Search Documents

SOME notes on the works of the Electrolytic Refining and Smelting Company of Australia will no doubt be of interest to members of the Institute, more especially as much of the work is new to Australasia. As many of the members who may read this paper have not been in a position to visit works of this kind, and are consequently not thoroughly acquainted with all the operations carried on, the author has taken the liberty, in some cases, to enter into explanation which would otherwise be unnecessary. The works are situated at Port Kembla (New South Wales), about fifty miles south of Sydney, and are approachable both by rail and water. The Government has recently built a low-level jetty upwards of five hundred feet long, and intends installing at an early date an electrically operated portable crane to facilitate the handling of material to and from the boats. This will mean: a considerable reduction in the length of time that boats are laid up at the jetty. There are also under construction two breakwaters, which, when complete, will materially assist shipping operation...

Jan 1, 1910

By Mowat B. A

I lamata is within the Morobe Goldfield (7¦ 25' S, 146¦ 39' E) on the Wau (SB 55-14),1:250,000 scale map sheet (Fig 1). The deposit is 13 km SW of Wau, within the headwaters of the Upper Watut River, at an average elevation of 2000 m. The steep mountainous terrain is covered by dense tropical rainforest and access is by helicopter or by foot track. The deposit has been described previously by Wells and Young (1991) and 1)enwer. Leach and Mowat (1995). Data collected to late 1996 have been used to estimate an Inferred Resource of 9.2 Mt at 3.1 g/t gold using a cutoff of 0.5 g/t. This contains a high grade portion for which an Inferred Resource of 1.2 Mt at 9.7 grt gold has been estimated using a 5.0 g/t cutoff.

Jan 1, 1997

By Hargraves A. J

With increasing depth, stresses and stress phenomena are becoming more important considerations in Australian coal mining.A large number of compressive and tensile strength tests was made on coal and rock cubes cut from samples taken in various Australian collieries. In addition, an empirical impact strength test was carriedout on fragments of the same samples, to obtain a correlation with compressive strength.In one colliery, flat-jack measurements were taken to assess stresses in coal ribs and in the roof.INTRODUCTIONBy world standards, some of the New South Wales collieries are approaching depths of cover considered a maximum for bord and pillar the normal Australian coal mining method. Several South Coast collieries are winning coal at depths of about 1500 ft., and future operations are being planned at deeper cover. Some areas of these deep workings produce considerable quantities of seam gas.Phenomena associated with high stress and copious gas under pressure in the seam violent phenoma presenting a danger and a nuisance in mine working - have occasionally occurred, and the phenomena are being investigated as a whole (Hargraves, 1958), and separately as a gas problem (Bolt and Innes, 1959; Hargraves, 1962) and as a stress problem. This paper relates to the latter - to investigations into the strengths of coals and coal measure rocks, and into the stresses in and about coal seams...

Jan 1, 1962

By P Lever, D Hainsworth, H Gurgenci

The ACARP Landmark initiative has created the opportunity to advance the level of automation in the coal industry by first focusing on the core production area of longwall mining. A Landmark Longwall Automation project was commenced in July 2001. The major outcome of automation using on-face observation has been divided into ten outcome areas that have been fully scoped for a three-year initial project life. A major facilitating technology has been the implementation inertial navigation system (INS) technology that can map the shearer position in 3D. A focus of the project is to deliver a system that is at least as productive as the current most productive manually controlled longwall face.

Jan 1, 2002

Lime and Marble Limited was founded by the late T J McKee OBE and his family in 1935. The Company had its base in the high grade marble deposits on Takaka Hill, and was also shipping crushed limestone to the Auckland glass works, and supplying burnt lime for industry.

