Search Documents

By T. Yalcin

"This paper describes the development of a mathematical model for determining the liberation of an ore at various grinding sizes, based on the combined results of microscopic counting, grinding tests, and chemical analysis.The method is illustrated with an application to the magnetite ore of Sherman Mine in Temagomi, Ontario. For this ore, a degree of liberation of 98.7% was determined at a grinding size of 90% passing 44 microns, which closely corresponds to the final grinding size employed at the Sherman Mine Concentrator.Introduction Liberation characteristic of ores have direct and significant bearing on overall economics of concentration processes.Target grades and recoveries can be achieved only it minerals are adequately liberated prior to separation. Degree of liberation depends on the extent of size reduction. However, due to the high costs associated with size reduction processes, it is important to keep size reductions within limits of satisfactory liberation. Prevention of excessive size reduction is also necessary because of inefficient mineral separations in very fine sizes. Hence, a study of reduction size — liberation relationship is essential for optimum profit from milling operations.A number of procedures have been developed for liberation studies (1-12), but there is lack of method for universal adoption.A new approach is presented in this paper that might provide a realistic estimate of liberation and give a practical guidance as to the degree of size reduction required for satisfactory liberation."

Jan 1, 1985

By R. W. Lawrence, J. B. Austin, P. B. Marchant, J. T. Chapman

"Biohydrometallurgy is the use of microbiological reactions to assist in the extraction of metals. Bioleaching offers an innovative alternative for the treatment of refractory gold-bearing sulphides (1). One particular cost advantage of bioleaching is the potential to enhance gold extraction after only partial sulphide oxidation. The apparent selective sulphide oxidation is more prevalent where the refractory gold is associated with arsenic and antimony (2). Oxidation of the pyrite minerals and arsenopyrite at different oxidation rates can result in high gold extractions at relatively low levels of sulphide oxidation due to preferential, or selective, oxidation of the arsenic mineral. Arsenic extraction rates in a bioleach process typically exceed the iron extraction rate. Therefore, in concentrates in which the precious metals are principally associated with arsenic minerals, liberation of the precious metals may be possible with high recoveries and less than complete sulphide oxidation. The capital and operating cost advantages of partial sulphide oxidation are inherently obvious and are briefly illustrated herein.Ultra fine milling (UFM) is another alternative for enhancing gold extraction from refractory sulphides. Some refractory gold is simply particle size sensitive and UFM can improve gold extraction without the need for costly sulphide oxidation (3). Fine grinding technology for enhanced gold recovery developed by Metprotech, South Africa, is currently producing 2 - 4 micron ground product using a single pass, stirred ball mill. Proper application engineering has ensured that plug flow occurs through the mill. Plug flow from the feed inlet at the bottom of the reactor ensures that short circuiting of feed does not occur and as a result, the mill product does not require classification.A combination of UFM as a pretreatment for bioleaching could provide a mechanism for enhanced selective sulphide biooxidation and/or increased overall gold extraction following biooxidation due to improved particle liberation ( 4). The effect of UFM on biooxidation costs will be discussed. Only sulphide concentrates are considered herein for application of UFM in combination with biooxidation."

Jan 1, 1990

By Phil Thwaites

"The mining industry uses many types of mineral and metallurgical plants to produce saleable product from ore mined. Plant design history has left current operations with a mixture of manual operation and various forms of automated process controls. Consequently, we typically see high variability in the continuous operations together with a shortfall in the attainment of full capacity, or higher utilization of consumables.At a level of best practice, “Operational Performance Excellence” focuses on process control, using automation and control systems to deliver process optimization. This more sophisticated delivery is a great deal more difficult than the first stage of equipment selection / installation. It includes the appropriate selection of the right instrumentation, control system, key process knowledge, individuals with a solid control engineering background/experience, and the essential backing/ support of the operations management team together leading to higher value delivery. Robust solutions can be realized, considerably minimizing process variation, thus leading to process optimization. This approach results in an easier, efficient and safer process while providing considerable returns for the plant owners.How variable are your processes, and do you maintain optimized process performance with dedicated resources, modern instrumentation, ‘best practice’ control systems and performance monitoring tools? In this lecture, these questions and their possible answers are discussed.357"

