Search Documents

By N. C. Clarke, T. Wu, M. le Page, K. J. Henley

In 1994, Gold Mines of Australia acquired the rights to the historic Mt. Lyell copper mine, and commenced a feasibility study into expanding production. The ore was shown in laboratory tests to be amenable to single-stage, fully autogenous grinding (FAG) of underground primary crushed ore, and this route offered the maximum cost savings. Flotation performance was expected to be enhanced. However, batch flotation tests done on pilot-scale autogenously ground ore showed an unexplainable recovery loss of between 1% and 3% Cu. A second pilot plant trial was set up, with the ground product feeding banks of continuous flotation cells. Single-stage FAG, FAG/pebble and FAG/ball circuits were tested. Results confirmed a loss of about 3% recovery with single-stage FAG milling. The FAG/ball circuit eliminated the loss. Analyses showed that autogenous milling probably produced more chalcopyrite/pyrite composites and that recovery of these composites was lower than with ball milling. In size fractions below about 53 microns, where chalcopyrite is well liberated, copper recovery was less affected by milling method and flotation selectivity. It was concluded that for the Mt. Lyell situation, a FAG/ball circuit was preferable to single-stage FAG.

Jan 1, 2002

By Edouard Asselin, Tasawar Javed

The precipitation of hematite from ferric sulphate - cupric sulphate - lithium chloride acidic solutions was studied in a batch reactor. The effect of several variables on the extent of hematite precipitation as well as on its crystallinity and purity was investigated. The variables studied include: initial ferric concentration (1.5 - 30 g/L), retention time (0 - 12 h), initial sulphuric acid concentration (0 - 30 g/L), temperature (150 - 220 °C) and chloride concentration (0 - 25 g/L). The results show that hematite is preferentially precipitated at lower initial iron concentrations. Longer retention times increased the fraction of hematite in the precipitates but did not affect its crystallinity to a significant extent. On the other hand, higher temperatures increased the purity and crystallinity of the hematite. At lower acid concentrations hematite and goethite were precipitated. However, only hematite was precipitated when the initial acid concentration was > 12.5 g/L. Better crystalline hematite was formed at lower acidities. Increasing chloride concentration increased the amount of hematite and decreased the amount of iron sulphate hydroxide phases, but did not affect the crystallinity of the hematite.

Jan 1, 2015

By J. M. D. Wilson, W. Petruk, C. Coté

"The behaviour of minerals in the Mount Wright spiral circuit was investigated to find methods of improving iron oxide mineral liberation and recovery. The feeds, concentrates and tailings from rougher, cleaner and recleaner spirals in one mill line were sampled before and after the sizing screen openings were reduced from 2 mm to 1.6 mm. Sized fractions of each sample were analyzed with the MP-SEM-IPS image analysis system at CANMET to determine mineral quantities and liberation characteristics of the iron oxide minerals. Mass balance techniques were used to calculate stream recoveries of iron, silica, total iron oxide minerals, hema¬tite, goethite, quartz, ferromagnesian silicates, and liberated and locked total iron oxide minerals for each sieve fraction.The reduction of the sizing screen openings increased the ap¬parent liberation of the total iron oxide minerals in the screen undersize from 89% to 94% and raised the over-all iron recovery from 84.4% to 85.3%. Apparent liberation of iron oxide minerals in the cleaner sand also increased from 70% to 85%, but the – 75 µm fraction re¬mained the only fraction containing an acceptable amount of liber¬ated iron oxide minerals in each case. Due to limitations of spiral and grinding efficiency it is recommended that the cleaner sand be screened at 300 m, the +300 m fraction be reground, and the – 300 p.m fraction be rerouted to the rougher spirals.The amount of fine liberated iron oxide minerals (– 106 m) lost in the tailings was 46 TPH in mill line 3. This value represents 41 wt % of the free fine iron oxide minerals, or 7 wt % of the total iron oxide minerals in the spiral feed. Further work is needed to investigate the possibility of recovering this material by other methods.Middling iron particles (010 50%) and presumably free gangue in the size range –300+ 75 m tend to be recovered by spirals by entrapment."

