Search Documents

By S J. Chen, N Jiang, Y S. Ding, F X. Li, D W. Yin, F Wang

This study assessed the deformation failure characteristics of rock-coal composites with different height ratios. Uniaxial compression tests were conducted using an acoustic emission monitoring system and XTDIC three-dimensional full-field strain measurement system. The results showed that with the increase in rock-coal height ratios, the uniaxial compressive strength of composite samples increased from 5.26 MPa to 14.61 MPa. The evolution of the deformation localisation zone of the composite samples is closely related to the initiation and propagation of the primary cracks in the coal samples. At the moment when the main fracture of the coal samples occurs, there is a large drop after the peak of the stress-strain curve of the composite samples, and the height of the rock samples increased to varying degrees, which indicated that the failure of the coal samples induced the rebound deformation of the rock samples. With the increase in rock-coal height ratios, the rebound deformation amount of the rock samples decreased from 0.042 mm to 0.008 mm, and the rebound deformation rate decreased from 0.210 per cent to 0.010 per cent. Meanwhile, the rock samples’ rebound deformation releases part of the elastic energy to act on the coal sample, further contributing to the destruction of the coal samples. Compared with single composite coal samples, the coal samples of the composite samples have much more failures. In addition, with the increase in rock-coal height ratio, the input energy density, elastic energy density, post-peak release energy density, and residual elastic energy density of the composite samples increased, the dissipation energy density decreased, and the percentage of pre-peak elastic energy density increased from 98.56 per cent to 99.86 per cent. These results revealed the deformation failure characteristics of rock-coal composite with different height ratios and provided a theoretical reference for understanding the underground dynamic rock failures.

Nov 29, 2022

By P D. Munro

The spatial distribution of ore with similar processing properties or domains within an orebody may be identified early in the assessment of an orebody to provide a sound basis for later development of the orebody. The assignment of domains in the primary sulfide portion of an orebody is often more difficult than recognition of the oxidised, supergene and related domains usually located towards the top of the mineralised volume. This paper will discuss some approaches to assigning domains within the primary sulfide portion of an orebody. The processing properties of each mining block will be known if the contained domain(s) and their proportions are known. The use of both physical and chemical ore properties to assign the domains is discussed. The domains based on similar processing properties do not necessarily coincide with geological zones assigned by geoscientists. As part of assessing the physical properties of ore, the modal analysis of the ore with respect to the valuable sulfide minerals and the sulfide and non sulfide gangue minerals has to be known, along with the traditionally used elemental assays for valuable and penalty elements. Two scales for determining other physical ore properties will be considered: the mesoscopic scale (examined by human eye) and the microscopic scale (examined via a microscope under high magnification). The strengths and weaknesses of the data obtained at the two scales are discussed in the paper. Broadly, data collected at the mesoscopic scale are much less expensive but the types of data available are more limited. Methods for evaluation of chemical ore properties are also discussed. After establishing a basis for establishing the spatial distribution of domains, variability testing is required to verify the integrity of the designated domains. In contrast, each block of ore in some orebodies has been assessed principally via the results of a laboratory separation on a number of drill core samples or composites from throughout the block, with minimal or no attention to the concept of domains.

Jan 1, 2008

There are a number of different mechanisms by which wetlands can immobilise the metals in mine drainage. Here, the biogeochemistry behind four of these mechanisms (adsorption, biological uptake, precipitation as oxyhydroxides, and precipitation as sulfides) is discussed from the perspective of sustainability. Moreover, treatment wetlands are considered as part of a larger system, also taking into account the source of the drainage and various aspects of the receiving waters. The biogeochemistry of different metal immobilisation mechanisms in wetlands determines what kind of drainage can be treated with success, and it also places an upper limit on the amount of metal that can be removed from the water phase per unit of time. This has important implications for the design of treatment wetlands, perhaps particularly in colder climates. A thorough understanding of the prevailing biogeochemical processes is essential when attempting to establish treatment wetlands after the closing of a mine. If a wetland is to be used as a sustainable æwalk-awayÆ solution, the anticipated change in treatment efficiency over time (as pollutants accumulate in the system) must be considered in relation to the expected changes in drainage quality. It is also important that the total metal immobilisation capacity of the wetland is not exceeded and that the integrity of the system is maintained, in order to minimise liberation of previously immobilised metals.