Jan 1, 2013

By C. Riveros, H. Henein

Bulk Metallic Glasses have a high potential as advanced engineering materials due to their various properties including strength and corrosion resistance, to name a few. This paper investigates amorphous phase formation and rapid solidification characteristics of impulse atomized Co-based alloys in order to understand and control the application properties of the final products. Amorphous fraction and kinetic crystallization properties of the atomized Co-based alloy powders were quantified by means of Differential Scanning Calorimetry. In addition, different but complementary characterization tools were used to analyze microstructures of the powders. These include optical microscopy, X-ray diffraction and micro-hardness tests. While the amorphous fraction within the powders is promoted by high cooling rate and smaller powder size as expected, hardness is found to decrease with the fraction of amorphous phase.

Jan 1, 2015

By Ryan Montpellier, Paul Hebert

"Prospecting the Future: Meeting Human Resources Challenges in Canada's Minerals and Metals Sector is a comprehensive sector study of the short- and long-term human resource issues and challenges facing the minerals and metals industry. The study's in-depth assessment of current and emerging human resource needs and gaps served as a foundation for the recommendations designed to maintain the strength of the minerals and metals sector well into the future. The study provides insight and identifies strategies relating to each of the following areas:•,An aging workforce•,Significant retirements on the horizon•,Human resources demand growth•,Supply challenge - education and training programs•,Under-representation of non-traditional groups•,Supply advantage - attractive features of mining•,Supply and demand gap"

Jan 1, 2007

By D. G. MacBeth

Most belt scales on the market are factory calibrated to minimum accuracy figures of 0.1% - 0.2% at several load points. However, if the same belt scale is not properly installed and maintained on the customers conveyor then the scale will not measure up to the claims of the manufacturer or to the requirements of the operator.

Jan 1, 1975

By R. Simkus, J. K. Gowans

Polaris Operations, a Cominco Ltd. lead-zinc mine, is located on Little Cornwallis Island, Northwest Territories, at Latitude 75°23' N and Longitude 96°75' w. When the Polaris Mine went into operation in late 1981, it became the world's most northerly base metal mine.The Polaris Concentrator, housed in a unique process barge, is a basic lead-zinc concentrator where flotation is used to produce the lead and zinc concentrates.The paper describes the ""coarse lead"" flotation feature incorporated in the concentrator flowsheet and describes the start-up problems and continuing operation of this circuit.

Jan 1, 1984

By R. Bruce Ferguson

"IntroductionThe Beaverlodge Operation of Eldorado Nuclear Limited is a uranium property located near the north shore of Lake Athabasca about 7 miles from Uranium City, Saskatchewan.The mill is a 2000 tpd carbonate leach operation producing a high grade yellowcake concentrate.The Lamella Thickener was purchased to replace a 55 foot conventional unit which had deteriorated beyond repair. The cost of the unit was considerably lower than for a conventional unit, installation was much simpler and the unit is much more compact allowing it to be installed in the mill basement and be insulated completely.The unit was sized according to the results of tests performed both by the supplier and Beaverlodge engineering staff. The supplier guaranteed overflow clarities of less than 100 ppm suspended solids. The Lamella thickener was developed by A. Johnson Co. of Stockholm, Sweden, is manufactured under license by Parkson Corporation of Ft. Lauderdale, Florida and is distributed in Canada by A. Johnson Co. of Montreal."

