsenic. Strategies used by miners to avoid the price penalties have been to blend clean and complex concentrates, and to remove arsenic from complex concentrates to achieve smelter limits. Arsenic can be removed from copper concentrates by the heat-induced decomposition of the predominant enargite mineral (Cu3AsS4) at ~700°C. Roasting at such elevated temperature is a commercially proven option, but still suffers from process, cost and environmental challenges. After roasting, the released arsenic sulfide fumes can be separated from most of the entrained concentrate dust in cyclones. Then, the As2S3 laden off-gas can be oxidized to generate a still volatile oxide (As2O3), which can be further separated from the residual concentrate dust in a hot electrostatic separator. Next, the off-gas can be cooled with air or water, to either deposit the arsenic oxide in a dry or dissolved state. Dissolved arsenic acid can be oxidized to As(V) and reacted with iron to yield a stabilized ferrihydrite precipitate or scorodite that can be safely disposed. In the case of dry arsenic trioxide, it can be mixed with reactants (e.g. iron) and fluxes before thermal stabilization in a glass matrix, thus eliminating the need for costly oxidation.

Jan 1, 2019

By I. Stanoev, V. S. Stoilov, I. Gradinarov, E. D. Visariev, I. A. Bonchev, Aurubis Bulgaria

"Aurubis is the leading integrated copper group and the world’s largest copper recycler. In Copper smelter Aurubis Bulgaria (Pirdop), the residual copper in the slags from Flash furnace and Converters is recovered by flotation. The slag processing comprises: pit cooling, crushing, two stages grinding (autogenous and ball) and flotation. The copper concentrate is thickened and then is filtrated by vacuum disk filter. The thickener overflow is sent to settler for additional clarification. A resent throughput increase resulted in higher solid content in the thickener overflow due to insufficient thickener area. Different scenarios to overcome the issue were evaluated (new thickener, reagents and reconstruction). An increase of the thickening area by installation of lamella modules was chosen as the most promising option. Three lamella modules (1 m3 each) were installed in conventional thickener for the test. Number of sampling campaigns was done to evaluate the effect on solid content in overflow. Parameters of the dewatering cycle were collected during sampling campaign. The products grain size distribution was defined - thickener feed, thickener overflow with and without lamella. The thickener overflow with lamella modules has 2.12 g/L less solid content. The decrease was 71.8%. According to the tests results, the whole conventional thickener was reconstructed with lamella modules. The thickener area was increased by more than 400 m2.INTRODUCTIONIn Copper smelter Aurubis Bulgaria, the copper in slag from the Flash furnace and the Converters is recovered by flotation. The scheme of slag processing is crushing, two stage grinding (autogenous and ball) and flotation. Till 2010 the grinding cycle in the plant was in two stages: the first stage was AG Mill 70×23 working with a classifier and the second stage was ball mill 3.6/5.5 working with a hydrocyclone. In 2010 a new AG Mill 65×78 with hydrocyclone was put in operation in order to increase throughput of the plant. The second stage of the grinding cycle was not changed."

Jan 1, 2016

By Côme Carbonneau

The ten -year case history of La Société Québécoise d'Exploration Minière (SOQUEM) is reviewed under the headings of the company's raison d'être, objectives, policies, structure and final goal. A brief analysis of its past operations is presented: aborted efforts, findings and developments. A projection is made of the future earnings, in terms of estimated present value, of its three main discoveries - Louvem , Niobec and Selim.

Jan 1, 1978

By Claude Dufresne

The technical development of the niobium-bearing products is to a great extent influenced by the striving of the respective industries to maintain or strengthen their positions in all fields of application against competing materials. South East Asia, China, Eastern Europe and CIS are slowly becoming significant consumers of ferroniobium. As a result, the world niobium market has been stable despite the slowdown in steel production in 2001. This paper will describe present producers, capacities and the current market conditions.