Jan 1, 2003

Mineral processing is at the hub of the exploration-mining-metals production system. Because of the large volumes of material processed, incremental technology investments can pay off better than for other parts of the system. However, much of mineral processing remains a 'black art', because we are behind in investing in modem technologies. Consequently, we have one of the best opportunities to improve efficiency and competitiveness through the application and transfer of technologies that have already been developed for other industries. The reluctance of minerals companies to place priority in our area is not because we lack new ideas; our senior management has not been convinced, based on our previous results, that such investments will pay off as well as other investment opportunities competing for the same resources. The key is the proper establishment of technology strategy and more effective transfer of technology. The presentation will identify the failure mechanisms of technology transfer and will present a model for improving the success rate, a prerequisite for raising the priority of mineral processing investment. Topics emphasised include strategy formulation, human resources planning, and total quality management principles applied to improving technology transfer.

Jan 1, 1993

It is a commonplace of our industry that prices of most minerals have been historically weak during the 1980s. The International Monetary Fund's index of prices of metals fell 25 per cent between 1980 and 1982, rose slightly in 1983, and has since fallen further. In December last year it was 37 per cent below its 1980 average. The few temporary exceptions to the mineral industry's malaise highlight the excess capacity, which largely explains the weakness of prices. The industry has painfully come to recognise that more satisfactory prices will not be restored until supply capability and demand move back into better balance. Mine capacity was installed in the expectation of much faster growth of demand than has occurred. For a variety of reasons mine and plant closures have been insufficient to restore equilibrium to the market-place. The industry may, therefore, have to resign itself to continued weak prices for some years more, at least by the yardstick of the 1970s. Growth rates of demand have slackened off in line with economic activity, and in response to continuing substitution and technological improvements. To the extent that the recent weakness of oil prices stimulates the industrial countries' activity, demand for non-fuel minerals may grow faster than most forecasters now predict. It is, however, much too early to say how long the weaker oil prices will persist, and even more difficult to estimate their probable effects. In typical post-war business cycles the usual response to recession was to batten down the hatches, and ride out the storm. Sooner or later, and probably sooner, demand resumed its previous trend path, and prices recovered. The market, in effect, bailed mines out of trouble; the more efficient could make attractive pre-tax profits whilst even the poor to mediocre could earn a satisfactory living. Prices rose at least as fast as general inflation, and in the early 1970s much faster. In retrospect those price rises of the early 1970s were historically abnormal but they did not appear so in the prevailing inflationary climate of the time. When the market failed in the early 1980s many of the hardest hit companies looked for scapegoats.

Jan 1, 1986

The optimisation and validation of shearer cutting methods is a time consuming engineering task. Many different parameters, of which not all can be controlled, can vary. The easiest solution, to increase the installed power and the longwall length, is not always the best. A different cutting method can increase the capacity without the need of new machines. The Department for Mining and Metallurgy Machinery at RWTH Aachen University therefore developed ProSL, the simulation tool for shearer and longwall operations. ProSL enables the engineer to create his own cutting methods and compare it with other methods. Machine-data can easily be varied to see the impact on the method. The research shows that sophisticated longwall methods increase the productivity of the system. The paper presents the results of the calculation with ProSL and shows how higher efficiency and lower costs can be achieved.

Dec 6, 2010

ON milling plants, where a large number of slime samples are collected each day, considerable work is involved preparing them for the assayer. The usual practice (as the material usually passes a 150-mesh screen) is to place the sample on a 30-mesh screen an 1 brush it through on to a cloth below. The sample on the cloth is mixed and a portion taken out for the assayer. A simple apparatus that would rapidly disintegrate and prepare these slime samples for the assayer was needed. The manufacturers of assayers' supplies appear to have overlooked apparatus for this class of work. To overcome the tedious preparation of slime samples by the above method, the writer devised the apparatus shown in the accompanying drawing (Fig. 1). It will be seen that the apparatus is a combination of a modified household flour sifter and a riffle sampler.The apparatus is made up in two parts, the top half consisting of a screen box carrying the disintegrator, and the bottom half a, riffle divider, the joints between the two being a slip-in fit. A lid is provided for the screen box. The disintegrator consists of an open drum, to which are soldered three rows of spring steel fingers. Each row has a number of steel fingers which, on rotation, press against the semi-circular screen in the screen box, forcing the slime particles through.To operate the apparatus an 8-in. sample tin is placed under each spout of the divider. The sample of slime, which is about 2 lb. in weight and usually in lumps, is placed in the screen box, the cover replaced, and the drum rotated about half-a-dozen times by means of the handle.The disintegrated sample is divided by the rifle divider into two portions, which are found in the tins under the spouts of the apparatus. One of these samples is taken, mixed on a sheet, and sent to the assayer.

