Search Documents

By Fuller P. G

The purpose and current practice of cable trusses in underground coal mines is briefly outlined and details of various cable truss designs are presented. The main part of the paper describes the in-situ performance of cable trusses installed as secondary supports in gateroads and recovery roads of longwall coalfaces. The performance analysis is based on the results of in-situ monitoring carried out at a number of sites at two underground coal mines within Australia. Truss performance has been assessed as load developed in relation to roof convergence, face position and time. Additionally, the influence of strata conditions, installation pattern/density, roadway layout and geometry have been taken into account. An analytical model has been developed to predict truss loads. The principal variables are listed and the basis of the model is described. Based upon behaviour observed in the field the model has been progressively upgraded and validated against measured performance. Guidelines on truss performance and factors which influence it are presented and the implications of these to the use of cable trusses is discussed. Possible methods for improving truss performance in certain strata conditions are outlined and some comments are made on the value of cable trussing compared to cable bolting in these Situations.

Jan 1, 1992

Until recently, nickel laterite projects have been largely ignored, due to their supposedly higher treatment costs compared with sulphides, and to their perceived processing difficulties. A number of laterite projects in the 1970s were abandoned because of high capital and operating costs, while others experienced severe technical difficulties. Conventional wisdom had it that laterites would not be exploited until most of the sulphide orebodies had been depleted. Why then, have Australian mining and exploration companies started a resurgence of interest in the treatment of nickel laterites? It all began with the Bulong project, which has been under study since 1987, while more recently two further projects, Murrin Murrin and Cawse, have been initiated and are being fast-tracked to take advantage of the current high nickel and cobalt prices. A further project in NSW, Syerston, has also been investigated at bench-scale, but no further development has yet been announced. All these projects have the following advantages: 1. Good location near a major mining centre and,reasonably close to power, water, roads, accommodation and a developed service industry. 2. Straightforward, low cost mining. 3. Low cost of acid or sulphur. 4. Good to very good cobalt credits. In addition, there have been significant technological developments in the design and operation of high pressure autoclaves and high rate thickeners, as well as solvent extraction and electrowinning technology. This has helped to decrease capital costs and technical risks, and has allowed the development of alternative flowsheets to the existing laterite operations (Taylor, 1996).

Jan 1, 1996

By Weber D, Knox PR

The criteria developed for the Argyle Diamond Mine process plant control system are reviewed. The control system installed is described along with a discussion of the method of implementation adopted. The control system was extensively tested prior to instal- lation at site. This approach led to signi- ficant time savings during plant commissioning and facilitated rapid escalation of plant production. The control system has performed satisfactorily with a high level of operator acceptance and basically satisfies the criteria Developed.

Jan 1, 1986

Lake Kopiago is located some 71km northwest of Tari in the Southern Highlands Province and lies on the northern edge of the Papuan Fold Belt. The area is underlain by middle Miocene carbonate and fine grained clastic sediments intruded by late Miocene hornblende gabbros.Two mineral deposits occur to the south of Lake Kopiago. These are the Bisamu gold prospect and the Wunaki zinc-lead gossan.The Bisamu deposit consists of a calcic skarn assemblage which is geochemically anomalous in gold, silver, copper, zinc, cobalt, bismuth and tellurium. The prograde mineral assemblage includes garnet, clino-pyroxene and epidote whereas the retrograde assemblage includes epidote, quartz, actinolite and chlorite. Pyrrhotite is the dominant sulphide with minor pyrite and marcasite and trace chalcopyrite and sphalerite. Minor magnetite is also present. The Bisamu skarn shows many of the features typical of gold-skarn type mineral-isation.

Jan 1, 1994

By Moore A. J

This paper describes the use of a wavefront reinforcement model which has been developed to supplement established charge mass scaling methods. The model allows for the time taken for blast vibration wavefronts to travel from each blasthole, and has been successfully used to explain the reason for directional increases in both air and ground vibration in certain situations. The model has been used to identify wavefront reinforcement due to the propagation of air vibration and ground vibrations in certain situations. The paper includes a throw (or cast) blasting case history which provides multi-station evidence of the strong directional nature of wavefront reinforcement.