Jan 1, 1975

By J. C. Loretto

"OPENING REMARKS Yesterday and today we have heard some very interesting papers on operating matters and some of you are probably wondering what we are now doing talking about Communications in Plant Design. Let me tell you! Before the techniques we have heard being discussed can be used, there has to be a properly operating plant. It is certainly a fact that many mineral processing plants achieve only limited success and a number of them can even be said to be failures. Some of you sitting here are probably living with operating problems that are clue to errors in the design.If the histories of these problem plants are examined, it will be found that in many cases, the necessary skills were available during the period of the plant design. There was extensive operating know¬ledge together with a full range of project expertise. Why then the failures? In a substantial number of cases it can be traced to the old, old problem of communications. As plants get bigger, money costs more and smooth startups become more important, it becomes less and less economic to fix up any design errors during plant operations.During our careers in mineral processing, nearly all of us will be involved in at least one plant design and I feel that it is as well if we understand some of these communication difficulties that can lead to a problem plant. There is little point in us being experts in mineral processing if the knowledge we have acquired doesn't somehow get incorporated into the plant.I would, therefore, like to present this short paper that mentions a few of the significant communication problems that can occur during the design of mining and mineral processing plants, together with some thoughts on answers to these problems."

Jan 1, 1973

By Linda Dufour

"Autoclaves have been in commercial use in the mining industry since the early 1950's the initial applications included tin, uranium, cobalt, nickel and copper extraction under both acidic and alkaline conditions. These circuits varied in batch or continuous operation. The geometry has been spherical, vertical, and horizontal type with up to six agitators, with throughput as high as 1000 stpd.Presently autoclaves are a good process selection for many refractory sulphide gold bearing ores. The first application of pressure oxidation in the gold industry was at the Homestake Mcglaughlin's Mine which was commissioned in 1985. This was an acidic pressure oxidation process treating 3000 stpd in three four compartment horizontal autoclaves 14' diameter and 53' long. Since the initiation of autoclaves for the treatment of gold bearing sulphides, there are presently 16 gold autoclaves operating worldwide varying in size up to 18'4"" inside diameter. There are seven autoclaves for the treatment of refractory sulphide gold bearing ores to be commissioned in 1997 and 1998.Autoclave technology has progressed extensively since the mid-eighties. Operational experience has made rapid progress and the result is much smoother and safer autoclave operation. There have been many advances in autoclave technology design. For example, the use of exotic materials for corrosion resistance to reduce down time for maintenance. The instrumentation involved in autoclave operation is very sophisticated which allows for many safety features. The advanced design has allowed for greater availability and as a result operating costs and maintenance costs have decreased. These technological advancements have made autoclave technology more safe and this has resulted in a greater acceptance of this type of operation. Many of the gold autoclave facilities operate up to 9 months continuously without shutdowns. The advancement of autoclave technology has inspired many new applications.Because of the outstanding operation of autoclaves in the gold industry, many other applications for autoclave technology are being considered. The following is a list of autoclave applications:"

Jan 1, 1997

By Frederik H. Kriel, John Ralston, Craig Priest

"Stream-based microfluidic solvent extraction offers a novel alternative to bulk-scale mixer-settler operations. However present maximum throughputs are restrictive and there are engineering challenges that need to be overcome before the technology is robust. This is especially the case for mineral processing, where circuits must be able to handle variable feed streams with long retention times and where maintenance should be minimized. This paper highlights research directed at investigating and evaluating these challenges for actual mineral leach solutions of metal ions. Molecular and particulate channel fouling is discussed. Most extraction systems studied to date show no effects that would preclude use of the technology. For rare earth elements (REE) with fast extraction rates, scale-up of volumetric throughput to 100 L/h using suitable arrays of channels, microfluidic chips and modules is shown to be achievable using a small contactor (approx. 2 m3) platform. This requires only 2–3 % of the typical aqueous phase inventory and residence time used in an equivalent mixer-settler. For a circuit with 100 contactors, the overall residence time would be less than 1 h, using an aqueous inventory of 40 L.INTRODUCTIONHydrometallurgy is of pivotal importance in many mineral processing circuits around the world, with liquid-liquid solvent extraction (SX) a key step in the separation of many base metals (e.g. Cu and Ni), radioisotopes, precious metals, and the ‘technology’ metals, such as rare earth elements (REEs) (Ritcey & Ashbrook, 1979). The standard equipment for SX in mineral processing is the mixer-settler, in which liquid dispersions are created, by agitation, to increase the surface-to-bulk ratio and, thus increase the mass transfer rate between the liquid phases. In stream-based microfluidic SX (microSX), these high surface-to-volume ratios are achieved by contacting microscopic streams (Ciceri, Perera, & Stevens, 2014), rather than forming small droplets, so that phase disengagement can be accelerated (essentially instantaneous via branching of the two streams of liquid at a channel junction). MicroSX is profoundly different from bulk mixer-settler SX operations and offers exciting opportunities for processing hydrometallurgy solutions (Kriel, Holzner, Grant, Ash, Woollam, Ralston, & Priest, 2015; Priest, Zhou, Klink, Sedev, & Ralston, 2012). Nonetheless, the advantages of using microfluidic environments are presently balanced by very significant challenges relating to throughput, process control, coupling of stages, flow stability, and fouling. If these challenges can be met using smart chip designs, process control and clever engineering, high-value/low-volume SX processes stand to benefit greatly."