Jan 1, 1922

By Ribicic M, Kocar F

Surface lakes or water accumulation present a possible threat for the flooding of the underground mining works. Therefore, the criteria that define the conditions under which no flooding of the mining works can occur are of vital interest to the miners. The authors present the criteria that they developed for the Velenje lignite mine, Yugoslavia, and that take into account the elastoplastic behaviour of the rocks and the natural stresses involved in the deformable strata between the bottom of the lakes and the mine works as well as the extent of the direct caving-in process resulting from longwall mining activity. Fi- nally a generalization of these criteria to the other rock and stress conditions is discussed.

Jan 1, 1988

Since the 1970s we have seen a marked corporate response in terms of the environment. In part this has come from regulation but it has largely come from stakeholders and the community. We now see a similar trend towards sustainability. The Brundtland (1987) definition of sustainable development provides a direction for advocates: the advance of human prosperity in a way that does not compromise the potential prosperity and quality of life for future generations. In my view its three essential components are: economic, environmental and community. The Global Mining Initiative and the contributions to the Rio World Summit and the Johannesburg World Summit on Sustainable Development indicate that sustainability is being taken very seriously by the mining industry. But does the minerals industry really embrace sustainability as they claim? There is a view that in reality sustainability is a non-event and that the triple-bottom line approach is only a convenient catch-cry for companies who are actually focussed very strongly on the economics part of the equation. Chemical engineers are showing a strong trend to more sustainable practices and the chemical industry has shown real commitment to research into developing sustainable processing systems. This requires a framework for thinking and design and the chemical industry is demonstrating true innovation as it moves towards æno wasteÆ technologies. Whilst there are limits to the rates of change that can occur the minerals industry should also be moving in a much more determined manner towards the notion of processing of products designed for whole-of-life cycle û with minimum/no waste. But is the minerals industry just paying lip service to the importance of research to sustainability?Several common themes influence the science and innovation agenda in Australia, which will affect the development and adoption of innovations by AustraliaÆs minerals sector. First is the well-proven link between peer-reviewed scientific excellence and commercial application. Second is the rise of multi-disciplinary Mode 2 research, which has developed in response to the complexity of problems faced by contemporary researchers, which are best analysed by combining expertise from two or more disciplines. Successful innovation outcomes, in any field, including minerals processing, is promoted by Mode 2 research which benefits from greater levels of networking and collaboration. Kofi Annan in his Message to the World Social Forum puts it very succinctly æThe way forward lies in finding constructive solutions togetherÆ.

Jan 1, 2004

By S Servant, T J. Bidwell

Paste backfill technology is gaining rapid acceptance in the Canadian mining industry. The authors were able to work on four different mining sites employing paste technology in their operation. In each site the paste backfill is prepared with very fine tailings containing significant amounts of sulphur minerals. The research program involved laboratory testing on samples prepared in the laboratory, on control samples obtained at the backfilll plant during pouring into the stopes and on core samples obtained from drilling in backfilled stopes. The laboratory testing provided detailed knowledge of the mechanical behavior of the paste backfill. The need for a means of measuring the in-situ mechanical properties of the backfill became clear. A review of various trials published in literature and an evaluation of available technology suggested the Cambridge Self-boring Pressuremeter. A first field campaign confirmed the efficiency and dependability of this instrument leading to the conclusion that it offers a very good method for the in situ measurement of paste backfill properties.