Jan 1, 1998

Experimental petrology may be used to accurately constrain PTX conditions in order to calibrate and understand geologic processes. This method may be used to answer postulated questions, by recreating known geologic conditions and observing changes in the experimental charges. The purpose of this project was to determine the eutectic composition and temperature in the ternary system PbS-FeS-ZnS ¦ (Ag2S), at ambient and elevated pressures and elucidate if the sulfides of the Broken Hill orebody may have been partially molten during highgrade (granulite facies) metamorphism. The study determined the eutectic temperature and composition in the system PbS-FeS-ZnS to be 800¦2¦C and 62.5% PbS, 30.5%FeS, 7% ZnS respectively, at one atmosphere, and the eutectic temperature at 27 kbars was found to be 960¦C¦10¦C, with a eutectic composition enriched in ZnS relative to the one atmosphere eutectic. the addition of lwt.% Ag2S to the system depresses the eutectic temperature to 772¦2¦C at 1 atmosphere and below 810¦5¦C at 5 kbars. The conditions of peak metamotphism for the cental and southern areas of the Broken Hill Block, New South Wales, Australia , lie above the solidus of the PbS-FeS-ZnS-Ag2S system, strongly suggesting that partial melting occurred in the orebody.

Jan 1, 1998

COMPRESSED air is held in high esteem by the mining engineer as a medium for the transmission of power. The transmission, however, is accompanied by a high percentage of loss. Of the total work done by the steam cylinder'in compressing the air inthe air cylinder, less than 50% is ultimately utilized by the machines underground. These losses are due to its essential and inherent properties as a gas. One of the sources of loss is that due to transmission through the pipes which distribute the air from the receiver to the various places where it is used. As the capacity and economic design of air-compressing plant are influenced by this source of loss, it may be of interest to give an outline of how estimates may readily be made'in practice of thediameter of pipes, quantity of air discharged, and the drop in pressure occasioned.In hydraulics we have a general formula given M Rankine's "Civil Engineering" :It was suggested, the writer believes, in the first instance by D'Arcy, that this formula could be made to apply to an elastic...

Jan 1, 1918

By K J. F Logan, P W. Leaman, B A. Tucker

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. The Nam San copper-gold deposit was discovered in 2011 and is a likely blind extension of the Permian age Phu Kham structurally deformed porphyry/skarn copper-gold deposit.The Nam San mineralisation is hosted within a dominantly sericite altered schist unit located to the north of the current Phu Kham open pit operation and is overthrust by an allochthonous barren cover sequence of limestone, granite and sandstone. Reinterpretation of the Phu Kham geology developed the concept of a possible telescoped porphyry copper-gold system at depth. Initial drilling intersected remobilised copper mineralisation in a basal conglomerate, confirming the concept. A reconnaissance vector array induced polarisation (IP) survey identified a deep chargeability anomaly from which a drilling target was developed from 3D inversion modelling of a detailed follow up dipole-pole-dipole anomaly. Drilling of the chargeability anomaly intersected the blind Nam San copper-gold mineralisation beneath the thrusted cover sequence.The key discovery parameters are the result of an integrated exploration program that included reinterpretation of the local stratigraphy, which developed the concept of a deep blind orebody, IP surveys capable of penetrating through the barren cover and a commitment to a deep directional drilling program to test these concepts and targets. The inferred resource remains open at depth, and further assessment will most likely be through underground development.CITATION:Leaman, P W, Tucker, B A and Logan, K J F, 2015. The discovery of the Nam San copper-gold deposit, Phu Kham, Laos, in Proceedings PACRIM 2015 Congress, pp 515–520 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

The Reefton Goldfield on the West Coast of the South Island of New Zealand was a significant gold producing area between 1860 and 1951. During this period it produced approximately 2.1 million ounces (67 tonnes) of gold. The largest single producer on the goldfield and the deepest mine in New Zealand, was the Blackwater Mine at Waiuta which produced 21 tonnes of gold. The Prolubition Shaft reached a depth of 878 metres (317 metres below sea level). The mine closed suddenly in 1951 with about 66 000 tonnes of are remaining in the stapes. Since closure there has been no attempt to determine the ore potential of the mine at depth. This paper summarises the geology, history and resource potential of the mine and sets out two options for evaluating the remaining resource. The options are either deep drilling from surface or recovery of the Prohibition Shaft and underground development and drilling. A schedule for each option is presented and discussed.