Jan 1, 1990

By Nick D. Rose

The importance of structural geology in open pit slope stability is overlooked in many mining operations due to pressures to cut costs and minimize mine personnel. As a result, mine geology staff are often unable to keep up with geological mapping of the pit slopes due to other day to day production oriented tasks. In some instances, key structural controls that contribute to slope instability may not be identified until after a slope instability has initiated, at which time it may be difficult or impossible to delineate these features in the field. Even for small slopes, understanding the engineering and structural geology of the rock mass, as well as the effects of groundwater and blasting practices, are of key importance to slope stability. Two case histories are presented as examples of mining operations that experienced slope instability with little more than anecdotal information about the structural and groundwater conditions encountered during mining. By conducting field reconnaissance, simple slope stability analyses and ongoing slope monitoring, practical remedial measures were implemented, allowing continued safe mining operation.

May 1, 2002

By Raymond Dallaire

The Humphrey's spiral is a static gravity separation device which cannot be adjusted to match short-term variations that occur in the feed. Any disturbance in the feed grade, per cent solids or flow rate affects substantially the recovery and grade of concentrate. Such variations must be minimized in order to maintain the desired rate of production and quality of the product for which the installation has been designed. A study has been performed in which the foregoing assertions were quantified. The feed grade, per cent solids, flow rate and particle size were varied independently. Ore from Carol Lake, Nfld., was used throughout the experiments. This consisted of specular hematite and magnetite in a silica gangue.

Jan 1, 1978

By S. D. Botts, F. Cantuarias

"The Antamina project, owned by BHP Billiton Plc, Mitsubishi Corporation, Noranda Inc., and Teck Cominco Ltd., is a $2.3 billion copper/ zinc project, located in the Ancash Department of Peru. The project consists of an open pit mine, a 70 000 ton per day concentrator, a 302 km long concentrate pipeline, port facilities, a new access road, power line, and town site. The project is designed to produce up to 1.5 Mtpy of copper and zinc concentrates over a 23 year project life, and will be the third largest producer of zinc and the seventh largest producer of copper in the world.This mega project is the largest mining investment in the country and, during its construction stage, was the most important construction project worldwide. On May 28, 2001, Antamina commenced testing operations and four months later, it reached commercial production. Antamina was officially inaugurated on November 14, 2001 by Peruvian president Alejandro Toledo.The construction stage of the project generated 8000 direct jobs, with a peak of 10 000 employees, and 30 000 indirect jobs. The permanent workforce consists of approximately 1650 employees, the vast majority of which are Peruvian Nationals, around 30% of whom came from the region where the deposit is located. Approximately 5600 indirect jobs were generated from the project. Independent sources state that Antamina increased the Peruvian mining exports by 30% (mining exports constitute 50% of Peru’s total exports) and Peruvian GDP by 1% in its first year of full operation in 2002.Since winning the privatization bid for the project in 1996, the company has implemented an approach to community development and environmental protection based on sustainable development principals. Throughout the development of the project, a number of initiatives have been undertaken to ensure full involvement of the local populations in community development activities and the company’s environmental program.Due to its size, difficult logistics, cultural considerations and financial aspects, the project has faced a number of unique challenges in the area of environmental protection and management of community interaction. Antamina has been innovative in its approach to these issues and, as a result, has set new standards in Peru for environmental and community management and sustainable development."