Jan 1, 1998

By T Nixon

A common problem for many mines is insufficient total primary airflow or insufficient airflow in the correct places as the mine changes over its life. This has a number of impacts on the business operation and may result in the need for a major and unexpected capital upgrade of the system, cancellation of a planned production increase, reduction in production targets, increased operating costs, failure to provide contracted metals to customers or acceptance of substandard conditions in the workplace. In some cases, it can even result in premature closure of the mine. In recent times, higher metal prices have given an expected economic boost to many mines, potentially prolonging their life but simultaneously requiring the mine to develop to deeper depths or requiring assets such as shafts and fans to have their service life extended. Insufficient primary airflow is a particular problem in deeper mines as the ventilation circuits become longer, more convoluted, have higher shock losses and the actual airflow requirements increase due to a combination of leakage, dispersion of the workings and the problems of managing the additional heat loads due to higher virgin rock temperatures and autocompression. This paper discusses the reasons why mines experience unexpected shortfalls in primary ventilation capacity with its associated impacts on metal targets, profits and frequently on the health, safety and morale of the workforce, as well as its productivity.

Jan 1, 2008

By J Szymanski, S Planeta

Extensive rockfill cylinder testing was performed to determine the effect that aggregate size, aggregate moisture, Portland cement, fly ash and cement dispersant addition has on compressive strength of a cemented backfill. In this paper ætwo-level factorialÆ and æcentral compositeÆ designs were used to determine the single and interaction effects that each factor have on the overall strength. The results from the designwork indicated that the per cent of aggregate fines had the greatest influence on the compressive strength of the rockfill cylinders. From the factorial design results, a compressive strength estimation equation was derived, which enables the strength to be estimated, given varying input values.

Jan 1, 1998

By P C. Pistorius

Previous mineralogical investigation of all effluent flotation streams of Mimosa mine (Zimbabwe) indicated that appreciable amounts of liberated platinum-group minerals (PGMs) of the Pt-Pd-Bi-Te class are not recovered û despite electrochemical measurements showing interaction between xanthate and such minerals. In this work, the flotation recovery of synthetically prepared Pd-Bi-Te was compared with that of chalcopyrite (a typical fast-floating mineral) and pyrrhotite (a typical slow-floating mineral), with microflotation tests. These indicated Pd-Bi-Te to be a fast-floater with flotation rates exceeding that of chalcopyrite. Predicted flotation rate constants (from the Ralston model) were significantly lower for small particles (with diameters similar to those lost to the effluent streams) compared with those of particle with intermediate sizes. This supports the suggestion that losses to effluent streams are caused by particle size effects.

Jan 1, 2005

By D Cioclea, I Toth

Coal mining can lead to the occurrence of spontaneous combustion events. If these events are not prevented they can give rise to fires that have major adverse effects on the mine plan. After studying the chemical structure of coal, the theories of self-ignition and of the oxidation reaction of the organic compounds, two new technologies have been developed for fire prevention based on the inhibition of coal oxidation. The first technology consists of spraying water drops mixed with inhibiting substances into goaves. The second consists of the infusion of a mixture made of several chemical compounds. Tests performed in situ showed the new inhibition technologies to be highly effective even for longwalls mining coal with a high reactivity from the point of view of self-ignition.

Jan 1, 2005

Over the last ten years geological and mining software products have evolved greatly. Software companies developing such products have focussed almost exclusively on the development of technical aspects of the applications, addressing geological, ore reserve estimation and mine planning problems. These specialist applications, and the many other new technologies that are being developed by a myriad of niche developers, are an essential part of todayÆs hi-tech mining operations. Technology is also being used in many other areas to improve the mining process and there is no doubt that tremendous advances are being made in all these fields. Yet there is something missing. The manner in which the technologies are used and implemented has led to the creation of many independent and inefficient æislands of technologyÆ where a variety of products from different vendors are used to address different, but related problems. Problems occur with unreliable information, data duplication, data redundancy and transferring data between applications that may be incompatible or even run on different computer platforms. These problems impede the flow and availability of information and hamper day-to-day decision-making by mine management. A solution to this problem is to take a holistic view of all the various technical applications and incorporate them into a single information technology solution. This solution must encompass all of the information requirements of a mining operation and must provide facilities that address much of the modern thinking about mine management, including strategic mine planning, value management, key performance indicators, and maintenance of a mineral balance sheet. Gemcom is developing an Integrated Resource Asset Management System (IRAMS), which is an enterprise-wide integrated computer system that encompasses various applications typically found at a mining operation. The core component of the system is a common, open, industry standard database that can be shared by many users from each of the different departments at a mine. Around that central repository are the primary applications that provide the mine with information it needs to operate. Ensuring that the information is reliable, accurate, shareable, timely and consistent will eliminate many inefficiencies, and provide significant benefits to mining companies. In turn these benefits will lead to significant improvements in decision-making, productivity and profitability for the operation. The initial version of the IRAMS system is currently being implemented at the De Beers Venetia Mine in South Africa. The system is being built around a core repository using the Microsoft æBack OfficeÆ architecture, and incorporates key technical applications from Gemcom, Whittle, De Beers Technical Team, Wenco and JKTech. The benefits of enterprise-wide systems have long been recognised in the commercial arena and enterprise resource planning (ERP) systems such as SAP, JD Edwards and MIMS are becoming commonplace in the mining industry. The more forward looking software developers and mining companies realise the need for efficient management of the information gathered during the mining process and can see that the concepts used in ERP systems apply equally to the technical applications as they did to commercial applications. The use of IT in the mining industry has expanded tremendously over the last five years as enabling technology and management acceptance has become more prevalent, and there is considerable room for dramatic growth over the next five years. The evolution of geological and mining software has now reached the stage where mines will yield the greatest returns by integrating the applications used in each area of their operations.