May 1, 2003

By P. Fellner, A. Sýkorová, J. Thonstad, J. Jurišová, V. Khandl

Adsorption of S02 on alumina used in the aluminium industry, so-called smelter grade alumina, was studied in the temperature range 15 C-120 C. The specific surface area of the smelter grade alumina was 88 m2/g. It was found that at temperatures lower than 40 C, sulphur dioxide is bonded to alumina reversibly by physical forces, and the adsorption can be described satisfactorily by the Langmuir adsorption isotherm. The heat of adsorption was estimated to be -33 kJ.mor1. At temperatures in the range 80 C- 120 C, which prevail in dry scrubbers in the aluminium industry, the heat of adsorption was determined to be -56 kJ.mor1. When S02 was adsorbed at temperatures higher than 80 C, about 30 % of the S02 could not be desorbed when heating the samples up to 250 C. In the presence of S02 and oxygen, the formation of sulphate was determined at temperatures above 90 C.

Jan 1, 2006

By Leslie F. Sawatsky

Raw water import requirements for oils sands mines depends mainly on factors such as ore processing rate, ore material characteristics, tailings processing technology, tailings storage systems, process water storage operations, the phase of tailings production, and non-recoverable seepage losses from tailings ponds. These factors can be readily quantified to calculate raw water import needs. Nevertheless, mine water balance continues to be misunderstood by some regulators, stakeholders and possibly even mine operators. Confusion over consumptive uses has led to a focus on recycling which is not necessarily applicable to a closed circuit water management system. Some water conservationists focus attention on raw water intake rules instead of the technical decisions that control consumptive uses. Typical oil sands mine water balances for various types of tailings operations, are analyzed to illustrate the effect of controllable and uncontrollable parameters as well as major options that need to be explored for reducing water demand. Uncontrollable parameters including tailings fines content, oil content of ore, connate water, mine depressurization water inflows and surface water hydrology. Controllable parameters include storage operations, advance water supply ahead of mining operations, type of tailings operation, net tailings pond seepage losses, and tailings impoundment operations. Potential reductions of raw water supply rates may be obtained by providing greater on-site storage to attenuate fluctuation in water demand, advance water accumulation prior to mine start up, early commencement of CT operations, thickened tailings disposal and paste technology. Water conservation measures should be focused on reducing on-site process water storage and water content of tailings material.

May 1, 2004

By The Mill Staff

Introduction The Hollinger cyanidation mill commenced operating in June, 1912, and 49,779,978 tons of solids had been discarded by the end of 1950. The present tailing disposal plant has been in operation since 1924 and holds 39,762,250 tons. The tailing disposal plant is on the property of Kayorum Gold Mines, Limited, about a mile and a quarter south of the mill. The area available for tailing covers 640 acres and is roughly l ¼ miles long by ¾ mile wide. Tailing was first deposited on the McKay veteran claims, l mile long by 1/2 mile wide, which were later included in the Kayorum property. This site sloped from northeast to southwest, the slope amounting to 106 feet between the northeast corner and the low land to the southwest. The low land was wet and a considerable area was covered with muskeg up to 17 feet deep. It was drained by a brook running across the property in a southwesterly direction. Later, when more ground was needed, the low-lying mining claims adjacent to the south and west boundaries were acquired to allow for the extension of the plant. This entailed some extra difficulties and expense that would not have been encountered had the whole of the present site been acquired with the original purchase. At the present time, the top of the tailing deposit stands at two elevations, but eventually the tailing deposited on the extension to the original plant will be raised to the same height as the older deposit. Previous to 1924, all of the tailing was deposited on Low land and in lakes near the mil1. Between 1924 and 1926 an increasing tonnage was sent to the McKay claims until, in 1926, all of it was being sent there. In 1936, the area of the deposit was extended and shortly afterwards all of the tailing was deposited on the new site.

Jan 1, 1951

By M. Kunst

The creep behavior of three AJ62 alloys was investigated in a wide range of stresses and temperatures. Multi-level tensile creep tests revealed a distinct primary creep stage and a high stress exponent up to a value of 10. The threshold stress concept which is commonly used in combination with high stress exponents was utilized in the analysis of creep behaviour. This resulted in an effective stress exponent for the AJ alloys indi¬cating dislocation climb as the dominating creep mechanism. In addition, microstructural observations of the lamellar eutectic and of the a-Mg-matrix were carried out using opti¬cal microscopy, SEM and TEM. The creep properties of the alloys are discussed in the context of microstructural parameters such as phase volume-fraction, stability and solute supersaturation.