Jan 1, 2003

By A. Alfantazi, E. Asselin

"The corrosion of commercially pure titanium (CP-Ti) was studied from room temperature up to medium temperature (~160°C) under conditions relevant to medium temperature chalcopyrite leaching processes. The corrosion rates were measured by immersion and electrochemical tests in sulfuric acid. The influences of chloride, cupric and ferric ions on the corrosion rate and behavior were also investigated. Corrosion of the CP-Ti did not account for the total current density measured by linear polarization tests. The corrosion rates of CP-Ti under medium temperature leaching conditions were surprisingly high. The corrosion rate measured in ferric containing solution at 160°C was approximately 20 mm/yr.INTRODUCTIONTitanium exhibits excellent corrosion resistance in many aggressive environments because of the formation of a very chemically stable, highly adherent, and protective oxide film on its surface (Mitsuo et al., 2002). Because titanium is the only metal available at a reasonable cost that resists the high temperature corrosive slurries in many leaching processes, it is often chosen as autoclave liner material where it is subjected to severe conditions of acidity, temperature and pressure (Grauman and Say, 2000).A number of distinctly different hydrometallurgical processes for the pressure leaching of chalcopyrite have been developed and patented by various companies and they can be classified into low, medium and high temperature regimes (McDonald and Muir, 2007). For example, chalcopyrite concentrate may be processed at medium temperatures (115-175°C) and pressures of 800-2200 kPa (Dreisinger, D., 2006; Sahu and Asselin, 2011). The lixiviant may contain 20 to 55 g/L sulfuric acid, 8 to 12 g/L chloride ions, 10-25 g/L Cu2+ (Jones, 1995, 1997, 1999), and less than 1 g/L Fe3+ (Defreyne et al., 2005). The amount of these additions is determined by the grade of the ores and details are shown in Table 1."

Jan 1, 2012

By T. G. Carter

"Damaging seismicity associated with deep faulting in both mining and civil excavations not infrequently occurs without warning, and often before proper mitigation measures have been put into place. Severe squeezing is also a common problem for excavating through deep major faults. While both problematic conditions are difficult to predict and characterize, there is often a need at pre-feasibility and feasibility level to more reliably estimate the possible level of risk posed by such geologic structures. This paper introduces some structural geologic techniques that have potential application for both mining and civil applications for aiding forewarning of the extent of these types of problem.INTRODUCTIONEncountering adverse faulting at depth in deep excavations, whether for mining or civil purposes can create serious economic and safety impacts. For deep mines or for deep tunnel projects, measures are available for aiding prediction of the extent of possible influence that large scale faults could create, but these techniques are rarely if ever applied as part of routine site investigation programs, or even as part of risk assessment evaluations. Several well established structural geologic methods of palao-history reconstruction have potential application for aiding forewarning of the extent of these types of potential problem by allowing estimates to be made of:• controlling stress orientations that might engender reactivation movement;• principal stress magnitudes that could lead to failure initiation, and• probable mechanisms of fault deformation - brittle (bursting) or plastic (squeezing).This paper explores several structural geological and rockmass characterization techniques that have application for unravelling fault structure of importance to deep engineering projects. Their application for mining or tunnelling purposes is advocated in conjunction with conventional rockmass characterization assessment approaches using GSI, RMR and/or Q to aid early recognition and definition of potential adverse ground condition behaviour associated with intersection of significant faulting at depth."