Jan 1, 1999

The liquid products of low-temperature carbonisation of coal are of variable composition, very much influenced by the rank and type of coal, and process parameters. In general the tar contains a high proportion of phenols and a low proportion of bases. The neutral oil is more analogous to a thermally cracked petroleum oil than to a high temperature tar. Present practice and possible future trends in the production of chemicals and liquid fuels from low temperature tar are reviewed in the light of recent work on the detailed composition of the tar The phenols and aromatics will probably continue to be of most value, with the bases a useful source of spec- ialty products. However the high aliphatic content of the neutral oil (particularly 1-olefins and n-paraffins) is bound to receive more attention for chemicals as well as for liquid Fuels.

Jan 1, 1969

By D Yuen, J A. D Connolly, T V. Gerya

Recent works suggest that dehydration of subducting slab and consequent hydration and partial melting influences the dynamics of mantle wedge. Plums originating form the subducting slab due to Rayleigh-Taylor instability are responsible for heterogeneous composition of the mantle wedge. Also, occurrence of partial melt in the mantle wedge can trigger dynamic processes like exhumation of UHP rocks in intra-oceanic settings or can influence characteristics of the subduction tectonic regime. An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation.

Jan 1, 2008

By Campbell D. L, Nutt C. J

The Delta two-degree quadrangle is located in west-central Utah, in the eastern Basin and Range physiographic province but near the intersection of the Basin and Range, Rocky Mountain, and Colorado Plateau provinces (Fig. 1). The quadrangle lies in the region of interior drainage that includes western Utah and most of Nevada, and, like the rest of that province, it has an arid climate. This work is part of the United States Geological Survey's ongoing CUSMAP (Conterminous United States Mineral Assessment Program) project in the Delta quadrangle. Trace-element geochemical data presented here includes information from approximately 600 heavy- mineral-concentrate and 2500 rock sample sites from throughout the Delta quadrangle.

Jan 1, 1988

By S M. C Verryn

The amount of raw material used in the production of cement can be reduced by partially supplementing it by pozzolanic waste material without changing its properties negatively. This paper discusses results of an investigation using slag from the Pt industry, from the production of steel using Midrex processes as well as fly ashes from different coal power plants in South Africa. These are blended in a 20 per cent slag or fly ash to 80 per cent cement ratio. The properties of the mixtures depend on the phase composition, chemistry, grain size and the sources of the materials. The results are promising, but show variable behaviour depending on slag and cement composition. Compressive strength tests as well have heat flow curves showing the hydration behaviour, indicating that 20 per cent addition of slag or fly ash to ordinary Portland cement is viable. There is a large potential to use slag in cement mixtures and this study can be used to develop cements that will positively influence CO2 emissions and help to reduce large slag and fly ash stockpiles.

Jan 1, 2008

By Rubisov DH

This paper is related to the problems of the mathematical modelling of vibrating screening process and to predicting the screening operation results. The authors propose a model of screening based on the interpretation of granular material segregation on a screen surface as an instantaneous process. Results show an agreement with laboratory and pilot plant tests. Derived formulae can be used for screen sizing and screening result estimating.

Jan 1, 1993