Jan 1, 1992

Fines and unnecessarily small rock fragments are created by as many as four identifiable breakage mechanisms which operate close to the charged section or sections of the blasthole. The peak blasthole pressure (Pb) should not exceed that value at which the rock starts to fail in compression. Excessive Pb values can be prevented by carefully selecting:1. the composition, density and/or diameter of the charge, and2. the initiation/priming system.The percentage of fines increases with:1. increases in the charge diameter:blasthole diameter ratio, burden distance, blasthole diameter, effective sub-drilling and size of blast, and2. decreases in blasthole spacing, stemming height and the length:width ratio of the blast block.Decked charges tend to reduce the percentage of fines.Excessive fragmentation is more evident in buffer blasting and sinking cut shots than in blasts fired to a clean free face. Initiation sequences which give effective burdens considerably less than drilled burdens encourage the minimization of fines, as does an inter-row delay time which promotes good progressive relief of burden.The wastage of explosive energy in creating fines is most pronounced where fully-coupled, energetic charges are fired in weak and/or highly porous rocks. This is especially so where forward movement of the strata is impeded by buffer rock, excessive burden distances and/or inadequate inter-row delay times.

Jan 1, 1979

By C D. Rawlings

An assessment is made of the potential for thick seam underground mining of black coal in Australia. A brief summary is given of the geo-mechanical environment and previous mining history existing in a number of areas of particular interest from the point of view of thick seam mining. A classification of thick seam mining methods is presented with emphasis on the critical geo-mechanical parameters influencing the performance of such methods. A summary is made of perceived geo-mechanical research requirements related to thick seam mining in Australian coalfields.

Jan 1, 1980

By A Kurniawan, A Sjadat and M Akhasyah

PT Freeport Indonesia’s Deep Ore Zone (DOZ) is a block cave mining operation that has been in production for 15 years. DOZ is located approximately 900 m below surface and has an average production rate of more than 5000 t/d. The footprint of the extraction level will ultimately be 900 m long and average more than 200 m wide. The undercut level is located 20 m above the extraction level.While developing Panel 1K on the northern portion of the extraction level, a major geotechnical problem was encountered when there was a change in lithology and an associated fault intersection. A large collapse of the hanging wall of the extraction level drifts occurred in the area of the fault intersection between February and March 2011. This was followed by a collapse of one of the undercut level drifts directly above the extraction level in May 2011.It was suggested that the best approach to mitigate risk during rehabilitation was to systematically open up the failed area under the protection of a steel set support system. To achieve this, approximately 60 t of grout was injected from the undercut level to fill the voids created when the rock mass between the two levels failed. A ground penetrating radar system was used to survey the condition of the rock mass between the two levels before and after the injection of grout. After the grout injection phase was completed to a satisfactory level of confidence, rehabilitation activities started on the extraction level by taking out the now consolidated material from inside the drift in 2 m advances from under steel sets initially constructed in secured ground.Controlled blasting was the key aspect to the success of the initiative to open up just enough of the drift to systematically support the rock mass before the next set was installed. The systematic support consisted of in-cycle shotcrete sprayed over mesh pinned to the exposed rock, as effectively as possible, with splitsets before spiling the next advance’s protection canopy with rebar. Once secure, a combination of steel set and pumped concrete was installed as the final support. This final support provided a safe platform to repeat the process until the failed zone was safely traversed.CITATION:Kurniawan, A, Sjadat, A and Akhasyah, M, 2016. Rehabilitation of the collapsed panel 1K north in the Deep Ore Zone block cave mine, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 763–768 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