Jan 1, 1995

By P Trotta

The paper provides a structured methodology to investigate metallurgical problems within the operating concentrators. The strategy uses classical metallurgical data analysis as well as pulp, solution and surface analysis to determine the reasons for particular behaviours. The approach applies equally to all mineral-processing operations. To demonstrate its effectiveness a case study, based on work conducted at Pasminco Rosebery Mine, is described. In this work, the classical metallurgical analysis indicated that a significant amount of sphalerite reporting to the lead concentrate occurred as liberated particles. A combination of pulp, solution and surface analysis supported the hypothesis that the liberated sphalerite was recovered by inadvertent activation by lead ions. Laboratory studies have indicated that the use of sodium carbonate, by itself and in combination with zinc sulphate and sodium cyanide, when added to the lead regrinding mill can depress sphalerite flotation, resulting in an improvement in the lead grade/recovery curve. When this approach was tested in the plant other more dominant issues masked any positive effect the addition of sodium carbonate may have had. The plant trial highlighted the real need for additional regrinding capacity.

Jan 1, 2002

By H Lemos, E Nunes, D Jacobson, R Costa, L Ono, A Alves, H Delboni Jr

Oversize rock breaking and metal tramp removal are key issues for reducing primary crusher downtime, as well as improving the safety associated with its operation. Remote operation of such tasks would thus not only increase productivity, but also reduce the risks related to work in confined spaces, fall risks, and overhead hazards. These issues are particularly relevant in high-capacity operations such as iron ore mining, where large machines are in continuous operation. This article describes the architecture, construction and advanced testing of a novel remotely operated robotic mechanism for assessment and removal of metal tramp from primary crusher chambers. The system essentially includes a robotic-arm equipped with a hydraulic clamp tool for handling oversize material, as well as an oxy-flame module for cutting metal pieces entrapped within the primary crusher cavity. The first industrial unit was delivered to a large iron ore mine in Brazil, where the installation and testing is scheduled within the coming months.

Nov 8, 2021

By Golab K, Partridge AC, Fletcher CAJ, Holtham P

Spiral concentrators are used globally in the fine coal processing industry to segregate particles, by gravitation, on the basis of density and size. Consisting of an open trough that twists vertically downwards about a central axis, a slurry mix of particles and water is fed to the top of the concentrator. Particles are then separated radially as they gravitate downward. Since their introduction to Australia in the 1940's, the generic design has evolved largely by laboratory trial-and-error investigations of different prototypes. However, this approach has proven expensive and optimal designs have not been necessarily developed. Accordingly, Computational Fluid Dynamics (CFD) analysis has been used recently as an alternative method of investigation, to assume as is envisaged, a role in the design process. To date, CFD models have progressed to simulations of turbulent fluid flow on current production spiral designs, and are continuing to be adapted for inclusion of particles at realistic feed concentrations. To be able to use the models confidently however, laboratory experiments must also be performed to validate the predictions during the development stage. This paper reports the current findings of an ongoing CFD and experimental program applied to one spiral unit. Satisfactory quantitative agreement has been achieved for the fluid and particulate flow characteristics, and although further validations are appropriate, the model already possesses significant potential for use as a reliable predictive design tool.

Jan 1, 1998

By Warren M

Many Australian tunnelling and mining companies regularly investigate different methods or equipment in an attempt to keep ahead of their competition. Sometimes the result is a new approach or process which wins a tender or provides an advanced solution to a problem.The Australian Government has a policy of encouraging forward thinking among Australian companies and provides a range of incentives. One of these incentives is currently available retrospectively to 1985 - 86, and the registration process is relatively simple with only one form to be completed. Companies who investigate methods of raising productivity could be reimbursed for the costs of the investigation.

Jan 1, 1993

The Snap Lake Phase I project initiated a subsampling campaign on the material (kimberlite/metavolcanic/granite) mined and treated for diamonds. The campaign was aimed at determining the optimum subsampling program to subsample the feed to the bulk sample plant (BSP) for the duration of a sampling campaign. This paper describes the application of GyÆs formula for determining the subsample size and other good sampling practices to determine this subsampling campaign. Three main issues are discussed: the use of a hammer sampler to sample off a moving conveyor and the practical experiment to determine the optimum subsampling program; bias introduced by laboratory equipment including two sizes rotary splitters; and variability of the feed material to the BSP over time.