Jan 1, 2015

By D. R. Nagaraj, Napoleon Tercero, Raymond Farinato

"Several studies conducted recently have shown that molybdenite flotation from Cu-Mo ores is adversely impacted in sea water at pH >~ 10.0 irrespective of the pH modifier; under the same conditions Cu sulfide flotation is relatively unaffected. This has been attributed to the presence of Mg2+ ions and their hydrolysis products in the sea water which adsorb and precipitate on molybdenite surfaces as Mg(OH)2. However, why and how Mg(OH)2 impacts only molybdenite flotation in the complex flotation pulps containing a multitude of minerals is not understood. The work presented in this paper probes the interface and interphase regions near the edge and basal planes of natural molybdenite (MoS2) in aqueous solutions and flotation pulps, particularly in the presence of copper ore pulp and added Mg2+. Differences in interaction of metal ions and their hydrolysis products (Mg2+, Mg(OH)+) were measured on the two faces of this anisotropic mineral. How those differences relate to molybdenite floatability and the impact of aqueous solution chemistry are discussed.INTRODUCTIONWater resource management is an important sustainability challenge in mineral processing. In view of the shortage of fresh water in many parts of the world, mineral processing plants are evaluating alternative sources. Seawater flotation has received much attention recently and there have been several important studies reported in the literature, particularly for the processing of Cu-Mo ores (S. Castro, 2012; S. Castro, Rioseco & Laskowski, 2012; S. Castro et al., 2012; Laskowski & Castro, 2012; Ramos, Castro & Laskowski, 2013; S. Castro & Laskowski, 2013; Laskowski, Castro & Ramos, 2013; Nagaraj & Farinato, 2014; S. Castro, Uribe, & Laskowski, 2014; Veki, 2013). The main conclusions from these studies on Cu-Mo ores in seawater at elevated pH were: a) flotation recovery of Cu sulfides is either unaffected or only marginally reduced, b) molybdenite recovery is adversely affected in seawater at pH values necessary for rejecting pyrite (i.e. pH > 10 to 10.8 depending upon particular system), and c) the precipitation of Mg2+ in seawater as Mg(OH)2 is responsible for the adverse effect on Mo flotation. In order to further investigate the individual effects of Mg2+ and Ca2+ on molybdenite depression in Cu-Mo ore flotation, Nagaraj & Farinato (2014) conducted flotation tests wherein individual metal ions were spiked into tap water during grinding of Cu-Mo ores. They showed the strong adverse effect of Mg2+ addition on Mo recovery and, to a lesser extent, on Cu recovery when pH > 9.5. Under similar conditions, Ca2+ had virtually no effect on either Cu or Mo sulfide flotation. Figure 1 below shows the previous results for Cu- Mo ores in tap water and the effect of addition of Ca2+ and Mg2+ ions. Note that in seawater the adverse effect of Mg2+ on Cu recovery was much smaller than that in tap water (Nagaraj & Farinato, 2014; Figure 4a and 4b and Table 4 therein)."

Jan 1, 2016

By G. Auld

"A simple method is presented whereby the additional quantity and static pressure necessary to compensate for ventilation duct leakage may be estimated using the circular reference functions of modern spreadsheets. Favourable comparisons have been made to the National Coal Board (United Kingdom) design charts and to a case study analysis. IntroductionIn mining, most ducted systems are applied to the development of access tunnels, and most of these systems leak to some extent. When the ventilation duct fails to deliver the required quantity of air to the work place, there is a significant contribution to the development costs, either directly or indirectly.Directly — More air and more pressure are required to compensate for the leakage, more capital development (ventilation shafts, parallel drives) are required because ventilation systems cannot push the fresh air far enough, and longer re-entry times to ensure toxic blast fumes to be diluted.Indirectly — There is a reduction in productivity because of the inclement atmospheric conditions, and/or closure of development ends because of unacceptable atmospheric conditions at the working place. This has been exacerbated over the last few decades because of the increased use of diesel equipment of ever increasing power, and the more stringent Occupational Health and Safety requirements demanding more air flow per kilowatt of diesel power.The leakage from a duct must, therefore, be reliably estimated in order to assess the effectiveness and construction of the system; assess the effectiveness of the maintenance or repair of the duct; appreciate the cost of the leakage, and therefore apply effective maintenance and installation procedures; and engineer safer, healthier and more cost-effective ventilation systems."