Jan 1, 2016

By Godfrey MacDonald

"The East West Caribou deposit with an underground mine, concentrator and ancillaries is located 30 km west of Bathurst, New Brunswick. The Restigouche deposit, an open pit mine is 30 km west of East West Caribou. The ore will be trucked from the Restigouche site to the East West Caribou minesite.History:The East West Caribou ore body was discovered in 1955 and the subsequent metallurgical programme focused on producing a bulk sulphide concentrate. However, in 1966 a Mr. P.G. Kihlstadt of Anaconda did float a Copper-Lead concentrate and a Zinc concentrate. He also reported that as the grind became finer the recoveries improved. In 1968 the Mines Branch in Ottawa produced a Lead concentrate of 30 percent at a 60.5 percent recovery and a 52 percent Zinc concentrate at an 83.4 percent recovery.Laboratory testwork proceed the 1988 start up of our current concentrator and underground mine facilities. The concentrator was designed to produce a Lead ""rich"" concentrate and a Zinc ""rich"" concentrate which were combined to make a marketable Bulk concentrate. In 1990 the operation was suspended because of declining base metal prices, increasing smelter treatment charges, increasing operating costs and operating difficulties.The 1997 operating plan is to produce a Lead concentrate and a Zinc concentrate.The Restigouche ore body was discovered in 1989. The subsequent testwork done at Lakefield Research recommended the production of a Copper, a Lead and a Zinc concentrate. The ore reserve could not support a stand alone concentrator so the project was put on hold.Laboratory testwork was carried out at Lakefield Research to confirm compatibility of the East West Caribou ore and the Restigouche ore in their processing."

Jan 1, 1997

By James J. Roettger, Robert J. Mitchell

"The results of a series of model stope pours designed to investigate working pressures on bulkheads during hydraulic pouring of classified tailings backfill are reported. Total bulkhead pressures and fill water pressures were monitored under the condition of a fully saturated backfill. Similitude of the model testing is discussed and equations are developed to estimate bulkhead pressures under prototype conditions. The model results show that good base drainage, combined with a bulkhead setback, can reduce the expected bulkhead pressures to values such that timber or concrete block structures should be capable of supporting a saturated backfill. Introduction Bulkheads are used in underground running operations to block drift openings in order that hydraulically placed sand backfill can be contained in stope pours. Whenever possible, the sand fill is designed to have sufficient percolation rate so that excess hydraulic transport water will gravity drain out through the bulk headed drifts. This avoids costly decanting systems. Early bulkhead design assumed that the bulkhead pressure could be as high as 0h = Hy where H is the fill height and ""y is the saturated unit weight of the fill (Thomas et al., 1979)(1). A typical design pressure for a 50 m fill height would be 1250 kPa giving a design force of 12,500 kN on a bulkhead located in a drift of 10m2 in area . Typical bulkheads were 1 m thick heavily reinforced concrete structures formed and poured into a notched drift. Not only were these expensive structures but the associated problems of inside drainage systems and curing time delays increased production costs. As experience with bulkheads for large bulk pours increased and fill pressure measurements became available [see, for examples, Libby et al., 1975(2), Askey et al., 1978(3)] , 'free drainage' timber and concrete block bulkheads were designed. Substantial savings have been realized using these types of bulkheads but greater engineering design and monitoring of backfill pours is necessary to ensure that backfill pressures do not exceed the bulkhead design pressures.The effective and total stress components of fill pressure, the engineering concepts associated with the 'free drainage' design and some detailed design considerations have been discussed by Smith and Mitchell (1982)(4) . It is important to the safe use of these designs, however, that the basic engineering concepts be demonstrated and communicated to those responsible for the day-to-day backfill operations. This paper describes and explains observations from a series of model studies designed to measure bulkhead pressures in a saturated fill."