Jan 1, 2005

The scope, pace and depth of mining is creating a need for improved ground control strategies to meet mine safety standards. Ground control and associated conservation problems relating to subsidence and the disposal of mining and metallurgical wastes can be resolved by mine filling with selected reject materials. The lack of suitable criteria to evaluate the applicability of such materials and especially cemented forms of fill is considered. Sulphide wastes, which are prone to oxidize, and cement are inexpensive mine fills, but their incorrect use can give rise to problems which are briefly described. Research work concerned with the utilization of sulphide wastes such as mill tailings, to produce fill with self-cementing properties has shown that the development of cohesion and strength is attributable to natural oxidation processes controlled by the physical and chemical composition of the fill mass. The cementing is caused by a number of oxidation products, and is most effective when the mineral pyrrhotite is present. The concepts of fill design are outlined and various criteria for assessing durability and deformational properties are proposed. Specimens prepared in the laboratory are capable of attaining unconfined compressive strengths up to 28 MN/m2.

Jan 1, 1973

In general, modern mining companies all over the world have to face the same economic circumstances as any other part of the industry: considering the tough competition, production and haulage costs must be reduced permanently whereas productivity has to increase substantially in order to remain price-competitive. However, the imposed pressure also offers the chance for consideration of alternative mining concepts, the application of which can result in substantial cost savings and improvements in the quality of the mined material. As one of these alternative mining concepts, surface mining technology offers substantial improvements in productivity. It also influences aspects of haulage, such as safety and speed, in a positive way. The capability of selective mining ties in nicely with the production of small-sized crushed material, the granulometry of which allows the elimination of the primary crusher. Mine operators profit from reduced costs for the maintenance of their haulage vehicles due to reduced wear, a decreased likelihood of accidents and higher average transport speeds. Surface Miners can also be used to cut haul roads into virgin rocks and leave a clean and level surface behind, improving the quality of these created roads. Thus, it is even possible to use ordinary road trucks for transport in mines. The current paper outlines in detail the effects of the surface mining technology on mining and haulage aspects and reports on applications where substantial cost savings could be achieved due to the application of what is also referred to as æsimple mining processÆ.

Jan 1, 2003

By A Domanti, C Jewkes

This paper describes the design and constructability issues investigated in the selection of a trenchless solution in comparison to trenched construction options as part of a scoping study for the augmentation of the existing Bulimba Creek Trunk Sewer in Brisbane. Initial work involved the planning of alignment options vis-a-vis ground geology, geotechnical conditions, location and depth of shafts considering potential construction technology, flotation and stability of the tunnel, availability of construction sites and the influence of construction works on neighbourhood properties and the immediate environment. Two design pipe sizes, DN1200 and DN1500, were considered, and factors including jacking forces, specification of product pipes, pipe joints, pipe jacking methods and the associated impacts of ground settlement were carried out. Of particular interest was research on suitable lubricating fluids with the potential to minimise jacking forces and maximise the length of pipeline between launch and reception shafts.

Jan 1, 2008

The Curragh coal mining operation was designed and constructed to produce two coals initially at a rate of 4.3Mtpa. These are a high thermal energy steam coal primarily for domestic electricity generation and a low ash high quality coking product for the export market. Treatment of coals from four seams to achieve this requires a large and complex preparation plant and blending facilities incorporating state of the art technology. This facility was constructed during 1982/83. It has been designed for expansion to 6.8Mtpa capacity. The preparation and handling facilities were built at a cost of approximately A$80 million. Equipment includes 500 plus electric drives with a total capacity of 20 000kw. Commissioning was carried out in three phases : Staging - of the control system Coal Handling Facilities - conveyors, stackers and reclaimers for raw and product coals The Coal Preparation Plant - heavy media cyclones and froth flotation. A period of three months was devoted to the commissioning of the plant before requiring product coal to contract specification. This paper will describe the planning, implementation and results achieved.

Jan 1, 1986

This is a welcome opportunity to exchange ideas about educating for a profession in mining and metallurgy, and I shall use it to highlight the ways in which educators, the industry, and the profession can help one another make that educa- tion better. This is home ground for me in more ways than one. As the executive head of a uni- versity perhaps I may speak as an educator; and there is still, I hope, enough of the metallurgist in me to allow me to speak of what we metal- lurgists and mining engineers can do to help the educators. Another interest should be declared, too. Among the educating agencies I shall focus on universities; among universities I shall further focus on my own, the University of New South Wales. I know it best; and, more to the point, we are one of the minority that offer a full profes- sional training in mining and metallurgy. Further, we are as a university very much concerned- more than most-with specifically professional education, and especially with education in the professions based on science and technology. Mining and metallurgy have of course played a central role, from earliest times onwards, in the history and development of science and tech- nology. In that role they have been both pro- ducers and consumers of new knowledge. Indeed the whole new attitude to knowledge that began to spread in 16th and 17th century Europe owed a great deal to the interests and traditions of the miner and the metallurgist. The first modern text- book of mining and metallurgy, George Agricola's De Re Metallica, is very much more than a spec- ialist handbook; it is a major landmark in intel- lectual and cultural history.