Jan 1, 2002

By Jerry J. Ran

In open stope mining borehole deviation is one of the main factors affecting the blasting results. Though previous research has identified some actual deviation patterns, these studies are unable to relate the hole deviation pattern with the blasting results and therefore it is not possible to modify the design or take remedial measures based on the prediction of the blasting results. An alternative to the conventional method for borehole surveying is the in-hole probing techniques. With their inherent errors, it is important to evaluate these surveying systems under conditions of different mine sites. The lack of available assessment methods has limited the application of these techniques. In this paper some of the characteristics of the actual hole deviation pattern are discussed based on data from surveying production holes in six stopes. A method of predicting the blasting results is proposed by considering the borehole deviation pattern. Based on the prediction stope design can be modified or further surveying is carried out to improve the blasting results. The tolerable error is introduced to relate the surveying error with the drilling pattern and therefore it is possible to assess various in-hole-surveying techniques.

May 1, 2002

By Deon van Tonder, Chuck Edwards

"Solvent extraction is used in many acid leach uranium circuits to upgrade and purify the uranium bearing solution prior to final product precipitation. A number of strip options are available to recover the uranium from the loaded organic. This paper compares some of these options on the basis of typical capital and operating costs for both the solvent extraction circuit and downstream uranium processing, and also considers other related issues. The aim is to provide an objective comparative assessment of these options that could be used as a qualitative guide in process selection or improvement.INTRODUCTIONIn the 1950s the uranium industry was the first industry to adopt solvent extraction (SX). Since then, the flow sheets have advanced. Notable was the introduction of tertiary amine extractants by General Mills during the late 1950s and 1960s (Mackenzie, 1997; Mackenzie, 2005), which is still today considered ‘state of the art’ technology. Initially solvent extraction was done in combination with ion-exchange, such as in the Eluex flow sheet, followed later by the adoption of direct solvent extraction from pregnant leach solution (PLS). From a strip-precipitation perspective ammonia strip followed by ammonium diuranate precipitation was widely adopted as the norm in the uranium industry. More recently alternative strip systems have been receiving increasing attention due to the environmental, health and safety issues associated with ammonia and the resulting calcined uranium oxide product. This paper explores some of these alternative options in comparison with the ammonia route.It is important to acknowledge that each operation is unique, and therefore the information and philosophy outlined in this paper serve to provide a general guide that can be potentially applied and adapted to any site or project."

Jan 1, 2013

By D. A. Barr

"Most of the lode and placer gold production in the Canadian Cordillera has been derived from mines and placers in the Intermontane and Omineca belts. Gold has been produced from rocks of Precambrian to Eocene age, but the preferred host environment contains Upper Paleozoic to Upper Jurassic eugeosynclinal or arc-type sedimentary and volcanic rocks adjacent to plutonic complexes which have a wide variety in both size and composition. Auriferous quartz lodes occur in fissures and shear zones which are commonly subsidiary to strong fault zones. In common with most vein-type deposits, structural complexities are an essential part of the mine environment.Gold production from the Canadian Cordillera to the end of 1978 totals 35.0 million ounces, of which 47 per cent has been produced from placer mining, principally in the Klondike and Cariboo districts. The balance has been derived from lode gold (80 per cent) and base metal (20 per cent) mines.Gold reserves in producing mines and deposits committed for production as of January 1, 1978 were 87.4 tons, or 21.6 per cent of total Canadian gold reserves contained in all types of deposits. Although more than 100 lode mines have operated in the Canadian Cordillera since the turn of the last century, over 75 per cent of the lode gold produced by 1978 was recovered from five mining camps, namely the Rossland, Hedley, Bridge River, Premier and Barkerville.The average grade of the principal producers in these camps was about 0.45 ounce of gold per ton. Individual camps yielded from 3 to 8 million tons during their operating lives, which varied from 28 to 43 years. The last of these mines ceased operating in 1971.Most of the total lode gold production has been derived from quartz veins, frequently with associated carbonate and ankerite, occupying fractured and faulted zones in Mesozoic volcanic and sedimentary rocks closely associated with a variety of intrusions. A review of the literature suggests that several deposits may have evolved by remobilization of ore constituents from earlier concordant gold-bearing formations. The principal metallic minerals in the deposits are native gold, electrum, tellurides, pyrite, arsenopyrite, pyrrhotite, sphalerite, galena and chalcopyrite.As the mineralogy suggests, many of the Cordilleran lode gold deposits have yielded important co-products or byproducts, including silver, copper, lead, zinc, cadmium and tungsten. Significant by-product gold production has also been derived from porphyry copper, volcanogenic, replacement and pyrometasomatic deposits, particularly in recent years.No major lode gold discovery has been made in the past 67 years, although little exploration activity for gold has taken place during the last 30 years. Several relatively small lode gold and gold replacement deposits have been discovered in recent years, either serendipitously (Chappelle) or on very low initial budgets (Northair and Carolin). Based on well-established precedents, one or more of these may eventually be developed into a large mine.A detailed study of the Canadian Cordillera gold deposits based on recent genetic models could prove rewarding, not only in up-dating information on their origin and depositional characteristics, but in stimulating the search for undiscovered gold deposits, in the Cordillera and other parts of Canada."