Jan 1, 2006

By S. Hunt, S. Jayasekera, J. Kyle, N. Perera, K. Stone

A preliminary investigation has been conducted to determine the conditions for the precipitation of phosphate from the liquor produced after a hydrochloric acid pre-leach and rare-earth recovery from a rare earth containing fluorapatite concentrate from the Nolans rare earth deposit in the Northern Territory of Australia. The results show that at 50oC the phosphate can be precipitated in two stages using limestone to produce a Stage 1 precipitate containing most of the impurities including iron (94%), aluminium (92%), fluoride (98%), uranium (84%) and thorium (94%), followed by a relatively pure Stage 2 dicalcium phosphate precipitate (DCP) containing only 0.05% Fe, 0.05% Al, 0.1% F, 0.01% U, and <0.01% Th. The initial Stage 1 precipitate contained about 25% of the phosphate while the remaining 75% reported to the Stage 2 phosphate precipitate. Depending on the required radioactivity specifications, the amount of phosphate in the Stage 1 precipitate could be reduced. Reagent requirements were 11.4 kg limestone (as pure CaCO3) per cubic metre of solution for the Stage 1 precipitate and 39.7 kg limestone (as pure CaCO3) per cubic metre for Stage 2. The analysis of radionuclide balance indicated that radionuclides deported mainly to the final filtrate (86.4%) compared to Stage 1 precipitate (5.4%) and Stage 2 precipitate (8.2%). Settling and pressure filtration tests indicated the precipitates were both readily settled and filtered. The final moisture contents of the Stage 1 and Stage 2 precipitates were 62.5% and 49.3%, respectively.

Jan 1, 2014

By Filipe Beretta

This study investigates geophysical logging capacity to predict coal quality. It was analyzed for possible correlation, some parameters determined via laboratory analysis of coal against results for the same parameter derived from wireline logs recorded by a geophysical probe. These probes detect variations in some rock physical properties, such as their natural gamma ray emissions and electrical resistivity. Results showed a strong correlation between natural gamma and ash content, establishing a linear model to estimate ash content from geophysical logging data with a low estimation error (less than 5%). Besides, results showed that there is no correlation between sulphur content or volatile matter and resistivity, neither with natural gamma of the rocks. Ash content derived from gamma ray values can be used as secondary information to evaluate coal quality during resources estimation, using methods such as soft indicator kriging. The methodology is illustrated using a case study at a coal deposit in south of Brazil.

Oct 1, 2009

By E. Zucker

In this paper, as in the 1960 CIM paper of the same name, s1gmf1cant new developments in electrical-mechanical mining equipment are briefly described. These include static thyristor-supplied D.C. drives for mine hoists, load-haul-dump systems, process controls with small and medium-size computers, and several other new items of equipment and Concepts. All the new hardware descriptions are given in the context of over-all process integration. This means the actual mechanical linking together of two or more processes and the preliminary step in the development of production-line mining.

Jan 1, 1969

By T. Skinner, M. Sahebkar

"In recent years, the mining industry has been inundated with new technologies and software systems to aid in productivity improvement. Accompanying this increased level of technology and computer systems has been the exponential growth in data sources and sinks for all aspects of a mining operation. This rapid growth in data and technology has evolved through vendor “push” approaches and user “pull” scenarios, the result of which has been that currently, no standards exist defining how data from new technology should be accessed and transferred from surface mining equipment and systems. Consequently, many incremental benefits of the systems have not been realized. This paper will present a discussion of this important issue and introduce a new committee formed to address standards to assist the industry in making effective use of current and future technology. Potential benefits accruing from the development of these standards will be illustrated through the use of a case study at Fording Coal Limited. IntroductionThe mining industry is currently faced with a rapid evolution in the computing-based systems capabilities of mobile production equipment. At the same time, there is a trend toward the introduction of even larger machines, with novel designs or incorporation of new technologies within existing designs. Computing and control technology will be required to operate and acquire knowledge about equipment operation, utilization, and performance. Such knowledge has the potential to lead to enhanced equipment design, more appropriate equipment selection, and optimized equipment performance. The equipment systems will be required to be integrated with mine production monitoring systems, maintenance management software, and a wealth of other information systems to provide a complete understanding of the effects of various factors such as maintenance, equipment design and production on economics (Roman and Daneshmend, 2001). This will lead to a better understanding and implementation of the opportunities to enhance the performance of the mine through interaction of the mine operations."