Jan 1, 1984

By C. J. Brown

"Access to the outside world is supplied by the Alaska Highway to continental Canada and the United States, the Haines Highway, and by the White Pass & Yukon Route to Skagway and Vancouver. Communities and mining developments located along the Alaska Highway are supplied daily by truck transport with commodities originating in Whitehorse, Edmonton, and Vancouver.The average payload on the Alaska and Mayo Highway is in the order of 16 to 25 tons and is subject to government regulations. Highway haulage distances to railhead at Whitehorse vary as does the direction. The Clinton Creek asbestos development is located 395 road miles north-west of Whitehorse whereas the United Keno Hill operation is 287 miles to the north. Cassiar Asbestos is located in Northern British Columbia at a distance of 357 miles south-east of railhead at Whitehorse. In order to service these various mines multipurpose highway vehicles have been designed to allow maximum backhaul of petroleum products. The White Pass & Yukon Route was established as an integrated transportation system from 1955 when it became apparent that three non-integrated systems (ship, rail and truck), with the various paper work and rising costs, could not continue to serve the needs of Yukon. Integration became the company policy and a system was developed. A special container ship (Clifford J. Rogers) was designed and built. This was the first specially built container ship in the world. The northern container integrated system was operational in 1955.In 1965 over 8.5 million dollars were spent in upgrading the container facility and the construction of a tanker-container ship designed specifically to serve Yukon and Northern B.C. This program was based largely on experience gained with the original container concept. Two tanker-container ships handled"

Jan 1, 1973

By Chris Rule

This paper tells the story of the rapid commercial application of stirred milling technology at Anglo American Platinum?s many Concentrators. The first stirred mill ? a 10 000 litre IsaMillTM; the largest at the time, was commissioned in late 2003. The project development work was presented at SAG 2001. This operation was ?proof of concept? and vindicated the decision to scale up the technology; allowing a rapid and extensive roll-out of mainstream regrind mills as well as several further flotation concentrate regrind mills, over the next six years. Currently 23 stirred mills are in operation with 64 MW of installed drive capacity ? this paper describes the projects? roll-out and the significant results achieved to date. Many operational problems have been solved along the way, some of these will be described. The introduction of the technology has seen a step change in metallurgical results and progressively decreasing operating costs.

Jan 1, 2012

By G. R. Rawsthorne

"The Con-Rycon mine is located on the north shore of Great Slave Lake in the Northwest Territories within the present city limits of Yellow-knife. Development work on the Con property started in 1936, resulting in a mine-mill complex which produced its first gold brick on September 5, 1938. Since that date 5,000,000 tons of ore have been mined yielding 3,000,000 ounces of gold. At present there are 220 employees at the mine.MineThe mine has 1.22 miles of vertical shaft, 41 miles of level development and 10 miles of inclined raises. There has been 1,000,000 feet of diamond drilling in search of ore. The temperature at the 4900 level (4400 feet below sea level) is 68 deg. F.The present mining method is cut and fill. The majority of the ore mined today passed through an internal winze before reaching the main shaft. The long haulage and double handling will be eliminated with the completion of a new shaft presently under construction to the 5800 level.MineralizationThe ore treated today is from the Campbell shear 1vhich is characterized by lenses and veinlets of coarse textured quartz containing some carbonate, sulphides and finely disseminated as well as visible gold. At the lower levels of the mine the arsenopyrite content in the ore is de-creasing with a~ increase in the levels of chalcopyrite and pyrrhotite."