Jan 1, 1980

By R. E. Gilmore

PREAMBLE THIS PAPER comprises material presented in two separate 'Papers at the British Commonwealth Scientific Specialist Conference on Fuel Research held in London, England, in July, 1950. These papers are now available for publication in Canada, since only essential parts of the conference discussions, in addition to the resolutions resulting therefrom, will be published in the official Proceedings of the Conference. Inasmuch as the information presented concerns Canadian organizations and training facilities for fuel research, it should be of general interest to Canadian scientists, and especially to the Coal Division of the Canadian Institute of Mining and Metallurgy. Part I, the alternate title of which is Facilities in Canada for Fuel Research and for Exchange of Information and Staff, does not include research on peat, oil shale, petroleum oils in general, and natural gas, and omits studies of the geology, constitution, and production of coal. Special reference is, however, made to research on the heavy crude oils and bitumen of the Western Prairie Provinces, and particularly to their production and treatment to produce crudes for oil refinery processing.

Jan 1, 1951

By Z. D. Hora

Brick shales and refractory clays are mined at Sumas Mountain near Abbotsford. Sholes and stoneware clays elsewhere in the province have not been developed. THE SUMAS MOUNTAIN deposit near Abbotsford, 80 km east of Vancouver, has been in continuous production since 1905. The deposit is exposed in a small outlier and comprises a sequence of alternating beds of clay and sand. Beds are of Eocene age. Within the 400 m thick ness of sediments are seven distinctive conglomerate members, some up to 20 m thick, interbedded with fine grained sediments including claystones and siltstone , or "shales". Shale is quarried to produce a variety of bricks, sewer pipes and similar products; it is also used for cement. Several different shale beds have been mined over the years and exhibit a variety of fired colours ranging from buff-pink grey to deep red; pyrometric cone equivalents (PCE) range from 3 to 20. A layer of fireclay 3 to 4 m thick that occurs at the base of the sequence has pinkish white to light buff fired colour and PCE of 30 to 33. It is used as a 266 primary component to produce refractory bricks. The shale is quarried and processed by Clayburn Industries Limited of Abbotsford. Another similar but smaller outlier of the same geological formation is known from Blue Mountain, about 20 km northwest of Mission. Other ceramic clays in British Columbia are reported from Quesnel (7 m bed of white stoneware clay, PCE 17 to 19), Giscome Rapids (25 km north of Prince George, 10 m bed of stoneware clay to PCE 31) and anaimo-Comox area (buff to red firing "shales", PCE 8 to 10-1 12) . From 1959 to 1974 Cretaceous shale from Saturna Island in the Strait of Georgia was used to produce lightweight aggregate. Similar deposits of expanding shale are known from the vicinity of Duncan on Vancouver Island.