Jan 1, 2003

By Arthur Notman

Since addressing the Institute a year ago on The Future of the Copper Industry (l), many things have happened, most of them bad. It has been a hard year for profits and prophets. It was, therefore, with consider-able perturbation that I accepted the gracious invitation of your Committee to reappear. On reviewing my remarks of a year ago, I. have wondered whether, under pressure of more important matters, the Committee had neglected to make a note of them, or whether they felt that further explanations from me were in order. In either event, I am glad that I am here and welcome the opportunity to make any contribution I can to a clearer understanding of the problems of copper to those concerned. The English-speaking nations own 80 per cent of the present world-production of the metal. Col. P. E. Barbour, Secretary of the Mining and Metallurgical Society of America, and I recently completed an estimate of the known world resources of copper. We placed the figure, in round numbers, at 100,000,000 tons of metal. Of this amount, about one-third lies in the United States, one-third in the British Empire, and one-third in South America; and all but 4 per cent of this is owned by British Empire and United States capital. Our figures do not include any estimates for Russia, Japan, or Europe, on which there are no available data. It is true, consequently, that the British Empire and the United States are the ones concerned. It seems to me to be a matter of great importance to the world at large, and of even greater importance to those nations themselves, that the known sources of supply of this metal, so essential both in peace and war, rest so strongly in their hands. I cannot believe that in the long run they will neglect their responsibilities in the wise administration of these resources.

Jan 1, 1932

By Fred G. Hewett

Cassiar Mine in northern British Columbia began development in 1952. The deposir is found on rhe west limb of rhe McDame Synclinorium in a Mississippian serpentinite body. The serpenltntte, one of the McDame l ntrusives, imrudes Sylvester Group . rocks, which comprise a Lare Devonian to Early M1ss1ss1pptan eugeosync/inal sequence of argillites, quarrzires and volcanics. The foorwall conracr berween Sylvester Group rocks and rhe serpenrinire is a marked zone of broken and incomperent argillite and graphitic schist. The less marked hang- 111gwall contacr 1s a band of indurated argillite. The JurassicCretaceous emplacemenr of the Cassiar Graniric Barholilh is responsible for mosr of the numerous )aims, faulrs and shear zones found in the serpentinite body. Faulting occurred borh before and after asbestos formation. Asbestos is mined from an open pit ar rhe rate of 4,535 ronnes daily. It passes from the pir along a rramline to the mill, where it is concen/rared into nine direcr milling grades. Packaged fibres travel ro over 40 counrries around rhe world for use in the texrile, cemenr and other industries.

Jan 1, 1984

By H. K. Olsen, B. Thomassen, H. K. Schønwandt, L. Grahl-Madsen, H. Stendal

Abstract-The central part of the early Proterozoic Ketilidian orogen in South Greenland consists of an I-type granitoid batholith transected by four regional NE-SW-trending shear zones. The batholith was probably emplaced during subduction, from the south toward the Archaean craton in the north, in a sinistral transpressional system. A regional sediment sampling program covering 5000 km2 shows a close connection between a gold-mineralized trend and one of the major shear zones within the epizonal facies of the batholith. The gold mineralization is not directly related to the major shear zones, but occurs in quartz-veined and silicified second-order structures. High-grade (up to 114 ppm Au over 6 m) low-tonnage mineralization is found within these second-order structures cutting both amphibolites and granitoids. The mineralization is characterized by negligible or small alteration halos. Gold is associated with various element combinations of enhanced As-Bi-W- Cu, which indicate that the mineralization is mesothermal in origin.

Jan 1, 1995