A brief review is given of the history of the Colliery to date together with the reasons for the development of an additional seam.Investigations into the quality of the coal ami its suitability for the production of metallurgical coke and determination of the economic mining limits and coal reserves are discussed. The commencement of mining operations and the inter-seamarrangements necessary for the disposal of coal won are described with the stages in the opening out of the seam itself and the reasons for the installation of a 48-in. trunk conveyor belt. Choke and manning of face equipment are considered and also the work of secondary development and pillar extraction.It is concluded that with modern face equipment and conveyor belt lines, concentrated mining followed by immediate extraction of pillars is practicable and is giving excellent results at Burwood Colliery.INTRODUCTIONBurwood Colliery, the total holding of which now comprises some 3,140 acres of land and 1,450 acres of sea leases, has mined the Borehole Seam since 1883. The early work took place from Nos. 1 and 2 shafts at Glenrock Lagoon and later on at Nos. 3 and 4 shafts at Whitebridge to which the centre of operations shifted in 1893, shaft sinking at this latter area having commenced in 1888.As all the early operations were confined to the Borehole Seam, reserves of coal on this horizon had been considerably reduced by the mid 1930's, so a cross measure drift was driven to the Victoria Tunnel Seam which is about 300 ft. above the Borehole Seam, and fully mechanized coal winning commenced from the second seam in 1938. Subsequently this cross measure drift was extended to the Borehole Seam and complete mechanization of the south-west sections of this seam achieved by 1945.Four track mounted mechanical units were put into operation in the latter area and these worked in a southerly and...

Jan 1, 1958

It has been fairly firmly established (Fisher, N. H., 1945) that the fineness of the gold in any ore deposit varies with the depth from the surface at which the deposit was formed, and, as a corollary to this, that it is dependent upon the temperature and pressure at the time of deposition. This relationship is such that, under certain conditions, the gold fineness, taken into consideration with other recognised criteria, furnishes a very sensitive and reliable guide to the relative temperature of ore formation, at least within the epithermal and the upper part of the mesothermal range.Definition of Fineness.The fineness of gold is calculated in parts per thousand and refers to the proportion of gold present in the naturally occurring metal in the lode, which is actually a gold-silver alloy, containing usually about 10 parts per thousand of base metal and up to 500 parts perthousand of silver. A clear distinction should be made between fineness and gold-silver ratio. The latter refers to the total gold and silver in the lode as determined by assay and is usually expressed as the ratio Au:Ag. Only in deposits where other silver-bearingminerals are entirely absent, which occurs comparatively rarely, can the gold-silver ratio be used as a measure of gold fineness and, in many cases, the two have no relationship. For instance, in the Edie Creek area in New Guinea, the lodes formed under shallow epithermal conditions all carry gold 500 to 550 fine, although the gold-silver ratio ranges from 1:100 to 1:1, in places in adjacent lodes.Determination of Gold Fineness.The fineness of lode gold can be determined only after it has been separated from all other minerals. Amalgamation recovers gold fairly cleanly - unless native silver is present - and the fineness of amalgam bullion is generally a reliable indication of the correct fineness of the gold. If the use of plates is involved, the bullion may be adulterated, but the effect of any copper, or other metal, that may have been introduced can be cancelled by assuming that the gold and silver shouJrl add up to about 990 fine, or by ignoring the base metal content altogether, which varies little in naturally-occurring gold, and in calculating for comparison purposes all fineness figures to the basis Au + Ag = 1,000.The composition of bullion obtained from cyanidation is generally intermediate between the true gold fineness and the total gold-silver proportion as determined by assay of mine or mill-head samples of Cyanide solution dissolves other silver-bearing minerals and the fineness of the resulting bullion is thereby lowered. Consequently, the fineness of cyanide bullion rarely corresponds to the true gold fineness and is useless for diagnostic purposes, although it is a common fallacy to refer to the fineness of cyanide bullion as the fineness of the gold.