Jan 1, 1984

By D. D. Tannant

An experimental and numerical study was conducted on the geomechanical behaviour of oil sands during penetration tests in which a steel wedge with an apex angle of either 20 degrees or 30 degrees was forced into compacted oil sands. The boundary conditions simulated in the laboratory tests are similar to shovel penetration into oil sands. The objective of the laboratory tests was to measure the force required to push a steel wedge into compacted oil sands. A wedge penetration test differs from conventional triaxial tests in that much more shear is generated. The laboratory data was needed to improve calibration of micro-mechanical input parameters for a two-dimensional discrete element model of oil sands constructed with Particle Flow Code (PFC). Initial model calibration was performed with triaxial test data and then a PFC model of the wedge penetration test was constructed. The measured force-displacement behaviour of the steel wedge was compared with PFC modelling results. It was found that different combinations of PFC particle and bond parameters could equally well replicate the laboratory triaxial compression data for bitumen-rich oil sands. When the wedge model was run, it was found that the resulting force required to penetrate the wedge into the oil sands was about four to six times higher than that measured. This clearly indicates that further research is required to improve the predictive capability of PFC models of oil sands.

Jan 1, 2002

By L. M. Gould

"Syncrude Canada operates the largest oil sands crude oil production facility in the world and produces over 13% of Canada’s total oil requirements. To achieve this, Syncrude mines the oil sands in open pits, extracts the raw oil known as bitumen from the sand using water-based processes and upgrades it into sweet light crude oil by fluid coking, hydroprocessing, hydrotreating and reblending. The final product, Syncrude Sweet Blend (SSB), is sent by pipeline to three Edmonton area refineries and then to pipeline terminals which ship the SSB to refineries in Canada and the United States.As parts of the Mildred Lake base mine reached their economic life, they were replaced with new facilities at the Aurora Satellite mine. Aurora is situated on Oilsand Leases 10, 12 and 34, 35 km northeast of the Mildred Lake facility (Fig. 1).In 2000, the first hydrotransport low-energy extraction production train started up at Aurora. A second production train is scheduled for start-up in 2003. Open pit mining at Aurora occurs using two hydraulic shovels, two cable shovels, and trucks ranging from 320-ton to 380-ton payload capacities (Fig. 2).Once the oil sands is excavated, the trucks dump the ore into a crusher designed to break up the big lumps of oil sands and rock at peak rates of 11 000 t/hr. The ore is then transferred by conveyor to a surge pile and then to a mixing box which combines the oil sands with hot water. Following bitumen separation in the primary separation vessel, froth is delivered to Mildred Lake for processing via the intersite pipeline (Fig. 3).The goal of this paper is to illustrate how high precision shovel GPS (HPGPS) is being used at the Aurora mine to aid in mine planning. This can be accomplished by first describing the function of the mine planning department, describing the Aurora orebody, and finally explaining how the HPGPS system functions and how it is employed at Aurora.The short range mine planning department ensures a steady supply of ore is delivered to the plant at the desired grade in a sequenced and economical manner. This is done by creating a mine plan that consists of shovel dig locations that require the shovels to mine in a specified area at a specified elevation."

Jan 1, 2002

By D. T. Aikens, R. Gaudreault

"This paper summarizes structural repairs carried out on a marine wharf consisting of six 13.7 m by 13.7 m reinforced concrete cribs linked together by five 14.6 m long beam spans. As a result of problems during original construction and twenty years exposure to severe weather conditions, the deck support system between the cribs required major restoration work. In particular, some of the beam seats under the crane rail supports had marginal bearing area to support the structural loads. Faced with closure order for the wharf which is required to bring in raw materials to the plant and a long outage to make repairs as stipulated by Ports Canada (owners of the structure) alternate means of making the required repair were examined.The method chosen allowed the work to be done much more quickly, at lower cost, without taking the wharf completely out of service. The badly deteriorated seats were rebuilt using epoxy grout, tapered sole plates and a positioning jig."