Jan 1, 1974

By M. J. Michaud, M. J. Lavigne

"A cornerstone of any successful mining project is an understanding of the mineral assemblage and metal distribution comprising the deposit. Knowledge of the precise mineral/ metal zoning enables an operation to utilize different mining and processing methods optimized for different parts of the deposit. The Lac des Iles mine, located in northwestern Ontario, is one operation that depends on a good understanding of these issues. Current resources for the Roby Zone total 94.1 Mt grading 1.66 g/t Pd, 0.18 g/t Pt, 0.14 g/t Au, 0.062% Cu, and 0.053% Ni.The Roby Zone occurs within the gabbroic portion of the Lac des Iles intrusive complex and consists of three compositionally and texturally different ore types with variable PGE, base and precious metal contents. PGE occur as sulphides and bismuthotellurides in net-textured sulphides, coarse sulphide blebs and as finegrained inclusions within secondary silicates.Knowledge of the precise mineral/metal zoning has directly and indirectly improved several operational aspects, including resource modelling, mining, and processing. For example, metallurgical recoveries have been increased by up to 3% to 5% and concentrate grades have increased by up to 100%. IntroductionLac des Iles Mines Ltd., a wholly owned subsidiary of North American Palladium Ltd., owns and operates a 3000 t/d open pit mine and concentrate facility, located 100 km north of Thunder Bay in northwestern Ontario. The Lac des Iles PGE-gold-copper-nickel mine has been in commercial production since 1993 and in 1997, produced 1.8 million grams of palladium, 127 000 g of platinum, 114 000 g of gold, 438 000 kg of copper and 354 000 kg of nickel (North American Palladium Ltd., 1998).Under the Industrial Research Assistance Program (IRAP), a two-year study of the mineralogy of the Roby Zone was undertaken with a goal of improving the profitability of the mine. Geological mapping, petrography and geochemistry of the Roby Zone were completed during this study. Utilization of the detailed mineral/metal zoning identified as part of this study was implemented at the mine and shown to positively impact many operational aspects including mining and processing."

Jan 1, 2003

By G. R. Morin, A. R. Leggett

"In 2010, closure of the Kidd metallurgical plants along with structural changes to the historical ratios of payable metals led to a review of the operating targets at the Kidd concentrator. Previous operating data indicated that there was potential for significant revenue improvements by lowering the copper concentrate grade. An extended plant trial was carried out in 2011 to quantify the revenue impact of lowering the copper concentrate grade from 27% to 25% Cu, as well as identifying the lower practical grade limit. Analysis of plant trial results indicated that the process change increased net concentrate revenue by $2 M to $3 M per year at current metal prices. Increased revenue was primarily associated with higher silver recovery to the copper concentrate while the marginally improved copper recovery was essentially offset by increased zinc losses and concentrate treatment and freight charges.Details of the plant test work results are discussed in this paper along with the financial analysis of the revenue improvements. Key areas covered are major revenue components of the concentrate contracts, validation of revenue improvements through plant testing and sensitivity of the improvements to market and plant variables.INTRODUCTIONThe Xstrata Copper Kidd concentrator commenced operations in 1966 treating ore from the nearby Kidd volcanogenic massive sulphide deposit in Timmins, Ontario (Thompson, Amsden, & Chapman, 1978). Over the years, up to four separate grinding-flotation divisions were in operation with throughput rates peaking at 4.5 million tonnes per year of ore in the mid 1980’s (Kelebek & Francis, 1998). As the mine production decreased and grinding throughput increased operations were gradually cut back and since 1998 two grinding-flotation divisions have been in operation treating Kidd mine ore. One of the idled divisions has been intermittently used for custom milling operations, most recently the Ni/Cu Montcalm deposit, which was milled from 2004 to 2009. Current budget throughput rates, limited by mine production, are 2.4 million tonnes per year of ore grading 1.7% Cu, 4.3% Zn and 55 g/mt Ag. Concentrate production rates are 150,000 tonnes per year of copper concentrate and 155,000 tonnes per year of zinc concentrate. The Kidd mine is the deepest base metal mine in the world with mining operations down to 9600 ft.In 2010 the copper and zinc plants at the Kidd metallurgical site, which previously treated the concentrate production from the Kidd concentrator, ceased operation due to a variety of economic and market factors. Following the metallurgical plant closures the Kidd concentrator products were shipped off site for treatment. The majority of the copper concentrate is now processed at the Xstrata Copper Horne smelter in Rouyn-Noranda, Quebec with the majority of the zinc concentrate processed at Canadian Electrolytic Zinc Ltd. in Valleyfield, Quebec."