Jan 1, 1950

The commercial application of electrolysis to zinc sulphate solutions for the production of metallic zinc is a development ·of the past twenty years. Earlier attempts failed to give satisfactory results, chiefly because certain harmful elements were either not recognised as being present in the solution, or, if recognised, suitable methods of removal had not been developed. The electrodeposition of zinc from zinc sulphate solution is extremely sensitive to the influence of a great many factors, all of which appear to be closely inter-related.Some of these factors tend to minimise the necessity for a high degree of purity of the solution, while other factors aggravate the harmful nature of certain impurities.The relationship existing betweBn the various factors in zinc electrolysis makes a general discussion of the injurious effect of impurities very difficult since, under one set of conditions a given concentration of an impurity may be of minor: importance, where its under another set of conditions the same concentration of that impurity may prove dangerous to successful electrolysis.

Jan 1, 1934

By McLennan R. G

The principle of personal safety is as old as the human race. The application of this principle to industry is of much more recent origin, and may be said to be almost exclusively the product of the twentieth century. The enormous strides in technique and production mode prior to the turn of the century had been achieved without any real regard for the crippled human by-products of that expansive era. It was accepted that. accidents were inevitable and formed part of the price that must be paid for production. It was not until 1885 that the first Workmen's Compensation Act was passed in Germany making the employer financially liable for injuries suffered on his plant.With awakening social conscience came the first organised efforts to reduce accidents in industry. Early 19th century literature dealing with the development of powerdriven machinery and the growth of industry in Europe contains many references to the unsafe and unhealthy working conditions that accompanied the change-over from the home workshop to the industrial plant. By the year 1900, there were in Germany - and a little later in England governmental regulations dealing with the guarding of hazardous machinery. American industry, now the acknowledged leader in industrial safety, admits freely that when an organised safety movement commenced in that country, there was already a considerable amount of information available to them from European experience. The steel industry was well to the fore in this work, and in...

Jan 1, 1957

Extraction of copper from a chalcopyrite concentrate by means of a cupric chloride leach is described. Initially the concentrate is mixed with sulphur in a 9: 1 ratio, and heated to 350-400°C. This converts the chalcopyrite into more readily soluble sulphides, while the iron rejected from the chalcopyrite is transformed to pyrite, which is insoluble in the leach solution employed. A two-stage countercurrent leach using a leach solution of 1 M cupric chloride, 3.5 M sodium chloride, and 1 M hydrochloric acid extracts 98 per cent of the copper, if conducted at 105°C. Iron extraction is relatively low, the mole ratio of iron to copper extracted being 0.17, compared to 1.0 for unreacted chalcopyrite. After dissolution, copper can be recovered by electrolysis, cupric chloride leach solution being regenerated at the anode.Electrolytic power requirement is low, being approximately 0.5 kWh per kg of copper. The sulphur and, most of the iron entering as feed are rejected from the process in the form of pyrite, which remains in the leach residue.

Jan 1, 1974

The Kwademen Au deposit was discovered in 1977- 1978 following a regional geochemical survey carried out as part of a UNDP (United Nations Development Programme) and BUMIGEB (Bureau des Mines et de la Geologie du Burkina) mineral exploration programme. The climate in Burkina Faso is rather dry, with markedly seasonal rainfall averaging 800 mm pa in the Kwademen project area. The relief is low and the drainage poorly developed, so that soil sampling was preferred to stream sediment sampling. Rocks have been subjected to deep lateritic weathering, so that they are transformed into a mixture of Fe-oxides and kaolinite over depths varying between 30 and 40 m. At the regional stage, soil samples (30-40 cm depth) were collected a a 300 x 500 m grid. The Kwademen deposit was indicated by Cu, Zn, Mo and Au anomalies. Subsequently, an area of 9.2 km2 was covered by a detailed geochemical survey by soil (100 x 50 m) and auger sampling. The regional anomaly was fully confirmed, and subsequent drilling intersected mineralized ore shoots, justifying the establishment of an evaluation project led by the U.N.R.F. (United Nations Revolving Fund) in 1983- 1985.