Jan 1, 1978

By Maidl B

A tunnel operations analyser is a new high technol- ogy instrument for use in underground work. By remotely sensing the acoustic emissions from operating machines and processes in a tunnel or shaft and by applying sophis- ticated computer processing to them individual process cycles and other detailed information about the operating processes can be collected. Detailed analyses and dissec- tions of the work in progress can be made and a variety of action oriented management reports produced. The pro- cess is fully automatic. Results of applying this device to two full scale tunnel projects are presented. The hardware and software that comprise the instrument are discussed in detail. Processes by which this device can be used to sub- stantially reduce tunnel costs are presented. It is concluded that this type of technology has great potential.

Jan 1, 1987

Coal geology plays an essential role in the investigation of in situ coal seam quality. Coal geology can also play an important part in laboratory studies such as coal washing and coking, and in operating plant problems.

Jan 1, 1976

Trial ore production began at the Hilton Mine in 1987 with ore being trucked into Mount Isa for treatment at the Lead/zinc Concentrator. The expansion of output from the Hilton mine required additional concentrator capacity which led to the design and construction of the Hilton Concentrator. Systematic laboratory and Pilot Plant testwork dating back to 1968 to develop a flowsheet and reagent regime suited to the varied and generally complex mineralogy of the Hilton ore was successfully concluded with a Pilot Plant trial using a sulphoxy based sphalerite depression system in early 1988.In May 1988, a decision was made to build a 750 000 t/y concentrator with some novel technological and capital-efficient features. The Hilton Concentrator commenced operations in December 1989 reaching target grinding rates and metallurgical performance by mid-1990. Current ore treatment rate is 800 000 t/y.Lead concentrates assaying 43 - 48 per cent Pb are combined with the Lead/Zinc Concentrator lead concentrates and smelted at Mount Isa. Zinc and Low Grade Middlings (LGM) concentrates are filtered in the zinc filter plant at Isa with those from the Lead/Zinc Concentrator and then railed to Townsville for export or treatment in Australia.

Jan 1, 1993

By Longworth C. R

This paper descrioes a case history of a coal mine which developed un'tahle roof conditions due to mass sliding of the overburden strata on a claystone band within the coal seam. The sliding is believed to have been initiated by stress relief associated with the removal of overburden alongside the entry portal of the underground workings. Once in motion, the roof block was kept moving by bulking due to roof collapse in the normal underground goafing operations. Control measures in the form of an earth and rockfill buttress against the entry portal and a sequential mining plan to create goaf areas alongside the entry portal have been initiated to attempt to limit movement. The operation has been continually monitored and a gradually decreasing pattern of movement is being re, orded.

Jan 1, 1981

By E du Plessis, J Kapusta, J L. Mauk

The world-class Bulyanhulu gold deposit (375 t Au) is in the Sukumaland greenstone belt, Northwestern Tanzania. The main mineralised quartz vein structure, termed Reef one, occurs at the contact of felsic metavolcanic rocks on the hanging wall and mafic metavolcanic rocks on the footwall. Reef one is dominated by massive quartz together with pyrite, pyrrhotite and minor chalcopyrite. Alteration in the footwall basalt is characterised by extensive chloritisation, calcification and silicification, which is strongest near the vein. Sericitisation also locally occurs adjacent to the vein. Metamorphic hornblende and plagioclase (albite) increase in abundance at a distance of 120 m from the vein and reflect the gradation into less altered rocks. The increasing abundance of chlorite, calcite, quartz and local sericite near Reef one, coupled by replacement textures suggests that most of these footwall minerals are the product of hydrothermal alteration, rather than regional metamorphism. Geochemical data shows slight enrichment in Ca, Fe and As towards the vein, whereas Zn in several drill holes becomes enriched away from Reef one. The Bulyanhulu gold deposit is a quartz-pyrite-chalcopyrite shear controlled vein with an adjacent extensive chlorite-quartz-calcite hydrothermal alteration zone (and a limited local sericite alteration zone) that passes to a hornblende-albite metamorphic assemblage further into the footwall.

Jan 1, 2002