Jan 1, 2013

By G. A. Vissac

METHODS of coal preparation have been greatly developed and improved during the past few years. Under the pressing competition from substitutes that have been displacing coal as a source of heat or power, the coal industry has been able, in many cases, not only to hold its own but to regain much of the lost ground, by offering better products of a higher value. The purpose of this paper is to present, in a brief and simple form, the principles of the latest methods and machinery used in coal preparation, in order to enable the coal operator t0 select methods and equipment capable of solving his own problems in the most efficient and economical way. The paper will deal, in the main, .with coal cleaning. It must be emphasized, however, that a complete coal preparation study covers many other operations, such as handling, screening, de-dusting, dust-proofing, and ash-conditioning. Handling Coal From the producing face to the railway car, coal must be handled with great care, t0 prevent degradation, because the coarser sizes are not only easier to clean than fines but, for our markets, they are often the more valuable. Generally speaking, such care is less important or is unnecessary in the Old Country, where conditions are different. The best way to minimize breakage is to avoid gravity methods in coal transportation. All chutes in a preparation plant should be shaken mechanically, and cleaning processes requiring large surge bins must be avoided. De-Dusting De-dusting of coal is accomplished by the use of vibrating screens, fans, or classifiers, or by a combination of these. Fines below 1/32-in. (or coarser than this, with some coals) can very seldom be cleaned efficiently. Common practice is to discard them immediately, if the moisture content of the coal allows this to be done. Otherwise, they are liable to give unnecessary trouble, either in the form of dust or sludge, which are difficult to collect or to settle. Flotation is the only process which will effectively clean fines.

Jan 1, 1937

By R. H. O. Wagner

"This paper describes the bench testing, pilot plant studies of alternative flowsheets, to determine the feasibility of gold recovery, by carbon in pulp extraction, in the Schumacher Mill gold flotation tailings. The economics were calculated based on pilot plant recoveries and actual industry operating costs.The economics of the carbon in pulp treatment of the gold flotation tailings were not justifiable. The economics of desliming the gold flotation tailings followed by carbon in pulp treatment were marginal, but favourable. INTRODUCTIONPamour Porcupine Mines, Limited is a gold, silver and copper producer located in Timmins, Ontario. In 1983 the head grade of Pamour's gold ores averaged nine one hundredths of a troy ounce of gold per short ton.Pamour operates two area mills to concentrate the gold ores. Free milling gold ores are processed at the Pamour One Mine mill, whereas the refractory carbonaceous gold ores, and complex gold, silver, and copper sulphide ores, are processed through the Schumacher Mine mill.The complex Schumacher mill feed ores do not all react favourably to flotation methods, consequently this study was commissioned to investigate the feasibility of the carbon in pulp cyanidation of the Schumacher mill gold flotation tailings. These tailings contain ten to fifteen percent of the gold in the mill feed. During the study period, the average grade of the Schumacher mill flotation tailings was nine one thousandths of a troy ounce of gold per ton, or one quarter of a gram of gold per metric tonne."

Jan 1, 1984