Jan 1, 1988

By C. S. Maggs, L. Shwydiuk, H. W. Newcomen

The southwest wall of the Lornex Pit at the Highland Valley Copper mine has been experiencing slope displacements since 1978. Measures to manage the displacements on previous pushbacks have included stepping out, scheduling pushbacks to unload the crest of unstable areas, slope dewatering and mining with intensive slope monitoring. The final pushback on this wall is currently being mined and substantial modifications to the slope geometry could prove to be uneconomical. As a result, a campaign of surface water collection and diversion, horizontal drainhole drilling and deep well drilling is currently underway to maintain an acceptable degree of stability to the end of mine life. The various factors contributing to instability, including engineering geologic controls, rock mass strength, and surface and groundwater hydrology are presented. Movement trends, displacement magnitudes and stability analyses results are also discussed.

Jan 1, 2003

By M. B. Kime, E. K. Kanowa

"Heap leaching of low-grade copper-cobalt oxidized ore and solvent extraction of copper, cobalt, manganese, and zinc were investigated. Heap-leaching parameters were optimized using agitated and tray batch leaching tests, capped by tests on a pilot semicontinuous heap-leach plant. The optimum pregnant leach solution yielded 2,350 mg/L Cu, 3,800 mg/L Co, 3,600 mg/L Fe, 130 mg/L Mn, 25 mg/L Zn, and 0.58 g/L solids in suspension, with pH and acidity of 1.27 and 3.66 g/L, respectively. Copper, cobalt, and impurities (Mn and Zn) were extracted using (v/v) 30% CP-150, 20% IONQUEST® 290, and 20% D2EHPA, respectively; overall recoveries of copper, cobalt, and impurities were 98, 99, and 70%, respectively.RÉSUMÉ La lixiviation en tas des minerais oxydés de cuivre et de cobalt et l’extraction par solvant du cuivre, du cobalt, du manganèse et du zinc ont été étudiés. Les paramètres de lixiviation en tas ont été optimisés à l’aide d’essais de lixiviation en discontinu sur un plateau, complétés par des essais relatifs à une usine pilote de lixiviation en tas en semi-continu. La liqueur-mère optimale a produit 2 350 mg/L de Cu, 3 800 mg/L de Co, 3 600 mg/L de Fe, 130 mg/L de Mn, 25 mg/L de Zn et 0,58 g/L de solides en suspension, avec un pH et une acidité respectifs de 1,27 et 3,66 g/L. Le cuivre, le cobalt et les impuretés (Mn et Zn) ont été extraits avec un pourcentage volumique (v/v) de 30 % de CP-150, de 20 % d’IONQUEST ® 290 et de 20 % de D2EHPA, respectivement. Les récupérations totales de cuivre, de cobalt et d’impuretés étaient de 98 %, 99 % et 70 % respectivement.INTRODUCTIONBoss Mining S.P.R.L. is a privately owned hydrometallurgical plant located in southeastern Democratic Republic of Congo. It treats oxidized ores of copper and cobalt that are recovered by sulphuric acid heap leaching (Trujillo, Cisternas, Gálvez, & Mellado, 2014; Kime, Kanowa, Mulaba- Bafubiandi, & Diyambi, 2016) and solvent extraction processes (Crane, Urbani, Dudley, Horner, & Virnig, 2009; Fisher, 2011; Kime et al., 2016). The ore to the plant is primarily sourced from the Luita and Mukondo mines. Geological prospecting work by Gecamines and Boss Mining showed that the Mukondo mine contains a very large cobalt reserve not yet exploited, but with grades as low as 0.2%.Currently, Boss Mining is focusing on the production of copper, but is investigating methods to efficiently produce both copper and cobalt. A challenge in the production of cobalt from this ore is its presence in the third oxidation state. This requires the addition of reducing agents, which increases the overall operating cost (Kime & Makgoale, 2016). Cobalt solvent extraction is also very sensitive to impurities such as nickel, zinc, manganese, and aluminum, which are often co-extracted (Swartz, Donegan, & Amos, 2009). This sensitivity to impurities requires the optimization of operational parameters to lower impurity levels as much as possible in the electrolyte."

Jan 1, 2017