Jan 1, 1988

By C De-Vitry

"The large Yandi channel iron deposit (CID) is located in the north-west of Western Australia and is currently mined via open pit methods. Drilling at Yandi is widely spaced and current estimates are mostly linear averages of the surrounding local samples. Linear estimates such as ordinary kriging (OK) based on block sizes that are significantly smaller than the dimensions of the drilling grid are less variable than the unknown reality (Armstrong and Champigny, 1989).Conditional simulation (CS) provides a series of plausible realisations that represent the actual grade variability at a small scale (eg 1 m + 1 m + 1 m). These simulations are very useful for a number of purposes, eg: optimising grade control, stockpiling and blending selection of optimal drill hole spacing assessing resource risk on contained tonnage and metal.At Yandi the major constituents of the ore (Fe, P2O5, SiO2, Al2O3 and LOI) are correlated to varying degrees. Independent CS of each assay variable will not reproduce these correlations. Reproducing the correlations (and the shape of scatterplots) is important if the simulations are used for the abovementioned purposes. This paper examines and compares various methods of CS that aim to reproduce the correlations between the assay variables.The CS methods evaluated in this paper are conditional co-simulation (CCS) using the linear model of co-regionalisation and two other, alternative multivariate simulation methods, which use min/max autocorrelation factors (MAF) or the stepwise conditional transform (SCT) to de-correlate assay variables before performing independent CS. It was found that CCS best reproduced the characteristics (histograms, variogram, scatterplots, etc) of the declustered drill hole data (Figure 1). Whilst simulation using MAF generally produced acceptable results, the method did not adequately reproduce the variance of the assay variables. The univariate statistics, histograms and experimental variograms were acceptable for simulations generated from the SCT. Bivariate statistics, cross-variograms and scatterplot reproduction for the SCT were unacceptable. The latter method produced inferior results because there were insufficient samples to obtain a reliable transform of the third assay variable in the transformation sequence.None of the abovementioned simulation methods provides good reproduction of all the scatterplots. This is due to the presence of clay pods, which cause some scatterplots to display two trends. These clay pods contain higher percentages of SiO2 and Al2O3 than the surrounding CID. The clay pods are generally smaller than the drill-grid dimensions. Thus their locations are typically unknown and they cannot be defined by manual interpretation, eg via wireframes. The locations of the clay pods were simulated via indicator CS. CCS was then performed separately for the clay pods and the CID. This significantly improved the reproduction of the correlation coefficients, the scatterplots and visually the simulation was more geologically realistic. Simulating the location of clay pods followed by CCS of assay variables is the recommended approach for simulation at the Yandi CID.CITATION:De-Vitry, C, 2013. Simulation of correlated assay variables - a case study from the Yandi Channel iron deposit, in Proceedings Iron Ore 2013, pp 137-148 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Aug 12, 2013

Wire rope, when used for hoisting on a mine is one of the most vulnerable units in the most expensive group of installations on the mine. With the introduction of hoisting on the Koepe sheave, a new technique was established. This innovation brought with it certain advantages which long had been recognized and which are being developed further.A need exists for the development of an infallible non-destructive testing device for wire ropes and it is axiomatic that the development and application of such a device should be coupled with the physical examination of mine hoisting systems. Therefore an integrated type of research programme is necessary in order to correlate the effect of shock loading with rope damage, which may be detected ultimately bynon-destructive means. This paper reviews certain historical aspects of investigations on this topic and it outlines a policy for research which can cope with a.c. or d.c. methods of excitation of the rope.INTRODUCTIONThe importance of wire rope in mining operations is often not fully recognized. A wire rope when used for hoisting in a mine shaft should be regarded as a "machine" forming part of a system of machines, and consequently it should be specified as such when it is purchased, it should be maintained as such during its working life, and it should be discarded only when it has done its duty and has been rendered either unsafe or uneconomic for further use.Every mine shaft, vertical or inclined, has in it one or more wire ropes which are used to transport men, material, and ore. Considering the long history of wire rope haulage and the large number of rope applications, it is a tribute to wire rope makers and to mine maintenance engineers, throughout the world, that not many serious accidents have occurred because of failure of wire rope. However, when a...

Jan 1, 1965